Seagate Hard Drive Firmware Update for the drive model: ST1000LM024

Similar Questions

• 2950 HDD D80A Firmware Update for the dedicated hot spares

  I have a 2950 III with 8 Fujitsu 146 GB drives installed in a RAID 10 array. The first six discs are configured for use in a virtual disk with the last two records configured to be used as a dedicated hot spare. OMSA describes the version of the firmware of these two disks 0102. I ran the update of the firmware as described here:

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/product/PowerEdge-2950?driverId=F50fd

  The six drives in the virtual disk just successfully upgraded to the version of the firmware D80A. Two rescue disks have not been tempted. I tried to run the Setup again and Setup note that installed and packaged versions are both D80A, but OMSA said that two rescue disks are always at 0102.

  This is expected behavior? Spare disks are treated differently? If so, the firmware update as they are now or have I trade in the virtual disk to do the upgrade?

  The link does not work for me earlier... it's working now.  There is also a utility 'nautilus' which can be used on Dell readers... it will update all readers of Dell, regardless of the make and model... preventing you from having to download a dozen different services.

  Yes, that is why the update is a failure: Dell firmware cannot be updated with the firmware of the sale to the retail/credits, and retail/Generic firmware cannot be updated with the Dell firmware.

• Installation of the firmware update for the Belkin surf router

  I have a Belkin Surf F7D2401 router and a signal course vodafone. I have now had their talk with each other, but it seems that I have to update the firmware of Belkin, it doesn't let me do, seems it is a 'bin' extension and I'm stuck just what to do next

  You must go to the Belkin router and install it from there...

  http://www.Belkin.com/support/article/?lid=en&aid=5947

• Prevent Seagate hard drive possible breaks down!

  If your computer was purchased in 2008 and early 2009 and provided with a Seagate hard drive, you should read the next document in support of HP:

  Prevent disk errors not system on computers with Seagate drives

  Basically, under certain conditions the firmware of the drive can fail. It may work well for some time, but then crash later because certain conditions arise on the PC.

  To avoid a possible crash, download and install SP40966 from HP.

  Once opened, it will tell you if a player needs updating.

  If you have a player who needs the updated firmware, it will prompt for a blank disc.

  He then burns a disc that you leave in the drive and restart.

  It updates the firmware automatically. On some PCs/versions, you will have to perhaps enter and change SATA to IDE in the BIOS - I have not. I used the update on an IQ506 and the update went well.

  My problem has been resolved. I downloaded the update yesterday and installed without any problems. The closure of the issue.

• Compaq 8510w: replacement HARD drive models?

  Hello

  I have a laptop Compaq 8510w (KE186EA; s/n CNU812285Y) with 200 MB of HARD drive installed. It is a Seagate ST9200420AS ('Momentus' family).

  Yesterday, the CHKDSK utility found some bad sectors, so I want to replace the HARD drive. This Seagate model is no longer sold. What other HARD drive models are fully compatible with my laptop? My laptop has the peculiarity of "HP Drive Guard" who takes care of my HARD drive in the case of a shock, I wonder if this feature requires a 'special' model of the disk HARD must be installed.

  I searched the web site of Seagate and other Momentus drives are listed there, but I'm not sure that they will fit my laptop; for example, none of them does support "shock protection" (or this function Seagate has nothing in common with HP Drive guard?).

  UPD: and I also wonder if I can use an SSD, and if yes - what settings should it?

  -Generally shorter readers won't be a problem, since readers usually rise in a way where the screws and SATA connectors are located at the same locations despite the height of the car. Just be careful not to exceed the height of the OEM disk (i.e. some of the 1 TB + drives that were 12 mm of height not suitable)
  
  -SATA type is not important. SATA 3 Gb/s, SATA 6 Gbps or fastest readers will work fine, because their speed will be anyway limited by what the storage controller hardware supports.
  
  D ' a generally, capacity have no impact on the production of heat. The 8510w, as a workstation type system, is designed to use the commands of higher performance. Newer players tend to be more thrifty in energy which means less heat. You should have no problem of compatibility based on the ability for any player < 2 TB.
  
