SG300 and RVS4000 DHCP problems

Similar Questions

• WLC and Linksys DHCP problem

  Hello

  I have a WLC 2112 and a DHCP Server enabled on a Linksys router. I set up a wireless LAn to have the IP address of the Linksys DHCP server, but it does not work and when I configure the DHCP anthor server it works.

  Can you help me please

  Your controller cannot ping the LinkSys Router? In addition, you set up the DHCP server on the interface of the controller, correct?

• SG300-20 - configure DHCP on the interface VLAN

  I have read the different partners of the discussions on the SG300 and SG500 going on regarding the high setting of VLAN and DHCP on VIRTUAL networks.  For some reason, I could not get even this simple task to work.

  First thing I did was update my version firmware and boot as follows:

  SW version 1.3.7.18 (date of 12 January 2014 time 18:02:59)

  Start the 1.3.5.06 version (dated 21 July 2013 times 15:12:10)

  HW version V02

  When I rebooted the SG300 after the SW/Boot updates the boot configuration has been crushed and I had to configure my switch from scratch.  The intention is to have two VIRTUAL networks:

  VLAN 1: all the devices, servers, etc.

  VLAN 2: subnet basis which distributes DHCP addresses

  The SG300-20 is connected to a router Asus RT-AC66U on the 192.168.1.x subnet and provides access to the internal network and WiFi access (IP address of the router is 192.168.1.1 and the default gateway).  Everything works without any problem.  So my task is simply to create 2 VLANS on 192.168.2.x subnet and use DHCP to assign addresses.  I spent many hours on it and I still can't get it to work.  When I connect a laptop to the port (GI8) assigned to 2 VLANS, I end up finding a few wobbly 169.254.x.x address.  I definitely thought something would not 'easy' that hard to set up, but apparently I was wrong.

  The SG300 is running in mode L3 as shown in my running-config below.

  Someone gets to see something which could prevent my client from the laptop to receive the interface VLAN 2 DHCP IP addresses that are not on the 192.168.2.x subnet?

  Any ideas / suggestions would be greatly appreciated!

  Here's my running-config:

  config-file-header
  MYSTICSW1
  v1.3.7.18 / R750_NIK_1_35_647_358
  CLI v1.0
  router adjustment system mode

  SSD of encrypted file indicator
  @
  SSD-control-start
  config of SSD
  control of password file unrestricted SSD
  no control of the integrity of the file ssd
  SSD-control-end cb0a3fdb1f3a1af4e4430033719968c0
  !
  database of VLAN
  VLAN 2
  output
  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
  Add a voice vlan Yes-table 00036 b Cisco_phone___
  Add a voice vlan Yes-table 00096e Avaya___
  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
  Add a voice vlan Yes-table 00d01e Pingtel_phone___
  VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075
  Add a voice vlan Yes-table 00e0bb 3Com_phone___
  Hello interface range vlan 1
  hostname MYSTICSW1
  host 192.168.1.15 record
  logging source hostname id
  username privilege 15 b4a0fcf20b2cd9d80a55b06ab8f83277f9733904 encrypted password cisco
  location of the SNMP-Server Office
  clock timezone ""-5
  DST Web recurring U.S. clock.
  clock source sntp
  unicast SNTP client enable
  unicast SNTP client survey
  survey of 192.168.1.10 SNTP server
  !
  interface vlan 1
  IP 192.168.1.254 255.255.255.0
  no ip address dhcp
  !
  interface vlan 2
  name MysticWAN
  192.168.2.254 IP address 255.255.255.0
  !
  interface gigabitethernet8
  switchport mode access
  switchport access vlan 2
  !
  output
  Default IP gateway 192.168.1.1

  Thanks in advance!

  Clint Lambert

  Clint, please see this post

  https://supportforums.Cisco.com/message/4178990#4178990

  -Tom
  Please mark replied messages useful
  http://blogs.Cisco.com/smallbusiness/

• Using 3500 as a Wireless Extender DHCP problem iPhone X 6

  Hello

  If all goes well, a simple question with a simple answer.

