Second update OS 9.3?

Similar Questions

• Nexus 5 K running 5.2 (1) N1(8b) affected by the second update? -CSCub38654

  I have a client that is running version 5.2 (1) N1(8b) and wanted to know if it is the affected versions.

  Release of Nexus 5 K known affected:

  5.1 (3) N2 (1 c)
  5.2 (8) N1 (1)

  Release of Nexus 5 K known fixed:

  5.2 (1) N1 (8.156)
  5.2 (1) N1 (9)
  6.0 (2) N1 (1)
   
   

  CSCub38654 - N5K switch upward hang/lock may occur because the second update https://tools.cisco.com/bugsearch/bug/CSCub38654

  Our NX - OS versions are not on the list either but to play it safe were disable NTP from June 29 to July 1, in any case, if your not sure TAC it

• A second update manager...

  Hello

  We have a vCenter server and ESX on 2 different sites. All ESX are connected to the same Virtual Center. VUM is installed on the vCenter server.

  Site 1: Server vCenter, ESX, VUM

  Site 2: ESX servers (connected to vCenter Site 1)

  VUM works very well for ESX in the same site (site 1). But pushing updates to site 2 is too slow.

  So, it is possible to add a second site 2 VUM server if all ESX servers are connected to the same vCenter?

  Or I need to install a second server vCenter Site 2 and separate completely the two sites?

  Thank you

  Hello

  Dentifrice1 wrote:

  Hello

  We have a vCenter server and ESX on 2 different sites. All ESX are connected to the same Virtual Center. VUM is installed on the vCenter server.

  Site 1: Server vCenter, ESX, VUM

  Site 2: ESX servers (connected to vCenter Site 1)

  VUM works very well for ESX in the same site (site 1). But pushing updates to site 2 is too slow.

  The issue may be due to the latency of the network between the two sites.

  So, it is possible to add a second site 2 VUM server if all ESX servers are connected to the same vCenter?

  Or I need to install a second server vCenter Site 2 and separate completely the two sites?

  You need to install a different vCenter in the second site, and then install VUM with her. This is because each VC can have only a registered VUM with her and vice versa. The VC and AUVS should be of the same version as well. Thus, a single instance of VUM does not work with more than a VC.

  Thank you.

  If you have found this unit or any other answer useful, please consider to allocate points for correct or helpful answers. *

• Second update statement is not updated all records

  Hello
  
  I've written a procedure for updating a table "REFDUMP". The second statement to update the id of the procedure does not update all records. It updates only few records about 3500 off 15967.
  
  Please can someone help me in this.
  
  
  create or replace PROCEDURE refdump1
  AS
  cursor c1 is select r.REF_QUARTER, q.QUARTER, r.reference_date, refdump r.created r, q quarter
  where nvl (r.reference_date, r.created) = q.REFERENCE_DATE;
  
  cursor c2 is select r.REFnom_QUARTER, q.QUARTER, r.NOMINATION_DATE, refdump r.created r, q quarter
  where nvl (r.nomination_date, r.created) = q.REFERENCE_DATE;
  
  SLIDER C3 is SELECT * FROM country_region;
  
  
  
  BEGIN
  BEGIN
  I'm looping c1
  UPDATE refdump
  SET ref_quarter = i.quarter
  WHERE (reference_date, CREATED) = nvl nvl (i.reference_date, i.created);
  COMMIT;
  end loop;
  EXCEPTION WHEN others then
  DBMS_OUTPUT. Put_line (' error in the update of the quarter Ref');
  END;
  
  BEGIN
  I'm looping c2
  UPDATE refdump
  SET refnom_quarter = i.quarter
  WHERE the NVL (nomination_date, CREATED) = NVL (i.nomination_date, i.created);
  COMMIT;
  END LOOP;
  EXCEPTION WHEN others THEN
  DBMS_OUTPUT. Put_line ('error in the update of the quarter of nomination');
  END;
  
  BEGIN
  UPDATE refdump SET oracle_ovi = 'other '.
  WHERE oracle_ovi is null.
  COMMIT;
  END;
  
