Several IPSEC VPN on SR 520

Similar Questions

• Configure several IPSec VPN between Cisco routers

  I would like to create multiple ipsec VPN between 3 routers. Before applying it, I would like to check on the config I wrote to see if it works. It's just on RouterA configuration for virtual private networks to RouterB, and RouterC.

  As you can apply in a cyptomap by interface, I say with the roadmap, that it should be able to manage traffic for both routers. Or is there a better way to do it?

  RouterA - 1.1.1.1

  RouterB - 2.2.2.2

  RouterC - 3.3.3.3

  RouterA

  crypto ISAKMP policy 10

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key RouterB address 2.2.2.2

  ISAKMP crypto keys RouterC address 3.3.3.3

  invalid-spi-recovery crypto ISAKMP

  ISAKMP crypto keepalive 5 10 periodicals

  ISAKMP crypto nat keepalive 30

  !

  life crypto ipsec security association seconds 28800

  !

  Crypto ipsec transform-set AES - SHA esp - aes 256 esp-sha-hmac

  !

  outsidemap 20 ipsec-isakmp crypto map

  defined peer 2.2.2.2

  game of transformation-AES-SHA

  match address 222

  outsidemap 30 ipsec-isakmp crypto map

  defined peer 3.3.3.3

  game of transformation-AES-SHA

  match address 333

  !

  interface GigabitEthernet0/0

  Description * Internet *.

  NAT outside IP

  outsidemap card crypto

  !

  interface GigabitEthernet0/1

  Description * LAN *.

  IP 1.1.1.1 255.255.255.0

  IP nat inside

  !

  IP nat inside source map route RouterA interface GigabitEthernet0/0 overload

  !

  access-list 222 allow ip 1.1.1.0 0.0.0.255 2.2.2.0 0.0.0.255

  access-list 223 deny ip 1.1.1.0 0.0.0.255 2.2.2.0 0.0.0.255

  access-list 223 allow ip 1.1.1.0 0.0.0.255 any

  access-list 333 allow ip 1.1.1.0 0.0.0.255 3.3.3.0 0.0.0.255

  access-list 334 deny ip 1.1.1.0 0.0.0.255 3.3.3.0 0.0.0.255

  access-list 334 allow ip 1.1.1.0 0.0.0.255 any

  !

  !

  RouterA route map permit 10

  corresponds to the IP 223 334

  Hi Chris,

  The two will remain active.

  The configuration you have is for several ste VPN site is not for the redundant VPN.

  The config for the redundant VPN is completely different allows so don't confuse is not with it.

  In the redundant VPN configuration both peers are defined in the same card encryption.

  Traffic that should be passed through the tunnel still depend on the access list, we call in the card encryption.

  This access-lsist is firstly cheked and as a result, the traffic is passed through the correct tunnel

  HTH!

  Concerning

  Regnier

  Please note all useful posts

• IPSec VPN to asa 5520

  Hello

  First I must admit that I am not very versed in Cisco equipment or in general IPSEC connections so my apologies if I'm doing something really good obviously stupid, but I checked through any kind of things that I could find on the internet on the configuration of IPSEC VPN.

  The setup I have is an asa 5520 (o/s 8.2) firewall which, for now, is connected to a temporary connection beautiful style home broadband for testing purposes. The netopia router is configured to allow ipsec passthrough and redirect 62515 UDP, TCP 10000, 4500 UDP, UDP 500 ports in the asa 5520.

  I'm trying to connein out of a laptop with disabled windows firewall and vpn cisco 5.0.02.0090 client version.

  I ran several attempts through the ipsec configuration wizard options. most of the time that nothing comes in the newspaper to show that a connection was attempted, but there is a way I can set up product options the following on the firewall log:

  4. Sep 24 2010 | 13: 54:29 | 713903 | Group = VPNtest9, IP = 86.44.x.x, error: cannot delete PeerTblEntry

  5: Sep 24 2010 | 13: 54:29 | 713902 | Group = VPNtest9, IP = 86.44.x.x, drop table homologous counterpart does not, no match!

