Setting up a VPN between a WRVS4400N and ASA device

Similar Questions

• 'How to' set up a VPN between a UC540 and a SR520 with remote IP extension

  Hi all

  I need help in establishing a link between a head office UC540 and a distance SR520 I want to use a PC and an IP phone in. This remote site is the first of many.

  I found several examples of IPsec VPN site, but none with references to some VLAN voice and data, should I worry or the phone will only work.

  All the tips and suggestions accepted with gratitude,

  Jerry

  Here is an example of configuration LAN-to-LAN VPN between 2 IOS routers:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080194650.shtml

  Assuming that your example:

  VLAN 1 - data - 192.168.19.0/24

  VLAN 100 - voice - 10.1.1.0/24

  And on the other side:

  VLAN 1 - data - 192.168.20.0/24

  VLAN 100 - voice: 10.2.2.0/24

  The crypto ACL would be:

  access-list 150 permit ip 192.168.19.0 0.0.0.255 192.168.20.0 0.0.0.255

  access-list 150 permit ip 10.1.1.0 0.0.0.255 10.2.2.0 0.0.0.255

  Crypto ACLs on the other side are the following:

  access-list 150 permit ip 192.168.20.0 0.0.0.255 192.168.19.0 0.0.0.255

  access-list 150 permit ip 10.2.2.0 0.0.0.255 10.1.1.0 0.0.0.255

• VPN between 878 router and ASA 5505

  Hello world

  I struggled for a few days now to get a VPN connection works.

  The situation

  Two offices needs to be connected to eachother with a VPN. The two parties have a WAN connection.

  The tunnel between locations rises very well but the communication fails in almost any way.

  The host cannot ping each other and also the inside of the router and ASA pings fail.

  The only ping works is from inside Site2 to the inside interface of the router side 1 (192.168.1.100 to 192.168.0.250)

  NAT works very well on both sites behind the router / asa.

  I think I'm doing something wrong with the roads or access lists but after 7 days, many refills, restores, driving from one end of the State to the other to reset stupid moves break and resolder my cable from the console and things completely with default start for 10 times, I'm through, I honestly don't know where to look for more...

  Tech Specs:

  Site1: has a cable modem that gives a WAN IP with DHCP address

  This modem connects to the Cisco 878 (Fastethernet0) router

  The router acts as a DHCP server and NAT gateway for the office and offers vpn connectivity to the other office

  Site2: has a cable-modem/router (Cisco 3925), which made the NAT, this modem/router gives an IP private class-C (192.168.178.x)

  This modem/router connects to a Cisco ASA 5505 (Fastethernet0)

  The ASA also server as a DHCP server and NAT gateway for the office and offers vpn connectivity to the other office.

  Online, it looks like this:

  Office 1--> Cisco878--> WAN Cloud<---cablemodemrouter><--- asa5505=""><--- office="">

  IP address ranges:

  Office 1

  Network 192.168.0.0

  Subnet mask 255.255.255.0

  Gateway 192.168.0.250

  IP WAN XXXX

  Office 2

  Network 192.168.1.0

  Subnetmak 255.255.255.0

  Gateway 192.168.1.1

  IP WAN XXXX

  On the location of office 2, there is a NAT between ASA and WAN router. between 192.168.178.x 255.255.255.0

  The modemrouter is a Cisco 3925, on which IPSEC passthrough is enabled.

  Configs:

  Site 1:

  CISCO 878 router

  Site 2

  ASA 5505

  I hope someone has a chance to look through my config and tell me what I did wrong this week

  Even if you can not help me but still read here: Thank YOU!

  (As my problem has been resolved, I removed the configs of this post. If for any reason, you want to work for these devices configuration, please send me a PM)

  Post edited by: taaa lijf - reason: problem solved, removed configs and stuff private for obvious reasons ;)

  Hello

  Ping client customer site 1 site2 and make sh crypto isakmp his and sh crypto ipsec his on the router.

