show 2 connection to y550p

Similar Questions

• My itunes has been updated the software on my iphone 6 and then it crashed and now my iphone is showing the connect to itunes symbol - but now, it is not recognized by itunes?

  My itunes has been updated the software on my iphone 6 and then it crashed and now my iphone is showing the connect to itunes symbol - but now, it is not recognized by itunes?

  These can help:

  http://support.Apple.com/kb/HT1808

  For a Windows PC, try this http://support.apple.com/kb/TS1538

  For a Mac, try this http://support.apple.com/kb/TS1591

• Satellite M30 does not show the connection of the battery after 5 min of use

  Hello

  My Satellite M30 recognize the battery when placed first in and for 5-10 minutes.
  After that the power meter shows I'm on sector without battery. Any advice?

  Anyone know if it is an issue that could be fixed with a new battery, or if it might have something to do with the connection between the battery and the laptop?

  Thank you very much
  g

  Hello

  If the AC adapter is plugged into the laptop that Toshiba Power saver should show a connected adapter. In this case the laptop must not run on battery!
  If you you unplug the adapter icon which appears in the taskbar should move from adapter to battery.

  One question; How old is your battery?
  Usually after several times the battery loses performance and it possible s you will be able to use the battery only for a few minutes. After this period, the battery is empty and needs to be recharged.

  Maybe your battery performance isn't the best right now and it should be replaced. ?:|
  This should be checked permanently.

  Good bye

• Photos shows no connected camera or iPhone. What can I do to import my photos? Thank you!

  Photos shows not connected device.

  What can I do?

  Thank you

  Image capture shows the connected camera?

• My internet connection status shows no connection

  original title: my internet connection?

  My internet connection still works, but the connection status icon shows no connection with an x on it. Who might be a potential problem in the future, or is there a way I can fix it?

  Hello

  Here's a quick troubleshooting network to see there are problems:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows?SignedIn=1

  hope this helps,

  B Eddie

• Media Player - try to burn a CD and the drive doesn't show as connected

  I bought a new DVD/CD-RW unit, it plays the CD but when I go to Media player and try to burn a CD, the burner does not show as connected? It's weird.

  Try this
  http://myvideoproblems.com/tutorials/EnableCdRecording.htm

• INTERNET EXPLORER IS SHOWING MY CONNECTION SUCH AS DIAL-UP OR VPN, I CONNECT DSL

  INTERNET EXPLORER IS SHOWING MY CONNECTION SUCH AS DIAL-UP OR VPN, I CONNECT DSL

  Hello

  ·        Are you able to connect to the internet?

  I suggest you follow the steps mentioned below to configure a connection.

  a. open Internet Explorer and then click Tools.

  b. click Internet Options, and then click the connection tab.

  c. click on Setup and follow the instructions on the screen.

  Apart from that, I suggest you to return the items mentioned below.

  How to troubleshoot possible causes of Internet connection problems in Windows XP

  http://support.Microsoft.com/kb/314095

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Network and sharing Center shows not connected, but the computer is connected to the wireless network

  When I open the network and sharing Center, or hold my mouse pointer on the icon of internet connection in the bottom right of the taskbar, it shows that I'm not connected to a network. However, I know that I'm connected to the internet. My internet and e-mail work correctly. Also, when I click on the 'Connect to a network' option, find the list of available wireless networks, and it shows that I'm connected to my home network. How can I make Windows everywhere where I am connected to the internet, instead of recognizing only on the list of the networks without wire-available?

  Had exactly the same problem on Windows 7 (win7). Connected to the Internet but the status showing no connection and a red cross on the network icon. Problem has also caused problems to connect to Lync and Office365 along with VPN, which apparently uses the status to check whether the connection is available.

  Found the solution here: http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/df17c593-e78f-4878-97b0-7569307934c5

  Apparently, certain permissions gets hurt in the database record and must be fixed using RegEdit. The solution is a step by step and likely to be resolved simply by removing a cache of file using RegEdit and potentially affecting certain permissions.

  It will be useful.

• The network icon shows not connected, but in reality I'm connected and can browse internet.

  Network icon does not display connected

  The network icon shows not connected, but in reality I'm connected and can browse internet.

  Could grateful if someone let me know what could be the reason.

  Thanks in advance

  Hello world

  I had the same problem and I solved it by unplugging my pc to the modem, wait about 30 seconds and reconnected. This means that if you do the same thing with your network adapter problem could be solved. Try this option, you will not lose anything

• Integrated microphone does not and shows to connect Windows Vista

  My microphone does not work, even not show as connected in (microphone) Windows vista

  Hi my microphone has problems. It works sometimes, but usually it does not. I don't know why it is, but maybe someone here can help you. It is really connected and activated, but it does not usually record as being connected. Does it only occasionally. I don't know if something is different when the microphone is, can't remember. I downloaded the latest drivers and have updated their but that did not help. I still have the same problem. Also, it seems that all audio services are running. So if anyone knows the solution I would be grateful.

  If you microphone/Line In set is activated and levels turned up, this is how its window should look like. Note the bar showing the Green microphone resumes his.

  

• Computer shows as connected... but we can not access the internet.

  Original title: but alas... internet no.

  Recently, we had this problem where our shows as connected pc... but we can not access the internet.  What I've been able to solve, is that somehow my IP settings change.

  I'm going to "Obtain an IP address automatically" and "Obtain DNS server address automatically", but of course... when the problem occurs again I find that my "Obtain DNS server automatically an address" has been changed to "use the following DNS server address".

  What is causing my computer to change my settings?

  I think you're DIY too.  Normally, your computer and your wireless router assign dynamic IP addresses, and they change periodically - that is part of the security design.

