Service Pack does not have changes to restore it then shuts off and restarts with the same message over and over again.

Help!  I have an apple mac with windows alongside mac system.  I the have not used for a while and when I logged in the windows system advised me to update to IE 9.  To do this, I had to install Service Pack 2 I did.  He then restarted but cannot install and came up with the following: Service Pack does not have changes to restore it then shuts off and restarts with the same message over and over again.  I don't know what to do to reopen and to reinstall the Service Pack.

Hello

This article explains how to troubleshoot problems when you install a service pack for Windows Vista or Windows Server 2008.

http://support.Microsoft.com/kb/947366

Use this forum link for all questions related to Windows Vista SP1, Windows Vista SP2 and Windows Server 2008 SP2 below.

http://social.technet.Microsoft.com/forums/en/itprovistasp/threads

or repost in the Windows Update forum link below

http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all

Tags: Windows

Similar Questions

  • I have a p6210f (Win 7), that does not illuminate. As recommended, I tried a new power supply with the same results.

    In my post in November, I explained that I had tested the power supply with a multimeter and read the correct voltage. Two people to the Board of Directors always seem to think it was the power supply, so I replaced it with a new one (Corsair CX 430 R) and it still won't turn. I had suspected the power switch because when I bypass the MOBO 20 pin plug 'on', the power led lights up, fans have come on short and I heard the rotation of the disk. I also tried to troubleshoot the switch by jumpering the pins on the motherboard, but still no luck. Someone there ideas more before I replace the card MOTHER and CPU? Thanks in advance.

    Roamstead

    Cloud_strider,

    Thanks for the reply. After swapping the PSU, CPU, taking the RAM pins on jumping on the MOBO for power/LED/reset button, each separately and with the same result, I eventually swapped the MOBO to an ASRock A785GM - THE and who did! He finally put under tension. Thanks again.

    roamstead

  • "service pack do not have. recovery of Exchange"has been ongoing for more than 12 hours. Have turned off on the reboot, but the message remains. How can I fix?

    I installed the service pack and when the computer restarted message "service pack do not have. restoration of the changes. "came and slept there. I tried to turn off computer and start in safe mode, but nothing helped. Has been ongoing for more than 12 hours and no change. Any ideas? Thank you

    Hello

    You can try this:

    the link below is how to download and get a vista disk startup repair, which you can start from the

    http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

    Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

    http://www.bleepingcomputer.com/tutorials/tutorial148.html

    to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

    It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

    Change boot order it do dvd drive 1st in the boot order

    http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  • What is wrong with this sequence, it does not work when, after 3 inserts, I add a new record with the trigger it gives an error.

    Mr President.

    What is wrong with this sequence, it does not work when, after 3 inserts, I add a new record with the trigger it gives an error.

    --SL_CUSTOMERS table data
    
    
    INSERT INTO SL_CUSTOMERS VALUES(1,'Kamrul Hasan',NULL,NULL,'Moghbazar', 'Dhaka','0456789123',NULL,NULL,NULL,'Y',NULL);
    INSERT INTO SL_CUSTOMERS VALUES(2,'Rabiul Alam',NULL,NULL,'Motijheel', 'Dhaka','0567891234',NULL,NULL,NULL,'Y',NULL);
    INSERT INTO SL_CUSTOMERS VALUES(3,'Shahed Hasan',NULL,NULL,'2-G/1,2-2,Mirpur', 'Dhaka','0678912345',NULL,NULL,NULL,'Y',NULL);
    
    
    
    

    CREATE SEQUENCE  "ALIZA"."SL_CUSTOMERS_SEQ"  MINVALUE 1 MAXVALUE 9999999999999999999999999999 INCREMENT BY 1 START WITH 1 NOCACHE NOORDER  NOCYCLE ;
    
    
    CREATE OR REPLACE TRIGGER SL_CUSTOMERS_TRG 
    BEFORE INSERT ON "ALIZA"."SL_CUSTOMERS"   
    FOR EACH ROW   
    BEGIN   
    IF :NEW.CUSTOMER_ID IS NULL OR :NEW.CUSTOMER_ID < 0 THEN  
      SELECT SL_CUSTOMERS_SEQ.nextval   
        INTO :NEW.CUSTOMER_ID  
        FROM DUAL;   
      END IF;   
    END;   
    /
    
    
    
    

    When I try to insert several records with the seq.nextval it gives error

    violation of primary key.