  If sh crypto isakmp gives QM_Idle and ping fails and you have no package in the HS cypto ipsec his and then do a debug crypto ipsec

  If sh crypto isakmp gives MM_NoState can do a debug crypto isakmp

  One note however, you should have ip addresses static at least on the side, initiating the tunnel, otherwise it will not work when ip address changes.

  Kind regards.

  Alain.

• VPN between a PIX and a VPN 3000

  I'm trying to set up a VPN between PIX and a VPN 3000. All configurations are complete, but the tunnel has not been established. On the PIX, to 'see the crypto engine' and ' show isakmp his ' orders, I do not see the tunnel. Of "show ipsec his ' command, I can see the mistakes"#send"continues to increase when I try to connect to the remote network. Here is the copy - paste command:

  Tag crypto map: myvpnmap, local addr. 10.70.24.2

  local ident (addr, mask, prot, port): (10.70.24.128/255.255.255.128/0/0)

  Remote ident (addr, mask, prot, port): (10.96.0.0/255.224.0.0/0/0)

  current_peer: 10.70.16.5:0

  LICENCE, flags is {origin_is_acl},

  #pkts program: encrypt 0, #pkts: 0, #pkts 0 digest

  #pkts decaps: 0, #pkts decrypt: 0, #pkts check 0

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, #pkts compr. has failed: 0, #pkts decompress failed:

  #send 12, #recv errors 0

  local crypto endpt. : 10.70.24.2, remote Start crypto. : 10.70.16.5

  Path mtu 1500, fresh ipsec generals 0, media, mtu 1500

  current outbound SPI: 0

  SAS of the esp on arrival:

  the arrival ah sas:

  SAS of the CFP on arrival:

  outgoing esp sas:

  outgoing ah sas:

  outgoing CFP sas:

  Obviously, the PIX identifies protected traffic but failed to establish the tunnel. I was wondering what could be the reason for these kind of mistakes? That means them growing '#send errors?

  Thank you very much!

  Sending error mean simply the PIX is grateful to encrypt this traffic, but there is no built tunnel and so it must drop the package.

  you will need to look at why the tunnel is not under construction however, "sending error" are just a byproduct of some other configuration issue. On the PIX, it looks like you would have something like:

  Crypto ip 10.70.24.128 access list allow 255.255.255.128 10.96.0.0 255.224.0.0

  On the 3000 under the L2L section and the Local and remote network, you need the exact opposite of the latter, then it would be:

  / Local network mask = 10.96.0.0/0.31.255.255

  / Remote network mask = 10.70.24.128/0.0.0.127

  If you have something else the tunnel will fail to come. Otherwise, we see that the Cryptography debugs the PIX and the trunk of the 3000 when the tunnel is built.

• PPTP VPN between clients Windows and Cisco 2921 router

  Hi all!

  I have a problem with PPTP VPN between Windows clients and router Cisco 2921 with permission of RADIUS (IAS). When I try to connect to Cisco 2921 of Windows 7 by using MS-CHAP v2 I get the message 778: it was not possible to verify the identity of the server. Can I use PAP - power is OK. On Windows XP, the same situation.

  Cisco config:

  version 15.0

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  hostname gw.izmv

  !

  boot-start-marker

  boot-end-marker

  !

  logging buffered 51200 warnings

  !

  AAA new-model

  !

  AAA authentication ppp default local radius group of

  !

  AAA - the id of the joint session

  !

  clock timezone + 002 2

  !

  No ipv6 cef

  IP source-route

  IP cef

  !

  !

  Authenticated MultiLink bundle-name Panel

  !

  Async-bootp Server dns 192.168.192.XX

  VPDN enable

  !

  VPDN-Group 1

  ! PPTP by default VPDN group

  accept-dialin

  Pptp Protocol

  virtual-model 1

  echo tunnel PPTP 10

  tunnel L2TP non-session timeout 15

  PMTU IP

  adjusting IP mtu

  !

  redundancy

  !

  interface Loopback0

  IP 192.168.207.1 255.255.255.0

  !

