Separate byte-by-byte series chain

Hello

This is my first post and only started using labview yesterday please sorry if it sounds a bit stupid. I connected an arduino via labview and sent data that him and had given returned. I can get it to draw a waveform of these data a chart. However I do the arduino send data from sensor by iteration. I have 8 sensors each byte that comes through for a new sensor data will be, after the eighth sensor sensor will begin a new and repeat the process. I have need to separate this data and put it into eight different tables, but don't know how to do it correctly.

Any help is greatly appreciated.

Thank you

Hi Canalian,

convert your string of VISARead into a table of U8 and decimate this table in 8 sub-tables:

Now you have each separated data sensors in its own table and you can do with it what you want.

Well, you can also use StringSubset to obtain each byte because it's clean...

Tags: NI Software

Similar Questions

  • Lack of bytes in the communication of VISA

    Hello

    I created two with labview programs that communicate with each other using virtual COM ports that are connected correctly.

    The first program sends a packet that contains an integer n to the second program that would return n packages containing 9 bytes, there is a pause between each two consecutive packets.

    When I set the baudrate to 500 or 700 for both programs and for n = 360, they are operating correctly and no byte is not respected.

    The problem is when I change baud rate to 1000 and more, for both programs and n is always equal to 360, there are a few separate bytes failed (between 0 and 3 bytes in general).

    So, what do you think is the source of the problem?

    May not be the size of the buffer because it is set to 64399599 (no kidding, this is the maximum size). Besides, I used both programs to other purposes where one received the second 1000 * 9 bytes for n times (there is a period of pause between two consecutive of 9000 bytes is sent).

    On the other hand, I checked what the second program sends looking out back County of the entry VISA and trying to send these packets to hyperTerminal. And there is no packet lost (even for a 9600 baud rate).

    So I guess that the problem is in the reading part.

    If someone could help me I would be very grateful.

    I tried with semaphores, and it is not working properly, thanks crossrulz!

  • Buffer problem and cases of ring series

    Hi all

    I had an interesting problem and have a moment that is difficult to find a solution and thought a pair of fresh eyes can help!  I read data during the series using VISA.  That's going well.  I do this continuously and then adding in a string.  This string, I look for new lines and pull them out of the buffer series chain.  I have then look at the lines to see if they have the appropriate orders and, if so, analyze these commands to control a box structure.

    Now, here's the interesting part.  When I started, I wrote a vi to take in an arbitrary multiline string in and analyze data and sentences, and it works as expected, but when I do it with serial data direct and the ring, the case statement buffer does not.  Also, when I probe the parsed string that will control the case statement, it LOOKS right, but the case statement will not accept it.

    Any thoughts would be greatly appreciated, I'm quite confused as to what is happening here.  I have attached the 2 vi.

    Gurus?  Masters?

    Thank you!

    Jim S,.

    I see a few problems.  As previously validated you should use greater or equal? instead of superior?.  The biggest problem is that you have a string constant value '\n', but the constant itself is not configured for '-' code display mode.

  • 2 ways to send 16-bit to the serial port. What is the good?

    I am trying to send data via a serial port... This data consists of a 16-bit format. The data are sent by a DSP. Searching in the internet I found two ways to send data. The first is that the first photo anda the second way is the second picture.  I read data ok, which in this case is a sine wave. But I 'don't know if it is correct or not.

    In the first case , the citation read buffer sende th 8-bit to decimate them VI that will be concatenated after to join numbers function...

    Is it fair or not?   Second question. I noticed when I put multiples of 8 in the number of bytes the graph is ok. But when the number is not a multiple is the graph 'missing pieces '.  Why?

    In the second case, I confess I didn't undertood it. I know that the CASTING of TYPE function transforms the string on a table swap bytes (DSP sends the MSB and LSB) I know what subset of string.  I read that the 4 in the offset is put there to avoid the reading of the data header. But I don't know why 2048 is here. The latter reads data too...

    With any who answer my questions would be a really really help

    Thank you guys.

    First case

    second case

    Both are probably correct for the data being sent.

    If you want to read a unique 16-bit value at a time, then obviously you would set the number of bytes to read to be 2. The following code shows two ways to convert the two bytes to a single value. The chain Unflatten to specify the boutien.