    INSERT INTO "ALIZA"."SL_CUSTOMERS" (CUSTOMER_NAME) VALUES ('sdfsd')
    ORA-00001: unique constraint (ALIZA.SL_CUSTOMERS_PK) violated
    ORA-06512: at line 1
    
    
    
    
    One error saving changes to table "ALIZA"."SL_CUSTOMERS":
    Row 4: ORA-00001: unique constraint (ALIZA.SL_CUSTOMERS_PK) violated
    ORA-06512: at line 1
    
    
    
    
    
    
    
    

    Concerning

    Mr President.

    I find the solution by creating a function before the triiger

    as below

    CREATE SEQUENCE  "ALIZA"."SL_CUSTOMERS_SEQ"  MINVALUE 1 MAXVALUE 9999999999999999999999999999 INCREMENT BY 1 START WITH 1 NOCACHE NOORDER  NOCYCLE ;
    
    CREATE OR REPLACE FUNCTION get_SL_CUSTOMERS_vId RETURN VARCHAR2 AS
    BEGIN
       RETURN SL_CUSTOMERS_SEQ.NEXTVAL;
    
    END;
    /
    
    CREATE OR REPLACE TRIGGER SL_CUSTOMERS_TRG
    BEFORE INSERT ON "ALIZA"."SL_CUSTOMERS"
    FOR EACH ROW
    DECLARE
    dummy VARCHAR2(200);
    BEGIN
      dummy := get_SL_CUSTOMERS_vId();
      :NEW.CUSTOMER_ID := dummy;
    END;
    /  
    

    It works very well

    Thank you all for the suggestions.

    Concerning

  • My V715W was not printing black print cartridge replaced with cartridge Dell, error message says lack of empty, re-installed ink cartridge the cartridge with the same message. Put original cartridge is black and got the same error

    My V715W was not printing black print cartridge replaced with cartridge Dell, error message says lack of empty, re-installed ink cartridge the cartridge with the same message. Put original cartridge is black and got the same error

    My dells V515w printer will not print after that I changed the cartridge, the cartridges black & color dells. There is no print blank paper. Re-installed I'm really lost.

  • Error: ' Service Pack has not been installed. Restoration of the changes. Not turn off not computer. "unable to install Windows Service Pack 2."

    Original title: cannot install Windows Service Pack 2.

    I tried to install Windows Service Pack 2 and you know how when you lock your laptop, it's how he like to appear. Service pack filed to install, so now have him, he said, 'Service Pack was not installed. Restoration of the changes. Do not turn off computer. "I'm not going to let me at all to connect to my computer... Alls for this is restarts by itself and when it turns on, it says the same thing. I already tried to remove the battery and leaving out the laptop for a little while and then when I put the battery in and re - turn on the laptop, it says the same thing and continues to do exactly the same thing and I'm getting really aggravated and crazy. Is there anyway that I can fix it without going through a computer technician?

    Hello

    Have you been able to successfully install the other updates?

    If you have the Windows Vista installation disc, follow this link and check if the problem persists:

    Error: Failed to setup of the Windows updates. Restoration of the changes. Do not turn off your computer when you try to install Windows updates

    See: How to troubleshoot Windows Vista and Windows Server 2008 service pack installation problems?

    Learn how to install Windows Vista Service Pack 2

    Hope the helps of information.

  • I recently purchased Photoshop elements 13.  My employer just changed my computer (I am allowed and only use my personal computer) and the new computer does not have a CD-ROM drive.  Is it possible to download the software elements on my compu

    I recently purchased Photoshop elements 13.  My employer just changed my computer (I am allowed and only use my personal computer) and the new computer does not have a CD-ROM drive.  Is there a way to download the software items on my computer with the serial number and not the CD? Help!

    You can download the trial and use your serial number of the drive to enable to make full use...

    PSE 13 trial - http://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_elements

  • ESXi 5.5 nic teaming/LAG with trunking does not but it works on ESX 4.0.  Both are on the same switch. What gives?

    I have two hosts (vhost1 = ESX 4.0, vhost2 = 5.5 ESX) both are configured for the Group and both connected to a switch of 1544 Adtran L3 (named sw01).  vhost1 has been in production for several years with the config below and has been solid as a rock.  I'm trying to reproduce the installation of grouping/collage on vhost2 and it does not work when are associated but will work when you are using a single NIC (with or without aggregation).