  !

  interface GigabitEthernet0/0

  Description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE $ 0/0

  IP 192.168.192.XXX 255.255.255.0

  IP 192.168.192.XX 255.255.255.0 secondary

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  !

  interface GigabitEthernet0/1

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  !

  interface GigabitEthernet0/2

  Description - Inet-

  no ip address

  NAT outside IP

  IP virtual-reassembly

  automatic duplex

  automatic speed

  PPPoE enable global group

  PPPoE-client dial-pool-number 1

  No cdp enable

  !

  !

  interface virtual-Template1

  IP unnumbered Loopback0

  IP mtu 1492

  IP virtual-reassembly

  AutoDetect encapsulation ppp

  by default PPP peer ip address pool

  PPP mppe auto encryption required

  PPP authentication ms-chap-v2

  !

  !

  interface Dialer1

  the negotiated IP address

  NAT outside IP

  IP virtual-reassembly

  encapsulation ppp

  Dialer pool 1

  Dialer-Group 1

  PPP authentication pap callin

  PPP pap sent-username DSLUSERNAME password DSLPASSWORD

  No cdp enable

  !

  !

  IP local pool PPP 192.168.207.200 192.168.207.250

  IP forward-Protocol ND

  !

  !

  overload of IP nat inside source list NAT_ACL interface Dialer1

  IP nat inside source static tcp 192.168.192.XX 25 expandable 25 82.XXX.XXX.XXX

  IP nat inside source static tcp 192.168.192.XX 1352 82.XXX.XXX.XXX 1352 extensible

  IP route 0.0.0.0 0.0.0.0 Dialer1

  !

  NAT_ACL extended IP access list

  deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255

  deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255

  deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255

  deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255

  permit tcp 192.168.192.0 0.0.0.255 any eq www

  permit tcp 192.168.192.0 0.0.0.255 any eq 443

  permit tcp 192.168.192.0 0.0.0.255 any eq 1352

  permit tcp host 192.168.192.XX no matter what eq smtp

  permit tcp 192.168.192.0 0.0.0.255 any eq 22

  permit tcp host 192.168.192.XX no matter what eq field

  permit tcp host 192.168.192.XX no matter what eq field

  permit tcp host 192.168.192.XX no matter what eq field

  allowed UDP host 192.168.192.XX matter what eq field

  allowed UDP host 192.168.192.XX matter what eq field

  allowed UDP host 192.168.192.XX matter what eq field

  !

  host 192.168.192.XX auth-port 1645 1646 RADIUS server acct-port

  Server RADIUS IASKEY key

  !

  control plan

  !

  !

  !

  Line con 0

  line to 0

  line vty 0 4

  line vty 5 15

  !

  Scheduler allocate 20000 1000

  end

  Debugging is followed:

  14:47:51.755 on 21 oct: PPP: Alloc context [294C7BC4]

  14:47:51.755 on 21 oct: ppp98 PPP: Phase is

  14:47:51.755 on 21 oct: ppp98 PPP: using AAA Id Unique = 8 b

  14:47:51.755 on 21 oct: ppp98 PPP: permission NOT required

  14:47:51.755 on 21 oct: ppp98 PPP: via vpn, set the direction of the call

  14:47:51.755 on 21 oct: ppp98 PPP: treatment of connection as a callin

  14:47:51.755 on 21 oct: ppp98 PPP: Session Session handle [62] id [98]

  14:47:51.755 on 21 oct: ppp98 TPIF: State of the event [OPEN] [initial check]

  14:47:51.755 on 21 oct: ppp98 PPP LCP: switch to passive mode, State [stopped]

  14:47:53.759 on 21 oct: ppp98 PPP LCP: exit passive mode, State [departure]

  14:47:53.759 on 21 oct: LCP ppp98: O CONFREQ [departure] id 1 len 19

  14:47:53.759 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:53.759 on 21 oct: ppp98 TPIF: AuthProto MS-CHAP-V2 (0x0305C22381)

  14:47:53.759 on 21 oct: ppp98 TPIF: MagicNumber 0xF018D237 (0x0506F018D237)

  14:47:53.759 on 21 oct: ppp98 TPIF: event [UP] State [departure at REQsent]

