Several problems with my Satellite A200-1QZ

Similar Questions

• Strange problem with my Satellite A200

  Hello

  I have a problem with my Satellite A200-1DY.

  In the last two days, this occurs twice. When I start the laptop there are three icons, systray, speaker, battery and network icon, and then, the laptop stops and does not work. I can't use the mouse or keyboard and the cooler fan does not work.

  When I put my hand the area where it is the processor it is hot enough. I can't reset the laptop. At first I have to disconnect from the mains. After that I restart the laptop. The cooler fan starts very quickly and it removes a lot of heat from the CPU area.

  What can I do?
  Sorry for my horrible English and marry Christmas.

  Hello

  At first, I must say that your English is very good and understandable. Now after this compliment go back to the problem described. ;)

  I have too many Satellite A200 and I installed Vista and Windows XP Home edition, several times and never noticed a similar problem. I must say that all my tests were with the own operating system preinstalled.

  In your case, it is not easy to say why this happens, but it turns out that some process must be loaded and at this stage of the computer cell blocks. Usually, if you keep the Start button / stop for 5 seconds, book it should be OFF.

  You must understand that no one knows we what's your personal operating system configuration and if there are some applications you have installed the last days. Exact an application that runs in the background may not be loaded properly and blocks for laptop.

  What should do? You can enter MSCONFIG and check all entries of Systemstart. Try to disable all the stuff, you don't need and try it again. Maybe you will be lucky and find out if there is something that starting cell blocks.

  Sorry, but it's really not possible to say why this happen. If you want you can try to roll back the OS to an earlier time until it starts in the hope that the BONE will be work as before.

  Bye and good luck!

• Several problems with the Satellite A100-569

  Hello comrades toshers :)

  I had a portable 569 a100 in one last catalog can, last month he had to go off for repairs as the continuous screen empty and had to use the power button to shut it down and reboot again, also questions of excessive paging as well as my computer screen with a kind of mini earthquake... then it is gone and back a week and I these problems are still produce , I understand they have installed a new hard drive and a printed circuit board.

  I also noticed that I can't get the toshiba updates more about expansion memory... this laptop is not yet one year old so would appreciate any help this forum may be able to give me.

  I would sound Toshiba first thing tomorrow on the laptop being faulty, also the ease of online security does not recognize my serial number? very strange.

  long live the people

  Hello

  Obviously your laptop, one of the first models comes with the Vista operating system. To be honest, I agree with you on the RAM. 512 MB is certainly not enough. 1 GB is OK, but for me not enough. I recommend you to upgrade the RAM with 2 x 1 GB module. With 2 GB will be the laptop works well.

  The compatible RAM 1 GB module has PA3411U-2M1G part number. Use this number in Google and you'll find enough shops where you can order online.

  Good bye

• Problem with the Satellite A200 and Windows Vista startup

  Yesterday, my laptop had some mistakes and tried to stop.
  He remained on the screen closed for quite a long time, so I decided to push the power button until it turns off.

  When I went to turn it back to the a started going through the normal screens, the Toshiba screen and then the white screen with the Microsoft flag down. At this point, the screen goes completely black and rest that way.

  Through starting initial power cord, light is turned on, the power supply is on the HARD drive light and then when the screen turns white HARD drive light turns off and stays off.

  I tried to do a system repair using the F8 key at startup and it goes into the Advanced Boot Options menu when I select 'Repair your computer', the light of the HARD drive temporarily, I go through the screens and select System Restore, I selected a date a few weeks and then click Next on the screen indicating the (c :)) system disk is ready to be restored then it returns an error -" (c) drive has errors. Windows has detected corruption in the file (c) system.

  You should check the drive for errors before you can restore it "- and at this point, I can only click on the 'check' the drive to find errors, and then click Start, as he chose the option 'Automatically fix file system errors'."

  When I click Start nothing seems to happen just on the same screen, the HARD drive light does not come on at all and there is no internal HARD drive noise. The only way I can get out of this screen is to turn the computer off again.