  Background:
  I stayed away from my DSL provider to a cable provider (VirginMedia). My new ISP is delivered with a modem cable (SuperHub 2 ac) and I connected the two devices together to extend my wireless home network. The cable modem, it's that the two routers are physically apart from others - connected through just their Ethernet ports - the technology of power line (Devolo dLAN 1200 +). Both routers have the same SSID broadcast, but on separate channels.

  Question:
  All devices in my house, the tablets of laptops, phones roam between the two areas wi - fi transparently * except * the iPhone 6 (iOS8.1), this works on the cable modem wi - fi, but not on the X 3500 wireless. I also have an iPad Mini 2 (also iOS8.1) which works too - aptly / wrong I have excluded iO8.1 as the issue. Oddly enough, the iPhone 6 connects to the x 3500 but isn't getting an IP address (the cable modem's DHCP server). Even if a static IP address doesn't help.

  Comments:
  If the X 3500 is configured as a DHCP server, the iPhoen connects (and gets an IP address), but then the default gateway is incorrect (gateway IP address of the X 3500 is not the modem cable remote). I can't find anywhere to specify a default gateway configuration.

  Question
  I start thinking, it is a problem with the iPhone 6 (know all other devices work correctly), but I want to just make sure I am the X 3500 configuration correctly. I am particularly interested in it if I use the right to 'Mode' ADSL / Ethernet. I tried 'Bridged Mode Only' (ADSL) and "Automatic DHCP only" (Ethernet), but does not seem to solve the problem of having the iPhone 6.

  any suggestions on how to fix / help would be most welcomed.

  Thank you!

  Thanks a lot for the details... Now I have a config that works also for the iPhone6.

  Basically, I connected the cable on the 3500 x port and the Ethernet port on the cable modem connected to the internet (via the Powerline). I then changed the network on the 3500 of 192.168.0.x x range (this is the range of network addresses used by the cable modem connected to the internet) to 192.168.168.x. Finally I activated the DHCP on the x 3500 which seemed to be the element that was killing the iPhone6.

  The iPhone6 connects now (which he always did), but with DHCP running on the x 3500 on the new range of network addresses of the iPhone 6 also get a valid IP address.

  Looks like that much just to get the iPhone 6 to work... never found a manual way to specify a default on the x 3500 gateway when you run DHCP (appears by default which is her own IP address - with no provision to change).

  Anyway... This works for now... I'll keep an eye on the iPhoen updates 6, just in case where the anomaly is something specific to the iPhone 6, if something changes I will post here.

  I have attached a picture for furture reference. Thanks again for your advice and support.

  

• Load firefox 3.6.14 and now can't access the internet. Computer restored to the previous version works now. 3.6.14 I tried again and the same problem, any ideas?

  Using windows 7. As soon as the update of firefox, I can not access Internet. I tried Internet Explorer works well. I have restored the previous computer Firefox and it works fine. Tried the update again and the same problem can not access the internet.

  This is usually caused by a firewall blocking the new version of Firefox. For more information, see https://support.mozilla.com/kb/Cannot+connect+after+upgrading+Firefox

• Performance on the Web access and the certificate problem arises

  Hello! I just bought a HP pro 8610 office jet and I'm trying to access the Scan function to access Web but performance is very slow and I just get a blank screen, no certificate appears.   I tried to do it in Chrome and Firefox.  Otherwise, the printer works fine.

  I accidentally entered a wrong email as beneficiaries on the address book and need to delete an entry via the Scan option in the Web.

  I'm on Windows 7 Edition home premium.

  Please advise, thank you!

  This has been resolved! Apparently the connection was slow for some reason any.  Just tried again this morning and the certificate that is presented and not more problems.  Thank you!

• Re: Qosmio G30 and green screen problem

  Dear friends

  I thing is interesting for any owner of Qosmio to look at this:

  http://www.asklaptopfreak.com/laptop-notebook-help/2007/07/08/Toshiba-Qosmio-G30-screen-problem/comment-page-4/#comment-130784

  http://www.asklaptopfreak.com/laptop-notebook-help/2007/07/08/Toshiba-Qosmio-G30-screen-problem/

  My Qosmio G30 is already dead, I got an estimate from the official service, to repair my qosmio costs nearly 600 pounds. Is a design flaw. Go on the internet.