    You don't mention her, but how do you synchronize the data. With the dsp to send two separate bytes, not sure what byte you will read first. Do you send start/stop characters so that you know this vital information?

  • Digital binary conversion!

    Hello

    I want to capture the string in array of 22 bytes to write VISA to an instrument of control. I want each byte in not more than 8 bits and bytes in the table are the binary 8 bits of some decimal binary conversion. for example. Machining time is 180 000 milliseconds that converts binary in 3 sets of 8 bytes. I want to do 3 bits separate (high, medium and low), out of it. Conversion of the maximum value I get is 8 bits, which is 255. How to divide numbers greater than 255 to separate bytes of 8 bits for a single decimal value?

    Thank you.

    Well, if you have 24 bits, you must go up to the next larger data type.  In this case, it would be a U32.  You can use the slot number, then build a table to make sure that the bytes go where you want to.  This is assuming you are using LabVIEW.

  • TV shows, appearing in the wrong order

    I run all of my shows/movies from my mac to my apple tv via computers and home sharing app, since the update yesterday, all my tv series tv series numbers appear in the mess, they finally condense television programs if you do not have a separate line for each series, which is great, but my shows are appearing as season 4 6, 2, 3, 1, 7 etc.

    anyone else having this problem?

    I have exactly the same problem. I posted about it here: Tvos 9.2 Home Sharing - Tv Shows.

    I got no response. I don't know if it's an unexpected consequence of 9.2 or some other bug.

  • Firepower supported devices

    There are differences in supported features of firepower for the series 2 and 3 materials. Is there a clear vision of what devices are series 2 and 3 series which devices?

    Material series 2 are the oldest brand devices Sourcefire. They were all end of 2012 sales or more.

    They include the following models: 3D500, 3 D 1000, 3 D 2000, 3 2100, 3 D 2500, 3500 3, 3 4500, 6500 3.

    All other dedicated NGIPS devices can be considered as the 3 series.

    (Modules ASA power of fire and any new firepower 9300 and 4000 series is in a separate category and neither series 2 or 3).

  • The research of Web applications with fields of the Data Source that contains multiple values

    I have a Web application with a field that allows multiple values to be recorded similar to the list box. I need limit the allowed values for a large, over the list of the values currently stored in another Web application as a data source. I can not apply to the type of Data Source field that allows only single value selection. I also need to be able to use the search form Web App to search for items containing 1 OR more of the values in this field (a type of list control field search functionality). Here's what I tried to field types:

    • Text (String) or text (multi-line) field type - By saving a list of values separated by commas (outputs in the same way this list box) to an entry of text or textarea, the search only logic search exact string (including commas) and does not analyze individual values.
    • Type of list (checkbox) field - it allows me to search for multiple values using the logic of the GOLD, but the web application stores only the values that have been entered as an option in the field settings real web app. I tried to use a checkbox with minimal or empty options list, hoping that some values I sent more separate by a comma value chain would be still stored, but because the values come from my Web App data source and not stored with the field options list, they were not saved.

    Someone at - he found a way to do it?

    My other question is how can I use a multivalued field to similar as described above but return results containing the elements with ALL the values of this field (AND logic).

    Can someone enlighten me to the inner workings of the search BC logic web app?

    You don't need to use the predefined boxes or types of entries. Everything you can represent as a string (such as the values separated by commas in your example) can be saved in any field of webapp. The types of fields defined in the Web application are only used to translate internal representation (all channels) to the various user-friendly interpretations (checkboxes, radios, dates, links, etc.)

  • replacement of the same value in a string variable values

    If I have a string:

    "%s is %s that I'm talking about."

    and - I want to replace the instances with DIFFERENT values %s... What is the best way to do it.

    I thought of her analysis in separate using substr and instr chains, but I don't know if that's an exaggeration or not.

    Replace is ideal but - it replaces all occurrences of if - you can indicate just replace the first occurrence of a value, and the second with one another (i.e. If the result after replacement of the string above was supposed to be "it's the chain that I'm talking about"

    Any help is appreciated.

    Thank you

    Hello

    wtlshiers wrote:
    If I have a string:

    "%s is %s that I'm talking about."

    and - I want to replace the instances with DIFFERENT values %s... What is the best way to do it.

