Setting port channel between UCS - FI and MDS 9124 (Mode F)

Dear team,

We tried to create the channel of port between UCS FI and MDS 9124

But the port channel do not take action in mode F on MDS 9124

FI is in host FC end Mode

We have allowed FC uplink on FI trunking

We have activated NPIV on MDS

We have activated the MDS trunk

FI and MDS in default VSAN

To check that we have changed the way FI FC channels mode and switch port became active, but in E mode

When we enabled CF trunking of uplink on the port mode FI channels and FC Switching became active in mode TE

but in both cases above, showflogi database shows WWPN of SAN alone does not have the any fi.

How to achieve this?

Have read that no need to change the mode switching mode of CF swicthing and keep FC Endhost way

SO how to channel ports with mode F MDS and FI (Display Mode as NProxy)

What is it has nothing to do with the MDS NX - OS version? (https://supportforums.cisco.com/thread/2179129)

If yes how to put as license for ports came with the camera and we don't have any CAP/PAK or license file as she came

with license

Also, we saw 2 files available for download (m9100-s2ek9-kickstart - mz.5.2.8 .bin and m9100-s2ek9 - mz.5.2.8 .bin b b) to use

Thanks and greetings

Jose

Hi Jo Bo.

What version of the software if your MDS race?

On your UCS do connect nxos and show ficelleStringString ficelleT inteface and find the mac address.

It is possible that you could be hitting the bug below. If this is the case, you may need to update the firmware on your MDS.

Add MAC YES '002a6a', '8c604f', '00defb' for 5 k/UCS-FI

http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId= CSCty04686

Symptom:

Link change cannot connect any other Nexus or other Cisco Switch in mode VAN with a port channel F.   Question can be viewed in older versions of 5.1

5.1.3.N1.1a

but not later

5.1.3.N2.1c

Release. Question is also found in

5.2 (1) N1 (1)

and

6.0 (2) N1 (1)

and later versions.

Conditions:

Nexus configured for the link SAN PortChannels or NPIV Nexus mode connected to the UCS via regular F port channel where UCS VAN VAN edge mode switch: YES switch manufactured FI or another Cisco UCS Port WWN: xx:xx:00:2 has: 6a: xx:xx:xx or xx:xx:8 c: 60:4f:xx:xx:xx

Workaround solution:

Turn-off on Nexus 5 k TF-port question link mode does not happen with standard F-PORT SAN to remove Portchannel config

Other Description of the problem:

To check question collect please see the flogi-event history internal errors whenever the port is attempted OLS, AMENDMENTS, PBA counters will increment. This can be determined via the following output, view port internal info to see all the internal-historic port of error events

Tags: Cisco DataCenter

Similar Questions

  • set up to bring the Fibre Channel between UCS of interconnection fiber and Nexus 5548UP.

    by using the following configuration between Nexus5k and UCS FI. the status of channel comes to ini and change to notConnected.

    -------------------------------------------------------------------------------
    FC1/31 431 notConnected swl - 100 F
    FC1/32 431 notConnected swl - 100 F

    -----------------------------------------------------------------------------------

    The system version: 5.2 (1) N1(1b)

    1 on FCoE
    1 active FEX
    active toy-channel-trunk 1
    interface vlan 1 on
    1 active LACP
    1 active LLDP
    1 active NPIV
    1 active sshServer
    1 on GANYMEDE
    1 active telnetServer
    Uni-directional active 1
    1 active VPC

    san-port-channel interface, 100
    active channel mode
    switchport mode F
    switchport trunk allowed vsan 431

    interface fc1/31
    switchport 'SAN PO to UCS - one' description
    channel-group 100
    no downtime

    interface fc1/32
    switchport 'SAN PO to UCS - one' description
    channel-group 100
    no downtime

    interface fc1/31
    switchport mode F
    interface fc1/32
    switchport mode F

    Help, please

    You must update your 5 k at least

    6.0 (2) N1 (2)

  • How to set up communication between Netgear DG834 and Equium M50?

