SIM not detected

Similar Questions

• Re: Portege Z830-11j - SIM not detected

  Portege Z830-11j I have this laptop... it's great.

  However, the supposed right drawer a SIM card is not detectable when it is installed.
  Is there some lack of software or another installation required.

  Can anyone help?

  + Message has been translated.

  Do you use this notebook with Toshiba preinstalled and preconfigured system Win 7?

  Have you changed anything in the configuration of the system?

  Module 3G is recognized in Device Manager?
  Please check this because due to lack and not installed 3 G driver, the sim module Ericsson would not be recognized by the system and the inserted sim card could not be processed.

• BlackBerry Z30 sim not detected after security wipe

  Hello

  My unlocked Z30 BB does not detect the sim card after security wipe. I did hard and soft reset, but the problem still persists. Today I took it to the service center and the guy told me that the sim connector pin is defective. How could he say that without inspection? To my surprise, he also informed that I need to replace the motherboard. Can someone please give an overview on:

  ++ If these questions have been seen on Z30 (I've seen for Z10) where security wipe cause the SIM to go unnoticed?

  ++ If security wipe and connector are correlated?

  ++ The worst case if the sim card connector is broken, fill out the motherboard needs to be replaced? (I know its 80% of the cost)

  ++ Is there anyway I can defend higher up in the service center

  Troubleshooting:

  > same sim works in any other mobile phone

  > no sim card works in Z30

  > The used micro sim card is the standard sim and not cut manually.

  > Reset multiple hard / soft / volume up and down reset button did the test (equivalent to removing the battery).

  I am based in India, in Bangalore, and the unit is under warranty (only 4 months). Name of the service center is Redington India, Cunningham road, bangalore.

  Any pointer is appreciated. Thanks for your help!

  Kind regards

  Imran

  A wipe destroy a physical component such as a SIM Slot

  It's just a coincedence

  Location SIM can be bought online, but you need to know how to solder.

  I see some listed on ebay for $4 USD

• Card SIM not detected blackBerry Smartphones

  Since the application of the first PRIVATE update we continue to receive message SIM card not detected.  Seems to drift in and out of the connection to the cellular network.  What could be the problem? Jumping is not a behavior even so the Rogers network signal is fine.

  Obviously seems to have worked - remove the SIM and put it again.

• SIM is not detected...

  I brought a flipkart x motorcycle and went up to my normal size SIM minced in a sim of nano. The SIM card is not detected on 3rd day morning. I reinserted the sim card and it was beautiful once again. 4th day, Sim become again detected and even after reinserting the sim card and the phone restarted, he remained unnoticed. Therefore, I used my old phone HTC Explorer with the same SIM card and it worked very well. In the evening, when I inserted the SIM in Moto X, it worked fine again. On the morning of 5th (which is today), returned SIM not detected, it's now evening and always the SIM card is not detected but same sim works fine in my other phone?

  Might need to get a new SIM from nano. It's funny how it works in one phone and not the other.

• BlackBerry not detected Passport SIM card

  Hello

  I bought a BB passport of a friend a few weeks ago. He started to work perfectly, I like the phone, it has...

  Since 2 days... the nightmare began! SIM NOT DETECTED. No network... technical problem...

  My SIM card is new and I've tried it with other devices, and it works well.

  When I restart the phone, the network seems to be ok... after a while, SIM CARD NOT DETECTED...

  Can someone help me get an idea about it! I'm really disappointed to have this phone of beauty that sucks!

  :::

  Thank you

  Thanks Artur72!
  Its just wired gor, after several reboots, putting out / Sim Card, ample, I almost tried... the solution is quite strange:
  I put a small part of the paper on the back of the SIM CARD... and. Halilouliaaaaaaaaa it works!
  big problem of someho got a easier simpler solutions

• one of my sites for card has stopped working... "" It is said "'slot 2, no sim card detected.

  I went on vacation and one of my cards continued roaming... but it does me not phone outside then I swipe the card and put back in the thought that will fix it... but now my phone will not recognize card in the slot to card... says "'slot 2 No SIM not detected"... but if I put the same sim card in slot 1 it works... (the problem why my card was not working was that I was signed up to the wrong network)

  It is a question where my phone should go to fix or can the phone repair... I see there is a sim Toolkit applications... This will fix

  You can transfer files from inside out by using your PC, USB connection and copy and paste the

  or

  using Manager file by default on your phone, press and hold to select files and then choose copy, access the external SD card, then select copy.