  BEGIN
  
  I'm looping c3
  UPDATE refdump SET country = i.country_name2, region_cluster = i.region_cluster, region = i.region
  Superior WHERE (countries) in (upper (i.country_name), upper (i.country_name2));
  COMMIT;
  END LOOP;
  END;
  
  BEGIN
  UPDATE refdump SET country = 'other '.
  WHEN the country is null;
  COMMIT;
  
  UPDATE refdump SET region_cluster = region, region = substr (region, 1, instr(region,'-') - 2).
  Countries WHERE = "other";
  END;
  
  END;
  
  
  Thank you
  Vikas
  

• Error of the value of the range of the attribute only on the second update of the value each time.

  I tried to create an interface to change attributes of my camera during the acquisition. I created a cluster that has orders for BinningX & Y, cadence, exposure and position. When the VI running everything works fine except when changing the value binning more than once, I always get an error on the second attempt. The range is from 1 to 9 and at the beginning of the VI I can't change any value in this range, but if I try to change it to something else after that, even at 1, I get an error that the value is out of range. Any idea what could be the cause?

  Is attached a screenshot of part of my VI which deals with changing the values.

  Thank you!

  Change the order in which you pass in parameters. I had this problem several times.

  Indeed, if the return on investment that you describe is out of the detection area, you will get this error.

  Do not forget that the X offset + width cannot be greater than the width of the sensor and Y Offset height cannot be greater than the height sensor.

  Hope this helps

• last updated 10.10.5

  Hi all

  I'm a bit confused! (Not hard)

  I ran the last update and on my on this drop-down list box mac I tells me I am running version 10.10.5 yet, according to the list of updates installed on September 14, I have version 12.5.1

  When I tried to download an app on the App store it says I can't because I need OS X 10 11 or later version.

  So my logo Apple drop-down box says that my version is 10.10.5

  my list of updates in the last 30 days, say the of it downloaded 12.5.1

  Which one should I?

  Thank you

  Tricia

  The second update is an iTunes update, not an update to OS X. The latest version of Mac OS X's El Capitan, which you can download from App Store.

• My Equium A60 not startup after Windows update

  Hello.
  I have an Equium A60 (PSA67E) about 1 years. There has been many problems with this one recently. First, there was the problem of overheating. The machine would heat up and stops by itself without any warning. I tried many options by keeping the cooling ports clear but dint help not at all.

  I've recently updated my bios version 1.90 such suggested by Toshiba. I always see overheating so far after the bios update.

  The most annoying is the display driver which is in this case a lack of mobility radeon ATI 7000. This would cause the display to become oversized and the resolution is very low. It would go without saying when I restart the machine.

  Last month, I reformatted the machine using the Toshiba Recovery CD. Everything went well until I am passed on the automatic update of windows. The first update coming, and I install and reboot the machine to let it function. He's fine. Comes the second update is installed and I have proceed to restart to allow functional upgrades, it does not start. The machine keeps starting over and over again without loading the OS. The screen is the typical Toshiba boot screen with the yellow light (charger) on the screen and after some time a blue screen is delivered for a short time (I am unable to read this error message it is said) and the machine starts start again. What can be the problem?

  I need to install windows XP SP2, and for this I need to go through the Windows Update. What can be the remedy and on the update of the available display driver. I tried, but it makes the situation worse.
  I used the recovery CD at least 20 times that there is no alternative. I tried to start in safe mode but din't work.

  Hi, Germain,.

  According to your description of the problem it doesn't seem to be anything wrong with what you have done so far, but I just want to clarify a few points.

  1. After installing the recovery CD system you install/activate your anti-virus software?

  2. are you using Windows Update in automatic mode or you manually select the update process?

  I recommend you to turn off automatic error (Advanced tab in system properties) reboot so the system will not attempt to restart when you get your blue error screen. This will allow you to see what error.

