Sharing works do not Internet connection

OK im trying to make my computer vista laptop wireless for my xbox 360 and im struggling to try to leave Internet connection sharing when I go to propities and go to the sharing, I have the box that says allow other network users to connect through this computer's internet connection I click on it and click ok , then it opens with an error message indicating an error occurred while the connection was activated and it does never time I try and select it ive tried something different and looked online and can't find someone with the same problem or answers as to the difficulty that I even tried bridging the connections and it did not work im not sure if its because of my computer is connected to a router im trying to use my computer and wireless ICS were like this, it will only work if it was connected to the local network

Hi rhawley64,

Thanks for posting on the Microsoft answers Forums.

Have you tried to connect your XBOX to your computer via a wired connection?

1. first of all, have turned on your Xbox. Also have your PC on, because this next part is everything with the computer. It will probably work with a wired connection as well (but you could probably just hang to the top your modem or router then), but here it is. First go to start and go to your control panel. Switch to Classic view using the link in the upper left corner of the window. Find the network connections and open it.

2. you should see a "connect to the Local network' (or disconnected, it's to connect to the Xbox) and your internet connection (mine is called"Wireless network connection"). Connect the Ethernet cable to your laptop and the back of the 360. Select the 'connection to the Local network. After it is connected, turn off your internet connection. Once it is disable right-click the internet connection, and then click Properties. Go to the Advanced tab and check "allow other users of the network to connect through this computer's internet connection". Allow that this ends, it may take a little bit. Once this is done, your internet connection should say shared next to the State of the connection.

3. check your internet connection. Once it is fully connected, right-click to 'connect to the Local network' and click on repair. Allow only at the end. On your Xbox, find the system control panel and browse until you find 'connection to Xbox Live Test. Test the connection. If it works, congratulations, you don't need this next part. For some, at this stage, they get a DNS error. There are a number of ways to solve this problem.

4. you must have a connection to a router. To browse the internet once again, you must disable the "connect to the Local network' and then to repair the Internet connection (follow the steps above to activate it again once you have finished). Go to http://192.168.0.1. You will be asked for a connection. On most routers, this is:

User name: admin

Password: (no password)

If this does not work, look for the login information for your model of router. Once connected, you have to find where your server DNS IPs would be listed. On the top bar, click State. Under WAN, you should find DNS IPs. Manually enter them into your Xbox (rather than have it find automatically) and test your connection again. At this stage it should work. Any other error can be search online.

After following the steps above you have established a wireless via your computer with your Xbox?

Please post back and let us know if this information was useful to solve your problem or not, so that we can help you if necessary.

Robyn
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

Tags: Windows

Similar Questions

  • Netflix in Media Center returns a 'there was a problem of data recovery. "Check the works of your internet connection and try again" error instead of loading Netflix data.

    context: a previous thread with an identical title never responded, the problem just disappeared.  Well its been two weeks since then and the problem came back.

    somethings which may or may not apply: internet TV seems to work better in media center.  All updates have been applied to H.P. of Vista SP2. Netflix works fine in ie8 (such as the internet, of course). Tried to delete all the Internet Options, delete browsing history section of Internet Explorer. I get the same error message with my windows 7 professional media center, but netflix seems to play anyway (no game with vista). I recently installed quicktime alternative 2.72 to see what it was and how it worked, then removed and put back in quicktime.

    Tried / symptoms:

    -Remove all the browsing history (econcepts)
    -Same message on Win7pro but works even when (econcepts)
    -Works on Win7 no problem (omegafiler)
    -Works in ie 8 (econcepts)
    -Works in crome (Martin TX)
    -Consensus is that it started around December 30, 2009 (GeoffG1, johnetX, me)
    -Remove and reinstall silverlight (omegafiler)
    -Remove and replace netflix plugin (omegafiler)<- how="" did="" you="" do="" that="">
    -Netflix says: microsoft problem (Nitestalker)
    -Microsoft is silent (this thread - on vacation?)
    -Same problem on 32-bit and 64-bit VMC (JRSMiamiFL)
    -No applied update (johnetx)<- perhaps="" date="" related="" or="" drm="" date="">
    -Disconnect from netflix, you reconnect again - ultimately the same error (chicagokiwi)
    -Tried to reduce the number of items in the queues to well below the limit of 200 (econcepts)
    -Tried the register / unregister the third wire procedure, no joy (does not break anything else however)
    -Disabled the firewall, no change (econcepts)

    related topics:
    http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/0c154c0a-1fcb-4353-8c5e-b394e885256d

    http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/aaab24a0-4BB9-42FA-a5ee-46a733d6560f

    http://social.answers.Microsoft.com/forums/en-us/vistamedia/thread/f05f69c7-6456-4117-B302-27c08886ea1e

