Setup dma2100

Similar Questions

• DMA2100 cannot find network

  It is probably something easy. I just bought a DMA2100. I went through the routine of installation, including the configuration screen. When I get to network connection issues, choose wireless, then it goes in search for wireless networks screen - and crashes. No wireless networks are found, can not go backward or forward to the questioning, need to repower or reset the device again.

  I have a router Netgear Wireless G with WPA2 encryption. The router is only 10 feet of the DMA. I also disabled the encryption for a bit to see if this can help, but it didn't. And there are other networks in the region where he would have to see also, but it didn't, just hangs.

  Any ideas or suggestions?

  Larry

  As a final to this channel update, I found an ethernet cable just long enough for the DMA to the router. Then I went through the Setup routine using ethernet wired rather than wireless. Above all, I was hoping that some additional settings may be available or miracle.

  What happened, was that she did almost immediately an update of the firmware online. I have reset the device after, disconnected from the ethernet, then crossed the wireless configuration. It is immediately found my wireless network and about 10 others in the region.

  So I guess the firmware loaded with the device was somehow bad. Don't know how a wireless client can only update the firmware on this machine, but I got lucky.

  Larry

• DMA2100 reconnect to the VMC

  Just got a DMA2100. Implemented as an Extender, all worked fine (ish)!

  He tried the next day... get «pending for PC...» "then eventually times out. I ping the PC Media Center Extender so it seems that the Extender connects to the network OK.

  Only way to make it work again is to go through Setup again and it works OK until I tried again the next day.

  No firewall in my network and installed the latest firmware on the Extender. No message recorded in the event viewer on the PC after turning on the Extender on the PC that makes me think that the Extender is struggling to find the PC for some reason any.

  Any ideas?

  I think I've solved the problem. Some time back I enabled ICS get Bluetooth Internet access. Anyway, I tried to disable ICS on the NIC in the PC and now the Extender reconnects OK. Weird, but there you go!

  FYI, if others have this problem and find that there is no 'Sharing' tab under the properties of the network adapter that may be because ICS has been enabled with 2 network cards not configured but now there is only 1 network card installed. You can get it by installing another network card. I just installed the MS Loopback card which then allowed me to disable ICS on my Ethernet card. After that, I removed the loopback adapter.

• Apple Watch unlock Mac Setup Frustration

  I own a first generation of Apple Watch and an end 2013 13 "MacBook Pro and last mac mini (i5). I went through the entire setup process to have my watch unlock my MacBook several times. (All along the) When I get to choose the button "Allow your Apple Watch unlock your Mac", it runs for awhile and then I get the "unable to contact Apple Watch" fast. It seems to be my watch because if I try and let the Apple Watch locked, she'll tell me to unlock, and then try again. Happens on MacBook Pro and mac mini in the same way.

  I tried to research on this problem and we tried all authentication reset to two factors for an agreement again all settings and turn it on again.

  Any thoughts?

  Thank you!

  Hello pgirardi,

  I appreciate that you try to unlock your two computers using your Apple Watch with watch OS 3.  The resources below provide the steps and requirements to do this.  I would just try it with a single computer until you have a job before trying the second computer.

  Automatically unlock your Mac with your Apple Watch
  
  

  The first time you open a session after you turn on or restart your Mac, connect by entering your password manually. After that, Apple Watch connects to you.

  Set up automatic unlock

  Make sure your Apple Watch uses watch OS 3, and your Mac to mid-2013 or newer model uses macOS Sierra.
  For more information, see system requirements of continuity.

  Automatic unlocking

  Automatic unlock works with these devices and operating systems:

  watchOS 3	macOS Sierra
  Apple Watch (1st generation) Apple Watch series 1 Apple Watch series 2	MacBook (early 2015 or newer) MacBook Pro (late 2013 or newer) MacBook Air (mid-2013 or newer) Mac mini (late 2014 or newer) iMac (late 2013 or newer) Mac Pro (end of 2013 or later)

  Make sure your Apple ID to use instead of the two-step verification two factor authentication. Learn more.

  Make sure that your devices are configured as follows:

  • Your Mac has Bluetooth and Wi - Fi enabled.
  • Your Mac and Apple Watch are connected to iCloud with the same Apple ID.
    On your Mac, choose Apple () menu > System Preferences, and then click iCloud.
    On your iPhone, open the Apple Watch app, then go to general > Apple ID.
  • Your Apple Watch uses a password.
    On your iPhone, open the Apple Watch app, then type the access code.
  • Your Mac has "allow your Apple Watch unlock your Mac" selected in Security & Privacy preferences.
    Choose the Apple menu > System Preferences, click on Privacy & Security, then select the general tab.

