Should I reset the FPGA FFT when changing the input signal?

Similar Questions

• -Data 200141 was replaced before it can be read by the system. Mechanism of data transfer is interrupted, try to use DMA or USB in bulk. Otherwise, divide the input signal before taking the action.

  Hello

  Installation program:

  2 x PCI-6602

  Configuration:

  Sampling the five PWM signals of 50 kHz using five counters (2 on a map) and three on another for about 10-15 seconds by recording continuously.

  All meter tasks are configured for DMA transfer.

  Problem:

  I get 200141 errors from time to time.

  Question:

  I tried to increase the size of buffer and all tasks of meter are set to DMA. In the error message the last suggestion is to "divide the input signal before taking the action. I don't understand this suggestion. What is meant by "split the signal before taking the action?

  I am open to other solutions to the problem.

  /Mola

  Yes, I know that the 2 MB/s sound do not like much, but it's a way of high load very low tolerance to try to get 2 MB/s.  You have 5 DMA controllers to negotiate access to the bus and each transmits only 1 or 2 samples of 32-bit whenever he gets access.

  I've seen published baseline data where the maximum sustained rate was< 1="" million/sec="" (don't="" recall="" if="" it="" was="" mbytes="" or="" msamples). ="" as="" i="" recall,="" finite="" acquisition="" mode="" allowed="" higher="" rates="" for="" shorter="">

  Ah yes, here is a link that leads to the other links.  See the section on "The counter of the FIFO" in the first message.  Do you see a * very * significant difference in the performance of the M series for the series X-series.  Here are data for counters of the E series.  (It is fair to note that the comparative analysis was conducted with a much older PC hardware).  For the 6602 counter chip was designed between E- and M-series series, so you can probably expect performance in-between.

  Also note that the benchmarks seem to have been done with a task of window unique tent of owning all the bandwidth PCI as possible.  Since you would have 5 tasks they negotiate access, you lose definitely even more overhead.  In addition, for fair comparisons, your 50 kHz PWM would act as a measure of 100 kHz since you have 2 semiperiods to DAB per cycle of 50 kHz.

  Now that I've seen benchmarks once again, I am convinced that it is a no-go for you with just the 6602.  The good news is that the series X-series seem able to yet more ridiculously than I remembered.

  -Kevin P

• In Labview 8.5, what happens if the input signal exceeds the scope of the signal defined by the DAQ Assistant?

  Hi all

  This should be a pretty simple question, but I can't seem to find the answer online and currently do not have the functionality to test this:

  I'm using LabVIEW 8.5 and have a VI that imports data from sensor through the DAQ Assistant. In the configuration tab, there is a range of signal input. What happens if my sensor exceeds this range? I get a warning? The default value is the maximum (or minimum)? I was interested in writing a code to display an error that I approach the limits of this range, but did not know if I also need to include code to display an error if the scope is exceeded as well.

  Thanks for the help,

  Tristan

  Hello, Tristan,.

  The behavior depends on the selected range and the device you are using.

  If you are using a device with a single input range is valid, we will use this range, even if you set a smaller minimum and maximum in the DAQ Assistant.  So, if your device only supports ±10V and you set the range to ±8V, you will still continue to get valid data after your top sensor 8V until what you approach 10V.  When you reach the limit of the extent of your device, the output will be 'rail', and simply return the maximum value until the signal is less than the maximum value again.

  Note: A device that is nominally ±10V usually has a go-around (such as ±10.2V) which are usually specced in the manual.

  However, if you use a device with several ranges of entry then things become more complex.

  NOR-DAQmx player will choose the smallest range that entirely covers the interval you choose.  For example, suppose that your device supports the following input range: ±0.2V, ±1, ±5V, ±10V and you choose 0V - 3V as the range in the DAQ assistant.  The NOR-DAQmx driver will focus on the input range and the list of the entry lines that your hardware supports and choose the smallest encompassing the entire range that you set.  This would be the ±5V, because this is the only beach that contains up to 3V.  Thus, all between ±5V input signal is returned and none outside this range will be 'rail' to the maximum or minimum value.

  We do this because using small beaches make more efficient use of the resolution of the ADC.  So, we try to use the most effective range based on what you ask without picking up a range that will make you miss data.

  Let me know if I can clarify it more.