    Someone else knows Netflix not being is not able to connect?  It started yesterday (30/12/2009) for me.  I looked fine the day before without problem.  The message I get says "there was a problem of data recovery.  Check the works of your internet connection and try again. Ok.  I make it work with both my VMC - one with the service pack and the other without.  My OS updates have been loaded in early December, so I don't see how this could it be.  I searched and found this problem has come up before, but I have not found a solution.  I made NO changes to my HTPC.

    Those who have and solved this problem.

    UPDATE UPDATE UPDATE UPDATE UPDATE UPDATE *.

    2009-01-05 has attempted to start Netflix this morning and you know, it works on both my VMCs.  That's the good news.  So now the real questions are:

    Only 20 people reported it as a problem and only 6 on the green button.  I believe that it affected all the world with Media Center.  So why not discussed much?

    It already happened, causes a stir and silently slips without known cause or cure.  How can we find out what caused this and how to prevent it from happening again in the future?

    *******************************************************************************************

  • Failed to load movies Netflix in Media Center message appears to indicate there was a problem of data recovery. Check the works of your internet connection and try again.

    Original title: cannot load Netflix movies in Media Center

    Netflix photo click on the message appears indicating a problem of data recovery.  Check the works of your internet connection and try again.

    Hi Barbarasimonetti,

    (1) since when are you facing this problem?

    (2) remember to make changes?

    (3) what is the complete error message you receive?

    Method 1: You can follow the steps described in the article below

    Known issues and limitations of Netflix on Windows Media Center for Windows Vista

    http://support.Microsoft.com/kb/972496

    Method 2: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

    How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

    http://support.Microsoft.com/kb/929833

    Thank you, and in what concerns:

    Ajay K

    Microsoft Answers Support Engineer
    ***************************************************************************

  • No Windows 8 Apps work (Message No. Internet connection)

    Hello

    As the title suggests none of my apps windows 8 will work using an internet connection but my internet is fine on the office.

    This has been the case since I upgraded my machine Windows 7 Ultimate for Windows 8, a few weeks ago.

    I have tried many corrections suggested for what:

    1. I don't have any other anti-virus installed outside of Windows defender

    2. I tried a clean boot and the same question

    3. I had the Windows Phone development kit installed with hyper-v which I thought mat be the issue, but this is not the case.

    4. Internet is through a wired DSL, but I also tried a wireless connection at the same modem and same problem.

    5A ran the Windows 8 App troubleshooting tool

    6 ran internet and network troubleshooting

    I can't be an update as I have quite a few programs that are installed and I need to keep.

    Any help with this would be great because my head is pretty painful to striking it against this brick wall.

    Kind regards

    Lastbuilders

    Finally, I got a work around me, and I'm sure that this will work for most of you, people do too, that: -.

    Install a violin 4 Beta
    (1) there is a new feature toolbar point 'Win 8 Config"called"loopback Exemptions Utility AppContainer. "
    2) click on "All exempt", then click "Save Changes".
    Voila! Problem disappeared!
  • Internet connection not working is not wireless, connected to two networks

    I have a problem connecting to the internet via the wireless connection. With a cable, I can connect to the home network and the internet. However with the radio, I have local access to the home network. In the network and sharing Center, it shows that I am connected to the home network but also to another unidentified network. When I click the Diagnostics button to see why there is no internet connection, he said that the problem is that there is more than one connection and that I should remove one of them. When I disconnect the network or unidentified network, they have both disconnect. I tried to reset the wireless adapter, reset the router and do a system restore and none of these worked. Does anyone have any suggestions?