  14:47:54.351 on 21 oct: ppp98 TPIF: I CONFREQ [REQsent] id 0 len 18

  14:47:54.351 on 21 oct: ppp98 TPIF: MRU 1400 (0 x 01040578)

  14:47:54.351 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)

  14:47:54.351 on 21 oct: ppp98 TPIF: PFC (0 x 0702)

  14:47:54.351 on 21 oct: ppp98 TPIF: RAC (0 x 0802)

  14:47:54.351 on 21 oct: LCP ppp98: O CONFNAK [REQsent] id 0 len 8

  14:47:54.351 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:54.351 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq-] [REQsent to REQsent]

  14:47:54.751 on 21 oct: ppp98 TPIF: I CONFACK [REQsent] id 1 len 19

  14:47:54.751 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:54.751 on 21 oct: ppp98 TPIF: AuthProto MS-CHAP-V2 (0x0305C22381)

  14:47:54.751 on 21 oct: ppp98 TPIF: MagicNumber 0xF018D237 (0x0506F018D237)

  14:47:54.751 on 21 oct: ppp98 TPIF: State of the event [receive ConfAck] [REQsent to ACKrcvd]

  14:47:54.915 on 21 oct: ppp98 TPIF: I CONFREQ [ACKrcvd] id 1 len 18

  14:47:54.915 on 21 oct: ppp98 TPIF: MRU 1400 (0 x 01040578)

  14:47:54.915 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)

  14:47:54.915 on 21 oct: ppp98 TPIF: PFC (0 x 0702)

  14:47:54.915 on 21 oct: ppp98 TPIF: RAC (0 x 0802)

  14:47:54.915 on 21 oct: LCP ppp98: O CONFNAK [ACKrcvd] id 1 len 8

  14:47:54.915 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:54.915 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq-] [ACKrcvd to ACKrcvd]

  14:47:55.275 on 21 oct: ppp98 TPIF: I CONFREQ [ACKrcvd] id 2 len 18

  14:47:55.275 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:55.275 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)

  14:47:55.275 on 21 oct: ppp98 TPIF: PFC (0 x 0702)

  14:47:55.275 on 21 oct: ppp98 TPIF: RAC (0 x 0802)

  14:47:55.275 on 21 oct: LCP ppp98: O CONFACK [ACKrcvd] id 2 len 18

  14:47:55.275 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:55.275 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)

  14:47:55.275 on 21 oct: ppp98 TPIF: PFC (0 x 0702)

  14:47:55.275 on 21 oct: ppp98 TPIF: RAC (0 x 0802)

  14:47:55.275 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq +] [ACKrcvd to open]

  14:47:55.295 on 21 oct: ppp98 PPP: Phase is AUTHENTICATING,

  14:47:55.295 on 21 oct: ppp98 MS-CHAP-V2: O CHALLENGE id 1 len 28 of 'gw.izmv '.

  14:47:55.295 on 21 oct: ppp98 TPIF: State is open

  14:47:55.583 on 21 oct: ppp98 MS-CHAP-V2: I ANSWER id 1 len 71 of "domain\username".

  14:47:55.583 on 21 oct: ppp98 PPP: Phase TRANSFER, tempting with impatience

  14:47:55.583 on 21 oct: ppp98 PPP: Phase is AUTHENTICATING, unauthenticated user

  14:47:55.587 on 21 oct: ppp98 PPP: request sent MSCHAP_V2 LOGIN

  14:47:55.591 on 21 oct: ppp98 PPP: received LOGIN response PASS

  14:47:55.591 on 21 oct: ppp98 PPP AUTHOR: author data NOT available

  14:47:55.591 on 21 oct: ppp98 PPP: Phase TRANSFER, tempting with impatience

  14:47:55.595 on 21 oct: Vi3 PPP: Phase is AUTHENTICATING, authenticated user

  14:47:55.595 on 21 oct: Vi3: given msg No. MS_CHAP_V2

  14:47:55.595 on 21 oct: Vi3 MS-CHAP-V2: SUCCESS O id 1 len 46 msg is "tG @ #QDD @(@B@ (@[email protected]/ ** / @I @:[email protected]/ ** / @@@ EJFDE)).