  Kind regards

• After the last update of BIOS that Satellite P100 locks with BSOD

  Hello

  Due to several problems meeting with updated Toshiba Satellite P100-221 (PSPA6E) launch second online BIOS updated. I have download and I solve problems with my video card and the race of missing keyboard. After a short period, they put on the update of the BIOS rd page 3 drivers.

  I'm trying to find what ever they change with this new update, but I na? t find anything. So I decided to update my BIOS again. Now as a result my system crash very often when I quit & restart my computer (blue screen).

  Microsoft advised me to reduce the video acceleration for video adjustment.
  Maybe can someone explain to me why I have this problem?
  I use the same drivers and software same as in the second update
  I can find BIOS previous to rewrite again, because this one works very well with my laptop?

  Thank you!

  Hi Sebasian

  I use very long books and I've never updated the BIOS if not necessary. What laptop works well, OS stabile, why should I do it? I don t care if new BIOS update is available or not. I've always been skeptical about the updates to the BIOS. That's just my opinion.

  As far as I know, it is not possible to downgrade the version of the BIOS without special tools and it can be done by service partners. It is not easy to tell if the BIOS is responsible for this, but if possible, try to send us illustrated if BSOD errors.

  If I were you I backup all important data and reinstall the recovery image, configure OS for my needs, and make sure that everything is clean pre-installed. My experience with BSOD were always related software.

• Can I add a second HARD Satellite A200 - 10 X drive?

  Can I add a second HDD of my A200 - 10 X?

  Remove second HDD downstairs and check if the SATA connector is there. If there is no SATA connector for the second update of HARD drive with the second HARD disk cannot be done.

  Good bye

• Updates... Which one to choose?

  If the updates that are provided are so important, that HP provides them, why wouldn't accept all? Why I be offered the option to install or not to install? I do not understand almost all of them say. So, how to make a guess, one way or another? Should I just install all the updates? It would be the safer plan for someone, like me, who is a little computer illiterate?                          Thank you

  Hello

  It can be confusing when you see a list of the updates that were often less-than-useful descriptions.  A good rule is to allow all Microsoft updates as these will often focus on issues of security with the operating system.  The updates you mention in your post that are offered by HP, I would consider it.

  1. you have a problem with your PC that is mentioned in the updates are available.  Forinstance, if you scan a document or image, you are able to find the file.  If you can't find the file, it would be a good idea to apply update no. 3, but if you have no problem to find the file, there is really no need.

  2. the second update is a driver for your Modem PCI.  Once again, if this device works Ok (or like me, you do not use) there is really no need to apply the update.  This also applies to the first update, you mention - if you have never had the 'Installation cancelled' error you need to apply the patch.  If it arise in the future, you can always apply the update then.

  Updates BIOS will always have tem "Bios" in the description and code no.. as F14 or F32A also in the description.

  If you are ever in case of doubt, you can always ask your question on this forum and there are a lot of people here who will be able to advise you.

  I hope this helps.

  All the best,

  DP - K

• Windows 7 - error Code: 80000004 (cannot install updates)

  Up to this point, I never had problems with Windows Update, but over the last week have not constantly of my updates. At the beginning, I had about ten or fifteen years updates that all has failed. All but two, updates failed with Code 800F0826, including a search on the internet mention secondary code, which indicates that the update failed, but another update with a different code was at the origin of the problem. So I tried to run all the updates with the code 800F0826, he crossed without incident.

  
  

  The other two updates failed with Code 80000004, which I can't find a single move on, through the help on Windows Update or through internet research.

  The two specific updates that fail have done so consistently for several days, if I try to install alone or together, manually, or through the automatic update settings, that I put in place.

  Two updates that fail are as follows:

  Update security for Windows 7 for x 64-based systems (KB2378111)

  Error details: Code 80000004

  Installation status: failed

  Update type: Important

  A security issue has been identified that could allow an unauthenticated remote attacker to compromise your system and take control. You can protect your system by installing this update from Microsoft. After you install this update, you may have to restart your system.