    

  pgirardi, if you are unable to unlock your main computer after trying these steps, then you will need to cancel the match your iPhone and Apple Watch and try again.

  Cancel the match your iPhone and Apple Watch

  Take care.

• I have iphone5s and my contact id does not work, all the time he show faild Setup touch id please help?

  I have iphone5s and my contact id does not work, all the time he show faild Setup touch id please help?

  Hi yjain51,

  I understand you had some problems recently with getting Touch ID to work reliably on your iPhone 5s. I know that it is a feature of great security for your iPhone, so I'm happy to help you.

  When you use Touch ID, make sure that your hands are free of any dirt or moisture so that fingerprints can be read clearly. This article explains further:

  Use the ID Touch on iPhone and iPad - Apple Support

  Thank you for using communities Support from Apple. See you soon!

• Setup various AE advise

  I have problems to get the maximum speed. My ISP is 150 MB and I have this Setup:

  Airport Extreme (6th generation) placed in the living room connected to the Ethernet modem (modem is bridged, no router). When I connect this way, it gives me 130-150 MB, which is fine.

  However, when I connect these devices all starts to vary:

  1. an other Airport Extreme (6th generation) is connected to the hand on. Expansion of the network. When I try to change the option expand Network turn off this airport restarts but never succeeds and gives me an error. The only thing I can do is add then reset again and then I can only use the extension of the network. This normally works very well but do not know what it might cause the heavy fall.

  On this second AE Ethernet port I have attached a Synology NAS with my music, and so on

  2. an Airport Express (A1392 3rd gen) that I now set to join the network to see if things would improve. This one I use for music and it has a smart thermostat bridge (Tado) plugged into the Ethernet port

  3. an Airport Express (A1392 3rd gen) which I used to use to expand the wireless network but have disabled now I read that the extension of the network makes the slower WIFI and I'm afraid the Express slows down the extreme speed AC but not sure about that.

  4. a Time Capsule from Apple (4th gen) which I use for backup. I disabled the connection here as I believe join or extend the network would be to ask questions. I have attached a few devices through Ethernet at the back of the TC.

  The various airports are in different places in my house but not more then 10 meters (30 feet) on the other.

  That Setup would you recommend in order to get the best speed in different places?

  Thanks for the help!

  1. an other Airport Extreme (6th generation) is connected to the hand on. Expansion of the network.

  If you extend the network using a wireless connection between base stations, it will be the first performance issue you will encounter. It would be preferable to extend it using a wired connection between base stations. This is known as a roaming network configuration.

  2. an Airport Express (A1392 3rd gen) that I now set to join the network to see if things would improve. This one I use for music and it has a smart thermostat bridge (Tado) plugged into the Ethernet port

  In this configuration the AirPort Express performs like any other client wireless on your Wi - Fi network. He also performed an Ethernet bridge wireless for the Tado. It does not perform routing functions, or it extends the network. In addition, please note that the A1392 is a base station 2nd generation 802.11n. There is no 3rd generation... yet.

  3. an Airport Express (A1392 3rd gen) which I used to use to expand the wireless network but have disabled now I read that the extension of the network makes the slower WIFI and I'm afraid the Express slows down the extreme speed AC but not sure about that.

  Yes, what you read is correct. Again, you can reduce the amount of the penalty to performance of a network using a network of itinerant type instead. This requires not all base stations to be connected by Ethernet.

  4. a Time Capsule from Apple (4th gen) which I use for backup. I disabled the connection here as I believe join or extend the network would be to ask questions. I have attached a few devices through Ethernet at the back of the TC.

  How this time Capsule is connected? Wired or wireless and other base stations? For the record, it cannot be configured to 'join the AirPort Express wireless network'.

  The implementation of recommendation would be a roaming network.

• Why my audio midi Setup does not recognize my external midi devices?

  Why my audio midi Setup does not recognize my external midi devices? The midi interface and all midi devices are connected.

  P.S. The icons and the midi interface are all "grayed out" in the midi studio window when I click or double click on it nothing happens.

• the iTunes Setup program finishes, but the application does not appear

  For starters, I'm on Windows, but it seems that the system is not the problem because it's happened before, with my Macbook Air.

  I download iTunes on Apple's site and Setup will run as usual and finishes. But iTunes never displayed in Program Files, the destination he was supposed to have downloaded. I opened the Task Manager and tried to manually run the program yourself by using 'itunes.exe', but he writes that the application does not exist.

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  The more information box has direct links with the current and recent if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit - for older video cards) as a workaround for problems with installation or operation, or compatibility with third-party software.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• I tried several times to this update, but never a Setup program appears.  Why?

  Using a MacBook Air El Capitian 10.11.5 running and try to update to 10.11.6.  I tried to download the update several times, but never a Setup program.  Someone has an idea of what's going on?