    Can't get Netgear and portable to commmunicate wireless, the amount of the fine if I use the cable between them or fine if I installed the driver for the unit provided with the Netgear Wireless USB plugin. But the wireless card built-in to do not or cannot see the netgear router? Anyone has any idea why

    Hello

    Perhaps is the card not activated correctly? Check the status in the device under network adapters Manager. If everything is ok check FN + F8 key connection and select Wi - Fi is the ACTIVE option.

    After that, you should be able to see WLAN network if the router works well.

  • Setting up iSCSI between ESXi host and MD3000i, firewall Option missing

    I try to configure the iSCSI access and the MD3000i manual head to the firewall option in VI Client.  However, when I go to Configuration - & gt; Profile of security - & gt;  the option firewall appears briefly and disappears?

    I'm having problems to recognize the iSCSI host table and I think that this may be due to the firewall.

    Hello

    I believe that in the latest versions of ESX (3.5u3 for sure), 3260/tcp port (you need for iSCSI) is automatically opened when you turn on the iSCSI (iSCSI software that is).

    You should choose abe to connect using the VI client, click the host in question and select the 'configuration' tab and then the item "security profile. Who should be open all ports.

    Remember that when you use iSCSI, you must as well a VMkernel port and connection of console in your LAN IP storage space. If two IPs per ESX host. The Console launches the iSCSI link, the VMkernel carries the iSCSI connection data.

    EDIT: Sorry, only now I noticed that you are using ESXi. In this case, you won't need a port Console service (because ESXi has one)

    Visit my blog at http://erikzandboer.wordpress.com

  • HP G60 - 430CA: I am trying to set up bluetooth between my phone and my HP with vista laptop flip

    My product name is a laptop HP G60 - 430 that why I can't put up with my flip phone via bluetooth.

    Hello

    Your machine doesn't have a built-in Bluetooth:

    http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c01768915

    You can buy/use USB - Bluetooth dongle to connect

    http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c01768915

    Kind regards.

  • Port-channel problem between fabric Interconnect and vPC N7K

    Hi all

    I have a problem with the Port Uplink channel between fabric interconnect with N7K using vPC

    It's my network for the UCS deployment topology

    N7K I configured vPC for red link and green linkto the fabric Interconnect A I has configured the Port-Channel with Member is Port 1 and Port 2, uplink is red link. Interconnection fabric B, I have configured the Port-Channel with Member's Port 1 and Port 2, uplink's green link.

    The interface port-channel on N7K show is good, each port-channel upwards and have all members. But the fabric Interconnnect, when I see in the UCS Manager, the status of the Port-Channel on Fabic A and fabric B dysfunction not more info: no operational Member. Although all the link is a link to the top and I've got the status of the Port Channel is enabled in the UCS Manager. When I see the properties Port 1, Port to Port-Channel 2, I see the number of members status is: individual. This means channel port is not up and no member in this configuration. I want to using the port-channel load balance and more bandwidth for the uplink of 20Gig. I don't understand why?

    Please help me solve this problem, I have to send the screenshot of UCS Manager when I show the status of the Port-Channel and Port-member in port-channel to reach items.

    Can someone help me solve this problem, thanks a lot. References, please include elements for more details on the fault.

    Thank you

    Trung.

    Hello Nguyen,

    Since the two N7k please collect:

    SH cdp nei

    SH run membership in. X int

    SH sum port-chan

    Thank you

    Matthew

  • Setting up a VPN between a WRVS4400N and ASA device

    I'm a newbie when it comes to Cisco devices and I have a problem setting a VPN between a local and a seat some distance away.

    Here, our local office, we have a device Cisco WRVS4400N Small Business.

    At Headquarters, they have a feature of Cisco ASA.

    We must set up a point to point VPN and I have no idea how to proceed with these devices.