    Hello
    1 did you change on your computer before this problem?
    2. What is the exact error message?
    Follow the suggestions and then check out.
    Method 1
    You can run the network troubleshooter utility.
    Using the troubleshooter from network in Windows 7
    http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

    Method 2
    You can disable temporary, your security software and then check.
    Disable the anti-virus software
    http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
    Enable or disable Windows Firewall
    http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off
    Caution:
    Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

    Method 3
    Check if the problem persists in a clean boot state.
    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
    http://support.Microsoft.com/kb/929135
    Note: After a troubleshooting follow step 7: reset the computer to start as usual

    Method 4

    You can follow the procedure in the article.

    How to reset the Protocol Internet (TCP/IP)

    http://support.Microsoft.com/kb/299357/en-us

     

    Method 5

    You can follow the procedure in the article.

    How to determine and to recover from Winsock2 corruption in Windows Server 2003, Windows XP and Windows Vista

    http://support.Microsoft.com/kb/811259/en-us

    See also:
    Network connection problems
    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems
    The problems of Internet connection
    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems
    Using event logs Windows Network Diagnostics to solve network problems
    http://Windows.Microsoft.com/en-us/Windows-Vista/using-Windows-Network-Diagnostics-event-logs-to-solve-network-problems
    Windows wireless and wired network connection problems
    http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  • 64-bit Internet connections work, 32-bit Internet connections do not work.

    The system configuration:

    • Windows 7 Home Premium 64-bit
    • HP Pavilion P6310f
    • AMD Athlon 2 x 4 630 image processor
    • 6 GB DDR3 RAM
    • nVidia graphic Chipset

    Symptoms:

    • all 32-bit internet programs do not detect an internet connection and cannot connect to the internet.
    • Internet Explorer (32-bit) displays instantly "Cannot Display the Webpage", there is no apparent delay or the connection attempt.

    Counter-arguments to skeptics

    • Computer starts completely, no error message.
    • Network and sharing Center shows "Access Type: Internet", detects no problem.
    • Windows updates work
    • Internet Explore 64-bit works

    I work for a local computer repair business, and I've seen this problem now on at least 3 machines.  I've almost exhausted all means to try to solve these problems, ranging from to restore the system registry changes.  Nothing seems to have helped.  Here's what I did on this specific problem:

    • Reset Internet Explorer settings
    • Reset the Internet Explorer advanced settings
    • netsh winsock reset

    Until you try and suggest that it is an internet explore addon, I said all THE 32-bit programs, so that some programs use the Internet Explorer settings for the communication of the internet (for example, proxies) they are not affected by the integrated addons.

    I thought I could keep from doing another massive troubleshooting on this one and see if anyone else has a better answer for me.  So far I've never seen someone say they got this fixed solution without saying 'I reformatted my computer and it's corrected now.  This isn't a good solution for a problem caused by potentially a single file.

    So, anyone have any ideas?

    Hello

    ·         What is the security software installed on your computer?

    ·         What were the changes made to the computer before the problem occurred?

    Method 1:

    You can check on what is happening in SafeMode with network option. Follow the link to start the desktop in SafeMode with network.

    http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

    Method 2:

    Also uninstall the security software temporarily and check if it makes a difference in the way applications respond.

    Once you have done to resolve the problem, reinstall the software.

    Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

    Hope this information is useful.

    Amrita M

    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • iPhone 6 and some applications do not work without an internet connection

    If I'm not connected to WiFi, a number of applications will not work.  Error message says "no internet connection found.  Please sign in to continue. "Is there a work around?

    You have a cellular data connection good in time?

  • WNDR3700 not internet connection due to the storm

    My modem to broadband ISP (ARRIS TM822) was killed during a storm, it was replaced with the same model, and at the beginning, when I plugged my router, the wireless worked well. I'm not in the settings or something, just plugged in, and it worked perfectly. However the next morning, I was unable to connect to the internet.

    I did a lot of troubleshooting:

    • Firstly, I fed all the way down, pulling cables, batteries on the modem, etc and started in sequence. This is done several times without success.

    • I updated the firmware on the router, done the commissioning, no luck

    • Connected on the router, using the routerlogin.net and run the configuration wizard. Got the message saying 'No Internet connection detected' ' Please check connection to the modem cable/DSL and of Internet WAN port.