  Personally, I think that the benefits of the hybrid hard disks are largely overrated. If you want real performance boost, GB SSD - well worth the money, the performance difference is day and night from a physical disk more you don't have to worry about damage to the drive drops or movement.

• Qosmio G20 - how to find an update for the video card?

  Hi I can't find the update for the video card and when I run the game it hand me your video card drivers are too old.update them.
  my laptop:(toshiba Qosmio G20)
  My vidoe card: (NVIDIA GeForce Go 6600)
  Operating system: (Microsoft Windows XP Professional)

  Hey,.

  To be honest I don t understand your problem. Why visit nVidia?

  All you can download it from the download page of European driver from Toshiba as a boarder suggested. I even checked this and for Qosmio G20 and Windows XP you can get all the drivers no problem at all! :)

• Levels of firmware unsupported for the stepping of the processor of AMD family 10 h B2

  I just bought a machine with the following:

  -Card mother Asus M4N78 Pro

  -AMD Phenom X 4 9600 CPU

  -8 GB RAM

  -Sata drives

  I tried the following, all with the same error which results in the "levels of firmware unsupported for the deepening of the family 10 h CPU B2 AMD" loading.

  -ESXi 4

  -ESXi 3.5 U2 (I read on many forums after the 3.5 u3 firmware issues)

  -Version ESX available with the evaluation version of vSphere.

  I went through many discussions, describing this problem over the past two years.  Does anyone have a solution to this problem?

  I found a work around for 'not supported microcode levels' problem: http://communities.vmware.com/thread/236107?tstart=150

• 277dw Lasetjet MFP: Firmware Update for my Laserjet MFP 277dw

  This morning my printer has informed me of an update of the firmware, which naturally installed. The printer print is no longer because I have 3 party laser cartridges.  I had heard of tactics HP injet printers, but never thought that they would stoop so low just to force me to buy their cartridges, which for color laserjet, is very expensive.

  I currently have the following HP hardware:

  1. High-end ENVY Phoenix 850-065se Desktop (i7-5960 x)
  2. New portable high-end OMEN
  3. 277dw LaseJet MFP
  4. Chromebook 11

  I am also a partner HP started.

  How much chance do you think it is I will NEVER buy HP hardware again?

  If you use laser 3 rd-party cartridges, do NOT have the HP firmware updates.

  Find another thread to the M277 that seems to relate to yours:

  http://h30434.www3.HP.com/T5/LaserJet-printing/M277DW-supply-memory-error-all-cartridges/m-p/5766705/highlight/true#M294371

  The solution by the user in this one suggests a bad patch as opposed to a deliberate attempt by HP, third block laser cartridges.  It is more credible to me than what HP did with the OfficeJets.  He fixed in downgrading the firmware that atleast confirms that the problem is associated with firmware.

  I commented on another M252 thread on a similar power error message:

  http://h30434.www3.HP.com/T5/LaserJet-printing/how-to-revert-fix-recent-firmware-update-for-HP-colour/m-p/5809720#M297289

  I think its time to crush us this one and get a comment from HP support directly.  If you would be so kind as to contact HP directly through Chat or by phone, we can get an official and timely response.  Then share what you said with the rest of us.  The community can get the word out from there.

  I also found another thread dig deeper and providing a link to an old version of firmware, if you want to try it yourself:

  http://h30434.www3.HP.com/T5/LaserJet-printing/M277DW-supply-memory-error/m-p/5760229/highlight/true#M293984

• P1102w firmware update for XP required

  It seems that the P1102w needs a firmware update to run via Apple's AirPrint with several iPads & iPhones the rest of my family use.

  (Don't know why HP can't provide a new printer with the current version of firmare which is expired less than 18 months, but who can fathom the means of Silicon Valley?)

  So, will someone please tell me how to upgrade firmware ASAP?

  I don't see anywhere any software development of firmware for XP on the HPs support Web site.

  My PC is runnning Windows XP 32.

  There is a document containing instructions to update the firmware of the P1102w.  The document can be accessed here.