  6. Sep 24 2010 | 13: 54:21 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:21 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:16 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:16 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:11 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:11 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  6. Sep 24 2010 | 13: 54:06 | 302015 | 86.44.x.x | 51905 | 192.168.0.27 | 500 | Built UDP inbound connection 7487 for Internet:86.44.x.x/51905 (86.44.x.x/51905) at identity:192.168.0.27/500 (192.168.0.27/500)

  and this, in the journal of customer:

  Cisco Systems VPN Client Version 5.0.02.0090

  Copyright (C) 1998-2007 Cisco Systems, Inc.. All rights reserved.

  Customer type: Windows, Windows NT

  Running: 5.1.2600 Service Pack 3

  24 13:54:08.250 24/09/10 Sev = Info/4 CM / 0 x 63100002

  Start the login process

  25 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100004

  Establish a secure connection

  26 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100024

  Attempt to connect with the server "213.94.x.x".

  27 13:54:08.437 24/09/10 Sev = Info/6 IKE/0x6300003B

  Attempts to establish a connection with 213.94.x.x.

  28 13:54:08.437 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 213.94.x.x

  29 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700008

  IPSec driver started successfully

  30 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  31 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  32 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  33 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  34 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  35 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  36 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  37 13:54:28.484 24/09/10 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  38 13:54:28.984 24/09/10 Sev = Info/4 IKE/0x6300004B

  IKE negotiation to throw HIS (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  39 13:54:28.984 24/09/10 Sev = Info/4 CM / 0 x 63100014

  Could not establish the Phase 1 SA with the server '213.94.x.x' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

  40 13:54:28.984 24/09/10 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  41 13:54:28.984 24/09/10 Sev = Info/6 CM / 0 x 63100046

  Set indicator established tunnel to register to 0.

  42 13:54:28.984 24/09/10 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  43 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  44 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  45 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  46 13:54:29.187 24/09/10 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  I have connectivity full http from the internet to a machine inside the asa 5520 so I think that the static routing and NAT'ing should be ok, but I am pleased to provide you with all the details.

  Can you see what I'm doing wrong?

  Thank you

  Sam

  Pls add the following policy:

  crypto ISAKMP policy 10

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  You can also run debug on the ASA:

  debugging cry isa

  debugging ipsec cry

  and retrieve debug output after trying to connect.

• Problem with IPsec VPN between ASA and router Cisco - ping is not response

  Hello

  I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):

  my network topology data:

  LAN 1 connect ASA - 1 (inside the LAN)

  PC - 10.0.1.3 255.255.255.0 10.0.1.1

  ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0

  -----------------------------------------------------------------

  ASA - 1 Connect (LAN outide) R1

  ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252

  R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252

  ---------------------------------------------------------------------

  R1 R2 to connect

  R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252

  R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252

  R2 for lan connection 2

  --------------------------------------------------------------------

  R2 to connect LAN2

  R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0

  PC - 10.0.2.3 255.255.255.0 10.0.2.1

  ASA configuration:

  1 GigabitEthernet interface
  nameif inside
  security-level 100
  IP 10.0.1.1 255.255.255.0
  no downtime
  interface GigabitEthernet 0
  nameif outside
  security-level 0
  IP 172.30.1.2 255.255.255.252
  no downtime
  Route outside 0.0.0.0 0.0.0.0 172.30.1.1

  ------------------------------------------------------------

  access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
  object obj LAN
  subnet 10.0.1.0 255.255.255.0
  object obj remote network
  10.0.2.0 subnet 255.255.255.0
  NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static

  -----------------------------------------------------------
  IKEv1 crypto policy 10
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 3600
  Crypto ikev1 allow outside
  crypto isakmp identity address

  ------------------------------------------------------------
  tunnel-group 172.30.2.2 type ipsec-l2l
  tunnel-group 172.30.2.2 ipsec-attributes
  IKEv1 pre-shared-key cisco123
  Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1