  More information: http://go.microsoft.com/fwlink/?LinkId=201098

  and on the other hand

  Update for Windows 7 for x 64-based systems (KB2345886)

  Installation status: failed

  Error details: Code 80000004

  Update type: Important

  Install this update to help strengthen authentication information in specific scenarios. After you install this item, you may have to restart your computer.

  More information: http://go.microsoft.com/fwlink/?LinkId=202472

  The second update seems not be necessary, but the first seems important enough.

  Any person who can provide assistance would be much appreciated. For what it's worth, I am quite computer literate; I've been building and now my own systems and a few small servers for many years. I'm just at a loss when I get an error like this, and I can't find documentation on the error online code.

  Start a support ticket

  http://support.Microsoft.com/common/international.aspx?rdpath=1&Gprid=9860>

  See the section "How to get help" of http://support.microsoft.com/kb/2378111

  For individuals, please visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy.  If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  For more information about how to contact your local Microsoft subsidiary for security update support issues, visit the International Support Web site:http://support.microsoft.com/common/international.aspx

  For enterprise customers, support for security updates is available through your usual support contacts.

• A no Windows Update has shown as successful

  I tried to install:

  KB 890830 (Windows malicious removal tool) and
  Ko 905866 (Windows spam filter)

  Today, by using Windows Update.  After having waited 20 minutes and seeing always 0% complete on the installation process on the first KB, I clicked on 'Stop install', and then Windows Update immediately proceeded to the second update (KB 905866) and completed.  No error occurred.

  When I open Windows Update again and went to "update history", I see that both of these KB have been applied, but when I opened the "installed updates", I've seen the other installed.  I clicked on search for updates, but the first KB (890830) don't always appear as available updates.

  I don't know if it has something to with a recent system restore I did.  Yesterday I restored my system to 11 July, the restore completed successfully, but I realized my MSE definitions are completely returned to 28 June (date where I applied a number of Windows updates), and when I tried to shut down windows, it took considerably more time to close.

  Looks like my Windows Update history I messed up.  What should I do?

  I am running Vista SP2.  Thank you very much.

  Very general, do not think that the restoration of the system as a utility 'Save my ass', please. It's more a utility "well, I tried everything, then...". ».

  When you reinstalled Windows, the free McAfee trial has been reinstalled, too. You should have uninstalled then downloaded and free trial / run theMcAfee Consumer products removal tool before installing MSE. (No, it does not matter that you don't use or activate it.)

  The fact that you have so would explain well MSE freezing and the eccentric behavior Windows Mail & Windows Update. Follow these steps:

  1. Uninstall (McAfee) Site Advisor and whatever it is named "McAfee" listed in programs and features (seehttp://windows.microsoft.com/en-us/windows-vista/Uninstall-or-change-a-program).

  2. download the Tool McAfee Consumer Product Removal, save it to your desktop.

  3. close all open applications (that is, anything with an icon on the taskbar).

  4. click right on the file you saved in #2 above and select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then restart.

  5. for good bass, open the following in IE & run the difficulty: http://support.microsoft.com/kb/923737

  6. also, for good measure, open this article in Internet Explorer & run it in DEFAULT and AGGRESSIVE mode difficulty: http://support.microsoft.com/kb/971058

  7. restart & test.

  PS: The MRT downloaded & ran end. no need to do anything else.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Windows 7 - Office updates fail after reboot

  I am running Windows 7 32 bit, and last night I downloaded Microsoft Office 2010 and installed (upgrade of my edition of 2007 in the process).

  By the time I wanted to shut down the computer that he reported that 6 updates have been downloaded and must be installed. I have not read what they were, I guess I can some how?

  In any case, let him off and made the updates and off. Then I restarted the computer and it came with the second update screen that shows the percentage complete. At this point, I have to wait for what feels like 5 minutes (with remaining to 0%) and subsequently, that it says update failed and there back the changes. No error number is displayed.

  After logging in I tried shutdown again and he followed the same process. I have not tried this morning yet. How can I solve this problem?

  Thank you for your help. I was more happy with Windows 7, and until last night I didn't update window problems.