  If someone is able to help I would really appreciate it!

  Thank you!

  Hi Cazza68,

  Looks like Windows is confused upward

  Can you start Windows if you perform an installation of Toshiba Recovery disk recovery?

• Several problems with Satellite A100

  Hello

  I was wondering if someone could point me in the right direction with regard to the fixing of my computer!

  I have supply problems with my Satellite A100 laptop that I bought in europe 2 years ago. When the battery is run-down completely the computer will not run / start at all when it is plugged into the wall. It shows a light indicating that the battery is in charge even the domain controller in the light does not appear. The laptop must load for at least 1-2 hours before I can activate it. Push the power button to the computer also turn on / off the light sometimes. I can't use the computer at all until the same fully charged battery if light shows it is plugged into the wall. The outlet is fine.

  I also have other issues. First of all the computer not as to the rename files - often said that they are used, but they are not. Secondly, I have problems with toshiba recordnow cd / dvd burning program. I can open the program, but when I close it will not open until I have sign out and then sign back in. Thirdly, my computer love is no longer my sony digital camera memory cards if put directlt in laptop - it is said that they can be dangerous and will not access.

  Thanks for reading!
  Shona

  PS my laptop does not at all depend on when the battery is removed and the laptop plugged into the wall.

  PPS. my laptop model is Satellite A100 - 163, PSAA9E model number

  Hello

  regarding your power problem:

  It seems that your motherboard is faulty. I had the same issue with an A100 and after replacing the motherboard, the problem has been resolved. They told me it was a kind of resistance or something as preventing the machine from power.

  The question of the name change is only registry related since the registry controls the access to the system. So you log on with an administrator account or with a regular account that was created for do not connect as an administrator of the computer?

  If not please google for "cannot rename files" that gives results much more then ask someone here. The registry could also be a cause for the issuance of recordnow!

  I Don t think that the card of your digital camera and your pc Don t like. Installed antivirus software? This might also be the reason.

  In your case, I suggest to bring your machine to an ASP (authorized service provider) and allow them to perform some checkup and proofreading materials.
  Back up your important data, and then perform a full restore of your machine (can be done with the recovery media supplied).

  See you soon

• Satellite A200-1QZ - view suddenly becames fuzzy and a little green

  Hello

  Excuse my bad English, but I have a problem with my 2 month old Satellite A200 - 1QZ Notebook.

  Sometimes, about 2 times a week, my screen get is fuzzy (there looks like the color depth would change to 16-bit or less) and I can see a small green tint (but here? not sure m) on the entire screen.
  I do not understand why, because sometimes during games, chat, write in word or something else, so no matter what I do.

  Currently AI? using m for laptops modified Desktop Driver Catalyst 08.2 (the driver is original, but I have a tool called 'Mobility DotNET4', I modified with.

  I don't think that the updated driver is the reason for my problem, because I remember of the day, I used the notebook for the first time and 1 hour later, I got it too. And now, the certified Toshiba display driver has been installed.

  I solve the problem with the restart of the system, but it is very uncomfortable during the games or chatting.

  I hope that my text is understandable...

  Help, I would be very grateful.

  Welcome MatthiasV

  Hello

  Eventually he s a graphics card problem, it is possible if the 3rd party graphics card driver has been installed.
  The graphic drivers from Toshiba support thermal protection which is needed to prevent overheating of the material!

  If you have used a non-Toshiba driver then a GPU could overheat and therefore this issue happened.

  However, for me, it looks like a hardware problem and therefore the laptop must be checked by a service provider authorized in your country!

  Good bye

• Satellite A200-1QZ: No. HARD drive during the installation of XP

  HIII,

  I have a problem!
  I have my laptop (satellite A200-1QZ) buythis for everyday, it is with Windows Vista: (((I don't like it!

  I download driver xp for any material!
  I would like to install Win XP SP2 cd boot but it's error message, when I access the installation,< harddisk="" can't="" found="">>!

  I think that the mistake is on the SATA - HARDDISK? orrrr

  Please help me: p
  and happy new year...