  -------------------------------------------------------------
  card crypto ASA1VPN 10 is the LAN1 to LAN2 address
  card crypto ASA1VPN 10 set peer 172.30.2.2
  card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
  card crypto ASA1VPN set 10 security-association life seconds 3600
  ASA1VPN interface card crypto outside

  R2 configuration:

  interface fastEthernet 0/0
  IP 10.0.2.1 255.255.255.0
  no downtime
  interface fastEthernet 0/1
  IP 172.30.2.2 255.255.255.252
  no downtime

  -----------------------------------------------------

  router RIP
  version 2
  Network 10.0.2.0
  network 172.30.2.0

  ------------------------------------------------------
  access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
  access-list 102 permit esp 172.30.1.2 host 172.30.2.2
  access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
  interface fastEthernet 0/1
  IP access-group 102 to

  ------------------------------------------------------
  crypto ISAKMP policy 110
  preshared authentication
  aes encryption
  sha hash
  Group 2
  life 42300

  ------------------------------------------------------
  ISAKMP crypto key cisco123 address 172.30.1.2

  -----------------------------------------------------
  Crypto ipsec transform-set esp - aes 128 R2TS

  ------------------------------------------------------

  access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255

  ------------------------------------------------------

  R2VPN 10 ipsec-isakmp crypto map
  match address 101
  defined by peer 172.30.1.2
  PFS Group1 Set
  R2TS transformation game
  86400 seconds, life of security association set
  interface fastEthernet 0/1
  card crypto R2VPN

  I don't know what the problem

  Thank you

  If the RIP is not absolutely necessary for you, try adding the default route to R2:

  IP route 0.0.0.0 0.0.0.0 172.16.2.1

  If you want to use RIP much, add permissions ACL 102:

  access-list 102 permit udp any any eq 520

• Can connect to the IPSec VPN, but can not see the internal network

  I have several users that can connect to our rooms of ussing IPSec VPN on a 5505. I have a user who can connect, but cannot see the internal network. This user is using DSL with a speedstream 4100. However, I have another user with the same configuration that can connect and see the internal network. Newspapers in ASDM show the link, but do not seem to show any errors trying to access internal. Any help will be greatly appreciated. Thank you, Bill.

  Add...

  ISAKMP nat-traversal crypto

• IPSec VPN connectivity between multiple subnet for the unique subnet

  Hello

  I have headquarters where several VLANs are running and branch has a subnet.following is subnet details

  Head office subnets

  192.168.0.0

  192.168.101.0

  192.168.50.0

  192.168.10.0

  192.168.20.0

  192.168.30.0 all are 24

  branch

  192.168.1.0/24

  Headquarters I have PIX and branch, I have cisco router 2600. I want my subnet all headquarters access to my office of general management of the LAN

  I want to create an ipsec vpn, my question is that I can combine several subnets of headquarters in a subnet because I want ot get rid of several ACL entries

  Hello

  Well, if we look at the site of the Directorate. He has only the single network and even with the destination network that overlap, it shouldn't be a problem. If a host on the network of agencies needs to connect to another host to local subnets will connect directly to him and the traffic flow through the router.

  I don't know if there should be no problem on the PIX side or the other.

  But to be honest, it's a very small amount of networks, and I don't see a particular reason, that I would not configure each network specifically, even if it should procude a few lines more to the ACL. Personally, I prefer to be as specific as possible in configurations to avoid any problems.

  -Jouni

• integrated macOS Sierra Cisco IPsec VPN does not work anymore (impossible to validate the server certificate)

  Hello

  I just upgraded to macOS Sierra and built-in Cisco IPsec VPN no longer works. When you try to connect, I get a "cannot validate the certificate of the server. "Check your settings and try to reconnect" error message. I use Cisco ASA with self-signed certificates and everything worked fine with previous versions of OS X.

  Please help me, I need my VPN Thx a lot

  I am having the same problem with StrongSwan and help cert signed with the channel to complete certificates included in the pkcs12 file imported to the keychain. It was working properly in El Capitan, but now broken in the Sierra.

• WRV200 ipsec VPN

  Hi guys,.