  Andrew

  Hello

  Thank you for your suggestions. I just wanted you to know that the second day updates seem to work without any problem. Then things seemed to unravel.

  Andrew

• Error codes with two updates to Windows Vista.

  The first update will fail poster KB929777 error code and when you right click the update, it displays error detail code 8000FFFF. The second update fails poster KB975929 error code and when you right click on the update it shows the detail 80242006 error code. I tried Mr. Fixit for these codes and it says that it failed. I tried manually and it has not yet. I have a 32-bit system with 4 GB of Ram. The system is a Dell XPS M1530. I had to reformat my hard drive today and these are the only two updates that failed to run.

  Error 8000FFFF when you download updates using Windows Update or Microsoft Update:

  http://support.Microsoft.com/kb/946414

  0 x 80242006 SUS_E_UH_INVALIDMETADATA the caller passed an invalid metadata update manager

  I * think * that means a file system cannot be found by the component maintenance base [CBS]. We can watch the cbs.log newspaper in WINDOWS\logs\CBS, and * hopefully *, know what file system is the culprit.

  Be aware that this newspaper can be very large.

  Start at the * bottom * journal cbs.log and do a find for the error.

  When the log will open in Notepad, scroll all the way down, click on edit, find

  Enter the error in find it what: line

  Under Direction: Put a check mark next to the top

  Then click Search

  This is an error from a cbs.log which shows the Windows Calendar as the 'not found ': file

  2007-09-05 03:16:55, error CSI

  [email protected]/9/4:17:16:55.326 (F) CMIADAPTER: failed. HRESULT =

  HRESULT_FROM_WIN32 (ERROR_FILE_NOT_FOUND)

  Element:

  [94].

  "name ="WindowsCalendarTasksACL"/ >".

  [gle = 0 x 80004005]

  2007-09-05 03:16:55, error CSI

  [email protected]/9/4:17:16:55.326 (F) CMIADAPTER: output with HRESULT code

  = (ERROR_FILE_NOT_FOUND) HRESULT_FROM_WIN32.

  [gle = 0 x 80004005]

  The file was actually on the system, BUT its scheduled tasks folder had been deleted. The 'package' could not find that file and the installation would fail.

  The post returns with the section of the cbs.log that contains the xml entry, as the section above:

  > Element:

  > [94]""

  Come back later, however. I'm sure someone who knows much more I do on this will be passing through any time now.

• HP Pavilion dm4-1265dx: does not update HP Pavilion dm4-1265dx

  Pavilion dm4-1265dx has never successfully updated its software. I run the recommended updates that are included in my automatic Windows updates, but not the HP updates have already updated, it always says, "failed." I tried to update directly from the HP site and have experienced the same results. Any suggestions?

  Hello

  Thanks for posting your concern for the Forums for Support and sorry about the problem you are having. To help you the best I would need the failure error code. I will quote the steps to get the code of failure below.

  • Go to the Control Panel
  • Make sure that in the upper right corner of the ' view by ' is selected for both small or large icons instead of the category.
  • Go to "Windows update".
  • You will find on the left in the list 'view update history'.
  • In the list, the status of the various updates would b mentioned in the second column.
  • There will be updates failed, you need to right-click on it and click 'see details'.
  • On the next window, there will be "Error Details" section with code 8xxxxxxxx.

   

  These are the codes that are required. Please write us back with these codes. And also for resolved errors you can try to install the updates individually.

  • You have to go back to the control panel > windows updates.
  • In the list on the left choose "check for updates".
  • Once the updates is enabled, it will be little important and a few optional updates.
  • First click on the important updates and a list would be populated, choose the updates one by one.
  • After an update is installed and the le redemarrage reboot the PC, choose the second update and continue in the same manner.

  Although I work for HP, but I am personally.

  Please click "Accept as Solution" If you feel my post solved your problem, it will help others find the solution. Click on the 'Bravo Thumbs Up' on the left to say 'Thank you' for helping!

  Concerning

  Aks3621