    Whenever you have any questions, please post CREATE TABLE and INSERT statements for some examples of data and the results desired from these data.
    Explain how you get these results from these data.
    Always say what version of Oracle you are using (for example, 11.2.0.3.0).
    See the FAQ forum {message identifier: = 9360002}

    I thought of her analysis in separate using substr and instr chains, but I don't know if that's an exaggeration or not.

    Depending on your needs, you may need to do this.

    Replace is ideal but - it replaces all occurrences of if - you can indicate just replace the first occurrence of a value, and the second with one another (i.e. If the result after replacement of the string above was supposed to be "it's the chain that I'm talking about"

    As you say, REPLACE replaces all occurrences. There is no way to say (for example) to change only the first.
    REGEXP_REPLACE, is much more flexible. There is no option for giving a specific occurrence, but you won't even have this feature. You want maybe just something like

    REGEXP_REPLACE ( '%s is the %s I am referring to'
                , '(.*)%s(.*)%s(.*)'
                , '\1This\2string\3'
                )
    

    Depends on your data and your needs.
    Are the new values (e.g. 'This' and 'chain') fixed, or if they can change from one line to the other?
    You will always have 2 (or certain known number) of ' %s in the original string?
    '%' Always report something that needs to be replaced? If not, how can you tell when he does and when it doesn't?
    Of ' always come right after "%"? If this is not the case, what are the possibilities, and what the different characters?

  • unique or constraint validation?

    I'm not a pl/sql programmer, can often sort code to make sense and have written simple stuff, so...

    I need to put in place a constraint on a field in a 'form with report.' Catalogs the user documents and there are number of iterations of the document numbers (ISO_NUMBER) according to the type (political, checklist, procedure: POL-xxxx, VS-xxxx, PRO - xx *. * xxxx, etc..) Each document has revisions, of which some are incremented by a certain number and others by letter POL - xx.xxxx Rev A, Rev B or VS-xxxx Rev 1, Rev 2, etc.). For these fields of revision, which are a separate area that the ISO_NUMBER and other unrelated areas who have no points, hyphens, or alphanumeric combination and need to auto-increment when a new form is sent, I set up calculations and processes to treat this increment automatically on submit (thanks to one of you guys several months ago!).

    How can I configure an error handler or constraint so that when it sends a new form but has duplicated the ISO_NUMBER, an alert will appear? If she creates a new revision, the ISO_NUMBER and the title of the document (DOC_TITLE) will not change. If she has reproduced the ISO_NUMBER inadvertently, the DOC_TITLE will be different.

    I have him asked to simply sort the report (and showed her how to save a report sort of that way) to display the most recent number created so she can simply enter the next, but... .well you know this story. So, if that's too much, and that I should put my foot down, tell me.

    Also, I can not change the numbering conventions - I addressed this issue several times I get the "this is the legacy." Well, "LEGACY" has been plagued with inconsistencies as you can imagine, more than six years I was employed here, so I will try to prevent the user as much as possible. I had the chance to separate the rev of the chain of document number, and then I cleaned up thousands of names of document files! :-)

    Request Express 4.0.0.00.46

    TIA,
    Alexandra

    Based on your pseudocode, a validation of type function returns BOOLEAN would be something like the following. Mind you I don't really understand why the document title and ISO number must match so that he can generate a warning, but not my concern...

    P # bind variable must obviously be replaced with the names of items in real pages.

    DECLARE
      v_count    NUMBER;
    BEGIN
      -- Only check ISO when not a revision
      IF NVL(:P#_REVNUMBER, 'IR') = 'IR' THEN
        -- See if any documents match this ISO # and doc title
        SELECT COUNT(*)
        INTO   v_count
        FROM   doc_info
        WHERE  doc_title  = :P#_DOC_TITLE
        AND    iso_number = :P#_ISO_NUMBER;
    
        IF v_count > 0 THEN
          RETURN TRUE;
        END IF;
      END IF;
      RETURN FALSE;
    END;
    
  • loading on a Web site

    I created a Captivate file and saved as a file in flash (800 x 600-6: 5), which then is uploded in a site. The preloader for me on the cable happens quite quickly, but the lilies take nearly 20 sec. I want to speed up the process.