  Tried to set up an ipsec VPN LAN - LAN between my WRV200 and WRVS4400N my companion. Filled all the relevant config... simple... but still nothing. They don't seem to connect. We are both on ADSL and using IP address by DNS. Routers are in the log file and try to establish the connection. Tried all the setting, both routers are configured the same. STILL NO JOY! Can anyone help, before having to migrate to a netgear or something nasty!

  Sorry forgot to mention, using an AM200 modem in Bridge mode. It my router DHCP address direct WAN instead of NAT. The two systems are fixed the same where routers have outside the WAN address. The modem is transparent. I guess that NAT traversal in not required in that State.

• IPSec vpn - no selected proposal

  Hello:

  I am facing a problem in the configuration of the ipsec vpn on my 7200 router. It's a site to customer topology as shown below.

  

  The request from my pc, R2' isa crypto log:

  R2 #debug crypto isakmp
  Crypto ISAKMP debug is on
  R2 #.
  R2 #.
  R2 #.
  * 22:41:59.871 6 April: ISAKMP (0): received 66.66.66.52 packet dport 500 sport 500 SA NEW Global (N)
  * 22:41:59.879 6 April: ISAKMP: created a struct peer 66.66.66.52, peer port 500
  * 22:41:59.879 6 April: ISAKMP: new created position = 0x67E98D84 peer_handle = 0 x 80000002
  * 22:41:59.883 6 April: ISAKMP: lock struct 0x67E98D84, refcount 1 to peer crypto_isakmp_process_block
  * 22:41:59.887 6 April: ISAKMP: 500 local port, remote port 500
  * 22:41:59.891 6 April: ISAKMP: (0): insert his with his 67E5DCD8 = success
  * 22:41:59.911 6 April: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
  * 22:41:59.911 6 April: ISAKMP: (0): former State = new State IKE_READY = IKE_R_MM1