    To be more specific about what does not work, two virtual servers have "Network server" (vlan 8) defined as a group of ports. Both physical and virtual servers on the same vlan cannot ping or resolve queries arp for virtual machines on vhost2.    Everything that is sent from a different subnet can connect to the virtual machines on each virtual server.

    So the question is this: why not ESX 5.5 works as ESX 4.0 when the configs are also near identical, as I can make them and they are connected to the same switch?

    Thanks for any input you can provide!

    S

    This is the configuration for vhost1

    switch 1 (sw01)

    SW01 #sho run int port 3

    Building configuration...

    !

    !

    interface port-channel 3

    Description LAG for vhost1

    no downtime

    switchport mode trunk

    switchport trunk allowed vlan 1.8

    !

    end

    SW01 #sho run int 0/23 concert

    Building configuration...

    !

    !

    0/23 gigabit-switchport interface

    Vhost1 vmnic2 vswitch1 description

    no downtime

    channel-group mode 3 on

    !

    end

    SW01 #sho run int concert 0/24

    Building configuration...

    !

    !

    0/24 gigabit-switchport interface

    Vhost1 vmnic1 vswitch1 description

    no downtime

    channel-group mode 3 on

    !

    end

    vhost1

    [root@vhost1 ~] # esxcfg - NICS - l

    Name PCI Driver link speed Duplex MAC address MTU Description

    vmnic0 03:04.00 tg3 up to 1000Mbps Full 78:e7:d1:5f:01:f4 1500 Broadcom Corporation NC326i PCIe Dual Port Gigabit Server Adapter

    vmnic1 03:04.01 tg3 up to 1000Mbps Full 78:e7:d1:5f:01:f5 1500 Broadcom Corporation NC326i PCIe Dual Port Gigabit Server Adapter

    [root@vhost1 ~] # esxcfg - vmknic - l

    Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

    vmk1 VMkernel - Server NetIPv4 10.1.8.31 255.255.255.0 10.1.8.255 00:50:56:78:9e:7e 1500 65535 true STATIC

    VMkernel - SAN Net IPv4 10.1.252.20 vmk0 255.255.255.0 10.1.252.255 00:50:56:7 c: d8:7e 9000 65535 true STATIC


    [root@vhost1 ~] # esxcfg - vswif - l

    Port Group/DVPort IP IP family name address Netmask Broadcast Enabled TYPE

    Service vswif1 - NetIPv4 management 10.1.1.12 console 255.255.255.0 10.1.1.255 true STATIC


    [root@vhost1 ~] # esxcfg - vswitch - l

    Switch name Num used Ports configured Ports MTU rising ports

    32 4 32 1500 vSwitch0

    Name PortGroup VLAN ID used rising Ports

    0 3 VM network

    Switch name Num used Ports configured Ports MTU rising ports

    vSwitch1 64 12 64 1500 vmnic1, vmnic0

    Name PortGroup VLAN ID used rising Ports

    Server network 8 7 vmnic1, vmnic0

    Console - management service vmnic1 Net0 1, vmnic0

    VMkernel - server 1 vmnic1 Net8, vmnic0

    On the Load Balancing vSwitch it Hash IP value.

    This is the configuration for vhost2

    switch 1

    SW01 #sho run int 4 port

    Building configuration...

    !

    !

    interface port-channel 4

    LAG description for vhost2

    no downtime

    switchport mode trunk

    switchport trunk allowed vlan 1.8

    !

    end


    SW01 #sho run int concert 0/17

    Building configuration...

    !

    !

    0/17 gigabit-switchport interface

    Description vhost2

    no downtime

    channel-group mode 4 on

    !

    end


    SW01 #sho run int concert 0/18

    Building configuration...

    !