    Is it possible to rather than create a single file, to separate it into several files chained, hopefully reduce the loading time?

    I don't know that this will answer your question or not, but...

    Our intranet is unable to manage the files are too big so I had to break one of my more 6 small projects linking via buttons in the module.

    For example, Section 1 was slides 1-15 were the properties of the button NEXT slide 15: success - open URL or file - then the file name in the URL below.

    Be careful with your (without spaces) naming conventions to ensure that links to the correct file. I have not tried with Captivate 2 yet but judging from what my file look like it works perfectly.

    Don't know if it's any help.

    Good luck
    Alex

  • control of chain to limit the number of bytes

    Hello

    Is it possible to set the limit on the length of the control of the chain in number of bytes? I have a control to the string whose length is always going to be 3 bytes and I don't want the user to enter accidentally more bytes.

    What I did just now, is having an event on the channel to change value and display only the 1st 3 bytes every time that happens the value change event, but I want to know if there is no direct way to set the limit on the number of bytes on the control of the chain.

    Thank you

    Ritesh

    This has been discussed several times in the past. For example, look here.

  • best method to transmit the PPM (servo control) in series-wireless transmitter? (how to combine binary + whole in a single series byte)

    I'm pulling my hair out here... I hope someone can help to guide me in the right direction.  I'm just learning binary and hex, so please forgive me (and correct me!) if I say something wrong.  I have to give credit when it is deserved, because I use info from a post on theautochannel.com to drive this development.

    I try to control a small indoor RC helicopter using LabVIEW and a USB joystick.  I communicate with a transmitter wireless via rs232 (TTL converted), the Protocol is 125000, 8n1. Each image is 14 bytes 2 bytes of header.  I would like to transmit data PPM (pulse position modulation) which is actually just a 10bits (1024 possible measures) range that dictates the position of the servo, for each channel.

    Byte 3 & 4 are channel 1, byte 5 and 6 are channels 2, 7 & 8 CH 3,... and so on until the bytes 13 & 14 which is CH 6.

    Each pair of bytes begins with "00" (binary).

    Byte 3 & 4 should look like "00 00 00 xx xx xx xx xx", where the first "00" is the header, then "00 00" is the identifier of the servo, and 'xx xx xx xx xx' represents the position of the servo. The identifier is actually integrated in the position of the servo, the bits serve a double purpose.

    That's why it all will look like this:

    CH 01:00 00 00 xx xx xx xx xx (position has a valid range from 0 - 1023)

    CH 02:00 00 01 xx xx xx xx xx (range 1024-2047)

    CH 03:00 00 10 xx xx xx xx xx (range 2048-3071)

    etc... If you convert the binary range, you can see how the second half of the bits ID servo are provided by the range of servo.

    I intend by entry VISA to send every byte to constitute the entire frame, and then I will pause ~ 10ms between frames. However, my question is how the hell should I code this? !!  I think I need to write, take 1 CH for example, bytes 3 and 4 together into a string and then split them back hand to be sent as two distinct bytes.  However, I do not know how to mix my header and the first two bits of my ID servo, which is binary '00 xx', with my servo position (which I know I can write in decimal form, as entry VISA will convert it in binary). Any thoughts on the best way to do so, given all this?

    An empty string character likens to a binary "0"?

    Has totally confused everyone?  I really hope not, but I'm pretty tired so let me know if I need to simplify my question.  I hope someone can enlighten me as to the best way to combine the binary constant w modification of decimals (or hex).  And if anyone has thoughts about a good way to organize my vi together, I understand that too!  Right now I'll just use the structures of sequence... I post my code but at the moment, there is not much to look at

    Thank you very much!!

    No, you do not confuse everyone, but I think you might have confused yourself.

    You basically need to do is to create the array of bytes that will be sent, and then use the array of bytes to a string, so you can send it to the serial port. The creation of the byte array can be done in several ways. You deal with 6 16-bit numbers, of which the lower 10 bits are the values of the position of the servo. I don't know what you want on the front panel to look like, but if you have 6 separate (one for each servo) controls with each set having a range of 0 to 1023 (for 10-bit), then you just have to OR each value based on the number of servo. Put all this in a table, add the bytes of the header and the array of bytes to a string allows to get a string that you can send via the serial port. You can also do this in a loop. Joined a VI to show the two concepts. You have not indicated what version of LabVIEW, is 8.2 you use.

