Several switches inside the a test sequence

Similar Questions

• Help: Configure the simple test sequence, operator selects particular test connects to the part of the teststand sequence file and then performs the test

  Hello

  I am very new to TestStand, please see the question below and give advice.

  I want to set up a simple test sequence.

  I want a message to popup on the screen that asks the operator what unit of 6 units (maximum 10) to test (i.e. There is say box of 6 to 10 s to select from).

  Then the sequence goes to the specific part of the sequence and performs the test on a unit that either has been selected.

  What is the best way to do it?

  I use pop-up message windows to do this? and if so what should I connect to the correct part of the sequence file?

  Pop-up message windows allow only 6 options to select from?

  Thank you

  Hello

  You can do this by using the method of message popup. You can ask the user what unit want to run message by inserting in the expression of the message in the message popup step parameters. Something like below

  "Enter the number of execution unit.

  1 Unit1

  2 unit 2

  .......

  10 Unit 10 "

  then check the 'Enable response text box"tab is different from the stage. When the user enters the unit number you can get the value entered by the user by inserting the below statement post expression of message popup step parameters

  Locals.String = Step.Result.Response

  Note: The string is a local variable to be set.

  Convert string to number and send that output to pass the expression you can use a sequence of call step to call the sequence according to which must be performed. (I hope your each unit will file separate sequence)

  I hope that this solves your problem. If you do not understand please let me know so that I can put a small example and send it to.

  See you soon,.

  Krishna

• Throw after error while using the switch inside the ProductLookup... ?

  Hi all
  
  When you use droplet of switch with release of ProductLookup droplets, throws following error...
  
  code-
  
  < name dsp:droplet = "/ atg/commerce/catalog/ProductLookup" >
  < name = 'elementName' value 'product' = dsp:param / >
  < name dsp:param = 'id' param = "productId" / >
  < name dsp:oparam = "output" >
  Product is new? -param = "product.new" dsp:valueof / >-here it gives false... but the error happens when you use droplets of switch
  < name dsp:droplet = "/ atg/dynamo/drop/Switch" >
  < name dsp:param = "value" value = "true" >
  < name dsp:oparam = "false" >
  This product is not new
  < / dsp:oparam >
  < dsp:oparam name = "true" >
  This product is new
  < / dsp:oparam >
  < / dsp:droplet >
  < / dsp:oparam >
  < / dsp:droplet >
  
  
  errorMessage-
  
  
  2012-11-29 19:44:54, ERROR 312 [org.apache.catalina.core.ContainerBase. [JBoss.Web]. [localhost]. [chi]. [jsp]] Servlet.Service () for servlet jsp threw exception
  org.apache.jasper.JasperException: product/inc/product_inventory.jsp(96,3) according to the TLD, dsp:param of the tag must be empty, but is not
  
  
  
  Thanks in advance,
  Laurie Bovilla
  
  Published by: Laurie B on 29 November 2012 06:22

  You should do like this in the drop of switch:

  
  
  
  
  Product is new? - -Here is giving fake... but the error happens when you use droplets of switch
  
  **
  
  This product is not new
  
  
  This product is new
  
  
  
  

• keyboard shortcuts to switch to the next sequence and zoom

  Hello World video editors!
  
  More I work with Premiere Pro, the more I like it. There is one thing that annoys me tho, I can't assign two shortcuts:

  1. I would like to be able to use ctrl-tab to switch to the next sequence open (down time)
     Ideally, also SHIFT ctrl tab to switch to the previous open sequence
  2. I wish I could use cmd - and cmd + to zoom in and out of my calendar. (do not larger or smaller lines)
     

  Anyone?

  Thank you!

  Sebastian Dahl

  Hello

  To switch between the tabs of the sequence, you can use SHIFT + 3 .

  And = - to zoom out and zoom in.

  Thank you

  Mohd. Naseem

• How to place a video inside the title sequence?

  I use CS6.

  I am fairly new home, but I'm trying to place a video inside the main title sequence so that when the sequence is played as a whole, there is a miniature video playing in the top corner following titles still in view.

  I hope that I am clear about that and I apologize if I'm not.

  Any help is appreciated.

  Its called picture in picture (PIP)

  http://www.InfiniteSkills.com/demos/movie-player.php?h=685&w=890&movie=http://iSkills-Medi a.s3.amazonaws.com/premierecs5-demo/0707.mp4

• Position of the bitmap inside the BitmapField

  Hi, this is perhaps a silly question, but is at - there a way for me to specify the position of the bitmap image to add inside the BitmapField?