    !

    interface gigabit-switchport 0/18

    Description vhost2

    no downtime

    channel-group mode 4 on

    !

    end

    vhost2

    ~ # esxcfg - NICS - l

    Name PCI Driver link speed Duplex MAC address MTU Description

    vmnic0 e1000e up to 1000Mbps Full 00:25:90:e7:0e:9 0000:08:00.00 1500 c Intel Corporation 82574 L Gigabit Network Connection

    vmnic1 0000:09:00.00 e1000e up to 1000Mbps Full 00:25:90:e7:0e:9 d 1500 Intel Corporation 82574 L Gigabit Network Connection

    ~ # esxcfg - vmknic - l

    Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

    Management 10.1.1.15 IPv4 network vmk0 255.255.255.0 10.1.1.255 c 1500 65535 real STATIC 00:25:90:e7:0e:9

    ~ # esxcfg - road - l

    VMkernel itineraries:

    Interface of network gateway subnet mask

    10.1.1.0 255.255.255.0 subnet local vmk0

    by default 0.0.0.0 10.1.1.1 vmk0


    ~ # esxcfg - road - n

    Expiration type neighbor Interface MAC address

    10.1.1.1 00:a0:c8:8 has: ff: 3 b vmk0 19m13s unknown

    ~ # esxcfg - vswitch - l

    Switch name Num used Ports configured Ports MTU rising ports

    vSwitch0 4352 7 128 1500 vmnic0, vmnic1

    Name PortGroup VLAN ID used rising Ports

    Server network 8 1 vmnic0, vmnic1

    Management network 0 1 vmnic0, vmnic1

    On the Load Balancing vSwitch it Hash IP value.

    Hello

    Do you share the vmnic for ESXi management and network of the VM?

    Try to follow the steps in this KB: VMware KB: NICs using EtherChannel grouping allows intermittent network connectivity in ESXi

    Trying to team adapters using EtherChannel, network connectivity is disrupted on an ESXi host. This problem occurs because grouping NIC properties will not propagate to the network management portgroup in ESXi.

    When you configure the ESXi host for grouping of NETWORK cards in attributing to the road based on ip hashload balancing, this configuration is not propagated to the portgroup management network.

    Workaround

    Note: to reduce the possibility network loss please change the route based on the hash of IP using this method of balancing load vSwitch

    1. Close all ports in the physical switch team leaving a single port as active.
    2. Change the Route based on ip hash vSwitch and load balancing management Portgroup.
    3. Set up the physical switch port channel.
    4. Activate the physical switch ports.

    Notes: Using this method will avoid a loss of connection when you switch to a port channel. Also make sure that under the properties for vmk portgroup # used for network management you tick the box "Enabled".

  • Lightroom 6 still does not respond after a certain number of shut downs and restarts

    I used lightroom6 on a computer laptop windows 10 a few months with no problems. The last two days, I'm not able to launch the application after you stop and restart the computer. Windows Task Manager says that he does not.

    Any suggestions?

    I have the original CD but currently away from home and not be able to uninstall and reinstall.

    any help is appreciated.

    Windows Task Manager says that he does not.

    If Lightroom opens upward, disable the use of the GPU in Lightrroom.Uncheck 'Use the graphics processor' preferences > Performance.

    In addition, please ensure that you use the latest version of Lightroom.

    Refer to keep updating Lightroom to download the latest version 6.3

    I have the original CD but currently away from home and not be able to uninstall and reinstall.

    Re installation is not necessary, but you can still use the Photoshop Lightroom Installer direct download link

    Kind regards

    Assani

  • Firefox does not open a session on a particularweb site, I can connect on the same web site with internet explore. What's wrong?

    This is the site web https://merchantcenter.intuit.com/msc/portal/init
    After I typed my username and password, it tries to connect and then just waiting for merchants and refreshs services shows.
    I refreshed firefox and did not help.

    Use this link to make sure your plugins are up-to-date.
    If all are listed as unknown or research, don't worry to their topic.

    Start Firefox in Safe Mode {web link} by holding down the < shift >
    (Mac options)
    key and then from Firefox. Is always the problem?

  • I installed the latest version of Firefox and it does not connect to any Web site. I had no problem with the previous version, I used.

    Can not connect to any Web site.

    texhusky Hello, normally these problems are caused by a security/firewall software which does not recognize and therefore blocks the new versions of firefox. If please delete all the rules of the program for firefox to your firewall and let it detect the new version of the browser again.

    Difficulty of problems connecting to websites after Firefox update

  • My computer is stuck in "configuration updates: stage 3 of 3 0% complete.". Do not turn off your computer. It restarts just over and over again with the same message.