• Desgning a VI that time / interrupts a film according to the input signal

  Basically, what I'm trying to do is to design a VI who plays or pauses a movie according to the signal it receives. This VI will be used with an EEG device, and what I want to do is play the movie if the signal exceeds a certain threshold, and it stops if this isn't, in other words a VI that responds to neurofeedback.

  As I don't have access to the equipment of the GET yet, I use a sine wave at the moment than the EEG signal in VI of the attachment in this post (which of course will be later replaced by waves of EEG recording), and what I want to do is to read the film if the signal is greater than 0 and put the film on hold if the signal is less than 0. Any help would be appreciated

  Kind regards

  varkong

  I have included the code for the LV8.6 version.

  Concerning

  Prashant

• How the input signal updated step in simulation?

  Hello

  I have my own model of transfer function. I did first with Matlab/Simulink simulation and succeeded. I use the Signal Generator in Simulink to get out my custom step signal. I modified my step so signal to:
  t = 0 y = 0
  t = 0.1 y = 0
  t = 0.1 y = 50
  t = 10, y = 50
  t = 10 y = 65
  t = 30 y = 65.

  It's the kind of staircase input signals. Now, how to build such this approach custom signals to be fed in my transfer function. I tried the function 'Not of Signal' of the 'Simulation', but I can only get the 50 and I don't know how to add more "staircase" in my input signals. Could someone help me?

  
  

• The computer is very unstable... Should I reset the computer to the original state with Dell recovery

  As there is no support for Windows XP SP2 updates (I managed to get the Microsoft SP3) if I go back to my computer to the original state with recovery Dell how do I get Service Pack 2 and 3 again.  Deleted files gives access to the trash... they no longer heard by KIJIJI when I tried to place an ad that some well known hacker has been using my IP address.  This means that he can see literally everything I do on my computer.  Really need help

  overthehillandonaroll

  Run Windows Update after recovering the system.  It will offer you all the updates, including service packs.  Run repeatedly until it shows that no more updates to date are available. Boulder computer Maven
  Most Microsoft Valuable Professional

• LabVIEW basics - Cahnging Boolean State question based on the input signal

  Hi all

  I would like the State to change the Boolean indicator based on a simulated sine wave signal. I have partially managed to do this but need help to develop it.

  See the attached vi. At the present time changes Boolean false to true when the value of the signal is greater than 8 or lower than-8.

  The focus I need is:

  Once the signal passes more than 8 (and the Boolean value becomes true), I hope it becomes false again to a value of 9, but only after the peak value was passed or when the signal is down.

  Similarly on the negative side of the graph, I want the Boolean value to become reality at 8-under, stay true until after the peak value was passed and then back to false when the value is greater than-9.

  Any suggeastions?

  Thank you

  While Crossrulz responded, I had a little look.

  Don't let me spoil your pleasure with the VI attached. Have a go yourself.

• My video is black, as is the input signal, the camera works like the other party can see my photo

  Skype video calling on my video and entering video as black rectangles

  Checked with a one off Youcam program and get a black square too, but the camera works like video caller can see my fine picture.

  Guess that's a direct x issue, made an update of windows, no wizz kids help out me

  Area right but bad parameter, I finsihed changes the tab video, video two and changed its basic color to substitute application settings has been swicthed on and I have swicthed he took. Now works OK

• SMU-4304 causing the ripple on the input signal?

  I have an SMU-1082 chassis that contains a high-6341 and a PXI-4304 module.  To check my code, I have connected the analog input (channel 0) of the 4304 to the digital output (PFI 12) of the 6341.  My program VI shows a ripple of Vpp 0.2 on the analog input that I'm not using a scope.

  The wiring is SMU-6341 [12 PFI, DGND]-> SCB - 68 a,--> TB-4304 [AI0 +, -]-> SMU-4304

  I have attached photos of the verses reach the graphical VI.  The scope is the AI0 + AI0-terminals and the TB-4304.

  Y at - it a supplement on the ground that I should use, or is - this normal for the-4304 to add the ripple?

  Thank you

  Ron

  Short answer, is that there is nothing wrong with what you see.

  You have connected a digital output signal low impedance to a digitizer analog high input impedance. Since a digital signal is essentially a square of variable in time wave and square wave have edges of transition that contain information of very high frequency, you will almost always see a form of "ripple" (see animation synthesis of fourier of a signal square from this Wikipedia page ). Thus, a digital output signal is more concerned with the synchronization and the upgrade to be a square wave perfect.