  I already added the bitmapfield to the screen and I want to add several bitmaps inside the field, but in certain specified places. Is it possible to do this without changing the location of bitmapfield?

  Help, please!

  Hi thanks for the reply! Creation of absolutefieldmanager seems quite complicated and a lot of work!

  I found a way to achieve what I needed treatment multiple paint.drawBitmap!

  Thanks for the help!

• Button "Exit", used in several images of the sequence

  I hope that there is a more elegant way to do...

  See the VI attached for a much simplified program that is typical of what I am trying to accomplish.  Basically I have a button that I want available in several images in the sequence.  In this case, I used a button "quit".  When you press on, the program passes by remaining sequence frames until it ends.  The last image "unclicks" the button "Exit".  This last image is necessary because I had to put the mechanical action of the Exit button for "switch when released" because I used local variables in all the images in the sequence after the first.

  Is there a way I can accomplish the same functionality of this program without using local variables and/or during the definition of the mechanical action of the 'exit' switch to ' lock releasing?  Specifically, I'm looking for solutions that will work in several images of a structure of stacked sequence (I realized there are ways for the three lights without using a structure of stacked sequence, but I'm not interested in doing).

  Any help would be greatly appreciated!  Thank you!

  Something where you're looking at a sequence of steps, you really recommended using a state machine architecture.  (Search the forums for examples).

  Having several structures event with cases duplicated in different settings of a structure of stacked sequence (it would be a little better if you used a structure rather flat sequence), only to request trouble on the road.

• How to use &lt; C:when test... inside the column in the table of the ADF

  I use ADF table with two columns
  in the first column, I check the Type of document is doc type so I have to use commondlink to download this file, otherwise I need to display only text.
  
  to this I added
  * < c:when test = "{boolean ($favoriteType eq 'doc')}" > *.
  that does not work.
  
  Please let me know how to use < C:when test... inside the column in the table of the ADF
  
  < tr:column sortProperty = "favoriteName" sortable = "true".
  headerText = "#{res ['favorite.favoritename ']}" "
  width = "500" noWrap = "false" >
  < c: choose >
  * < c:when test = "{boolean ($favoriteType eq 'doc')}" > *.
  < tr:commandLink actionListener = "#{bindings.downloadFile.execute} '"
  Text = "#{row.favoriteName} '"
  Disabled = "#{!}" Bindings.downloadFile.Enabled}"/ >
  < / c:when >
  < c: otherwise >
  < af:outputText value = "#{row.favoriteName}" / >
  < / c: otherwise >
  < / c: choose >
  < / tr:column >
  < tr:column sortProperty = "favoriteType" sortable = "true".
  headerText = "#{res ['favorite.favoriteType ']} ' rendering ="true">"
  < af:outputText value = "#{row.favoriteType}" id = "favoriteType" / > "
  < / tr:column >

  Hello

  I do not see, you use a Table of the ADF, but I see that you use Apache Trinidad. JSTL is executed analysis of time then that JSF is to render time, that's why it does not work what you see. Trinidad is a part of tr:switcher, and you can try this. Note that it doesn't ' r allow to change components by rank.

  Frank

• Can I quote the 'switch' inside my router?

  I hope there is a way to name the 'switch' in my router so that it shows up as anything other than "unknown" in my network card in Windows. Is this possible? Or maybe just a way to make it appear differently in Windows 7, as to change the icon to something other than a question mark? I ask not how the router itself, maned I wondering how to add a name to the switches inside in the Windows network mapping. It would be nice if it was still just "port 2" "port 3" etc.

  You can not

• Why the total time required for the test sequence is different during the test runs

  Hello

  -J' have different test resources to test our product which includes engines and the NOR-Box (6351).

  -Number of test files in sequence that are called during the test (ca. 20)

  -The problem is that when I run these test sequence files separate (say only 3 out of 20), total time by these tests are t1, t2 and t3, but when - I left all 20 tests to run without jumping all the time needed by the 3 tests above is t1 + 60 s, t2 + 80 s and t3 + 50sec. Why it is so and how can I avoid this problem.

  -The tests are motors to move, take samples or box then save them on my computer after testing the limits. Since they are time critical, when I do all the running tests in a test go a lot do not PASS. I can't run them separately because it takes more time, more interference by user and also more than one report that is not desired.