  Interesting links! Thank you.
  I have to say then I must be lucky. My Qosmio G30 (German model) works well and without any problems

• Satellite A210-1AP - battery and power supply problem

  A few weeks ago I received my laptop (Satellite A210) reapair and the motherboard was changed.

  Since then, I got problem with the battery when it is inside and power cable is pluged.
  When the cable is in the laptop running on battery power I do not know why. Then when I turn it off battery led is lit Orange and the battery is charging.
  When the PC is turned on, the indicator light does not work and the battery becomes lower.

  So I wonder what the problem is.
  I read somewhere that this problem could solve the BIOS update.
  So anyone have experience like this.
  Also how is installed BIOS, I saw there is an installer for windows (so I guess it isn't hard).

  And somehow can back up old BIOS so I can go back if something bad happens.

  > A few weeks I got my laptop (Satellite A210) reapair and the motherboard was changed.
  > Since then, I had problem with the battery when it is inside and power cable is pluged.

  In my opinion, the technician has done something wrong
  The point is that this problem occurs after the exchange of motherboard and I think what this is about.

  Contact the ASP who repaired the laptop and explain your problem.
  I doubt that a BIOS update would solve this problem. I think it s a question an electrician

• Photon: Dropped calls and network connectivity problems

  I bought my Photon August 18 and he was not long for me first to the problems with network connectivity.

  The phone displays signal on the phone, but when you try to call, send text messages or surf the web. Zilch.

  A soft reset works every time. I've had some experience with the issue of the "appeal of ghosts", but had no network connectivity so often that he was too much a problem. Restores the soft 3-4 per day.

  I took the phone to the Sprint store and they told me that my phone verified and were not hardware problems that may be found. I said at the time on the update of the software of MR5 and was anxious to see how the phone after the update.

  I received the update on Wednesday and the phone worked fine. No appeal of ghost, no network connectivity not problems, only dropped the call.

  Now, Friday morning, I lost network connectivity despite seeing the strength of the signal and had to perform a soft reset to regain connectivity. My wife and I bought this phone at the same time. She had many calls interrupted before the update and we both experienced after that update eventhough signal showing on the phone is at least two if not more bars.

  Is this a known issue? Is it going to be/CAN this be corrected by a software update? Is this phone a lemon and he'll remember?

  I LOVE this phone. I don't want to get rid of it, but...

  Seriously. It's a phone! Making calls should be the FIRST thing that is done right.

  Please, someone, Motorola, reassure me that this isn't a lemon and that network problems are going to be fixed. I CAN wait, but I don't want to get stuck with two phones for $200 that need to be pampered just to be usable.

  Thank you

  TC

  Yes, it turns out that be was a buggy phone. Two stores tested Sprint phone for reception of the signal and they said that it spent; but as said the technician in the second store, the tests they take place the phone in ideal conditions.

  The two stores I've visited, said they were ready to replace the phone, but my first visit came just before the MR5 update software while I was willing to wait to see if the update corrects the problem. It didn't, but the replacement of the second store phone works fine with upgrading to MR5 and really no problem.

  I'll go ahead and mark this question as a response, but if you experience the same problems of chance complete loss of all network connectivity (Sprint or otherwise), I recommend getting the phone replaced. It is a bad camera.

  Oh and the technician at the second store mentioned the network problems. It has been a problem for them, but the most telling proof of the issue of network is random dropped calls. So if from time to time, you lose a call under the conditions of good network signal, it's probably not your phone and Sprint. I have almost that many abandoned calls as of late, so it could have been the wrong phone I had that really amplified the problem... or... Sprint has got some of the bugs in our region.

  Thank you for looking in. I hope that your problems are as easy to solve as mine and I hope that you are still within your 30 days so that you get a new replacement.