  In addition, you can see additional "ripple" because of differences between the SMU-4304 and the noculars that you have demonstrated. the noculars can be a combination of a bandwidth of upper entrance (which can come from various sources like low sampling frequency on the 4304 which would result in a higher frequency of information recorded by the noculars for smoother transitions to research) and, possibly, a lower input impedance (causing less, if any, the reflection of signal which would cause the ringing of the signal).

• 4 counter of entry &amp; 6 the input signal HELP

  Hello friends,

  I have a small problem, would be great if someone can help me.

  I use the counter inputs on my CQI data. Harware to measure the pulse of my sigal entry width.

  Since the material has only 4 entries of meter I can connect 4 channels, but I want to measure the pulse for 6-channel width.

  Is it possible to use the 4 available counters and measure 6-channel?

  Thank you

  Kind regards

  REDA

  In my example (very basic), you can just increase the timeout for ~ 10 + seconds to ensure you acquire the pulse.  It is possible that the pulse is not present in the ~ 10 + second timeout, you must also handle the timeout error, so it is not wrap around back through the shift register and prevent future readings to run.

  Of course, the downside of this is that it could take up to ~ 60 seconds in order to gain all 6 channels in the worst cases.  The example was really just intended to show how we can use a single meter to acquire multiple channels in the estate.

  The best way to do it with meters would be to run tasks in parallel (up to) 4 meter.  The first 2 tasks to finish with their initial acquisition should then measure a second channel.  This could still take about 20 seconds if no signals are connected however.

  If you want to trade a lower resolution of measurement (and memory use more) for a lower upper limit on the time of measurement you can acquire a second time 10 window using the call digital inputs instead and use software to determine the duration of the pulse by analyzing the acquired table.

  Best regards

• I lost my connection to the internet, the problem has nothing to do with the input signal. Do everything that contributes to signal the connection disappeared. How can I restore that?

  I remove programs to free up space. now I don't have a connection!

  Hi Steven,

  You get the error message?

  Method 1: Disable the security/firewall program software you run on the computer temporarily and then check if the problem persists.

  How can I turn on or turn off the firewall in Windows XP Service Pack 2 or later versions?

  http://support.Microsoft.com/kb/283673

  If you use a third-party security software, you can check the documentation provided on the software to turn it off.

  Important: Activate Windows Firewall\security software once everything is done.

  Method 2: Follow the steps mentioned in the link below

  How to troubleshoot missing network connections icons in Windows Server 2003 and Windows XP

  http://support.Microsoft.com/kb/825826

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.
  How to back up and restore the registry in Windows

• Router WRT54G3G-ST - no internet connection - cannot reset the router

  Hello.  Some longer story certainly not short (I apologize for the length of hiking...  I don't know what is and isn't important, will scan, please...  I'm sorry...) : recently my computer (Dell XPS 400, Windows XP Service Pack 3, Internet Explorer 7 with phishing filter and pop-up blocker on, SiteAdvisor, up-to-date McAfee Anti-virus and Firewall and a router Wireless-G Linksys WRT54G3G-ST with its AC adapter plugged into the wall power outlet and a network cable directly connected to my computer.) received a drive-by generic.DX!12536d125737 Trojan horse without me download whatever it is one of the few sites I visit every day.  My internet connection has crawled, and I have now no connection at all.

  I've been making McAfee good volunteers forums help quick and very helpful...  They recommended Malwarebytes Anti-Malware for me, I downloaded my own second computer (a laptop) on my flash drive, then on my infected computer.  I ran, tried adapting so recommended, and only then discovered the Trojan horse killed my broadband entirely.  I scanned with it anyway and he quickly found and deleted / quarantine 11 Adware.MyWebSearch related files, but nothing else.  Then, they gave me a link to a patch off updater file and tells me scan in SafeMode until nothing else has been found and check if it has fixed my lack of broadband access.  I did, Malwarebytes found nothing else, but unfortunately I still had no broadband.

  Then, they recommended WinsockXPFix.  Which I ran and he did all his OK registry changes, I restarted if necessary but still no broadband unfortunately.  WinsockXPFix using make things worse for me with the registry changes, did he?  I used the backup of the registry to save the registry before changed files before running.  Should I come back since I don't always have a broadband connection?  McAfee volunteers kindly then told me that I had to hard reset the router, but I tried many times with no fortune.  I'm at a loss as to what, if anything, do we hope to get my broadband, please...