  -J' tried unloading after execution steps, but it did not help.

  Kind regards

  RB

  This probably depends on that made your sequence. Have you tried shrink where extra time is being spent? You can time how long different parts of your sequence are following the steps of the expression as follows:

  Locals.StartTime = Seconds()

  Locals.ElapsedTime = Seconds() - Locals.starttime

  You can also watch time module in your reports. There is nothing specific on TestStand that should cause some sort of slow down like this. I recommend trying to figure out where the extra time is being spent. I suspect once you do, the cause will become obvious.

  -Doug

• Sequence structure flat inside the timed loop and execution order

  I have some problems trying to implement a flat sequence structure when you use a loop timed on a target of cRio VI

  I tried with or without the while loop around the structure of sequence flat, and I also tried to replace the 'Non-deterministic loop' with a timed loop

  The problem is that the program seems to run only once, then get stuck somewhere

  I am writing a program that performs the following operations as soon as possible:
  1. read the Pos_MC of entry on the FPGA
  2 send the value of Pos_MC to the VI target (on cRio CPU)
  3. calculate a value of output based on Pos_MC with a PID block ("exit PID')
  4. send 'PID output' to the FPGA
  5 write "PID output" analog output "MOOG".

  In addition, I want the program to return the measured value "Pos_MC" to a host VI for the recording of data

  So that the output of PID is calculated and sent to the FPGA as quickly as possible, I placed a flat sequence structure to ensure that it happens before you send the output to the nondeterministic loop for recording data

  Also, I want the digital input 'Stop' to be able to stop the loop deterministic (the timed loop)

  I read much more entries than that and the help of several PID and exit, but I rewrote the code for a single entry and exit to make it easier to illustrate

  Screenshot of the code is shown in 'target code.png' and 'fpga code.png.

  The VI themselves are attached in the next post (cannot attach files of more than 3)

  Question 1:
  Any advice on how to get this race? Thank you!

  Question 2:
  Is also my correct understanding in that, using this structure, each 0.9ms (fpga loop time) comes the following:
  1. the input ("Pos_MOOG") is read on the fpga
  2. the production of PID is calculated on the cRio with some delay to computation (for example 0.1ms)
  3. the output of PID is then written for analog output "MOOG" in all about 0, 1 - 0.2ms
  4. the FPGA program then waits until 0.9ms spent and repeat the process

  As opposed to the next pass whenever performing a loop is started on the FPGA:

  1. the FPGA reads the input and written on the output (the output of the execution of the previous loop PID)

  2. then the entry is sent the cRio, PID output is calculated and sent to the FPGA

  3. the new release of PID is maintained until the next time through the loop

  Thank you!

  PHG wrote:

  Thanks for the input guys, any advice as to how I could get the feature in scenario 1?

  I still say that the best route is just putting all the logic of the control in the FPGA.

  Other alternatives include 1) the use of DMA FIFO sedn data back or 2) use interruptions so that the FPGA code can not read the output level until the RT.

  DMA FIFOs are usually very limited, and I would not use them in this situation since I belive said it this code to do for the many outputs.

• Only AAS, 2 inside the kernel switches (HSRP) Best Practice Design

  Hello

  I design a N/W with following equipment.

  1: 2 * carrots (4503)

  2: single Firewall ASA 5520

  I have following design options;

  DRAWING 1:

  1. Basic switches use HSRP
  2. VLANs are active on a (primary) switch at a time
  3. CONNECT THE TWO CŒURS WITH ASA
  • ASA E0 - outside (routers) switch
  • ASA (redundant interface = E1 + E3) R1 - the two nuclei (HSRP)
  • ASA E1 - Core 1 (F3/48) + ASA E3 - Core 2 (F3/48)
  • ASA E2 - switch DMZ

  DESIGN 2:

  1. Basic switches use HSRP
  2. VLANs are active on a (primary) switch at a time
  3. CONNECT THE TWO CŒURS FOR LAYER 2 SWITCH (INNER AREA)
  4. CONNECT THE LAYER 2 SWITCH TO ASA E1

  The first options looks better avoid me point single failure (Layer 2 of insdie switch).

  Unfortunately, I'm short on time and do not currently have access to the LAB.

