SGE2000P loses the manually configured ipv4 address after reboot

I am setting up a new switch SGE2000P as independent. As part of the Setup, I need to assign a new IPV4 address to the switch default instead a 192.168.1.254. After that I applied the changes everything works fine, but when the reboot of the switch get the ip address back to the default. Any contributions to this issue will be appreciated.

Elkins

Hello Evillalona,

I just looked at the issue you are seen and wanted to check with you on this subject.

When you change the settings in the switch then go to the file management section

the switch and make a copy of the running configuration to the startup configuration? I just wanted to

check and see if that would fix the problem you are experiencing. I've heard other people with

the same problem and that was the difficulty for them.

Thank you

Tags: Cisco Support

Similar Questions

  • The mouse settings not saved after reboot/restart

    I'm changing the speed at which my mouse pointer moves on the screen.  I'm doing a 'demand' the change, and then click on 'ok '.   The point of the mouse moves faster in the game.  Then after reboot/restart the computer, the mouse setting is default slower movement speed.   The changes are not saved after reboot.   What keeps the change of speed of movement of the mouse to be saved?

    Mr. Brian,

    Please, try the following steps.  This should allow you to keep all the settings in the SetPoint software at the same time to solve your problem.

    1. click on the Start ORB, type msconfig in the Search box and hit Enter
    If you are prompted for an administrator password or a confirmation, type your password or click on continue
      
    2. in the System Configuration dialog box, click the Startup tab
    3. Locate the entries called KHALMNPR or similar and uncheck the box next to them (there may only be a)
    4. click OK and restart your computer
    5. after reboot, change the speed of your mouse pointer and restart

    This should solve your problem.  Please let us know.  Thank you.

    Shane
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Toshiba 46TL938G loses the WLan configuration after stopping down

    Hello

    46TL938G unpacked yesterday, updated the firmware on the Internet.

    Wireless set in place with WPS works, but configuration is lost after turning the TV market / back.
    I can't use assisted because of hidden SSID configuration.

    In manual mode, I always get a bad autorhization information and/or encryption not supported. Access point uses WPA2-PSK AES.

    Is it possible to Setup WPS paste?

    Any news?
    I recommend you try different configuration scenarios:

    -try password that are more than 8 to 10 characters.
    -Try different encryptions: WPE / WPA - PSK / WPA2-PSK (AES, TKIP or AES and TKIP)
    -try to connect with prior authentication ON and OFF
    -try to connect to the WLan using option hidden network - enabled or disabled

  • Extreme 802.11 5th generation Windows 10 how enter the manual configuration?

    How to do in manual configuration to make a few changes to my configuration? I'm on a windows (10Upgrade) when I'm in the Airport utility, I get an error - 4, trying to get into the manual?

    I recommend that you remove the airport as bonjour for windows utility...

    Restart the computer and then reinstall again. There are several reports of the failure of utility (off date now) airport after an upgrade to windows.

    After that, it could be purely network problems. Are you now internet through EI?

  • Lose the ability to access Internet after Windows updates published in the last 24 hours

    I lose the internet connection if I install the Windows updates published in the last 24 hours.  I have had access to the internet after restoring to a restore point.   I was able to recreate this problem be reinstall them again.

    Update the example is KB2121546

    Manually install a - alone.
    Reset.
     
    Still have Internet?
     
    Manually install the next one, one.
    Reset.
     
    Still have Internet?
     
    Repeat this until you lose Internet or have installed all updates - what comes first.  If you lose Internet - uninstall that one and install all others (using the same one at a time - at the most method you will have 8-9 for this cycle) then come here and let everyone know what update was kill your Internet connection.
     
    Why?  An update of the example is of no help.  There are 9 updates you could possibly have * if * you were aware through yesterday.  Knowing the SPECIFIC update that is causing your problem would be better for you and those who help you.

    --
    Martin Stanley
    MS - MVP
    --
    How to ask Questions the Smart way
    http://www.CatB.org/~ESR/FAQs/smart-questions.html
  • Limits in the Instance configuration file change after restart (sometimes)

    Hi Experts,

    Here, I have a problem.