  14:47:55.595 on 21 oct: Vi3 PPP: Phase is in PLACE

  14:47:55.595 on 21 oct: Vi3 CPIW: protocol configured, start state cf. [original]

  14:47:55.595 on 21 oct: Vi3 CPIW: State of the event [OPEN] [Initial report on startup]

  14:47:55.595 on 21 oct: Vi3 CPIW: O CONFREQ [departure] id 1 len 10

  14:47:55.595 on 21 oct: Vi3 CPIW: address of 192.168.207.1 (0x0306C0A8CF01)

  14:47:55.595 on 21 oct: Vi3 CPIW: event [UP] State [begins to REQsent]

  14:47:55.595 on 21 oct: Vi3 CCP: protocol configured, start state cf. [original]

  14:47:55.595 on 21 oct: Vi3 CCP: State of the event [OPEN] [Initial report on startup]

  14:47:55.595 on 21 oct: Vi3 CCP: O CONFREQ [departure] id 1 len 10

  14:47:55.595 on 21 oct: Vi3 CCP: MS - PPC supported bits 0 x 01000060 (0 x 120601000060)

  14:47:55.595 on 21 oct: Vi3 CCP: event [UP] State [begins to REQsent]

  14:47:55.599 on 21 oct: % LINK-3-UPDOWN: Interface virtual-access.3, changed State to

  14:47:55.603 on 21 oct: % LINEPROTO-5-UPDOWN: Line protocol on Interface virtual-access.3, changed State to

  14:47:56.027 on 21 oct: Vi3 LCP: I have TERMREQ [open] id 3 len 16

  14:47:56.027 on 21 oct: Vi3 LCP: (0x2F7C5F7E003CCD740000030A)

  14:47:56.027 on 21 oct: Vi3 CPIW: event [BOTTOM] State [REQsent on startup]

  14:47:56.027 on 21 oct: Vi3 CPIW: State of event [CLOSE] [begins with initial]

  14:47:56.027 on 21 oct: Vi3 CCP: event [BOTTOM] State [REQsent on startup]

  14:47:56.027 on 21 oct: Vi3 PPP DISC: MPPE required not negotiated

  14:47:56.027 on 21 oct: Vi3 PPP: sending Acct event [low] id [8B]

  14:47:56.027 on 21 oct: Vi3 CCP: State of event [CLOSE] [start with initial]

  14:47:56.027 on 21 oct: Vi3 LCP: O TERMACK [open] id 3 len 4

  14:47:56.027 on 21 oct: Vi3 LCP: event [receive TermReq] State [Open to stop]

  14:47:56.027 on 21 oct: Vi3 PPP: Phase ENDS

  14:47:56.027 on 21 oct: Vi3 LCP: event [CLOSE] [off status of closing]

  14:47:56.675 on 21 oct: Vi3 PPP: block vaccess to be released [0x10]

  14:47:56.675 on 21 oct: Vi3 LCP: event [CLOSE] State [closing closing]

  14:47:56.679 on 21 oct: Vi3 LCP: event [BOTTOM] State [closing on Initial]

  14:47:56.679 on 21 oct: Vi3 PPP: compensation AAA Id Unique = 8 b

  14:47:56.679 on 21 oct: Vi3 PPP: unlocked by [0x10] always locked by 0 x [0]

  14:47:56.679 on 21 oct: Vi3 PPP: free previously blocked vaccess

  14:47:56.679 on 21 oct: Vi3 PPP: Phase is BROKEN

  14:47:56.679 on 21 oct: % LINK-3-UPDOWN: Interface virtual-access.3, changed State to down

  14:47:56.683 on 21 oct: % LINEPROTO-5-UPDOWN: Line protocol on Interface virtual-access.3, state change downstairs

  I'll be very grateful for any useful suggestions

  We had the same problem using MS-CHAP-V2 and 3945 router using IOS 15.2. When you add the same combination of username/password locally it worked fine but it wasn't no of course of the solution. We have solved this problem by adding the following line in the config file:

  AAA authorization network default authenticated if

  This is because Windows 2000 clients require the use of a statement of authorization aaa in the router config. Maybe it was default (and therefore not shown) previous iOS releases.

