Sending sms using labview

Hello!!

It comes to my school project. I need to implement the design to send sms using labview. And I use iTegno 3000 modem and I have no idea where to start. Can someone has a basic idea for me? All the specific commands to use for the modem I use?

Thank you very much for your help

Good day! looking forward to all your kind reply...

Your sequence of structures aren't absolutely necessary and are just getting in the way so delete.

You do not have a phone number - the yyyyyy is not all correct and you do not send a CTRL-z character. You send the text "ctrl + z". Set the string to display hexadecimal constant and enter 1.

Tags: NI Software

Similar Questions

  • receiving sms using labview

    Hello

    You have an idea on how to receive SMS using labVIEW? I tried the AT commands using hyperterminal to receive the SMS, but I do not know how to continue on labVIEW to receive?

    The concept is same with the sending of SMS in labVIEW?

    Thank you

    Hi MiBL,

    If you could do this using AT commands, it is the same in LabVIEW so. Use the VISA, write the commands using the functions of writing to the modem and play the same thing using reading orders. You can even find examples for this if you search the forum properly.

    Kind regards
    Amine31

    (Bravo to give good answers, mark it as a Solution If your problem is resolved)

  • you want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. A

    I want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. After that, I want to arduino to send out necessary via a serial port to labVIEW which should be read using visa read and store in a chain. While I am able to write or read both individually, I can't do it consecutively. I used advanced read and write vi for checking my code, but nothing is helping. The wrong bed 'time delay before execution. " Please let me know where I can go wrong. Also is it possible to write code for hx711 using labVIEW

    1. you need not "\n" on your orders println().  This command adds an end of line character already in the message.

    2. you get the error because you have a loop around your reading.  After the first reading (well technically, the second because of you add an extra line end character), there is nothing left in the port.  As a result, you will get the timeout.

    3. you should really consider using a Structure of the event.  This way you just don't write and read when you press the Write button and you can also use the structure of the event to make the loop to stop.  I also go up to close the port inside the stop-> value Change event.

  • want to send sms using java

    I'm developing a stand-alone Java application that contains sms sending to certain numbers.

    I want to send sms using java and my phone connected to my pc with a usb cable (and not via Bluetooth).

    I use Linux operating system (Arch linux).

    I tried a few libraries that uses the sms online portals, but for some reason, I don't want to pay these sites. (just to make my card SIM cause its economic want).

    Help appreciated

    880667 wrote:
    I'm developing a stand-alone Java application that contains sms sending to certain numbers.

    I want to send sms using java and my phone connected to my pc with a usb cable (and not via Bluetooth).

    I use Linux operating system (Arch linux).

    I tried a few libraries that uses the sms online portals, but for some reason, I don't want to pay these sites. (just to make my card SIM cause its economic want).

    Help appreciatede

    The first thing you need to check: are you able to access other services my connection your phone by USB to the computer (line GPRS, calling). Because it requires the call or SMS access to the port. And you said that it is economic by sending an SMS using mobile, that depends. But most of the time, it is best to use the SMS service provider getway. They provide details http or FTP, there just put or message in the form accepitng, things happen by providing it service.

  • Problems sending SMS using SMSTransport

    I am trying to send an SMS using SMSTransport, but I get the following result when my application tries to send a message:

    TMTP::setupFdListener
    TMTP::handleConnected - Connected to ChatService
    New Session Request
    Open Success:
    Session Details "https://discoveryservice.blackberry.com/discoveryPoxmlServlet/" "1.0" "127.0.0.1" 8888
    creation of local SMS-MMS account succeeded
    Created instance of PIMCoreStatusManager
    PIMCoreStatusManager Constructor
    Calling AccountServicePrivate::defaultAccount for service type= "messages"
    Setting Curl Global Init 0
    GET 0x1
    URL Buffer: http://127.0.0.1:8888/accounts/default/messages 
    
    Curl Easy perform
    Curl Easy GetInfo response code
    Curl easy getInfo content_length_download
    Curl Error Code 0
    Response Code 200
    Get Contacts: (QVariant(int, 4) ) 
    