    The limits of configuration change to the original boundaries after restarting the server

    Ex: Initial account limit: < DefaultRowsDisplayedInDelivery > 75 < / DefaultRowsDisplayedInDelivery >

    I changed to < DefaultRowsDisplayedInDelivery > 1500 < / DefaultRowsDisplayedInDelivery >

    After reboot, sometimes the configuration evolves at the initial stage

    < DefaultRowsDisplayedInDelivery > 75 < / DefaultRowsDisplayedInDelivery >

    The same download limit as change < DefaultRowsDisplayedInDownload > 2500 < / DefaultRowsDisplayedInDownload > 2500 initial value

    Can someone help me in regardin this?

    Kind regards
    Angelique

    Published by: angelique on 23 January 2013 05:21

    Published by: angelique on 23 January 2013 05:22

    Use Enterprise Manager to update configuration settings DefaultRowsDisplayedInDelivery and DefaultRowsDisplayedInDownload for Table and Pivot views.

    If brand pls help

  • How to lock the moniter keep resoultions settings after reboot?

    How to lock the screen to keep resolutions settings after reboot?

    Hello

    Thanks for posting your query in Microsoft Community and my apologies for the late reply.

    • Have you noticed a Windows Update, the installation of the video drivers?

    See the Windows updates are installed
    http://Windows.Microsoft.com/en-us/Windows7/see-which-Windows-updates-are-installed

    Possible reason for this behavior:
    I suspect that a third-party application to start conflicts and it translates into changing the resolution. Once you got the correct resolution after re-installing the drivers set the computer to clean up state of startup and then check if the resolution changes. In this way, we can use the approach 50 / 50 to find contradictory application the cause.

    How to find the conflicting application:

    See the article below for instructions on how to start your computer in a clean boot state. How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.

    Similar was also mentioned in the thread below; in this case, the webcam software was causing the conflict.
    http://social.answers.Microsoft.com/forums/en-us/w7desktop/thread/7bb77d00-8ac0-4d9e-b7a3-7646b9cc1083

    Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

  • Satellite Pro M70 failed to refresh an IP address after reboot of the router

    My laptop is not able to repair the Wi - Fi connection is if I reset the router. I have to power cycle the phone so he can always reconnect as it gets stuck on getting the network address... Known problems with the hotfix on this matter or anything...?

    Thank you

    Huw D.

    Hello Huw

    As much as I know there is has no problems known with WIFI connection and I n know exactly what happens with your WIFI connection. After the reboot of the router try turning off the WIRELESS card with for a short while, turn it back on and try to connect again.

    The parameters are the same and nothing should be changed.

    Good bye

  • Why FM lose the hyperlink works in TOC after the character formats? Or is there a workaround?

    I work in a FrameMaker book.

    Chapter 1 uses heading1 while in the text for Heading1 there is a letter setting out with a character format "sup".

    In the table of contents (TOC), I find the letter outlining perfectly once again, but the hyperlink is no longer.

    Example:

    Hello, this is my < sup > top negative > title 1 title

    In OCD I also find the same text properly, but of the 'up' to the end of the line, the hypertext link no longer works. In FrameMaker or PDF file, I write.

    I tested it with FrameMaker 12 and 13 in the German version and on FrameMaker 7.2 English version.

    Is there a solution?

    Hmmm. I'm guessing that the solution is to fix in Acrobat after you create the final PDF file with the link tool. Here is the operation of text links in FrameMaker:

    • If a Hypertext marker is a paratrooper without a character tag, the whole paragraph is the hotspot.
    • If a hyperlink marker is inside a character in Pará, the hotspot is the limits of the character tag.

    In your situation, the marker will appear at the beginning of the line and the character tag is also across the page and it didn't is not in any way that I know to change.

    Framemaker TOC with hyperlinks incompatible - roundpeg Blog

  • When I first open the browser the web page does not load. I need to go to tools, Options, advanced, network, settings and change the Manual Configuration of the Proxy to no Proxy, and then click Retry.

    Once I change my browser proxy works very well. The problem is whenever I open the program.

    Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > appearance/themes).

    See also:

  • Configuration of updates after rebooting

    am able to install updates day but PC sez 'need to restart the computer.

    When the reboot is complete, message sez "updates not can be configured."

    "returning from the changes.

    Try to apply the patches one at a time, and solve all the issues one at a time.

    Take a look at the Microsoft KB article below and see if the methods to resolve this problem:

    KB 949358: The update is not installed successfully, you receive a message, and the computer restarts when you try to install an update in Windows Vista

    If you read this tip and it helps you, please click on the "useful Vote"button to "reward" myself with 'points'! '. Thank you

    Please click propose as answer to let others know the solution that worked for you

    Link to: Silverlight Applets mapping 2003 Menu for applications of office 2010 Ribbon

    Link to: research of 2007 addin commands PS: MS WHERE IS THE 2010 VERSION! HintHint!