    I have a Dell Inspiron 1525 with Windows Vista, and I have tried the following to fix my endless reboot with the "Configuring updates: stage 3 of 3 0% complete.".  Do not turn off your computer. »

    • I inserted the cd 'Réinstallation DVD Windows Vista', but it won't pop up any kind of prompt for me to do something with it.  I tried putting the cd in what was on the computer and tried leaving him in and restart it - but the cd has no EFFECT.
    • I used the F8 key and I tried the following with no luck: safe mode, safe mode with network, safe mode w / command prompt, enable logging, last known good configuration (Advanced) boot and debug mode.  Most of these options make the monitor off (to make you think he will do something), then it just restarts and did the thing reboot loop again and again.
    • I also tried the repair your computer option to the F8 key.  He asks me to log in as an administrator (but my password does not work).  So, I use the menu drop down and choose the name of my computer and then use my password, and I can connect to "restoration of access options '.  Once I'm in the "System Recovery Options".  I tried the following with no luck: Startup Repair tool, restore the system, Windows complete PC Restore, Windows Memory Diagnostic tool and command prompt.  THE only ONE that I HAVE NOT YET TRIED it IS THE "DELL FACTORY IMAGE RESTORE", it's because I want to try to fix it without losing everything on my hard drive.  Here are the details of the I've tried in the "System Recovery Options".
    • The command prompt says: 32 X:\Windows\system > (I have no idea how to use it, but it's what he says)
    • The memory diagnostic tool reboots the computer, but nothing new happening (just reboot over and over again)
    • In the PC restore full Windows: I tried to put the Windows Vista CD in, but it can not find a valid backup location
    • When I click on the system restore: it is said: "no restore points were created on your computer's system disk.  To create a restore open system protection point.  When I click on the system protection, it is said: "your computer is running in a limited diagnostic State.  If you use the system restore in this limited State, you can't undo the restore operation.  Help topics are not available in this State. "  So I press OK, and I'm back to square one.
    • When I click on startup repair: it says "Startup Repair could not detect a problem.
    • I know there are many many posts on this problem, and I think I've tried all the suggestions on how to solve the problem, but they do not work for me.
    • PLEASE HELP ME!  I need my computer for my college work.  I can't borrow laptop my friend forever!

    Hello

    I guess that part of the question could be a driver which is really old or similar should not be loaded.

    This exit Windows updates on (after you have access) and stop the updates of the driver to load.

    How to disable automatic driver Installation in Windows Vista - drivers
    http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
    http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

    ---------------------------------------------------

    You can use the solutions in this KB - 3 methods and I listed a little help for them below

    The update is not installed successfully, you receive a message, and the computer restarts when you try to
    install an update in Windows Vista
    http://support.Microsoft.com/kb/949358

    Method 1: Start Windows Vista with the Windows installation media and use the repair feature

    How to do a startup repair in Vista
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    You can also do a safe mode startup repair to access the Recovery Options If you have them available
    or use the DVD as described above.

    This tells you how to access the System Recovery Options
    http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

    Try recovery options Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    Method 2: Start the system in safe mode and then use the system restore feature

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    You can also do a restore of the system of starting with a Vista disk.

    Method 3: Rename the Pending.xml file, and then change the registry (this method is part of the advanced troubleshooting)

    See article below for that.

    You can use this method on the updates that have this problem.
    http://support.Microsoft.com/kb/949358

    Hide the update (click right - HIDE in the updates of Windows) and go to the Microsoft Download Center to download
    and install it.

    Microsoft Download Center
    http://www.Microsoft.com/downloads/en/default.aspx

    ------------------------------------------------------

    Once you are in Windows I was running once again reset here as a precaution.

    How to reset the Windows Update components?
    http://support.Microsoft.com/kb/971058

    Hope this helps sort it out for you.
    Rob - bicycle - Mark Twain said it is good.

  • User files Service does not have this logon user failed to load profile and MS Office programs won't load

    I have two problems which I think are related.

    Please note that my OS is Vista Home Premium

    1. when I disabledUAC, I can load the MS Office programs successfully in both of my administrator accounts.

    2 when I have this OPTION enabled, I can load the administrator account that was installed when I reinstalled Vista.

    The other Admin account comes up with a message "the file of user Service has not this logon user failed to load the profile.

    In addition, when I have UAC turned on I can't open any of my MS Office programs, such as MS Word: "Microsoft Word has not been installed for the current user. Please run Setup to install the application.