  Best wishes

  TC

• Satellite L30-134 - LAN and audio driver problem

  I installed the LAN driver but my internet is not working and I have problem whit my sound. I can't make it work in the speakers.

  Hi Smike_de,

  I think that no one can offer a solution to your problems because information and a more detailed description of the error are missing.

  What operating system you are using?
  Are you running the factory settings?
  Have you tried reinstalling the drivers?

  You can try to update the drivers. You can download it on the Toshiba site.

• My whatsapp necessary updated and I had problems making inturn I reset everything on the iphone5 he says my whatsapp was purchased and download free of charge despite being there download it still only downloads help please

  My whatsapp necessary updated and I had problems making inturn I reset everything on the iphone5 it says my whatsapp was purchased and download free of charge despite being there download it still only downloads help please what should I do

  Look for its requirements.

  I remember something similar happening to a friend of mine, but the sound of it, your phone can be updated. Aka what stop app works with earlier versions.

  But search for it in the app store to see its requirements! It will tell you!

• I use an analog input on a PCI-6224 and are having problems with the clock source

  I use an analog input on a PCI-6224 and are having problems with the clock source. I'm trying samples of 16 different analog inputs very quickly. I have the sample mode: Timed Single Point material. The rate, that I am running is the maximum (250 kHz (15625Hz per channel)). I left the default clock source and trying to taste several times. The analogue input works for a short time (2-3 seconds) and then everything stops. I'm doing something wrong or is there something I'm missing? Any advice would be great.

  That's how you samples using the sample clock clock. If you see a delay then something is wrong with how you track/data visualization.

  Single point NI the hardware is for PID control with a real-time operating system.

• Please give me solution for my computer always view your computer have persist order check and solve the problem every time when I open my computer.

  When I start my system the output display poster always your computer have Persist modula order check and solve the Problem.How to solve this problem

  Permanently?

  Hello

  
  What operating system is installed on the computer?
  
  Update video drivers and see if the problem persists.
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly
   
  Note: install the drivers on the manufacturer's Web site
  
  Hope this information helps.

• Blue and black screen problem

  I have the blue and black screen problem. I want to format my C drive, but he said no, that you can not format this drive. I know that I have Virus problem also and I want to format anyway. Please help me.

  Thank you

  Hello

  ·         What operating system do you use?

  ·         You get the error message?

  ·         You are able to boot to the desktop?

  Method 1:

  I also suggest you to download and run the latest Microsoft Scanner on your computer and check to see if it helps:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: the data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.

   

   

  Method 2:

   

  Why my screen is black when I start Windows 7?

  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

   

   

  Method 3:

  Resolve stop (blue screen) error in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

• Telephone calls from a man saying that he worked for Microsoft and he had problems in my area

  A man rang today saying that he worked for microsoft and he had problems in my area and if I turned on my computer it will help solve the problem. ???

  It was an international call, but I said that I had not reported any problems. What is going on???

  Relatively new user to the computer

  Hello

  Its a SCAM!

  In the United States, you can contact the FBI, Attorney general, the police authorities and consumer
  Watch groups. Arm yourself with knowledge.

  No, Microsoft wouldn't you not solicited. Or they would know if errors exist on your
  computer. So that's the fraud or scams to get your money or worse to steal your identity.

  Avoid scams that use the Microsoft name fraudulently - Microsoft is not unsolicited
  phone calls to help you fix your computer
  http://www.Microsoft.com/protect/fraud/phishing/msName.aspx

  Scams and hoaxes
  http://support.Microsoft.com/contactus/cu_sc_virsec_master?ws=support#tab3

  Microsoft Support Center consumer
  https://consumersecuritysupport.Microsoft.com/default.aspx?altbrand=true&SD=GN&ln=en-us&St=1&wfxredirect=1&gssnb=1

  Microsoft technical support
  http://support.Microsoft.com/contactus/?ws=support#TAB0

  Microsoft - contact technical support
  http://Windows.Microsoft.com/en-us/Windows/help/contact-support

  I hope this helps.