    Link to: Menu Flash Applets mapping 2003 2007 Ribbon for all office applications

  • Office XP is empty and the Start Menu is gone after reboot

    only my wallpaper appeared. My office whole and menu start and the toolbar below (indicating the time date etc) had disappeared!
    I can't click or right click any painted WHAT on my paper.
    I can access only now programs through the Task Manager.
    I tried a lot of things:
    (1) open explorer.exe in Task Manager.
    (2) restart my computer, press F8 I can restore last good configuration, but the office still empty
    Please do not ask me to do the things above, because I tried them all in vain.
    Help, please! >< i="" am="" desperate.="">

    It is always sensible in this situation to achieve a malware check

    Start the computer in safe mode with network and download and install Malwarebytes (free version for individuals only), updated definitions and run in safe mode. Disable other security software while you do the analyses.

    http://www.Malwarebytes.org/

    Download and run SuperAntiSpyware (Free Edition)

    http://www.SUPERAntiSpyware.com/download.html

    Some malware is installing the entries of proxy server redirecting internet connections. If you encounter this problem step 2 see in the following link:

    http://www.myantispyware.com/2011/02/21/how-to-remove-Internet-Security-Essentials-virus/

    How long is since the problem first happened? When you have eliminated any malware you might try System Restore.

    http://bertk.MVPs.org/index.html

  • How to change the resolution of the screen when the "input not supported" message after reboot

    I need to change the display resolution to 1600 x 1024 after I changed my 1900 x 1200.
    the problem is,
    the "input not supported" message when I reboot the PC and does not allow me to do anything.
    He presents himself before the logon prompt.
    I restarted to fail safe with the command line with the id of the administrator and was able to change the resolution, but
    He returns to the State ("input not supported" and no prompt connection) after I restart the PC

    Mark,
    Thank you for your help,
    I tried in vain,
    I just used another monitor with a higher resolution, restore the previous resolution and swap the monitor again.

    Kind regards

    Claudio.

  • no icons on the desktop or the menu takbar or start after reboot

    I restarted my computer, and just the wallpaper came on the screen, it ' no icons or menu bar tasks or start, I tried to do ctrl, shift, ESC to bring up the Task Manager, but nothing happened when I did, it looks like not loading, I can get the pointer of the mouse to move and right-click with him I could see the circle of the mouse when I hit the three buttons, but nothing comes.  So I was able to get I in SafeMode with networking and everything works properly in safe mode.  I ran a bunch of anti-virus and anti-spy and anti-malware scans with startup scans, found a bunch and deleted all, done a search of f-nimda on it and he has not found on the computer. i did a sfc /scanow on the computer, he found no corrupted files. then I rebooted to see what happens samething happened without icons or tasks and menu bar pointed start. so I rebooted again butthis time I pressed f8 and made a last known good configration, and everything came back and works fine now.  but eveytime I restart the computer and leave it alone itgoe just the desktop wallpaper, wth no icons or menu start.
    any idea on why it happene or what to do to put this back to normal wthout using last good configuration known all the time?

    Your computer is not clean (why ever would scan you for the very old nimda virus?) or the operating system has been damaged. Look at the malware removal methods described at the link below. If you were this thorough, then backup your data and do a restore clean factory/install of Windows. If you were not that thorough, go through the removal steps and see what happens.

    http://www.elephantboycomputers.com/page2.html#Removing_Malware

    MS - MVP - Elephant Boy computers - don't panic!

  • the desktop icons will reappear after reboot

    I have Windows 7 Home Premium 64 bit on Asus g60 laptop that I just bought.  I always hide my icons the desktop, but for some reason some they keep reappearing after I restart.  I do not think that this happens every time, but it happens at least at every restart of the 3rd.  It gets really annoying.  Even the "Show desktop icons" box is checked.  Help, please!

    Well, I tried what l1willia said, but it does not solve the problem.  I ended up uninstalling Power4Gear Hybrid and it seems to have solved the problem.  What piece of garbage that the software was lol

    Thanks for the comments and if it does not solve the problem permanently, I will reply to this message.

Maybe you are looking for