    To compound things, resources, I'm at the other end in an unknown entity that also does not seem to have a lot of experience with this.

    Is there any type of step by step guide for such a configuration?

    If not, can someone please help with this?

    Hello William,.

    I would call 1866-606-1866 Support Center for assistance on the side the tunnel then the entire side of the ASA WRVS has to do is match the settings. If the side ASA needs support with which we can transfer more TAC.

    Cisco Small Business Support Center

    Randy Manthey

    CCNA, CCNA - security

  • FC Port-Channel does not

    Hello

    I need help, I'm setup CF port-channel between 9148 MDS and Cisco fabric Interconnect 6248 and the port-channel does not work. He said no operational members.

    For the MDS, see configuration below:

    NPIV #feature SW (config)

    SW (config) #feature fport-channel-trunk

    SW (config) #interface fc1/17-18

    SW(config-f) force Group-channel mode # 63

    SW(Config-if) F #switchport mode

    SW(Config-if) #switchport trunk-allowed vsan 1-2 (I have only vsan 1 and 2)

    SW (config) #no close

    SW (config) #interface 63 port channel

    SW(Config-if) F #switchport mode

    SW(config-f) #switchport trunk-allowed vsan 1-2

    SW (config) - #no close

    Note: the ports are assigned to vsan 2

    See the attached screenshots for interconnection fabric config

    On the fabric of interconnections switchport mode are defined E. What I have to change to F. If yes where can I change since the option is not there in the UCS Manager?

    have you added the VSANS on the UCSM as well?

    What Code are you runnig on the San Norhbound selector?

    You can be hitting

    https://Tools.Cisco.com/bugsearch/bug/ CSCty04686

  • FC Port-Channel

    Hello

    I'm still new in Cisco nexus environment. I need help on setting up 10 GB FC Port-channel between Cisco Nexus 5548UP switch and the catalyst 6513.

    Help, please.

    Kind regards

    Sorry, but does not support the catalyst 6513 CF native? do you mean MDS 9513?

  • Creation of the VLAN between Powerconnect 5548 and F10 s4810...

    In the coming months we will replace our network equipment.  I was able to get their hands on the new gear at the beginning, and if I'm not traditionally a guy from the network, the project has been given to me and I started playing.  The first thing that I wanted to work on was implemented VLANs.  I have configured the switches like the picture below:

    When I have IP every PC connected to the same subnet and apply VLAN10 to their respective ports, they aren't to pings within the same stack or between cells.  My basic understanding is that they are, do they not?  Did I miss something in my understanding of VLANS or is there a problem with my configs?  I posted the configs below.

    RTTMOACCESS01 config:

    database of VLAN
    VLAN 10,20,30,40,50
    output
    Add a voice vlan Yes-table Nortel___ 000181
    Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
    Add a voice vlan Yes-table 00036 b Cisco_phone___
    Add a voice vlan Yes-table 00096e Avaya___
    Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
    Add a voice vlan Yes-table Shoretel___ 001049
    Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
    VLAN voice Yes-table add 00907 Polycom/Veritel_phone___
    Add a voice vlan Yes-table 00e0bb 3Com_phone___
    860 port address 0.0.0.0 iSCSI target
    port 3260 address 0.0.0.0 iSCSI target
    port 9876 address 0.0.0.0 iSCSI target
    port 20002 address 0.0.0.0 iSCSI target
    20003 port address 0.0.0.0 iSCSI target
    port 25555 address 0.0.0.0 iSCSI target
    hostname rttmoaccess01
    no console logging
    privilege 15
    !
    interface vlan 10
    Name IT
    !
    interface vlan 20
    name UserPCs
    !
    interface vlan 30
    name UserTCs
    !
    interface vlan 40
    the voice name
    !
    interface vlan 50
    Name printers
    !
    gigabitethernet1/0/1 interface
    switchport access vlan 10
    !
    tengigabitethernet1/0/1 interface
    switchport mode general
    switchport general allowed vlan add 10 tag
    switchport general allowed vlan add 20 tag
    switchport general allowed vlan add 30 tag
    switchport general allowed vlan add 40 tag
    switchport general allowed vlan add 50 tag
    !
    gigabitethernet2/0/1 interface
    switchport access vlan 10
    !
    tengigabitethernet2/0/1 interface
    switchport mode general
    switchport general allowed vlan add 10 tag
    switchport general allowed vlan add 20 tag
    switchport general allowed vlan add 30 tag
    switchport general allowed vlan add 40 tag
    switchport general allowed vlan add 50 tag