  * 6 April 22:41:59.931: ISAKMP: (0): treatment ITS payload. Message ID = 0
  * 6 April 22:41:59.935: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.939: ISAKMP: (0): IKE frag vendor processing id payload
  * 6 April 22:41:59.939: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.943: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
  * 22:41:59.947 6 April: ISAKMP (0): provider ID is NAT - T RFC 3947
  * 6 April 22:41:59.947: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.951: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
  * 6 April 22:41:59.955: ISAKMP: (0): provider ID is NAT - T v2
  * 6 April 22:41:59.959: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.959: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 194
  * 6 April 22:41:59.963: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.967: ISAKM
  R2 #P: (0): provider ID seems the unit/DPD but major incompatibility of 241
  * 6 April 22:41:59.971: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.971: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 184
  * 6 April 22:41:59.975: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:41:59.979: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 134
  * 22:41:59.983 6 April: ISAKMP: (0): pair found pre-shared key matching 66.66.66.52
  * 6 April 22:41:59.987: ISAKMP: (0): pre-shared key local found
  * 22:41:59.987 6 April: ISAKMP: analysis of the profiles for xauth...
  * 22:41:59.991 6 April: ISAKMP: (0): audit ISAKMP transform 1 against the policy of priority 10
  * 22:41:59.995 6 April: ISAKMP: AES - CBC encryption
  * 22:41:59.995 6 April: ISAKMP: keylength 256
  * 22:41:59.999 6 April: ISAKMP: SHA hash
  * 22:41:59.999 6 April: ISAKMP: unknown group of DH 20
  * 22:41:59.999 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.003 6 April: ISAKMP: type of life in seconds
  * 22:42:00.003 6 April: ISAKMP:
  R2 # life expectancy (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
  * 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
  * 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 2 against the policy of priority 10
  * 22:42:00.011 6 April: ISAKMP: AES - CBC encryption
  * 22:42:00.011 6 April: ISAKMP: keylength 128
  * 22:42:00.011 6 April: ISAKMP: SHA hash
  * 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group unknown 19
  * 22:42:00.011 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.011 6 April: ISAKMP: type of life in seconds
  * 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
  * 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
  * 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 3 against the policy of priority 10
  R2 #r 6 22:42:00.011: ISAKMP: AES - CBC encryption
  * 22:42:00.011 6 April: ISAKMP: keylength 256
  * 22:42:00.011 6 April: ISAKMP: SHA hash
  * 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group 14 unknown
  * 22:42:00.011 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.011 6 April: ISAKMP: type of life in seconds
  * 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.011 6 April: ISAKMP: (0): free encryption algorithm does not match policy.
  * 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
  * 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform 4 against the policy of priority 10
  * 22:42:00.011 6 April: ISAKMP: 3DES-CBC encryption
  * 22:42:00.011 6 April: ISAKMP: SHA hash
  * 22:42:00.011 6 April: ISAKMP: Diffie-Hellman group 14 unknown
  * 22:42:00.011 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.011 6 April: ISAKMP: type of life in seconds
  * 22:42:00.011 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.011 6 April: ISAKMP: (0): offered hash algorithm is
  R2 # does not match policy.
  * 22:42:00.011 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 3
  * 22:42:00.011 6 April: ISAKMP: (0): audit ISAKMP transform against the policy of priority 10 5
  * 22:42:00.011 6 April: ISAKMP: 3DES-CBC encryption
  * 22:42:00.011 6 April: ISAKMP: SHA hash
  * 22:42:00.011 6 April: ISAKMP: group by default 2
  * 22:42:00.011 6 April: ISAKMP: pre-shared key auth
  * 22:42:00.011 6 April: ISAKMP: type of life in seconds
  * 22:42:00.015 6 April: ISAKMP: life (IPV) 0 x 0 0 x 0 0 x 70 0x80
  * 22:42:00.019 6 April: ISAKMP: (0): offered hash algorithm does not match policy.
  * 22:42:00.023 6 April: ISAKMP: (0): atts are not acceptable. Next payload is 0
  * 22:42:00.023 6 April: ISAKMP: (0): no offer is accepted!
  * 6 April 22:42:00.027: ISAKMP: (0): phase 1 SA policy is not acceptable! (local 180.180.0.130 remote 66.66.66.52)
  * 22:42:00.027 6 April: ISAKMP (0): increment the count of errors on his, try 1 of 5: construct_fail_ag_init
  * 6 April 22:42:00.027: ISAKMP: (0): has no
  R2 #construct AG information message.
  * 6 April 22:42:00.027: ISAKMP: (0): lot of 66.66.66.52 sending my_port 500 peer_port 500 (R) MM_NO_STATE
  * 22:42:00.027 6 April: ISAKMP: (0): sending a packet IPv4 IKE.
  * 22:42:00.031 6 April: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 22:42:00.035 6 April: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (post 66.66.66.52)
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): IKE frag vendor processing id payload
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
  * 22:42:00.039 6 April: ISAKMP (0): provider ID is NAT - T RFC 3947
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID is NAT - T v2
  * 6 April 22:42:00.039: ISAKMP: (0)
  R2 #: load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 194
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 241
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 184
  * 6 April 22:42:00.039: ISAKMP: (0): load useful vendor id of treatment
  * 6 April 22:42:00.039: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 134
  * 22:42:00.039 6 April: ISAKMP (0): action of WSF returned the error: 2
  * 22:42:00.039 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
  * 22:42:00.039 6 April: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM1

  * 22:42:00.059 6 April: ISAKMP: (0): removal of reason HIS State "Policy of ITS phase 1 not accepted" (R) MM_NO_STATE (post 66.66.66.52)
  * 22:42:00.059 6 April: ISAKMP: unlock counterpart struct 0x67E98D84 for isadb_m
  R2 #ark_sa_deleted (), count 0
  * 22:42:00.067 6 April: ISAKMP: delete peer node by peer_reap for 66.66.66.52: 67E98D84
  * 22:42:00.071 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  * 22:42:00.075 6 April: ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_DEST_SA