  It is very confusing with many different variants for resetting routers, and what should I do to my router model (Variations: unplug this cable/adapter exactly where; pressed the reset button between 5 and 30 seconds, the computer restarts, or no, 1 or 2 minutes between different steps, waiting or not - and for all these exactly when in the restart procedure.).

  I have reset once before with the reset button, page of routers to http://192.168.1.1default admin password, then it changed to security, etc. but this time I can't make it work.  I'm happy as possible to try once again to get an appointment by perhaps, something please...  When I go to http://192.168.1.1 now, or to any other address, Internet Explorer gripes at me that I am offline, which is annoyingly correct.  I do not have and never had Zone Alarm, but disable my McAfee Firewall does not help.  IPCONFIG at the command prompt gives me an address of 169.254.X.X assigned Windows

  I was going to use the routers Wizard installation CD to try to reset the router, and if that didn't try to get its firmware version number to perhaps upgrade.  But I was going to ask here first of all for expert advice because I read a lot of things that can go wrong during the upgrade of the firmware.  However, analysis the CD (without launching the CD). McAfee found the virus W32/HLLP. Philis.ini in the file "D:\_desktop.ini" on the CD.  McAfee didn't delete the file, I don't know why.
  I scanned my computer together several times and no infections have been reported.  I downloaded the file several times, both www.virustotal.com (39 online antivirus) and virusscan.jotti.org (20 online virus scanners) and every time each virus scanner didn't report any possible infection.  My updated virus scanner McAfee reported a false positive and still Jotti and VirusTotal 2 scanners from McAfee report the file as own probable?  Is "_desktop.ini" a file legitimate Linksys?  I have not found any information on Linksys forums about this.  My problems just keep multiplying... mentioning problems more...

  Find this suspicious file on the CD I decided to download instead the Linksys Setup Wizard
  (Router product page: http://www.linksysbycisco.com/US/en/support/WRT54G3G-ST/download )
  File: http://downloads.linksysbycisco.com/downloads/WRT54G3G-ST_SetupWizard_4_2_06042008.zip)
  my flash drive, then on my infected computer that is connected to the router.  I ran it (downloaded the version of the file: 4.2.0.007 - original version CD Setup Wizard: 4.0 print on CD front) and immediately gave it 1 of the 3 options: Mobile broad band only, high flow only WAN, or WAN high throughput and high speed Mobile.  I don't know what damage, if any, I caused by continuing.
  It seemed that he was trying to go in the entire router configuration process.  I thought it would take me to some options to reset the router, as I read in the user's Guide, and besides - it is my understanding.  The installation process stopped at only 30% done "router not found, make sure that the router is connected correctly and try again."  How many Overwrite original router configuration files I did continue?  I'm quite confused.  The wizard does not check if the router has previously been set up before setting up again?  Unlike version caused my router to not be detected by the Setup Wizard?  Is the horse of Troy generic.DX!12536d125737 who killed my trash to wide band my computer settings so badly that my router is undetectable/essentially not configured?

  Update of sorts: I tried one last time to reset the router, and I unplugged/plugged the network cable.  The fact that I had still no broadband on my Dell XPS main use computer that is connected to the Linksys router.  However, my laptop, with map data in the router, was for the first time able to find network - constant connection and speed is great, it's what she allways has been on the laptop (the Trojan/router problems, my laptop only for broadband with the data in the laptop card.).  Perhaps the cable network was simply not re-connected properly/entirely for 1 of the many attempts of resetting, indeed, it could also explain the downloading, installation wizard is not able to find the router/only get 30% done.