    !
    Default settings:
    Service etiquette: 76BYTS1
     
    SW version 4.1.0.8 (28 August 2012 time 11:17:36)
     
    Gigabit Ethernet ports
    =============================
    Speed 1000
    full duplex
    negotiation
    flow control
    Auto MDIX
    no back pressure
     
    interface vlan 1
    interface port-channel 1-32
     
    spanning tree
    spanning tree mode RSTP
     
    basis of QoS
    QoS trust cos
    Enable IAS

    RTTMOACCESS02 config:

    database of VLAN
    VLAN 10,20,30,40,50
    output
    Add a voice vlan Yes-table Nortel___ 000181
    Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
    Add a voice vlan Yes-table 00036 b Cisco_phone___
    Add a voice vlan Yes-table 00096e Avaya___
    Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
    Add a voice vlan Yes-table Shoretel___ 001049
    Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
    VLAN voice Yes-table add 00907 Polycom/Veritel_phone___
    Add a voice vlan Yes-table 00e0bb 3Com_phone___
    860 port address 0.0.0.0 iSCSI target
    port 3260 address 0.0.0.0 iSCSI target
    port 9876 address 0.0.0.0 iSCSI target
    port 20002 address 0.0.0.0 iSCSI target
    20003 port address 0.0.0.0 iSCSI target
    port 25555 address 0.0.0.0 iSCSI target
    hostname rttmoaccess01
    no console logging
    privilege 15
    !
    interface vlan 10
    Name IT
    !
    interface vlan 20
    name UserPCs
    !
    interface vlan 30
    name UserTCs
    !
    interface vlan 40
    the voice name
    !
    interface vlan 50
    Name printers
    !
    gigabitethernet1/0/1 interface
    switchport access vlan 10
    !
    tengigabitethernet1/0/1 interface
    switchport mode general
    switchport general allowed vlan add 10 tag
    switchport general allowed vlan add 20 tag
    switchport general allowed vlan add 30 tag
    switchport general allowed vlan add 40 tag
    switchport general allowed vlan add 50 tag
    !
    gigabitethernet2/0/1 interface
    switchport access vlan 10
    !
    tengigabitethernet2/0/1 interface
    switchport mode general
    switchport general allowed vlan add 10 tag
    switchport general allowed vlan add 20 tag
    switchport general allowed vlan add 30 tag
    switchport general allowed vlan add 40 tag
    switchport general allowed vlan add 50 tag
    !
    Default settings:
    Service etiquette: 76BYTS1
     
    SW version 4.1.0.8 (28 August 2012 time 11:17:36)
     
    Gigabit Ethernet ports
    =============================
    Speed 1000
    full duplex
    negotiation
    flow control
    Auto MDIX
    no back pressure
     