  * 22:42:00.087 6 April: ISAKMP: (0): removal of HIS right State 'No reason' (R) MM_NO_STATE (post 66.66.66.52)
  * 22:42:00.087 6 April: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_ERROR
  * 22:42:00.087 6 April: ISAKMP: (0): former State = new State IKE_DEST_SA = IKE_DEST_SA

  * 22:42:00.895 6 April: ISAKMP (0): received 66.66.66.52 packet 500 Global 500 (R) sport dport MM_NO_STATE
  * 22:42:02.911 6 April: ISAKMP (0): received 66.66.66.52 packet 500 Global 500 (R) sport dport MM_NO_STATE
  R2 #.
  * 22:43:00.087 6 April: ISAKMP: (0): serving SA., his is 67E5DCD8, delme is 67E5DCD8
  R2 #.

  And when I capture on my pc, I got:

  

  I don't know why, waiting for you helps nicely, thank you very much!

  I think that what is wrong is your combination of your group of encryption, hashing and dh, try changing your sha instead of md5 hash table.

• Routing access to Internet through an IPSec VPN Tunnel

  Hello

  I installed a VPN IPSec tunnel for a friend's business. At his desk at home, I installed a Cisco SA520 and at it is remote from the site I have a Cisco RVS4000. The IPSec VPN tunnel works very well. The remote site, it can hit all of its workstations and peripheral. I configured the RVS4000 working in router mode as opposed to the bridge. In the Home Office subnet is 192.168.1.0/24 while the subnet to the remote site is 192.168.2.0/24. The SA520 is configured as Internet gateway for the headquarters to 192.168.1.1. The remote desktop has a gateway 192.168.2.1.

  I need to configure the remote site so that all Internet traffic will be routed via the Home Office. I have to make sure that whatever it is plugged into the Ethernet on the RVS4000 port will have its Internet traffic routed through the Internet connection on the SA520. Currently I can ping any device on the headquarters of the remote desktop, but I can't ping anything beyond the gateway (192.168.1.1) in the Home Office.

  Any help would be greatly appreciated.

  Thank you.

  Hi William, the rvs4000 does not support the tunnel or esp transfer wild-card.

• SA520 and Question IPSec VPN RVS4000

  Hello

  I installed an IPSec VPN for one of my friends for his company. At its principal office, I installed a Cisco SA520 and he uses to connect devices such as the iPhone and iPad via the IPSec VPN. He uses this fact because he travels abroad a lot and he has problems with services such as Skype is blocked in some countries. This configuration works very well.

  It also has a Cisco RVS4000, which he would like to install at his place of business to the Mexico. He would like the RVS4000 VPN configuration to the SA520 in his office. The SA520 in his office has a static IP address. The RVS4000 to the Mexico does not work.

  Is it possible to Setup IPSec VPN between a SA520 with a static IP and RVS4000 address that does not have a static IP address? If so, examples of configuration would be greatly appreciated.

  Thank you!

  Hi William, simply sign up for a dyndns account or similar service, the RVS4000 configuration will be the same, instead of the IP, you'd be using the dyndns name.

  -Tom
  Please mark replied messages useful

• Is availble for IPsec VPN FOS 6.3 support stateful failover

  Is availble for IPsec VPN FOS 6.3 support stateful failover

  SAJ

  Hello Saj,

  Unfortunately not... stateful failover replica information such as:

  Table of connection TCP, udp xlate table ports, h.323, PAT port allocation table...

  they replicate data such as:

  user authentication (uauth) table

  Table ISAKMP / IPSEC SA

  ARP table

  Routing information

  Therefore, in the case where the main breaks down, the IPSEC vpn will be reformed for the failover... Meanwhile, the user will not be able to access the applications...

  I hope this helps... all the best... the rate of responses if deemed useful...

  REDA

• ISA500 site by site ipsec VPN with Cisco IGR

  Hello

  I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.