  The document advises one to download the update of the firmware from the downloads page, but none are listed.  However, I could find the update through the update of the firmware of laserjet webpage.

  Click here to access the page of the laserjet firmware update.  The P1102w is listed as a series Laserjet P1100.  I hope this helps.

• I don't get updates for the retina of my macbook pro 15 mid 2015 2.5 processors 16 g ram, last updated, I got was garage to April 8, may be there is no more updates at this time, but what made me think twice this app a player have updated when trigger

  I don't get updates for the retina of my macbook pro 15 mid 2015 2.5 processors 16 g ram, last updated, I got was garage to April 8, may be there is no more updates at this time, but what made me think twice as more than one reader app have update to search for the app store When news, nothing happened and onedrive will not be updated, and this dose of update does not appear in the section updates in the app store app

  any body can help?

  That's what I have in the last few weeks

  

  Make sure you have a good WiFi connection and are signed in iCloud / App Store

• Excite the situation of update for the AT10LE - A-&gt; Pro

  Hello

  I was wondering about the status of update for the Toshiba excited Pro.

  _Specifically: _

  -It's going to be an Android 4.3 or 4.4 update? After all, it's a tablet of the premium segment, and I expect the usual level of support. Another manufacturer usually release one or two updates.

  -is yet to come miracast? He promised during the liberation, but then he got the silent about it.

  -the problem of thermal regulation has finally been resolved? Again, this is not rocket science, other manufacturers seem to be able to produce pills that work without overheating.

  -It will never be a way to root it or unlock the bootloader?

  I'm sorry if this seems critical, but given the reviews I had read, I think that these issues are very relevant.

  Updates for both devices excite Pro 3 G and WiFi were released last week.

  Excite Pro AT10LE - A WiFi-> update V4.3.001120220.05
  Excite Pro 3G AT10LE - A-> update V4.3.201121220.35

• A security update for the 2007 Microsoft Office System (KB976321) __Update to filter junk e-mail in Microsoft Office Outlook 2007 (KB981726)

  Update of security for Microsoft Office System 2007 (KB976321)
  Update for the junk e-mail in Outlook 2007 (KB981726) filter

  I have problems with the loading of these two updates on my computer.  Whenever I try, I get an "update failed" notice.

  These are the two only updates with that never got hurt.  I have a notebook hp compaq with Windows Vista.

  Flawed updates or am I doing something wrong or need to change a setting somewhere?

  Thank you, Bob

  http://www.Microsoft.com/downloads/en/default.aspx

  Put the KB numbers in the search at the above link > download them manually.

  If this does not solve it:

  Windows Update Forum:

  It comes with Vista, upgrade install and activate Forum.

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• Updates for the 2007 Microsoft Office Suite (business)

  My updates of Windows there are two available, when important updates downloaded and installed, Windows Update tells some updates have not been installed.  Failed: 2 updates.  Code 80070641 Windows Update encountered an unknown error.  The Microsoft® 2007 Office Suite Service Pack 2 (SP2)

  Download size: 207.4 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Service Pack 2 provides the latest updates to the 2007 Microsoft Office Suite.  This update applies to Microsoft Office Project, Microsoft Office SharePoint Designer, Microsoft Expression Web, Microsoft Office Visio and Visual Web Developer.

  More information:
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=B444BF18-79EA-46C6-8A81-9DB49B4AB6E5&displaylang=en

  Help and Support:
  http://support.Microsoft.com/?ln=en-us

  and:

  Update for the junk e-mail in Outlook 2007 (KB968503) filter

  Download size: 3.3 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  This update provides the filter of junk e-mail in Microsoft Office Outlook 2007 a more current definition of which e-mail messages should be considered junk e-mail.

  More information:
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=04C02D0A-B1AE-4097-9643-81968081DD9C&displaylang=en

  Help and Support:
  http://support.Microsoft.com/?ln=en-us

  Now, I've exhausted my options here, can someone please inform me as to how I can solve this problem?  I respectfully request for a known solution, not what you think will solve the problem.  My OS is Vista Home Basic 32-bit.

  Thanks in advance to anyone who can solve this problem.