  You must install the Intel Matrix Storage Manager first.

  This issue has been described many times here in the forum.

  I would really recommend to use the advanced search option forum, if you need details ;)

  Best regards and happy new year friend

• Problems with disk Satellite pro 4200 hard assembly

  I have problems with a Satellite pro 4200.
  The Notbook reads no more disks. Undercarriage I traded the loan, but did not work. Undercarriage is addressed, but it is read the discs is not possible or formatted. Also, an update of the Bios is not possible, as undercarriage reads no more disks.

  CU
  Eltgen

  Hi Eltgen

  Sorry, but it is not easy to tell what the problem is on that path. If I understand you well you have built in a new floppy drive, because the old one was faulty. Am I wrong?

  It will be interesting to know is the new part already used. Perhaps is the new one also defective. I hope that a little light is on if you put the disc inside.

• Problem with my Satellite C650D - 10 d of charge

  I have some problems with my Satellite C650D - 10 d and its battery.

  Indeed, when I want to reload my computer, it will no more, charge his battery to 99%, then it says "Blocked, not supported" and the corresponding light is off instead of orange or yellow-green.

  Then, after using my computer on battery, if I want to load, plug is not enough, I must remove my battery and replace. Charges of battery, 99%, once again.

  The problem is recurring and I don't know what to do anymore. I tried to get an empty using the BIOS battery (because Windows 7 turns off the computer when the battery is at least 5%), to see if there was a problem of calibration of the battery, but this isn't the case, and my problem is still the same.

  Hope you can help me ;)

  I recommend the update to the BIOS.

  Not sure if the solution in your case, but I read in some discussions that the BIOS update could solve battery problems.

  Otherwise if the BIOS does not help, then you should check if the new battery could be the solution.

• Several problems with Windows 8 - Upgrade-unable to download full

  Original title: several problems with Windows 8

  Last Sunday, after downloading Ab2word, my tiles shortcuts stop working. I have uninstalled the program, but nothing improved. I made an update of Dell and got the shortcuts work again (curiously I could always connect via the desktop). now, I get a message saying that Windows is disabled and to enable him, by putting in... but he says that it is impossible to activate. Then I tried the upgrade to 8.1 by the store and got a message saying that I was unable to complete the download. Now my shortcuts tiled work, but they open the sites registered by the office, not as a full screen. I tried to restore to the factory and now get the message that the system is unable to restore. I ran a dell diagnostic and it showed nothing. I did a full security scan and he came clean. I'm rapidly reaching crisis. When you try to seek help on the Web site, Windows 8 is not listed... It is 7 to 8. 1. any suggestions? This computer is less than 2 years old and I'm ready to take a hammer to it.

  Hello David,.

  Please write to us and offering the opportunity to help Microsoft Community.

  What exactly do you mean when you say "Windows is disabled and enable it via the setting..."?

  You receive the "Cannot download" error during upgrade to Windows 8.1, I'll follow the steps by David Williams Dixon in the Blog below.

  Something happened and the 8.1 Windows installation may not be completed. (And now you are bored)

  We know if the steps help you in upgrading the computer to Windows 8.1.

• Several problems with ODT 12.1.0.1.2

  I've noticed several problems with ODT 12.1.0.1.2
  

  
  1 opening problem on the XE database packages (10.2).
  Problem occurs in Visual Studio 2010 and 2012.

  In Server Explorer, I created the data using ODP.NET connection, unmanaged pilot. in the 10.2 XE database

  When the connection is open tree of object type is displayed.

  Try opening the packages tree does not work ORA-00904: #SELTAB ".". OBJECT_TYPE': invalid identifier

  Same problem occurs using unmanaged driver.

  This does not happen to the standard database connection.

  2. the problem of schema comparison
  It does not work if XE (10.2) database is involved as a source or target.

  It fails with ORA-00904: "AP". "' OBJECT_TYPE ': invalid identifier

  3 connection editor

  There is an annoying problem with the connection editor.