    interface vlan 1
    interface port-channel 1-32
     
    spanning tree
    spanning tree mode RSTP
     
    basis of QoS
    QoS trust cos
    Enable IAS

    Config RTTMOCORE

    ! Version 8.3.12.0
    ! Last modification of the configuration to Fri Jun 14 13:31:58 2013 default
    ! Startup-config updated Fri Jun 14 13:32:40 2013 default
    !
    start the primary system battery-unit 0: A:
    start a system secondary battery-unit 0: B:
    start the system stack-unit 0 default: A:
    start the primary system battery-unit 1: A:
    start a system secondary battery-unit 1: B:
    start the system default stack-unit 1: A:
    !
    redundancy full automatic synchronization
    !
    Hardware watchdog
    !
    no console logging
    !
    hostname rttmocore
    !
    disposal of battery-unit 0 S4810
    !
    stack-unit 0 battery-group 14
    !
    stack-unit 0 battery-group 15
    !
    interface TenGigabitEthernet 0/46
    no ip address
    switchport
    FlowControl rx tx off
    no downtime
    !
    interface TenGigabitEthernet 0/47
    no ip address
    switchport
    FlowControl rx tx off
    no downtime

    disposal of battery-unit 1 S4810
    !
    stack stack-unit 1-group 14
    !
    stack stack-unit 1-group 15
    !
    interface TenGigabitEthernet 1/46
    no ip address
    switchport
    FlowControl rx tx off
    no downtime
    !
    interface TenGigabitEthernet 1/47
    no ip address
    switchport
    FlowControl rx tx off
    no downtime
    !
    !
    interface Vlan 1
    !
    interface Vlan 10
    Description IT
    Name IT
    no ip address
    Tagged TenGigabitEthernet 0/46-47
    Tagged TenGigabitEthernet 1/46-47
    Shutdown
    !
    interface Vlan 20
    Description UserPCs
    name UserPCs
    no ip address
    Shutdown
    !
    interface Vlan 30
    Description UserTCs
    name UserTCs
    no ip address
    Shutdown
    !
    interface Vlan 40
    Speech description
    the voice name
    no ip address
    Shutdown
    !
    interface Vlan 50
    Printers description
    Name printers
    no ip address
    Shutdown
    !
    Lldp Protocol
    !
    0 line console
    line vty 0
    line vty 1
    line vty 2
    line vty 3
    line vty 4
    line vty 5
    line vty 6
    line vty 7
    line vty 8
    line vty 9
    !
    end

    I would say lets start with one side and obtain communication of work between the two computers on the same stack at RTTMOACCESS01. The port settings for the 1/01 and 2/01 look great both in access mode for VLAN 10. Which IP addresses and subnets you assign to computers?

    5548 to battery power battery connection 10 also appear to not be in a LAG, then we run two connections like that and they aren't in a SHIFT, we create a loop and a single connection will enter a blocking state.

    For the connections between the 5548 and force 10, I suggest to turn them into a GAP. The command should look like this.

    Console > activate

    Console # configure

    Console (config) # (config) # interface tengigabitethernet 1/0/1

    Console (config) # port - 1 automatic mode group

    output console #.

    Console (config) #.

    Do the same for Te2/0/1

    Then we set up this OFFSET to set it up, and I would try to use the trunk instead of general mode mode.

    Console (config) # interface port-channel 1

    console switchport mode trunk #.

    console # permit trunk switchport vlan add 10,20,30,40,50 tag

    The same should be done for the Force switch 10.

    Te0/46.1/46 in a SHIFT

    Te0/47.1/47 in another SHIFT

    Put in the trunk and let the VLANS on the trunk.

    Allows to study these settings and see if we can make any progress.

    Thank you

  • Internal NETWORK - no port channel (discovery of chassis policy)

    I noticed that I have a link connecting the preference of the group to put anything on my DISCOVERY of the chassis/fex policy

    then I noticed that the tab LAN subnet internal, there is no port selected channel.

    When I change the policy to 1 link and channel ports and reack chassis, I see 4 ports under the internal LAN port channel.

    Is it necessary to change the channel ports policy or can I just leave it to zero?

    What would be the difference?

    Best practice is to use the port-channel between IOM and FI; (This requires second-generation material for FI (62xx) and IOM (220 x)

    If your discovery strategy is set to 1 and you ack frame, it will automatically create a pc of 4 links.