  In your case, the DNS server is the router.

  Most of the time what you describe is your computer is able to find a wireless router but the router doesn't send an IP (its normal function).

  This is usually:

  1. Your Internet service provider is down or your connection to it is broken.  If this is the case there is nothing you can do about it.
  2. Your computer network security key does not match the one in the router.

  1 reset the modem & router.  Follow these instructions precisely: http://canadiantech.info/?page_id=136

  2. If that does not resolve the problem, you must remove this network from your list of networks to manage Windows 7.  Then try to connect again using the network key, you know.

  3. If this does not work, you will need to do a factory reset on the router and re - install the router according to the router set up instructions.

  4. If after all the above does not correct the problem, you must replace your router.

• Windows 7 network icon systems do not show popup connections

  Normally, when you simply right click on the Windows 7 network icon in the system tray, it opens a window showing your connections and available all other connections. Now however, after using the laptop for several hours, and after that unlocks a few Office and a resumption of the mode standby, this no longer works. I click and nothing happens. The only way I can access this is right-click on the icon, open the network and sharing Center then click on "connect or disconnect." It is a pain I need to connect/disconnect continuously different VPN.

  If I re-boot it starts working again. I can't find the exact scenario to make, work stoppage, but it happens regularly.

  Hope there is a fix for this.

  James

  Hello

  Try these but I recommend that you ask in the TechNet forums also as perhaps more
  He has seen this happen. Usually, this is the icon itself disappearing, not functionality
  you encounter.

  Try the methods below and if no success asking on TechNet.

  Windows 7 IT Pro Forums
  http://social.technet.Microsoft.com/forums/en/category/w7itpro

  -----------------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ====================================================

  After that the foregoing: (here, the NETWORK card and Wifi are interchangeable in the sense that the two must be
  fact that you can do if you first use).

  Follow these steps:

  Control Panel - network - write down of the brand and the model of the Wifi - double click - top
  tab of the driver - write version - click on update driver (can't do anything like MS
  is far behind the pilots of certification). Then right click on the Wifi/NIC device and UNINSTALL
  -Reboot - it will refresh the driver stack.

  If necessary to download drivers on another machine and transfer on the problem computer via
  removable media such as a USB key or CD - DVD.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods
  below is preferred so that the latest drivers from the manufacturer of system and device manufacturers are
  found)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version.
  (Those become your fonts of rescue system manufacturer).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as windows
  7 love the updated drivers.

  ======================================

  If necessary:

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  =======================================

  Other possibilities include something running is interfering - programs suspects antivirus/security
  Among others.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929135

  How to change, add or remove startup programs in Windows 7
  http://www.SevenForums.com/tutorials/1401-startup-programs-change.html

  Autoruns - free - see what programs are configured so that it starts automatically when your system
  boots and you login. Autoruns shows you the full list of registry and file locations where
  applications can configure Auto-start settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• When I try to connect to wifi, it shows this connection is not available.

  OT: problem with wifi.

  I use a fujitsu laptop computer lh532 and my OS is Windows 8 pro. I can't connect to wifi but it displays connection available. When I try to connect to wifi, it shows this connection is not available. I also try to re install the driver wifi. but the problem is still on. What can I do now?

  Hi Francois,.

  Thanks for the reply.

  Thank you to try the following steps to solve the problem of troubleshooting.

  I need more information this problem so that I can help you better.

  1. Have you followed the steps I provided in the previous answer?

  I suggest you follow the methods mentioned below and check.

  Method 1. If you use a laptop, then I suggest you to check the key wireless keyboard that is on or not.

  Method 2 Try to reset the command netsh winsock via the command prompt.

  1. press Windows + X key and right click on command prompt (which must be run as administrator).
  2. Type "netsh winsock reset" and press enter (without the quotes).
  3. now restart the system.

  Try to follow these methods and response with the State of the question so that we can better help you.

  Thank you.

• Sites only show that connected primary vcenter.

  Hello. I'm under SRM with vCenter 5.1 5.1.1 update 1. Primary and secondary sites separated by a physical firewall. I followed the KB on ports:

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC & externalId = 1009562

  I tested with telnet and I can connect successfully to SRM primary vCenter over 80 remote and vice versa remotely SRM to primary vCenter. Each vCenter can communicate successfully with their own local server of MRS. more 8095. In the primary vCenter, I am able to successfully establish the reciprocity, and after that I am prompted for the remote vCenter creds, I see both sites successfully connected.

  Now, when I jump on the remote vCenter (recovery site) I'm able to establish reciprocity between the two sites, but when the prompt to enter creds for the remote vCenter (main site), I get an error that comes up as "Impossible to connect to the remote server.

  Not sure where the problem lies. Any help most appreciated.

  Thank you

  Hi Stefan. Thanks for the reply. Only, I solved the problem. I asked our guys to firewall to create a rule to recovery side vCenter for the side protected vCenter via port 80/443. Yes, for vCenter vCenter. As soon as this rule, he creates my side recovery shows two connected sites. Now, the strange thing is that under knockout of SRM firewall rules, there is no vCenter vCenter rule to:

  http://KB.VMware.com/selfservice/microsites/search.do?cmd=displayKC&externalID=1009562

  The only reason for which I asked him to add this rule was because for some reason that was open from protected to recovery (port 80/443) vCenter vCenter and the side protected SRM plugin has been successfully showing as connected. Probably a good idea to include this item for later use.

  Thank you

• Cannot download Web site at businesscatalyst host of muse, it shows the connection timeout.

  Cannot download Web site at businesscatalyst host of muse, it shows the connection timeout.

  Hello

  Please see the link below that has the same discussion.

  https://forums.Adobe.com/thread/1934384

  Kind regards

  Vivek