  When I try to change the connection and the connection type is TNS then Data source name combobox selects the first entry of TNS (in alphabetical order) and not one that was used when the connection is created or changed.

  akabook wrote:

  I've noticed several problems with ODT 12.1.0.1.2
  

  
  1 opening problem on the XE database packages (10.2).
  Problem occurs in Visual Studio 2010 and 2012.

  In Server Explorer, I created the data using ODP.NET connection, unmanaged pilot. in the 10.2 XE database

  When the connection is open tree of object type is displayed.

  Try opening fails tree packages with ORA-00904: #SELTAB ".". OBJECT_TYPE': invalid identifier

  Same problem occurs using unmanaged driver.

  This does not happen to the standard database connection.

  2. the problem of schema comparison
  It does not work if XE (10.2) database is involved as a source or target.

  It fails with ORA-00904: "AP". "' OBJECT_TYPE ': invalid identifier

  3 connection editor

  There is an annoying problem with the connection editor.

  When I try to change the connection and the connection type is TNS then Data source name combobox selects the first entry of TNS (in alphabetical order) and not one that was used when the connection is created or changed.

  Thanks for the comments.

  (1) ODT requires database 10.2.0.3 or later since the view ALL_PROCEDURES added the OBJECT_TYPE column after this version. Now, everyone with the exception of 10.2 XE has updated past this point (XE cannot be corrected). So that means 10.2 XE cannot be used with ODT, if you want to view the proceedings. There is a 11.2 XE you can use:

  http://www.Oracle.com/technetwork/database/database-technologies/Express-Edition/downloads/index.html

  (2) same question

  (3) thanks for this note. I will alert you of the development team.

• Several problems with photoshop after upgrading to win10

  I've updated to win 10 a week ago and today I experienced several problems with photoshop. The first question is about the quick selection tool. I select and try to choose an area on the picture I want to work on. It performs either one of two things. F1. It won't select anything finally photoshop will crash. 2 when he decided to select something it goes super slow and will switch to the symbol of thought every few seconds.

  second question...

  Because I can't get select quick took the job I'll move the pen tool. I started to select anchor points and ill get maybe 20 points the image then becomes completely black. If I scroll top down I can clearly see the parts of the image, but when I stop scrolling returned to a black square. Later photoshop then crash.  TSF is to face all of a sudden?

  Make sure that your GPU drivers are perfectly up-to-date (directly from the manufacturer) and they are 10 Windows compatible. You can also try a reset preference:

  Win: Press and hold the keys Ctrl + Alt + Shift immediately after the launch of Photoshop starting. A box will appear asking if you want to continue with the reset, select 'yes '. If you don't see this, you're not fast enough... Try again.

  Benjamin

• Several problems with Adobe Creative cloud app.

  I have several problems with the Adobe Creative Cloud application.

  1 CC Photoshop or prelude CC cross the bar of the 47% during installation. They constantly give me messages "Installation failed". When I click on "Learn more", I like that:

  "Installation failed."

  Errors during Installation. (7)

  More information"

  So, naturally, I click on more information to get the lifting against me following (which no do I understand):

  Exit Code: 7 Please see specific errors below for troubleshooting. For example,  ERROR:   -------------------------------------- Summary --------------------------------------  - 0 fatal error(s), 2 error(s)    ERROR: 12/01/13 13:16:06:425 | [INFO] |  | OOBE | DE |  |  |  | 6076 | ---------- CustomHook_Helperx64 ---- Start ----------  12/01/13 13:16:06:426 | [ERROR] |  | OOBE | DE |  |  |  | 6076 | Cannot load function name 'CSInstallerCustomHookProc' from library C:\Program Files (x86)\Common Files\Adobe\Installers\uninstall\{5F816B76-62F3-41C9-B651-27F49F25F50B}.data. Error 0    ERROR: System check returned with error : -4  ------------------------------------------------------------------------------------- 

  2. I installed 5 Lightroom, then uninstalled. When I went back to re - install, the application Adobe Creative cloud wouldn't let me. He says that my 5 Lightroom is "up-to-date" and that it is in my article 'Your applications', not in the section 'find new applications '. I rechecked my programs and features in Control Panel, and it isn't here. I cleaned my registry and it is still there. I deleted the file "opm.db" in my OOBE folder and restarted CC - still nothing.