  Laptop prompt IPCONFIG/all with data card Sprint inserted into the slot of your laptop:
  IP = 174.158.XX.XXX (Sprint)
  Subnet mask = 255.255.255.255
  68.28.90.91 = DNS servers
  68.28.82.91

  Laptop prompt IPCONFIG/all with Sprint data card inserted in the router:
  192.168.1.1XX = IP address
  Subnet mask = 255.255.255.0
  Default gateway = 192.168.1.1
  = 192.168.1.1 DHCP server
  Servers DNS = 192.168.1.1

  Since my laptop started to work with the data card into the router, I have not tried again to reset the router and I tried the downloaded installation wizard.  I don't want to spoil anything about it any further as I have (?) / the Trojan has, and I need expert advice, please, about which of the 2 if not more, I do (first?).  On my laptop, typing http://192.168.1.1 in Internet Explorer Gets the ToolTip for the user name and password, but I did not.  I read that you should not reset the router or (?) Is it just 1 or two please?) upgrade the firmware unless the computer is connected directly to the router - that is not my laptop.  On my other computer that still has no broadband, Internet Explorer still says I am offline when you type http://192.168.1.1 in.  My IP address on it is still a 169.254.X.X assigned Windows and a command PING 192.168.1.1 prompt returns with 'Destination host unreachable.', as it has been always and even with all the other addresses (with the exception of 169.254.X.X).

  Boring 2nd "update" of all kinds, my apologies for the length, as always: I've been so focused on the horse of Trojan/broadband killing that cluelessly largely forgot I switched with AOL.  Try AOL dial-up does not work, madness thickens...  Software AOL tells me to check my connection, but all the phone cords are connected as should be.  I plugged a phone directly into the wall jack and I get the tone, I can call OK and the phone rings and receives calls OK.  State of the devices-Modems-Properties-Device Manager says that the modem is not working properly, and "resources" tab shows no conflicts.  Query Modem on the diagnosis tab seems OK to me, as does the journal, but I'm certainly not an expert like allways.  I change all the settings from anywhere.
  I noticed and that check IPCONFIG it says that my IP address is 192.168.1.100 it lasts maybe that someday (then goes back to 169.254.X.X), maybe more, I don't know - I don't check that often to define (should I?).  Meanwhile my broadband, or my works switched.  I can PING 192.168.1.100, but nothing else.  I am convinced the wrong killed Trojan horse my broadband and dial-up - I've never had a problem with my prior V.9x DFVc Modem 56 K Conexant D850.  In addition, I am not convinced the Trojan horse is not still lurk everywhere on my computer, I think that it's...

  Any help with the restoration of my high speed/dial-up is greatly appreciated, please...  Thank you!

  Hello.  There has been entirely too long since I answered, I'm sorry.  There is no excuse, and it is terribly rude to me...  You took the time to read and answer me, and I appreciate very much that in effect.  I apologize for being late, I'm sorry...

  After that I left my message, I downloaded several virus/spyware scanners, etc from my laptop on my USB key, then my other computer for some in-depth analysis necessary.  Was one I downloaded Network Magic that somehow, some way fixed both my high speed/dial-up internet on my main computer is connected to the router WRT54G3G-ST.  I don't know what/how he fixed my connection, but the connection high speed flow works brilliantly since...  Network Magic has worked for me, and I highly recommend it to all those who have stubborn lack of internet problems (caused by Trojans to this) that I did.  There is no guarantee this will work, but it did for me in my amazement.

  Network Magic, as is the Linksys is owned by the parent company Cisco.  Respectfully to all the knowledgeable experts here (which clearly I'm not), I don't want to venture out of the limits.  I'm trying to simply hope to be useful and save a few headaches for both you volunteers and users... buy a new router or the computer was in my mind, with all due respect, I recommend suggesting to try Network Magic users if the reset of the router/all other fails, please.  I used WinsockXPFix/WinsockFix utility before using Network Magic, I don't know if it matters.

  I also upgraded my package of McAfee, I installed on my old software rather than uninstall the first, which caused errors in all things virus scanner a critical need.  I install right now, but it caused some delay to refocus my time.  Some virus scans found many Trojan horses, some were same / in the same folders that killed my broadband - which stopped me in my tracks to ensure a clean uninfected.

  Certainly, it doesn't fully explain the long time, and I'm sorry, once again.  It's just that I'm being cautious and slow in all this.  To answer the first very good idea, you did: Unfortunately, there is no room on my other computer to connect the router in to, which even so caused frustration (at the time).  I forgot to include this in my post new length of countless things to see / do not forget...  It was a brilliant idea, however, I thank you...

  Thank you for your time and your help, I appreciate it sincerely...  Thank you...  I think and hope that this matter is resolved.  It seems to be, the router works perfectly as it always has, and I am positively happy as can be in this regard.  Thank you...  Peace...