    PIMCoreAccessPool::getPca 0 Thread Id 0x1
    PIMCoreAccessPool::getPca a new PimAccess 0
    getContactDtails called 4
    GET 0x1
    URL Buffer: http://127.0.0.1:8888/contact/4/4 
    
    Curl Easy perform
    Curl Easy GetInfo response code
    Curl easy getInfo content_length_download
    Curl Error Code 0
    Response Code 200
    TMTP::send origPort 0 destPort 0
    TMTP::send attachments 0
    TMTP::send invalid attachment
    

    Here is the code I use to send the message:

    void AlertUtilities::sendSMSMessage(QString subject, QString body)
    {
        SmsTransport smsTransport;
        AccountService accountService;
        ContactService contactService;
        Account account = accountService.defaultAccount(Service::Messages);
        MessageBuilder* messageBuilder = MessageBuilder::create(account.id());
    
        QList contactIds = settings->getSelectedContacts();
    
        for (int i = 0; i < contactIds.length(); i++)
        {
            Contact contact = contactService.contactDetails(
                    contactIds.at(i).toInt());
    
            if (contact.phoneNumbers().length() > 0)
            {
                MessageContact messageContact = MessageContact(i + 1,
                        MessageContact::To, contact.displayName(),
                        contact.phoneNumbers().at(0).value());
                messageBuilder->addRecipient(messageContact);
            }
        }
    
        Message newMessage = messageBuilder->body(MessageBody::PlainText,
                QByteArray("This is a test"));
    
            smsTransport.send(0, newMessage);
    }
    

    Can someone help me understand what I'm doing wrong here?  There seems to be no documentation or examples on how to do it properly.

    Looks like I've got a code snippet rather autonomous and complete handy for this one as well.  (I think you can find others scattered around these forums as well.)  Here it is:

    void sendSms(const QString &messageText, const QStringList &phoneNumbers) {
        bb::pim::account::AccountService accountService;
        QList accountList =
            accountService.accounts(bb::pim::account::Service::Messages, "sms-mms");
    
        bb::pim::account::AccountKey smsAccountId = 0;
        if(!accountList.isEmpty()) {
            smsAccountId = accountList.first().id();
            qDebug() << "SMS-MMS account ID:" << smsAccountId;
        }
        else {
            qWarning() << "Could not find SMS account";
            return;
        }
    
        bb::pim::message::MessageService messageService;
    
        QList participants;
        foreach(const QString &phoneNumber, phoneNumbers) {
            bb::pim::message::MessageContact recipient = bb::pim::message::MessageContact(
                -1, bb::pim::message::MessageContact::To,
                phoneNumber, phoneNumber);
            participants.append(recipient);
        }
    
        bb::pim::message::ConversationBuilder *conversationBuilder =
            bb::pim::message::ConversationBuilder::create();
        conversationBuilder->accountId(smsAccountId);
        conversationBuilder->participants(participants);
    
        bb::pim::message::Conversation conversation = *conversationBuilder;
        bb::pim::message::ConversationKey conversationId = messageService.save(smsAccountId, conversation);
    
        bb::pim::message::MessageBuilder *builder =
            bb::pim::message::MessageBuilder::create(smsAccountId);
        builder->conversationId(conversationId);
    
        builder->addAttachment(bb::pim::message::Attachment("text/plain", "", messageText.toUtf8()));
    
        foreach(const bb::pim::message::MessageContact recipient, participants) {
            builder->addRecipient(recipient);
        }
    
        bb::pim::message::Message message = *builder;
    
        messageService.send(smsAccountId, message);
    
        delete builder;
        delete conversationBuilder;
    
  • Send SMS using Oracle database automatically

    Hi all:

    I want to send SMS from Oracle 9i automatically database. What reg software. can I use?