  • Determine the NIF port used by the HEART when it is configured in a port channel

    I recently saw an excellent video of live Cisco UCS troubleshooting performance that showed how to track traffic network within Cisco UCS. The speaker made a comment however, to determine that NIF is used by a high HEAT when port-channels are used between the FEX and FI there are different commands to run. You will need to determine the outcome of hash-load balancing. Unfortunately, he never entered what were these commands.

    Then when we have pinned port-channel instead of HIFs and NIFs veths, what commands will indicate which way is used?

    Matt,

    You can use this command:

    B (nxos) # sh port-channel - balance load< this="" will="" tell="" you="" the="" load="" balance="" method="">

    If you use source-dest-ip as in my case, you can use this command:

    B (nxos) # sh port-channel - the balance of the charge-transfer interface port-channel ID vlan ID x.x.x.x y.y.y.y dst - ip, src - ip and it will show you something like this:

    Lack of params will be substituted by 0.

    Algorithm to balance the load on the switch: source-dest-ip
    crc8_hash: 109 port id coming out: EthernetX / Y  < this="" is="" what="" you="" are="" looking="" for="">
    Param (s) used to balance the load to calculate:
    DST - ip: y.y.y.y
    SRC - ip: x.x.x.x
    DST - mac: 0000.0000.0000
    CBC - mac: 0000.0000.0000

    For the blade, depends on which the active vNIC is, for the FEX, depends on pinning, based on the server is located in the blade slot.  Strange servers go through odd links and same servers through the same ports.

    Remember to rate helpful answers.

    -Kenny

  • SH cdp neighbors port-channel command

    Hello

    I have a strange problem with the command sh cdp neighbors port-channel on my 3750 and 4500switches.

    When I execute the command ' sh cdp neighbors port-channel. I don't see my say on this interface.

    The command 'sh cdp nei' with the port-channel works very well and shows all my neighbors.

    switch #sh cdp neighbors port-channel 1

    Ability code: R - router, T - bridge Trans, B - road Source bridge
    S switch, H - host, I - IGMP, r - Repeater, P - phone.
    D / remote, C - AEVC, M - two port Mac relay

    Device ID Local Intrfce Holdtme Port platform capability ID

    switch #sh ether summary
    Flags: - Low P - D bundled in port-channel
    I have - autonomous s - suspended
    H Eve (LACP only)
    R - Layer 3 S - Layer2
    U - running f - cannot allocate an aggregator

    M - don't use, minimum contacts not satisfied
    u - unfit to tied selling
    w waiting to be aggregated
    d default port

    Number of channels: 1

    Number of aggregators: 2

    Protocol for the Port-Channel port group
    ------+-------------+-----------+-----------------------------------------------
    1 Po1 (SU) LACP Gi1/0/1 (P) article gi1/0/2 P)

    I tried the command on multiple versions of IOS, but always the same question. When I try the command on a 6506-E, it works fine...

    This ordering platform is connected?

    SWITCH2 # sh etherchannel summary
    Flags: - Low P - D bundled in port-channel
    I have - autonomous s - suspended
    H Eve (LACP only)
    R - Layer 3 S - Layer2
    U - N running - is not in service, no aggregation
    f cannot allocate an aggregator

    M not in use, no aggregation due to minimum links has not met
    m don't use, port do not associate due to not meeting minimum links
    u - unfit to tied selling
    d default port

    w waiting to be aggregated
    Number of channels: 7
    Number of aggregators: 7

    Protocol for the Port-Channel port group
    ------+-------------+-----------+-----------------------------------------------
    1 Po1 (SU) LACP Gi1/1 (P) Gi1/2 (P)
    ...