  Success!

  Wil Schenkeveld

• I followed the instructions to set up the home between my Mac and iPhone sharing 6, but I don't understand all the music on my iPhone

  I followed the instructions to set up the home between my Mac and iPhone sharing 6, but I don't understand all the music on my iPhone

  I have confirmed:

  (1) devices are on the same network

  (2) I am connected to my AppleID with the same account

  3) are my OS up to date (Mac 10.11.2) (9.2 iPhone)
  (3) I closed iTunes and the App has reopened

  (4) I turned my iPhone off and rebooted (and confirms the foregoing)

  On my iPhone, I see in my music library, different ' kind' listed (e.g., classic, recently added, music of the 1990s, etc.) but they are all empty.

  Im hoping to see the music I have in iTunes on my Mac and play these songs on my iPhone.

  IM thinking, music that would be shared from my computer to my phone will be on the cloud?

  (I did not all default to add my music in the cloud at the moment).

  Post edited by: abbeyinor

  Did you go into settings > music on your phone and sign in home sharing?

  See you soon,.

  GB

• EIGRP running between the router and ASA by switch

  Hello

  Is that possible I can running an EIGRP between router and ASA by switch?

  Router and ASA connected to the switch with static route.

  Hi Tommy Chin.

  It is possible, we must advertise to the route between the router and ASA.

  Please provide your connectivity diagram to better explain.

  For example...

  interface GigabitEthernet0/0

  Description links to WAN router

  nameif OUTSIDE

  security-level 50

  IP 10.1.1.1 255.255.255.192 ensures 10.1.1.2

  Summary-address eigrp 100 10.1.0.0 255.255.0.0 1

  !

  Confiuration Protocol EIGRP

  standard access list eigrpACL_FR allow a

  !

  Router eigrp 100

  eigrpACL_FR distribute-list in the interface outside

  neighbor 10.1.1.3 OUTSIDE interface

  neighbor 10.1.1.2 OUTSIDE interface

  Network 10.1.1.0 255.255.255.192

  redistribute connected

  redistribute static

  !

  Kind regards

  Srinivas.

  Note: if it solves your problem it mark it as resolved.

• I need help setting up a network between Windows Vista and Windows 7.

  original title: HELP me to SET UP a NETWORK FOR WINDOWS VISTA AND PORTABLE WINDOWS 7 DESKTOP AND a DLINK WIRELESS ROUTER

  HELP ME TO SET UP A NETWORK OF WINDOWS VISTA DESKTOP AND LAPTOP WINDOWS 7 AND A DLINK WIRELESS ROUTER

  Hello

  You can follow the procedure from the following link: networking computers running different versions of Windows: http://windows.microsoft.com/en-US/windows7/Networking-home-computers-running-different-versions-of-Windows

• Installation of site to site VPN IPSec using PIX and ASA

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  I am a site configuration to site IPSec VPN using a PIX515E to site A and ASA5520 to Site B.

  I have attached the lab diagram. Consider PIX and ASA are in default configuration, which means that nothing is configured on both devices.

  According to the scheme

  ASA5520

  External interface is the level of security 11.11.10.1/248 0

  The inside interface is 172.16.9.2/24 security level 100

  Default route is 0.0.0.0 0.0.0.0 11.11.10.2 1

  PIX515E

  External interface is the level of security 123.123.10.2/248 0

  The inside interface is 172.16.10.1/24 security level 100

  Default route is 0.0.0.0 0.0.0.0 123.123.10.1 1

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  Could someone tell me how to set up this configuration? I tried but didn't workout. Here is the IKE protocol I have used.