    Hello

    Here's the Oracle Forms forum.
    You would have more chance of getting the answers by posting in the forum database ; D

    François

  • sending sms using java

    Hi all! I do a web application project in j2ee because I need to put the sms Setup by using the java program and I have no idea about it so I kindly ask you help me on this...
    Thank you
    Vinoth...

    a friend this is not the forum for this :)... newways you need a way to portal sms for texting... do you have material hv supported

  • Sending SMS: is it possible to add an entry from sent SMS/trash

    Hi all

    I am able to send SMS using MessageConnection/DatagramConnection, but is it possible to add them to the sent SMS/trash on device?

    According to the api folder of my knowledge only with e-mail Messages.

    Thanks in advance.

    There is no API to access the sms folders

  • I am new to the ethernet communication using labview. I don't have any material. I have two laptop, I need to send and receive data through these 2 portable by using labview. Kindly help me on this.

    I am new to the ethernet communication using labview. I don't have any material. I have two laptop, I need to send and receive data through these 2 portable by using labview. Kindly help me on this.

    Dennis has already said: for a direct PC - PC connection, you need a cross over cable. If you connect through a router or a switch, you use a standard cable.

  • Send and receive SMS using JDE and WMA JSR120

    Hello
    I've written a midlet that send and receive TEXT messages.
    This midlet works well using Sun WTK, I can send SMS of midlet and receive...

    How can I send and receive SMS using BB JDE?

    Help, please
    Thank you!

    Take a look at this thread:

    http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=java_dev&message.ID=15778&query.ID=19...

  • iOS 10 no longer allows you to choose to send SMS

    Hi, I have upgraded to iOS 10 and I don't have the option key on an iMessage that invites the option to send SMS. I regularly use this function when I travel or am in areas without large internet service. I know I can disable iMessage but which is rather annoying. Is there a setting that I'm not aware? I plan on downgrading to iOS 9 if not.

    Have you checked the phone settings? Settings > Messages > Send as SMS > on.

  • Cannot send SMS

    I have a Apple Watch watch OS 2.2.2 (13V604) running and one 5 iPhone with iOS 9.3.5 (G 13, 36). Previously, I found that the watch would not send SMS free hands unless I turned on iMessage; These messages would simply disappear, but things seemed to work for a few weeks after iMessage has been activated.

    Now, I find that the following will happen if I try to send messages to someone who doesn't use iMessage (e.g., Android users):

    'Hey Siri, send a message to $PERSON saying $MESSAGE'-> in a few seconds, a notification indicating that the message is not sent. The message does not appear in the mail app on the iPhone, but I know that many have unsent messages in the message shows application (it seems impossible to return or reject these). If I select a message manually via the mail app on the watch (whether by you answer or make a new) then it is sent correctly.

    Unfortunately, the sending of text messages hands-free for Android users is very high on the list of the essential requirements for the use of this watch. Can anyone suggest how to deal with this? NB. I already turned iMessage market again and power cycled shows and the iPhone.

    Hello

    It can help to switch send as SMS works again:

    -On your iPhone, in settings > Messages > Send as SMS.

  • iPhone refuses to send SMS to people who have enabled iMessage

    I can send text messages to people who have not enabled iMessage, but my iPhone refuses to send an SMS to people who have enabled iMessage, even if I disable iMessage on my iPhone.

    Koenraad De Smedt wrote:

    I can send text messages to people who have not enabled iMessage, but my iPhone refuses to send an SMS to people who have enabled iMessage, even if I disable iMessage on my iPhone.

    Are these people that you send using iPhones or iPad?  iMessage is Apple free internet e-mail service and works in Apple devices, but not just iPhones. If someone has an iPad only and uses an iMessage account on the iPad, then they can't get SMS text (unless they pair the iPad with an iPhone).  iPads cannot natively receive or send SMS texts.

  • Cannot send SMS to users no iMessage!

    This is probably my fourth post on this same issue that nobody is to give me an answer, or telling me to try something that I said did not work.