    When I turn off UAC, I can access my second Admin account, and I can open MS Office programs in both accounts.

    I tried the MS Fixit tool, run checkdsk and sfc/scannow, restarted my computer and threw a brick at her.

    Your advice is appreciated,

    Hasiel1234

    Hi hasiel1234,

    1. what Microsoft fixit tool ran on the computer?

    2. the problem only occurs with Microsoft word application?

    3. using the Microsoft office 2002 application?

    We do not recommend disabling user (UAC) on the computer access control because it prevents unauthorized computer changes.

    I suggest that you enable the user (UAC) on the computer access control and try the steps and check them off below if it helps.

    Method 1

    See the link below and try the steps mentioned them, check if it works.

    Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. Unable to load the user profile.

    http://support.Microsoft.com/kb/947215

    Method 2

    See the below Microsoft article and try the steps mentioned, check if it works.

    Error message "Microsoft Word has not been installed for the current user" in Word 2002

    http://support.Microsoft.com/kb/322206

    I hope this helps!

    Halima S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Windows7 does not have enough memory, but no programs are running and it; s 7.5 GB free on drive C

    In addition to the notification of memory, another notice said I had a corrupted system disk and I had to use the OS disk to restart the machine. This follows several controls blue screen of my C drive to find errors - who showed none. I have to install extra RAM? I also have 2 external hard drives with a total of 21.5 GB on them. I thought Vista was a pain in the behind before Service endless packs fixed which should have been developed before the "monsters of revenue development" has their way with anyone buying a PC. Now this menagerie of fundamental problems. Oh, I forgot to mention that I can't turn "Security Essentials" and followed the suggestions to solve them without result. Somewhere along the way, I decided to try to get MS to give me a technical support for the mess and discovered they provide only TS for 90 days before charging do you explain how to fix problems with their operating system. Doesn't seem to be evidence of confidence on their rear a new OS for 3 months - in fact, it sucks. As you can probably the tone of this note, I feel somewhere between duped and defrauded by my experience with this company. Any help from the community would be greatly appreciated. I hope that I don't offend anyone from the pool of those who are willing to help, but if I had a penny for every new setting procedural of companies offering the TS that effectively limits access to what appears to be a service that we should expect from any company that sells a high-tech product, I could buy a tribute too expensive, elitist to Steve Jobs.  Thanks in advance for any help.

    David L.
    E-mail address is removed from the privacy *.

    All software manufacturers either support only for a limited period, or a specific number or requests.

    Win requires a minimum of 10% of free space to work properly, so 7.5 GB free would mean a 75 GB HD, which I doubt is the case.

    How or what have you tested your drive for CRV?

  • Java 7 9 update does not install in firefox 17. What version of firefox work with the 7 9 java update

    constantly invites you to install when you run an application that uses the update of java 7 9

    Make sure you also have the Java 32 bit version which needs Firefox.

    Update the Java plugin to the latest version.

    See the Platform Java > Java SE 7U9 or Java 6U37 (download the JRE)

Maybe you are looking for

  • Best way to collect information on the bios of HP Desktop

    Whe have several HP Elite 8300 desktop computers. We don't have accurate information how many of them protected by password of bios.  What would be the best method to collect this information from all the computers of HP desktop and export, for examp

  • After you have installed windows 7 on my pc, sometimes different errors whenever I start a game! and I lie down the computer.

    I just installed windows 7 64 bit of vista 32 bit on my acer and then I can't play all games, there is always a different error on games. It has stopped working or a mistake happens! It makes me a little angry when all I wanted was a better pc and no

  • Upgrade of Windows 10 - battery not detected

    Upgrade Windows 10 has left me with battery not detected laptop Aspire 5738. Already tried the reset of the coercive power, no luck. If I can't find a solution, I need to roll back to Windows 7 or be stuck with a portable desktop computer. Any ideas

  • Problem on my laptop in hibernation. NEED HELP!

    model: Compaq Presario CQ42-177TX I have a problem, even when the first time I bought this laptop. Whenever I put my laptop into hibernation, the screen is black as say he was arrested. But the only thing that differs is the market button always ligh

  • CTRL key does not work as expected

    Original title: keyboard Help!   There is a recurring issue going on with my keyboard or very probably my pc... Well first to start with - I use a software type "ventrilo" called "mumble" that uses the 'CTRL' key as a key to talk with others in the s