  IKE information:

  IKE Encrytion OF

  MD5 authentication method

  Diffie Helman Group 2

  Failure to life

  IPSEC information:

  IPsec encryption OF

  MD5 authentication method

  Failure to life

  Please enter the following command

  on asa

  Sysopt connection permit VPN

  on pix not sure of the syntax, I think it is

  Permitted connection ipsec sysopt

  What we are trying to do here is basically allowing vpn opening ports

  Alternatively you can open udp 500 and esp (or port ip 50) out to in on the two firewalls

• Remote IPSec VPN - client Windows 7 and ASA 5505

  Hello

  I'm having trouble with configuring IPSec VPN with Cisco ASA 5505 and Windows 7 client native VPN remotely. My client PC Gets the VPN IP pool address and can access a remote network behind ASA, but then I lose my internet connection. I read that this should be a problem with the split tunneling, but I did as it says here and no luck.

  Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have an internet connection (given that the customer is using a local gateway), but then I can't ping remote network.

  In the log, I see the warnings of this type:

  TCP connection of disassembly 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0: 00:00 0 stream bytes is a loopback (cisco)

  I have attached my configuration file (without configuring split tunneling, I tried). If you need additional newspapers, I'll send them right away.

  Thank you for your help.

  Petar Koraca

  That's what you would have needed on versions 8.3 and earlier versions:

  permit same-security-traffic intra-interface

  Global 1 interface (outside)

  NAT (outside) 1 192.168.150.0 255.255.255.0

  However I see that you are running 8.4 so I think that all you need is this (I never did on 8.4 so it may not be accurate)

  permit same-security-traffic intra-interface

  network of the NETWORK_OBJ_192.168.150.0_24 object

  dynamic NAT interface (outdoors, outdoor)

  Give it a shot and let me know how it goes.

• IPSEC VPN between Pix 515E and 1841 router

  Hi all

  BACKGROUND

  We have implemented a site to site VPN IPSEC between a Pix 515E 8.0 operation (4) and an 1841 using static IP addresses at both ends. We used CCP on the router and the ASDM the pix to build initial tunnels. Now the site with the router is evolving into a dynamic IP address from the ISP so we have implemented dynamic DNS to update dynamic IP address.

  PROBLEM

  The problem is that ASDM will not allow us to set a domain as the address of peers, it will not accept an IP address. We believe that the solution will be to remove the static Crypto map and replace it with a dynamic Crypto map on the side of Pix. Our questions are simply; is this the best solution? can change us the original static list or is it better to delete and make a new dynamic encryption card? Y at - it a shortcut to change the config command-line? This is a real network, so just check it out before make us any changes on the live kit.

  Any help much appreciated.

  You don't have to change anything when the peer-address changes. The dynamic crypto map aims to take dynamic peer connections. The only thing to remember, is that only the dynamic peer can initiate the connection. And you reduce your security if you use Pre-Shared key that now you can use a generic-PSK character.

  As I remember, the PIX / ASA does not support the dynamic use of FQDNs for peer-resolution. This feature is supported in IOS.

  For a feature, it would be preferable to static IP addresses on both sides.

• Doubt the implementation in a VPN between a VPN3005 and a Cisco 827 router

  Imagine this:

  Establish a VPN tunnel between the central administration (VPN3005) and a branch (827). Only need to spend intellectual property data in the tunnel and the two sites must reach the resources of the other, which means I don't want not just any what NAT involved.

  Can someone tell me what is the way to better/simple to do this?

  Can it be implemented with Cisco easy VPN? (or not, due to not wanting to make any type of NAT)

  Thanks in advance!