    I have an iPhone 6s with MetroPCS, for someone who is not using iMessage, the 'Add photos' icon is grayed out and it won't let me even to send an attachment. Before the last update, I was able to select the "Add attachments" button, but it is still impossible to send to the other person. I can't receive messages from group to anyone, unless they are all using iMessage, also to receive photos of users who are also no iMessage. iMessage is turned on, and I tried it works and stop. SMS is selected. I tried to take the sim card out, turning the phone, return, and reinsert the sim card and which worked for only 5 minutes, before aging again on the attachment button Add. WiFi and cellular data are both on, the two won't let me send an attachment. I reset the network settings, I did a hard reset on my phone. I did a reset based on my phone, I know that's not a problem of the carrier because it allows to work, until after I did an update in November 2015. Since then, she has been less effective. Please someone help me.

    Hi keakuki,

    I understand that you have difficulties to send SMS and MMS messages or receive group messages since you last updated your iPhone.   Your profile says you are using iOS 9.3.  You have updated to the latest version, which is iOS 9.3.1?  Once you have done this, the next step would be to see if MetroPCS has updated their software. given that the SMS and MMS messages must go through their system.

    If you can't send or receive messages on your iPhone, iPad or iPod touch

    Restart your device and check for updates

    1. Restart your device.
    2. Looking for a carrier settings update.
    3. Looking for an updated software iOS.
    1. Make sure that you are connected to the Internet through cellular data or Wi-Fi.
    2. Go to settings > Messages. Check that the type of message you are trying to send is lit (iMessage, SMS, MMS or e-mail group):

    If your messages are not sent or you do not receive the messages

    Check your details:

    1. Make sure you use the right phone number or email address of the contact.
    2. Go to settings > Messages > blocked and make sure that the contact is not on your list of blocking.

    If messages will not send to a certain person or you need assistance with group messages

    Sometimes it will not send your messages to a particular contact, or you might have problems with Group Messaging. For example, you could meet a group conversation and receive your own message. Or you could get a new phone number and see your old listed as a recipient in an existing group conversation.

    Delete the conversation * who has the problem and start a new conversation:

    1. Open your Messages and view your list of conversations.
    2. Straight shot left on the conversation you want to delete. Then, remove faucet.
    3. Open your Messages, type and enter the phone number or email address of your contact or contacts.
    4. Write a new message and press send.

    * When you delete a conversation, you will not be able to recover. If you want to save parts of conversations or their attachments, you can take screenshots. You can also tap a bubble attachment or message, and then tap more > save.

    Take care

  • Can I send sms with Skype overview?

    I saw Skype on my windows 10... but is it possible to send SMS with Skype preview because they said it's free... but I can't?

    Not at the moment, but let me clarify that:

    Before the update birthday you could send both SMS and Skype IM Messenger + Skype app, it stopped, and I think as functionality of it will go to Skype (we assume the application overview, but it may not be called that forever).

    You can of course always send SMS from your PC using Cortana sends using your phones SMS service.

    You can send SMS via Skype, but it currently costs money, so you need Skype credit or a subscription that included text Messages (not seen one of those).

Maybe you are looking for

  • I can't update my 5 c to 9.3

    Im still getting this message everytine I tried to check the updates. 9.3

  • Library of photos after the beta

    I used the beta version of El Capitan, and today I've downgraded to usual El Capitan. The problem is that I can't use pictures. Only, it does not support my library and I can't use it. I tried to recover, but 95% it says error. So, what can I do? Y a

  • J2C89PA #AB4: Intel Dual Band Wireless-AC 3160 bluetooth problem

    I installed my adapter wireless laptop 'Broadcom BCM43142"to"Intel Dual Band Wireless-AC 3160 ac 802.11"later confirmed that the new card is supported for repair.  The two latest drivers for Intel wireless and bluetooth are installed (18.33.0.2 and 1

  • Virtual memory in Windows

    Sorry I typed in detail in the area of title darn it. I don't know if someone will be able to read about my problem. If this isn't the case, I can refer the question. Here is the thumbnail version, says pop up windows needs more space for virtual win

  • Error at startup, insert BPD Software

    I get a box every time I start up it says the feature you are trying to use is is on a CD-Rom or other removable disk that is not available Insert disk BPDSoftware and click OK Don't know what it is help please do disappear, it will not leave.