  Try to run the update from the drop-down list. It installs all the previous updates plus a new one, which can replace all files that may have damaged.

  10.11.6 updating combo

• We have site and only works with Firefox 3.0 Setup. so, can we have this version Offline Installer?

  We have site and only works with Firefox 3.0 Setup. so, can we have this version Offline Installer?

  Why is your site, not be able to be consulted in current Firefox?

  Firefox 3.0 is now rather old and vulnerable.

  If you must use a version of Firefox 3.0.x for that one site then try the portable version of Firefox 3.0.12. English is near the bottom of the list.
  http://sourceforge.NET/projects/PortableApps/files/Mozilla Firefox 2% C Portable ed. / Mozilla Firefox Portable edition 3.0.12 %2C.

  ^ copy + paste the url above.

  Installs it portable Firefox is autonomous, that it does not touch your version of Firefox or normal profiles for her.

• I tried to install firefox.exe in silence, I used this command. @start/wait "Firefox Setup Stub 40.0.3.exe" - ms, but I encounter not found error - ms

  @ECHO.
  @ECHO Firefox installation
  @start/wait "Firefox Setup Stub 40.0.3.exe" - ms

  COR - el that it works! Thank you very much for the help!

  @Start/wait "Firefox" "Setup C:\TMP\Firefox 40.0.3.exe" - ms

• In one of my firefox browser, the header/footer margin setup parameter is inches, I need to change it to milimeter to inches. Your help is appreciated.

  In one of my firefox browser, the header/footer margin setup parameter is inches, I need to change it to milimeter to inches. Your help is appreciated.

  As far as I KNOW Firefox displays the metric or Imperial depending on the type of paper selected for printing. If you are using A4, you should get millimeters/metric.

• Create installation in silent mode with selections customized in installing Setup for a localized installation of firefox

  Hello

  So I need to create a setup package in silent mode to full firefox install that is here for Windows-> https://www.mozilla.org/en-US/firefox/all/?q=English%20 (US)

  I need to be able to select custom installation, settings, just like I would with the User Interface (select the radio button options)

  Can you help me to achieve this the simplest possible?

  Thank you

  Hello, you can disable the Import Wizard by placing a file override.ini with this content in firefox % INSTALLPATH%\browser\:

  [XRE]
  EnableProfileMigrator=false
  

  to preconfigure some settings in firefox, use the method described in http://kb.mozillazine.org/Locking_preferences. to disable the default browser promt and updates, put this in the mentioned .cfg file:

  //
  lockPref("browser.shell.checkDefaultBrowser", false);
  lockPref("app.update.enabled", false);
  

  https://developer.Mozilla.org/en-us/Firefox/Enterprise_deployment

• That means "bad connections" warning to the average of the Mail account setup?

  The Mail account setup dialog box, the works of autodetect IMAP, but after clicking "Done", a warning is displayed (see image), declaring "Thunderbird may allow you to get your mail using the supplied configurations." However, you must contact your administrator or your e-mail provider about these incorrect connections. See the Thunderbird FAQ for more information. ».
  I checked the Thunderbird FAQ (or what is the information that I found) but there is no explanation of this warning.

  On the connection used:

  -C' is a working IMAP with STARTTLS on port 143

  -the server is using a self-signed certificate (not expired), which Thunderbird complains not in the warning

  -with the help of a Setup from another existing SMTP account (no control in the Mail account setup dialog box)

  So I ask myself, what this warning is really all.
  Best regards

  Watch dialog box seems to occur only if:

  • There is an e-mail account, SMTP outgoing self-signed certificate
  • The new e-mail account uses the only existing outgoing SMTP Protocol

  This could be a default in Thunderbird 31.7.0, because there is only one such warning dialog to the configuration of the e-mail account that is used for reporting several different problems. The code (source Thunderbird: mailnews/base/prefs/content/accountcreation/emailWizard.js) power switches of the incoming and outgoing messages, but in this particular case, it seems to turn off all messages - which leaves just the text displayed in the screenshot - compare to https://support.mozilla.org/en-US/kb/server-doesn ' t-use-encryption

  When you use a new profile without all accounts in Thunderbird 31.7.0, new account creation work without such a warning.

• What is Firefox Setup Stub 38.0.exe? Said my worm. 37.0.2 needed

  I checked to determine if my plug-ins are updated and a message appeared saying that I was not running later
  version of Firefox. I am running version 37.0.2 and do not know what is this Firefox Setup Stub 38.0.exe, or why
  I would need.

  My FF, updated May 14 last version 38.0.1 also. There was no further reference to the Installer 'stub '. I consider that it is resolved, because apparently it was only once.

  Thanks to all who have posted answers to this question.