    • Did a factory reset and used the resource CD. To the tab of preparation, got 'No adapter' ' is either disabled or no Ethernet card Ethernet card is installed on this computer...» "I've updated the driver for the LAN on my computer (it's something RealTek) and uninstalled and re-installed. Same result.

    • In addition, the port is very well. The LED indicator for the Ethernet port is shining green on the router and the computer, the port "lights" to show a good connection. It also works very well when it is connected directly to the modem.

    • The State of the computer shows LAN network data is sent and received when it is connected to the router, quite strangely, even if I can't connect to the internet.

    Thus, it has been a long and frustrating day. I'd appreciate help on solving this problem.

    Thanks in advance.

    Hi Elaine,.

    I couldn't make it work. I pretty well confirmed, however, it is the router. I tried another router and it works very well with the modem, and I had a friend check my router on its network. It did not work there either. I'll have to buy another.

    Maybe it was damaged during the storm that killed the modem. Just very strange that he worked for a while before stopping and that he was not completely killed as the modem, just maybe the internet port. Both have been connected to a surge protector as well! Maybe I can get compensation from the manufacturer. Well...

    Thank you for following it upwards.

  • Vista SP2 not allowing not Internet connection

    I recently installed the new windows vista sp2. Now, I did that I was not able to connect to a wireless network and the internet sometimes decides to work when it is connected through the LAN.

    I went back to sp1, and now it is fine.

    does anyone else have this problem? If yes how can I fix?

    Hello

    Thank you for using the Microsoft Windows Vista Forums.

    So that the network is working properly, let's check to see if your network services are working properly.

    1. open the Start Menu

    2 type services in the start search box and press enter

    3. click on continue in the UAC prompt

    4. search for network connections, network list Service, knowledge of network and Service of Network Store Interface locations

    5. check that the status is set to started and Startup Type is set to automatic

    6. If this is not the case then right-click the service and select start to start the service

    7. make a right-click the service and select Properties, change the startup type to automatic

    8. repeat if necessary for the services listed in step 4

    If you still have the problem of connection to the network or to the internet follow this steps that fixes most of the problems of connectivity.

    To reset the stack TCP/IP go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:

    How to reset the Protocol Internet (TCP/IP)

    http://support.Microsoft.com/kb/299357

    Disable the IP helpdesk:

    1 hold the Windows key and type R, type "services.msc" (without the quotes) and press enter

    2. scroll down to the IP assistance service, right-click on it and select Properties

    3. in the drop-down list box that says "Automatic" or "Manual", set it to disabled and then click 'apply '.

    4. then click on "Stop" to stop the service from running in the current session

    5. click on OK to exit the dialog box

    Disable IPv6:

    Try to uninstall IPv6 on all interfaces, the removal of virtual cards of IPv6 and reset the TCP/IP stack. To remove the IPv6, go to the properties for each network adapter, and deselect the check box next to the Protocol "Internet Protocol version 6 (TCP/IPv6), which will turn off, or select it and click on uninstall, which withdraw power off the computer.» Then go into Device Manager and remove any 4to6 adapters, adapters miniport WUN or tunnel adapters.

    NOTE: You should do this for each network connection.

    Disable the DHCP Broadcast Flag:

    Link: http://support.microsoft.com/default.aspx/kb/928233

    Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

    322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows

    Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

    To resolve this issue, disable the DHCP BROADCAST flag in Windows Vista. To do this, follow these steps:

    Click Start, type regedit in the search box, and then click regedit in the list programs.

    If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

    Locate and then click the following registry subkey:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\ {GUID}

    This registry path, click the (GUID) subkey that corresponds to the card network that is connected to the network.

    On the Edit menu, point to new, and then click DWORD (32-bit) value.

    In the new area #1, type DhcpConnEnableBcastFlagToggle and press ENTER.

    Right-click DhcpConnEnableBcastFlagToggle, then click on modify.

    In the value data box, type 1 and then click OK.

    Close the registry editor.

    By setting this registry key to 1, Windows Vista's trying to get an IP address using the BROADCAST flag in DHCP Discover packets. If that fails, he will try to obtain an IP address without using the BROADCAST flag in DHCP Discover packets.