  I must say, guys. I'm not very happy with the time I spent just trying to install programs on my PC. While the plan is for it to be intuitive at a certain time, it is not very functional at the moment. No matter how much help you can provide me would be amazing - if you can provide it sooner than later, I'd be on the moon.

  Thank you.

  Hope this will help others record the amount of time this error I spent troubleshooting.  When you install Adobe InCopy CC, CC of Adobe InDesign, Adobe Photoshop CC, CC prelude Adobe and Adobe first Pro CC on a laptop Windows Pro 8.1, I an error similar to the one below.  Other installations of Adobe Acrobat XI Pro, Adobe affect effects CC, Adobe Audition CC, Adobe Bridge CC, CC of Adobe Illustrator, Adobe Lightroom 5 and Adobe SpeedGrade CC installed without error.  I ran across this test with a clean operating system, new construction to help isolate the problem.

  23/12/13 16:33:04:372 | [INFO] |  | OOBE. OF |  |  |  | 912 | 23/12/13 16:33:03:368 | [ERROR] |  | OOBE. OF |  |  |  | 6316 | Cannot load the name "CSInstallerCustomHookProc" C:\Program Files (x 86) library function \Common Files\Adobe\Installers\uninstall\{5F816B76-62F3-41C9-B651-27F49F25F50B}.data. Error 0

  I ran a minimum load of the operating system by stopping all non Microsoft services by running MSCONFIG. EXE and disabling and disabling all startup in the Task Manager, Startup tab items.  After restarting the laptop, I was then able to install CC of Adobe Photoshop and Adobe first Pro CC.  However, Adobe InCopy CC, CC of Adobe InDesign and Adobe prelude always failed CC.  I needed to start safe mode and disable BitDefender Virus Shield and BitDefender Desktop Update Service and then restart mode Normal (services were always disabled). I continued and completed the installations of Adobe InCopy CC, CC of Adobe InDesign and Adobe prelude CC.

  It seems that BitDefender is the process to load this function as a virus Trojan markup and stop installation.

• Problems with its Satellite A100 and professional cards

  Hi all

  I bought an A100 Satellite less than a year ago and have had problems with 2 different business cards when using Cubase.

  -M-Audio firewire solo plugged into the TI PCMCIA card
  -Echo Indigo io (PCMCIA card)

  I am running Windows XP and Cubase SE/SX3. When running Cubase, there are cracks, the sound stops for a few milliseconds.

  I've never had any problems with my old Toshiba laptop Satellite Pro A40. It's very disappointing and frustrating. I use my new Toshiba for the Internet!

  Could someone help?

  See you soon,.
  Fred

  Hello

  This has been discussed in several topics, so please visit the following positions and get something for yourself:

  This one has a driver and registry solution:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=18720

  But first, I recommend you to read this one:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=18631

  It s long, so be prepared to read a lot. Hope you can solve your problem.

  Concerning

• Problem with my Satellite C870

  I have a problem with my toshiba satellite C870. The noise stopped working. the sound icon is cut and I got a message: no speakers or headset is connected. I tried corrections but I thought that my driver is up to date. For accuracy I am under W7. Sorry if my English is bad (I speak french, but you can answer me in English)

  Thks

  Hello

  Reach:
  Panel of-> sound-> the Read tab

  You see your speakers or headphones here?
  If so, make sure that the speakers are marked as the default device.

  In addition the combination FN + F11 would turn on and off MUTE.
  Check it!

  When two solutions of workaround don t help, uninstall the device high definition audio / controller as well as the audio driver from the Device Manager and restart the computer laptop n.
  After restarting again the system should install the uninstalled drivers even more often, this will help you to get the sound.