  Hello

  I would have preferred a VPN Tunnel from Lan to Lan. I have attached a few URLS that

  explains the implementation of IPSec Lan to Lan tunnel in different scenarios:

  1. with the router with a static routable ip address

  http://www.Cisco.com/warp/public/471/ALTIGAR.shtml

  2. with the router is assigned an IP via DHCP.

  http://www.Cisco.com/warp/public/471/vpn3k_iosdhcp.html

  Kind regards

  Arul

• tunnel from site to site between router IOS and ASA

  I've combed through the configs on both sides of this tunnel 4 x now and the look of policies as they match. I applied the http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080094498.shtml note

  My crypto lsits access are good and my nat on the side of IOS are provided with a map of the route and look good. On the SAA traffic side on the side of the remote tunnel ASA is exempt from NAT. Each side already has a site to another tunnel configuration, so I added the appropriate lines to the existing cryptographic cards which include peers, transform set and match address 'access-list. The polcies crypto isakmp on both ends are compatible. I have attached some configs and debugs (from router IOS), but essentially the newspaper on the SAA starts with the phase 1 is complete and then routing not received notification message, no proposal chosen readings and then it goes to IKE lost the connection to a remote peer, connection, drop table correlator counterpart has failed, no match, the deletion and finally disconnected session reason lost service.

  Their other tunnel stay standing as well as the configuration of remote access vpn connection is good.

  I found a note that recommends checking any access security-list, so I removed the, but no luck, and a Cisco associated with a hub, but had a healthy logic

  Is displayed normally with the

  Cisco VPN 3000 correspondent

  message hub: no proposal

  Chosen (14). This is a result of the

  being host-to-host connections.

  The configuration of the router has the

  IPSec proposals ordered so that the

  proposal selected for the router

  with the access list, but not the

  peer. The access list has a larger

  network including the host that

  a cutting traffic.

  Make the router for this proposal

  hub to router connection

  first in line, so that it corresponds to the

  specific to the host first.

  but that didn't work either.

  Thank you

  Bill

  Bill,

  Take a look at this

  000610: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): need XAUTH

  000611: * 10:42:15.094 PCTime sep 27: ISAKMP: node set 920927400 to CONF_XAUTH

  000612: * 27 sep 10:42:15.094 PCTime: ISAKMP/xauth: application XAUTH_USER_NAME_V2 attribute

  000613: * 27 sep 10:42:15.094 PCTime: ISAKMP/xauth: application XAUTH_USER_PASSWORD_V2 attribute

  000614: * 27 sep 10:42:15.094 PCTime: ISAKMP: (2039): launch peer 74.92.97.166 config. ID = 920927400

  000615: * 27 sep 10:42:15.094 PCTime: ISAKMP: (2039): lot of 74.92.97.166 sending peer_port my_port 4500 4500 (R) CONF_XAUTH

  -Other - 000616: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE

  000617: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): former State = new State IKE_P1_COMPLETE = IKE_XAUTH_REQ_SENT

  It should not go to extend the authentication. Since you have the client and the L2L on the same router and clients are configured for Extended authentication, the router will ask for XAUTH unless you configure the "No.-xauth" command after the pre-shared key

  Please implement the command:

  ISAKMP crypto keys in clear text address 74.92.97.166 No.-xauth

  Thank you

  Gilbert

• drop between mid-2009 and IOS device does not

  Mid 2009 Macbook Pro running El Capitan. Bluetooth and wifi on. When I opened Airdrop I see only the symbol of release with message "drop we will share you instantly... to share with someone using a Mac, ask them to go to Airdrop in the Finder. I don't see my IOS device on my Mackbook Pro, or I see my MackBook Pro on my IOS device in parachuting. Tech Genius Bar said that I had to add more storage for MacBook Pro. Made with a new SSD. Still not able to use Airdrop with IOS.

  It works as expected. Drop between iOS devices and Mac requires that the Mac is a 2012 model or newer.

  (140277)

• Suggestions of VPN for Windows 7 and ASA 5510

  We currently have a VPN solution with an ASA5510 and the client to the PC using the Cisco VPN Client V5.0.07.0410.  This works for Windows XP SP3 and Windows 7, however, Windows 7 will not allow enable start before logon or disconnect VPN connection when Logging Off (i.e. the Windows logon properties are missing in the client configuration options).  Is there a fix for this VPN client?  What VPN upgrade options available, which will allow these options?

  Thank you very much for your suggestions!

  You must use the AnyConnect client. I got on to start the same kind of project and purchased a license key AnyConnect, they are the easiest option.

  Sent by Cisco Support technique iPad App