    SWITCH2 #sh cdp nei port-channel 1
    Ability code: R - router, T - bridge Trans, B - road Source bridge
    S switch, H - host, I - IGMP, r - Repeater, P - phone

    Device ID Local Intrfce Holdtme Port platform capability ID
    switch to Gig 1 / 2 123 S I Gig 1/0/1
    switch to Gig 1 / 1 123 S I Gig 1/0/2

    Thank you

    Best regards

    Joris

    Hi Joris,

    It is a known problem and is documented as a cosmetic bug internal. Logically speaking, CDP is not supported on etherchannel interfaces and 'sh cdp port-channel' command should not be available.

    The platform of 6500, although the "port channel show cdp neighbor" returns the result, it's just for convenience and does not mean that the CDP is supported on the port channels. In fact, if you try to enable CDP on port-channel on 6500, it generates an error:

    PO1 #int 6500 (config)

    6500(Config-if) #cdp en

    % CDP is not supported on this interface, or for this encapsulation

    If you run "debug cdp events", you can see the packets exchanged on the physical interface rather than on the port-channel. Correct way is to check the neighborship of the cdp on the physical interfaces.

    See you soon,.

    Shashank

    Please rate if you find the content useful

  • 6248 fabric interconnects FC interfaces and MDS ports license

    Hello

    I need help. I need to configure port-channel of CF between 2 x 9148 MDS and 2 x Cisco fabric interconnects. My main problem here is interfaces CF appear not on the fabric of interconnections (UCS Manager). I don't see ethernet ports. I have to turn on the unified ports or do I license for CF?

    I also connected the ds-sfp-fc8g-sw FPS but I get the error "operation status failed, reason: SFP Validation failed.

    Another thing, all 48 FC ports on switches DMS 9148 acquire the license. Aren't they supposed to come with 16 ports enabled by default?

    Any ideas?

    Hi Selby

    6248 FI unified ports, by default, all are Ethernet; so as a first step, you must configure the FC ports.

    You just need Ethernet port licenses, which are also universal.

    See, for example.

    https://supportforums.Cisco.com/message/3763853#3763853

    For SDM 9148 licenses take a look on

    http://www.Cisco.com/c/en/us/products/collateral/storage-networking/MDS-9148-multilayer-fabric-switch/data_sheet_c78-571411.html

    There are packages with

    Cisco MDS 9148 48 - Port Multilayer Fabric Switch with 16, 32 or 48 active ports of 8 Gbps

    Good luck

  • Channel between 3560 port s two orange lights

    We have a port pagp channel set up between two 3560 switches.  One of the switches indicates the port channel in blocking for one of our virtual local networks and for these ports leds blink orange.  There is no duplex incompatibilities or speed.  The STP blocking the cause?

    Hello!

    Hmmm... I can't really guarantee you until you give us the show spanning-tree VLAN 7 output for two switches.

    However, I'm almost certain that this is not a crucial problem which may have an impact on your network.

    Kind regards!

Maybe you are looking for

  • Satellite Pro L650/L650D does not start

    My laptop Toshiba does not work... When he was for a restart, the it closed suddenly... I want to start (start), but when I clicked on the Start button, it does not start... The LED lights were lit, but the laptop does not start...At the present time

  • Laptop HP G70-120EA

    Hello Can you tell me if I install a new hard drive on my HP G70 can I switch to 64-bit Windows? Concerning Fred

  • Display the name change for the story?

    Hi all I was wondering, if I change my display name (not username, of course), which would change my nickname for ALL past and present message and call history/records (not only recent but all THE records taken)? A quick response would be greatly app

  • invalid product code Windows vista

    I installed a copy of the CAP manufacturers windows vista 32 - bit system on an old computer, I built that was running xp pro sp3.  Now Iam locked due to the valid product code.  I would like to be able to enter my system to restore windows xp pro sp

  • Network printer cannot connect through IE

    I successfully download an HP network printer.  I am running Vista and IE8.  Indications (FixIt, printer troubleshooting) all indicate there is no problem.  In fact, the FixIt Windows downloaded without any problem.  Yet, when I try to access the pri