  • Problems with reading the series bytes

    Hello

    I currently have a PIC18F microcontroller serial communication with LABview using the base read and write.vi series. The PEAK sends strings such as "V222! (V is the character of the header, and! being the end character). Then, I have a program to take each individual character read and concatenate them in a larger string for data extraction. The port has been configured to 38400 baud and be only a single byte of long.

    The captain sends this one byte at the time and the problem here is that LABview seems to be only reading V most of the time, and occasinally has 2. Since it doesn't seem to be never read the end character, the sequence of extracting data from my code is never executed.

    A few questions I have are:

    The captain may send one byte at a time, but also all other devices communicate through a serial port.  The definition of the serial port involves both a byte.  Actually it's really a LITTLE at a time.  But serial port parameters leads to the gathering of 7 or 8 bits to produce a byte.  The PEAK sends a follow-up byte to another byte, etc.  The time between shipments of the byte may be too small to read contiguously in your Labview program.

    At very slow speeds, it could really work.  At 300 baud (3mS / bit), there are 33 mS to send a byte (8-bit + stop bit, start bit).  So if your loop runs fast enough, you get every byte one at a time.  But there is the overhead of other code to store the bytes, etc..

    38000 baud to only 0.2 mS to send a byte.  LabVIEW is not fast enough to loop at this rate to capture all the bytes individually.

    But why bother?  Simply capture all the bytes and treat them as a complete message.

  • How to stop the series 'VISA read' the sends packets instead of bytes available.

    Dear Labvillians,

    Highlights:

    How can I stop series "VISA read" send me packages rather bytes?

    Background:

    I have a system which publishes series of 14 bytes on a semi-regular interval packets.

    At busy times, the producer of these these queues of data packets, effectively producing Super-paquets multiple of 14 times larger than 8 packages (112 bytes) bytes.

    My protocol handler is designed to process bytes, packets, or packets Super.

    Now, my request has multiple devices and the order of message processing is essential to the proper functioning.

    My observation is that read VISA waits until the end of a package / super package before moving the data to the application code. (See chart below)

    My expectation is that VISA read should give me bytes available, get too smart for itself and not wait for a package.

    .

    I noticed this on PXI, PC shipped, PSC and, more recently, cRIO

    I've experimented with Scan interface the cRIO rate, which helps to reduce the backlog of packages but don't decide to package under read byte.

    I understand that a solution is FPGA code write to handle and pass the bytes by R/T-FIFO, and there are some great examples on this site.

    Unfortunately, it does not help with FPGA devices not.

    I have also dabbled in the event based sequential reads, but he is evil on vxWorks devices.

    Any help is appreciated

    It is helpful to sometimes talk to yourself.

    I hope that is useful for someone sprinkle in the future

Maybe you are looking for

  • Unable to connect to apple in new iPhone 6 s ID

    I saw recently a problem with the new iphone can't connect to itunes 6 s means it strucks on initial configuration page itself. I tried via wifi and 4 G cellular network. But always without success. Any idea?

  • How can I fix the firefox search engine?

    When I put something in the search engine and press enter or the search button, it does nothing no matter how many times I press on enter or search button.

  • Compatible product HD for HP Pavillion P6754Y

    More than 6 months ago I started getting the dreaded 'hard drive failure is imminent. Yes, I took all the precautions. Last night he died (to a certain extent, I was still able to make a final backup). My question is... now that I'll have to replace

  • Foxfire.exe no disc? error

    When I try to implement my foxfire browser I get a message saying foxfire.exe - no disc, there is no disc in the drive, insert a floppy in G? Why is I get this every time? If someone on my computer moved something they shouldn't?

  • Decommissioning of windows on HP sleekbook 15-b009ee 06:52

    Hello I need your help. I have a HP sleekbook 15 - b009ee which was pre installed with windows 8. I want this downgrade to windows 7 because windows 8 is a disaster for me! I'm ready to give up with my laptop. Please guide me on how to install window