  But without success.

  my config for openswan, just FYI, maybe not importand for this problem

  installation of config

  protostack = netkey

  nat_traversal = yes

  virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET

  nhelpers = 0

  Conn rz1

  IKEv2 = no

  type = tunnel

  left = % all

  leftsubnet=192.168.5.0/24

  right =.

  rightsourceip = 192.168.1.2

  rightsubnet=192.168.1.0/24

  Keylife 28800 = s

  ikelifetime 28800 = s

  keyingtries = 3

  AUTH = esp

  ESP = aes128-sha1

  KeyExchange = ike

  authby secret =

  start = auto

  IKE = aes128-sha1; modp1536

  dpdaction = redΘmarrer

  dpddelay = 30

  dpdtimeout = 60

  PFS = No.

  aggrmode = no

  Config Cisco 2821 for dynamic dialin:

  crypto ISAKMP policy 1

  BA aes

  sha hash

  preshared authentication

  Group 5

  lifetime 28800

  !

  card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1

  !

  access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255

  !

  Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac

  crypto dynamic-map DYNMAP_1 1

  game of transformation-ESP-AES-SHA1

  match address 102

  !

  ISAKMP crypto key address 0.0.0.0 0.0.0.0

  ISAKMP crypto keepalive 30 periodicals

  !

  life crypto ipsec security association seconds 28800

  !

  interface GigabitEthernet0/0.4002

  card crypto CMAP_1

  !

  I tried ISA550 a config with the same constelations, but without suggesting.

  Anyone has the same problem?

  And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?

  I can successfully establish a tunnel between openswan linux server and the isa550.

  Patrick,

  as you can see on newspapers, the software behind ISA is also OpenSWAN

  I have a facility with a 892 SRI running which should be the same as your 29erxx.

  Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.

  Here is my setup, with roardwarrior AND 2, site 2 site.

  session of crypto consignment

  logging crypto ezvpn

  !

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  lifetime 28800

  !

  crypto ISAKMP policy 2

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  lifetime 28800

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 4

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  !

  crypto ISAKMP policy 5

  BA 3des

  preshared authentication

  Group 2

  life 7200

  ISAKMP crypto address XXXX XXXXX No.-xauth key

  XXXX XXXX No.-xauth address isakmp encryption key

  !

  ISAKMP crypto client configuration group by default

  key XXXX

  DNS XXXX

  default pool

  ACL easyvpn_client_routes

  PFS

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT

  !

  dynamic-map crypto VPN 20

  game of transformation-FEAT

  market arriere-route

  !

  !

  card crypto client VPN authentication list by default

  card crypto VPN isakmp authorization list by default

  crypto map VPN client configuration address respond

  10 VPN ipsec-isakmp crypto map

  Description of VPN - 1

  defined peer XXX

  game of transformation-FEAT

  match the address internal_networks_ipsec

  11 VPN ipsec-isakmp crypto map

  VPN-2 description

  defined peer XXX

  game of transformation-FEAT

  PFS group2 Set

  match the address internal_networks_ipsec2

  card crypto 20-isakmp dynamic VPN ipsec VPN

  !

  !

  Michael

  Please note all useful posts

• Problem with IPSec VPN ISA500 & login questions (multiple devices)

  I have a Cisco ISA500, we use for connection with IPSEC VPN of some products apple (MacBook Pro and iPad). We can operate randomly once in a while, but it fails most of the time of negotiation. Someone at - it suggestions on what I can do to make this work?

  I did test it on my Linux machine and it does not when I had configured default settings. I had to change the NAT Traversal for UDP CISCO on the Linux machine for the connection to work.