    The only program that I'm aware of that currently relies on IPv6 is the new Windows meeting space. The first 2 changes will cause this program is not to work - but all of your normal (IPv4) connections will leave unaffected. If it causes problems that you can't overcome, simply go back to the original settings.

    To clear the DNS cache:

    Click Start, type cmd in the search box, and then click cmd in the list programs.

    If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

    Once at the command prompt, type ipconfig/flushdns

    You can click on the link to try a few other network basic troubleshooting steps

    Network connection problems:

    http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

    Please post back and let us know if it helped to solve your problem.

    Kind regards

    KarthiK TP

  • CC sees not internet connection

    Hi, I can't open my CC apps as my CC does not see my internet connection, I get the error: "your computer seems to be offline. An Internet connection is required. If please connect to the Internet and try again. "I'm connected to the internet... This is a new problem, as he has worked for months, why it suddenly does not work?

    HidiPixi74, allows to try the solutions mentioned in the article below and check if that helps.

    http://helpx.Adobe.com/x-productkb/policy-pricing/activation-network-issues.html

  • Linksys does not detect not internet connection.

    My linksys router hotspot does not detect my internet connection. My internet connection is clear. How would I fix this? Help, please.

    Hello

    You need to reset the Linksys router and then check if the problem persists.

    Note: you need to contact Linksys in order to reset the router.

    Hope this information helps.

  • My local network works, but why I can't ping? LAN works but not internet. A simple quest to the Jedi.

    Hi all!

    I have weird problem and I hope some of you can enlighten us if necessary.

    The background:

    My OS is Windows Vista Home Premium SP 2.   One day, I installed an application proxy - ProxyCap - as a free trial for 30 days.  The application installed a few dll Winsock provider.  After the 30 day trial, I uninstalled the app.  Then the problems started.  Even if the application proxy has been disabled, regular internet links have been completely normal and not affected.  It was only after uninstalling the app that I have problems.

    The problem:

    • The computer is unable to connect one more to any website using the browser.
    • My local network seems to be fully functional, which involves a problem of setting the software.  I say that my LAN is functional if I am going to sign--> Network and Sharing Center--> view status and look under the "Activity" section, I see the link send and receive packets without problem.
    • If I go into control panel of--> Network and Sharing Center--> view status of--> diagnosis, I get the message: "cannot communicate with DNS Server (xxx.xx.xxx.xxx) Network Diagnostics ping to the remote host, but has not received a response."
    • Indeed, if go to start--> cmd and ping my DNS server, I get a general failure for all 4 packets sent.
    • However, I am able to ping my localhost to 127.0.0.1

    My settings:

    • My ipconfig/all output: http://pastebin.com/Ksn2k2ja
    • DHCP is enabled.
    • For the properties of connection LAN--> Internet Protocol Version 4 (TCP/IPv4)--> properties, I 'IP automatically get an address' and "Obtain DNS server address automatically" selected.
    • The same goes for--> Internet Protocol Version 6 (TCP/IPv6)--> properties.
    • The Sysinternal autoruns--> tab providers Winsock application, tells me that I have the "Hello Namespace Provider' active as a WinSock2 registry entry. It is mdnsNSP.dll and published by Apple Inc..  Who was present before installation of the proxy, and this is for iTunes.  Screenshot: http://i1300.photobucket.com/albums/ag86/applemeetworm/winsock_zpsb41ca872.jpg

    What I tried:

    • I tried to reset Winsock for Vista by clicking Start--> cmd and type netsh winsock reset , and restart the computer.
    • I tried to reset the TCP/IP stack by clicking Start--> cmd and type netsh int ip reset c:\resetlog.txt and restart the computer.
    • Restart my router.
    • Deactivation and activation then my connection to the local network.

    Thank you all for helping me with my problem.  I would be happy to provide more information as needed.  Thanks for the research and thanks offering solutions.

    See you soon!

    Hi all!

    I contacted ProxyCap and support staff has been able to solve the problem.

    Apparently, one of my entries in registry Winsock2 (Winsock2, Namespace Catalog5, 5 catalog entries) has been disabled somehow, uninstalling or in my first attempts to address issues after uninstall.