  Please

  1. Share your experience and suggest which option is preferable
  2. Advantages, disadvantages during the failover hsrp, other features, etc.
  3. indicate if there is an alternate option
  4. Precautions

  BR,

  ABDUL MAJID KHAN

  Your "redundant ASA interface" is not really. Only one ASA has no real redundancy. I guess you could make a "inside the 1" and "inside 2", but they would have separate IP addresses and within hosts would not automatically from one to the other. " I would say that the complexity that introduced more than offset the second idea to have a small switch L2 VLAN between your ASA unique within the interface and your L3 core switches.

  That's why I prefer the second option. A switch L2 deemed unchanged configuration being done is quite reliable - I regularly fall on them with years of availability. You can also add a quasi redundancy in option 2 by tying together your ASA E1 interfaces and E3 in an etherchannel (requires a Software ASA 8.4 or later version). that option is not possible with option 1 (at least not in the two basic switches) as an Etherchannel are two IOS switches at one end.

• Hi, I really need help... I can't find any broadcasting EBU-100/75, test your 1 KhZ, etc... I m going to do 15 masters short for Swedish broadcasting channel at night. -haha! and I can't find anything inside the first... I m I'm blind! Help, please! Vanle

  Hi, I really need help... I can't find any broadcasting EBU-100/75, test your 1 KhZ, etc... I m going to do 15 masters short for Swedish broadcasting channel at night. -haha! and I can't find anything inside the first... I m I'm blind! Help, please! Paris looks Jokum

  Bay3Bob - you are great! Thanxxx :-)

• How to use a function switch box to the reference that is used several times in the previous drop-down list options?

  I use JavaScript coding in LiveCycle and development of dependent drop-down areas, but I find it difficult to write correct code. See the example below. I'm trying to use a multiple box function that refers to an option that is listed several times in the previous pull-down menu. The problem I am running into is that when I refer to any color or Nissan and Chevy, it returns the results of the color in the "Ford" column only. I'll always see color (blue, black, green and purple) options in my second drop-down list and it seems fine, but then the third drop reference only the options and colors 'Ford '. (I don't have the code for the third menu list drop-down).

  I want the client to choose Chevy or Nissan and have her drop downs (based on the color they chose)-dependent, but I can't seem to make this work.

  I hope it is clear enough (probably as mud...). I would appreciate help!

  Form1. #subform [0]. #subform [1]. cboModels::exit - (JavaScript, client)

  cboColor.clearItems ();

  {Switch (this.) RawValue)}

  case "Ford":

  cboColor.addItem ("Blue");

  cboColor.addItem ("Black");

  cboColor.addItem ("Green");

  cboColor.addItem ("Purple");

  break;

  case 'Chevy ':

  cboColor.addItem ("Blue");

  cboColor.addItem ("Black");

  cboColor.addItem ("Green");

  cboColor.addItem ("Purple");

  break;

  case "Nissan":

  cboColor.addItem ("Blue");

  cboColor.addItem ("Black");

  cboColor.addItem ("Green");

  cboColor.addItem ("Purple");

  break;

  }

  Form1. #subform [0]. #subform [1]. cboColor::exit - (JavaScript, client)

  cboPrice.clearItems ();

  {Switch (this.) RawValue)}

  case "Ford":

  case "green":

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  break;

  case 'Chevy ':

  case "green":

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  break;

  case "Nissan":

  case "green":

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  cboPrice.addItem ("blah");

  break;

  }

  You can use '\n' for newline in a string, so

  "Option 1, \nOption 2, \nOption 3;

  Put each on its own line.

  Bruce

• How to invoke actionlistener inside the af:switcher element

  Hi guys,.

  I'm working on Jdeveloper 11.1.1.6 and I have this situation: a selectOneChoice component that shows a particular aspect of an element of switching, and inside this facets, there are a few commandButton with Actionlistener. This id code:

  < af:selectOneChoice value = "#{requestScope.panel}" autoSubmit = "true" valuePassThru = "true" > "

  < f: selectItems value = "#{backingBeanScope.Bean.List}" id = "si2" / > "

  < / af:selectOneChoice >

  
  

  < af:switcher id = 's2' facetName = "#{requestScope.panel}" >

  < f: facet name = "FACET1" >

  < af:commandButton id = actionListener = "#{backingBeanScope.Bean.Btn_actionListener"cb1"} ' / > "

  < / f: facet >

  < / af:switcher >

  The problem is that the actionlistener the command button does not work. How can I solve this problem?

  Thank you!

  Hello

  There is another problem with your code (next to the realization by dvohra21). Select only one value is saved in a scope of application memory, which means that it is not persisted beyond application. The scope should be at least viewScope.

  Frank