  Hi sallampat,

  Thanks for posting the Answers.Microsoft.Com Community Forum.

  I suggest start in a cleanboot, then try again your updates.  Download updates to a folder on your desktop, then start in a clean boot, then try the updates.

  We will follow the following steps

  1. start the CheckSur tool by - http://support.microsoft.com/kb/947821

  2. download the updates you referenced from this site: http://www.microsoft.com/downloads/details.aspx?familyid=04C02D0A-B1AE-4097-9643-81968081DD9C&displaylang=en and http://support.microsoft.com/kb/953195 download them and put them in a folder that you create on the desktop of your system.

  3. start your system by using the cleanboot procedure described below;

  To perform a clean boot on a computer that is running Windows Vista, follow these steps.

  1. Click Start
     type msconfig in the Search box and press ENTER.

     If you are prompted for an administrator password or a confirmation, type the password, or click continue.

  2. On the general tab, click Selective startup.
  3. Under Selective startup, clear the Load Startup items check box.
  4. Click the Services tab, select the hide all Microsoft Services check box, and then click disable all.
  5. Click OK.
  6. When you are prompted, click restart.
  7. After the computer starts, start the program or game and see if the problem is resolved.

  (Here is the article from the base of the boot process minimum - http://support.microsoft.com/kb/331796 - after troubleshooting is completed, use the steps listed in the knowledge base article to restore your system back to the normal mode).

  4. when your system is loaded into a clean boot - run an update at the same time in the folder that you downloaded on.

  After completing updates or to work on the updates that your system to a normal operating state, following the process of clean boot above, but turn on where to disable services were selected previously.  (The KB describes the entire process.)

  Please keep us informed on this issue if more information is required.

  Kind regards

  Debbie
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Updates for the NET Framework 2.0 updates does settle

  I have been reminded of the updates for the Microsoft.NET Framework 2.0 SP2 server 2003 and Win XP x 86.

  Do not install the security updates.

  Flawless number only "don't not instaled.

  I checked with the different advise on services to update, but it won't help.

  Any help out there?

  John.

  From Internet Explorer

  Original title: updates will not be installed

  Error code '0x8007066A' when you use the Windows Update Web site or Microsoft Update to install the .net Framework update:
  http://support.Microsoft.com/kb/2507641/

  When you try to install an update for .NET Framework 1.0, 1.1, 2.0, 3.0 or 3.5, you may receive Windows Update '0 x 643' error code or error code Windows install "1603".
  http://support.Microsoft.com/kb/923100

  When installing updates using Windows update or Microsoft Update you may receive error 80070643 0 x or 0 x 643
  http://support.Microsoft.com/kb/976982

  more information: http://taurarian.mvps.org/Framework/Net_Framework.htm

• NET framework 3.5 service pack 1 & net framework 3.5 family update for the net version 2.0 to 3.5 (kb951847) x 86(update1 of 1)

  NET framework 3.5 service pack 1 & net framework 3.5 family update for the net version 2.0 to 3.5 (kb951847) x 86(update1 of 1)

  Hello

  1. what exactly is the problem you are having?

  2. do you have an error code?

  3. do you get an error message?

   
  I suggest you install the standalone product of the update and check if it helps.
  
  Microsoft .NET Framework 3.5 Service Pack 1
  You can download the stand-alone version of the link below: Microsoft .NET Framework 3.5 Service Pack 1:
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=22
  Microsoft .NET Framework 3.5 Family Update for Windows XP x 86 and Windows Server 2003 x 86
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=10006
   

  For reference:

   
  When you try to install an update for .NET Framework 1.0, 1.1, 2.0, 3.0 or 3.5, you may receive Windows Update '0 x 643' error code or error code Windows install "1603".
  
  http://support.Microsoft.com/kb/923100
  Problem installing .NET Framework 3.5 or 3.5 SP1 on checked, or pre-release versions of Windows Vista or Windows Server 2008:
  http://blogs.msdn.com/b/astebner/archive/2008/08/25/8895729.aspx
   
  I suggest you to give us more information about the issue to have a better understanding.
   
  I hope this helps.