• USB-6211: analog input signal affecting another of the same map AI

  Hello

  I use the DAQ-nor-6211 map and DAQmx features to read a hammer and a signal of the accelerometer and then use other LabView functions to make the FFT of these analog input signals. However, it seems that the analog inputs where the hammer and the accelerometer are connected generate a kind of noise or influence in other entries of this data that is not connected to any other sensor acquisition board.

  I've had different experiences in order to check if the problem is with reading the card: put the accelerometer and hit the dog in another table where the DAQ card table was located (to avoid the vibrations on the map and a possible noise), ai1 entry was logged on the differential mode on the dog and the ai4 of entry is connected to the output (z axis) of the accelerometer. The other 2 ai2 and ai3, entries that can also be read by my LabView program, are open (i. e., any other sensor is connected to the card). When the structure where the accelerometer is located is struck by the hammer, the signal of ai2 ("x axis" seen in the first attached document) has a curve (on the time domain) which initialize almost at the same time that the hammer and the a3 of entry has a weak signal, but with the swing as well as the signal of ai4. The document "hammer ai1 + z_axis connected_ _x_axis disconnected ai2 + y_axis ai3 ai4" images that I captured the chart created in LabView. On these graphs, it is possible to check on the FFT the ai3 signal and ai4 has the same behavior (with different intensities), and enlarged figure of time domain image, we can see that the signal of ai2 increase almost at the same time of the signal of the hammer (ai1). The signal picked up by the sensors are probably creating a sort of noise on open entries ai2 and ai3.

  Another experiment was conducted to check if the signal from a single entry that may affect the signal read from each other near the entrances: the DAQmx task Create channel had a physical channel has changed: ai3 entry has been modified by ai7 (maintain the same connection mode: differential), and the results are visible on the second attached document. In the graphs obtained in this experiment, it seems that the entrance of the hammer (ai1) affects the signal of input ai2 and ai7, which are not connected. And the ai4 signal does not seem to influence the other inputs, because he has a different curve on the graph of the FFT.

  The same experiment was conducted using the CSR connection (change threads and create the DAQmx Channel Configuration), but the results were the same as those found using differential connection.

  Finally, if the output of the accelerometer is connected on the ai2, the signal of the other open entries ai4 and ai7 seem to be affected by the signal of the accelerometer on ai2 (last document attached).

  Could you tell me if the problem I encounter is caused by the DAQ card with this information that I gave to you? And if the answer is Yes, do you know if there is a way to avoid this noise create in one entry on the other hand, it please?

  Thank you

  Maybe Ghosting or crosstalk? Just an idea.

• How NI PCI 4474 DSA detects an overload to the input channel?

  I read "Manual user OR dynamic signal acquisition." It is written that NI PCI 4474 support only digital overload detection.

  Here's my question. What is the detection of digital overload? If an analog signal is already converted to digital signal, it can not be signals exceeds the limit. Or the DSA may already be damaged during the CDA process, if there is surcharge from the input signal. Thank you.

  Hyun

  Yes, the chip has more information about the Board and apply factors of calibration, which is how it can overflow.

  What we call "detection of overload analog domain" requires more equipment (i.e. a comparator circuit) to observe the input signal.  Given that the Committee in question is not a comparator to check the input signal, and the way we want to give the user an idea of whether or not their signal is too large, we simply use the mathematics inside the chip. It's better than nothing.

  Oh, and I should mention that the protection is managed by a completely different circuit.  The specification should say how much voltage you can apply to the Commission before the protection comes into play.

  Germano-

• create 4 pulse digital output at the base of the ttl input signal

  Hello

  I am a beginner in Labview and would welcome advice on how to solve the following problem.

  I'm setting up a train of pulses TTL and would like to send in Labview as input.  Each falling edge detected on the input signal, I would like to as Labview to generate 4 pulse digital output.  For each output pulse, I would like to be able to specify the period and duration.       The image should illustrate more clearly, with the figures showing the expected scale.

  

  System: NI PCI-6733 data acquisition card, Labview 8.5

  My daq card has 2 timers 24-bit and 8 e / s digital, but I don't know what the best approach is to create between the pulse output of 4 to 8 of this precision... should it be handled at the hardware or software level?  And how would I go about it

  Thank you

  -Sidney

  Hi noli.

  I found the problem, in fact PCI-6733 support only avoiding the digital output. The timing of software is limited to 1 kHz in case better.

  I'm sorry, but this function is not possible with a PCI-6733.

  Concerning