    Thanks to ProxyCap and for other people who have tried to help.

    ~ Congratulations ~.

  • Photosmart 5520: Not internet connection post update download

    5520 new. Connected to internet and downloaded straightup update. Now I get "server connection error... check the connection etc. This is done via the touchpad printer so the browser interface. Then... no ePrint or possible applications. Direct wireless for devices works fine.

    Could it be a corrupted download of update? Anyway to force a reinstall?

    Any thoughts?

    Let's define an external static IP and DNS address for the printer:

    -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
    -Enter the IP address in a browser to reveal the internal settings of the printer.
    -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
    -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
    -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
    -Enter the IP of your router (on the Page of the Network Config) for the gateway.
    -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
    -Click 'apply '.

    Now, stop the router and printer, start the router, wait, and then start printing.

    After that, you will have to redo 'Add printer' using the new IP address.

  • T61p not internet connection WiFi

    I have a T61p 6459 with an Intell Wireless WiFi Link 4965 AGN inside network adapter. It was working fine until the right signal strength for a few days when I would be connected to the network all of a sudden I would lose Internet access but then I always 100%. I have tried dissconnecting and that has not worked. Then I rebooted and it worked but only for a few hours, what is the same thing. Now, even with a reboot I have 100% signal strength, but no internet access.

    Help me please!

    Your wifi network adapter does not connect to internet, it only connects you to a local access point, usually a router, whose job it is to connect to the internet. Try to turn off your router for a minute or two, in fact completely the unplug, wait a minute and a plug it back in and then see if you can connect.

    If so, you can then focus on an update of the firmware of your router, if the problem persists.

  • File sharing works is not between two computers Windows 7 Home Premium on a work network.

    Desktop computer is connected to a hub that is connected to a wireless router.

    Laptop connects via the wireless router.

    Both computers are in the same workgroup.

    Two computers indicate that they are in the same network of 'work '.

    The two computers 'see' each other.

    Both computers have the same advanced sharing settings:

    • Turn on network discovery
    • Open file and printer sharing
    • Turn on public folder sharing
    • Streaming media is off
    • Use 128-bit encryption
    • Turn on password protected sharing
    • Homegroup connection is not used, but is set to 'use user accounts and passwords'.

    As I try to get the laptop to connect to a share on the desktop computer, the user accounts and passwords on the desktop include the user account and the password for the laptop. This is an administrator account.

    There are actions on the desktop computer and these actions include the credentials of the user of the laptop computer with read/write access.

    Or machines is now faced with my right. I know one of them use AVG Free, but I'm not sure what the other computer uses for antivirus.

    I get the error message has to do with the user account that I use is not eligible not by office machine. I'll post the exact message when I am in front of the computers within a few hours.

    Sharing files between the two had worked, but then stopped. When you first install file sharing, that I had run into a different problem on the desktop where all settings indicated should be shared, but clicking on through a screen I got a message that file and print sharing has been disabled and I want to turn it on? (even while fixing in advance sharing settings says he was turned on...)

    Any ideas? I'm pulling out my hair. Thank you!

    Steve Woodward

    Seem firewall windows are playing games with you, try disabling it to see if it will work.

Maybe you are looking for

  • iPhone used to install ios 9.3.5

    My iphone 5s will download the update, but every time I try to install it it says "cannot install the update. An error occurred installing ios 9.3.5.

  • How to rename a folder of bookmarks?

    I created a folder based on bookmark and now I want to rename it. How can I do?

  • memory for z60m

    Hello. Sorry for the question. I have an Ibm thinkpad z60m with a ram of 512 MB. I know I can improve up to 2 Ghz. What type of memory I need to get? And where can I buy it? I would like a 2 Ghz module. Thank you. Bye,. Davide P.S. I live in Italy.

  • Keyboard N200 problem

    the keys on my keyboard mГЄlГ suddenly becomes 'I' 6 ', 'u' 4' I tried to restart and stop the keyboard, but it did not work, what should I do?

  • HP pavilion dv6000: help with password for my laptop

    Hello I bought this laptop off my cousin so I can do my online college classes and hanging out at the star of money to but it asks for a password and he thought it was the name of the wife of Hus if it is well proven was not, and after u entered 3 ti