  14/04/03 20:54:13 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
  2014-04-03 20:54:13 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: max number of retransmissions (2) reached STATE_AGGR_R1. (pluto)
  2014-04-03 20:53:30 - warning - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: quick mode attempt fails, please check if IKE/transformation/PFS local are the same as remote site; (pluto)
  2014-04-03 20:53:30 - warning - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: max number of retransmissions (2) reached STATE_AGGR_R1. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: STATE_AGGR_R1: sent AR1, expected AI2.; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = 'groupname' [48] XXX.XXX.XXX.XXX #59: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [Dead Peer Detection]; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: regardless of the payload of unknown Vendor ID [16f6ca16e4a4066d83821a0f0aeaa862]; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02] Vendor ID = 107, but already using method 109; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02_n] Vendor ID = 106, but already using method 109; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received meth payload [draft-ietf-ipsec-nat-t-ike-03] Vendor ID = 108, but already using method 109; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received Vendor ID value = 109 payload [RFC 3947] method; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [Cisco-Unity]; (pluto)
  2014-04-03 20:53:03 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:43810 package: received vendor ID payload [XAUTH]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: STATE_AGGR_R1: sent AR1, expected AI2.; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = 'groupname' [47] XXX.XXX.XXX.XXX #58: attribute OAKLEY_KEY_LENGTH not preceded by the OAKLEY_ENCRYPTION_ALGORITHM attribute.  Attribute OAKLEY_KEY_LENGTH. (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [Dead Peer Detection]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: regardless of the payload of unknown Vendor ID [16f6ca16e4a4066d83821a0f0aeaa862]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02] Vendor ID = 107, but already using method 109; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-02_n] Vendor ID = 106, but already using method 109; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received meth payload [draft-ietf-ipsec-nat-t-ike-03] Vendor ID = 108, but already using method 109; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received Vendor ID value = 109 payload [RFC 3947] method; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [Cisco-Unity]; (pluto)
  2014-04-03 20:52:20 - WARNING - IPsec VPN: msg = XXX.XXX.XXX.XXX:58320 package: received vendor ID payload [XAUTH]; (pluto)

  Hi rich,

  What version of firmware you used before upgrade?  You upgrade to 1.2.19 and now this works?

  Thank you

  Brandon

• Router Cisco 1941 - crypto isakmp policy command missing - IPSEC VPN

  Hi all

  I was looking around and I can't find the command 'crypto isakmp policy' on this router Cisco 1941.  I wanted to just a regular Lan IPSEC to surprise and Lan installation tunnel, the command isn't here.  Have I not IOS bad? I thought that a picture of K9 would do the trick.

  Any suggestions are appreciated

  That's what I get:

  Router (config) #crypto?
  CA Certification Authority
  main activities key long-term
  public key PKI components

  SEE THE WORM

  Cisco IOS software, software C1900 (C1900-UNIVERSALK9-M), Version 15.0 (1) M2, VERSION of the SOFTWARE (fc2)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2010 by Cisco Systems, Inc.
  Updated Thursday, March 10, 10 22:27 by prod_rel_team

  ROM: System Bootstrap, Version 15.0 M6 (1r), RELEASE SOFTWARE (fc1)

  The availability of router is 52 minutes
  System returned to ROM by reload at 02:43:40 UTC Thursday, April 21, 2011
  System image file is "flash0:c1900 - universalk9-mz.» Spa. 150 - 1.M2.bin.
  Last reload type: normal charging
  Reload last reason: reload command

  This product contains cryptographic features...

  Cisco CISCO1941/K9 (revision 1.0) with 487424K / 36864K bytes of memory.
  Card processor ID FTX142281F4
  2 gigabit Ethernet interfaces
  2 interfaces Serial (sync/async)
  Configuration of DRAM is 64 bits wide with disabled parity.
  255K bytes of non-volatile configuration memory.
  254464K bytes of system CompactFlash ATA 0 (read/write)

  License info:

  License IDU:

  -------------------------------------------------
  Device SN # PID
  -------------------------------------------------
  * 0 FTX142281F4 CISCO1941/K9

  Technology for the Module package license information: "c1900".

  ----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  -----------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  security, none none none
  given none none none

  Configuration register is 0 x 2102

  You need get the license of security feature to configure the IPSec VPN.

  Currently, you have 'none' for the security feature:

  ----------------------------------------------------------------
  Technology-technology-package technology
  Course Type next reboot
  -----------------------------------------------------------------
  IPBase ipbasek9 ipbasek9 Permanent
  security, none none none
  given none none none

  Here is the information about the licenses on router 1900 series:

  http://www.Cisco.com/en/us/partner/docs/routers/access/1900/hardware/installation/guide/Software_Licenses.html