• BlackBerry Q5 network blocked due to sim not valid

  Nice day! I had a problem with my blackberry SQR100 q5-2, my first sim card in the device was sim Smart Communications and it works fine. After 6 months I switched to Globe Telecom 3 weeks of use, it works very well also. But recently I received notification "NETWORK LOCKED" after that I can't use my phone, it always says "Insert Sim/Sim not detected" I wipe data, reset time and nothing happened. I also put my Smart Sim and still does not work. When I checked the SIM card settings "device is ready to be used on the network" but I can't use even for another sim card. pls help thank you.

  Reload your operating system all first using BlackBerry link. Then, if she is still unable to read your SIM card, it is probably a hardware problem. Follow what is recommended above, contact your dealer.

• Portege Z10t-a - SIM card is not detected after Win 8.1 upgrade

  Hello world

  I have a Z10t-A. Portege Toshiba Pro win 8.1 recently, just upgraded to 8.1 Win.
  Before the upgrade, I could use the sim card to connect to the VPN, but since the upgrade the sim card not detected. I use an application called "AirCard Watcher".

  I tried the latest version of the driver 'EM7305 '.

  Visit the page of the Toshiba UE driver
  http://www.Toshiba.EU/innovation/download_drivers_bios.jsp
  Choose here:
  Laptop
  Portege
  Portege Z series
  Z10T-A Portege
  All the
  8.1 Windows 64-bit
  LTE pilot

  Now you should see two pilots LTE (5.2.1401.4045 and 3.5.1308.3911)
  I recommend you test the two drivers.

  Before you start the installation of the driver, the former current driver should be deleted.

• Sims 3 (win7) and "device 0 cannot run this title, no video graphics card supported not detected."

  Hello

  I just got the Sims 3 for Christmas, and I can't get it started.

  I just bought a new p7-1126 of hp computer that meets all the reqs as documented on the site of AMD System. (win7 64 bit, 1 TB hd, 6 GB ram, amd quad core 2.4 GHz processor)

  This computer has an amd radeon hd 6550d graph with / 3 gb (I think) (which is more than 128 MB recommended)

  and the drivers are up to date.

  I get the error message "device 0 cannot run this title, no video graphics card supported not detected" and I can't seem to do anything to solve this problem.

  I've uninstalled and reinstalled the Sims3 deluxe/ambitions three times now, with the expansion of ambitions installed so the third time.

  I did a lot of other things as suggested in line when I did research but nothing works.

  Help is appreciated and I hope we can get this fixed a problem. Thank you!!

  Hello

  Please provide information of the log of the event viewer.

  Information on the Event Viewer log shows that there is a problem with your memory (0xc0000005 error code).

  I suggest you run a diagnosis of memory on your computer and check if all goes well.

  Click on the links below and follow the instructions on the article to test memory on your computer.

  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-know-if-my-computer-has-a-memory-problem

  http://Windows.Microsoft.com/en-us/Windows7/diagnosing-memory-problems-on-your-computer

  Provide us additional information. So that we can help solve you the problem on your computer.

  Hope this information helps you.

• Elitepad 900 microsd card not detected

  I'm having a problem with the use of the microSD integrated on the HP ElitePad 900.

  The Microsd card works on my laptop and works on the ElitePad when using the jacket of the expansion.

  When I insert the micro SD card into the microsd slot on the back on the Elitepad next to the 3 G SIM, Windows 8 does not detect the card.

  I'm using a Kingston 32 GB SDHC card.

  I solved this problem by buying a Kingston 64 GB SDXC card. This card works perfectly.

  I don't know what's the difference between a card SDHC and SDXC card, in addition to speed? The ElitePad seems to be only able to read a large map if it is SDXC.

• CD drive is missing or not detected

  Good if I did a lot of research through forums on this problem already, none of the advice has helped me. But there is also another factor involved in my problem so I thought I should talk about my experience. I hope someone can give me some advice.

  First of all, I have a HP Pavilion dv9700. I often play the Sims 3 on my laptop. Which means every day. My laptop has overheating problems, so I bought a stand with a fan in her lap. It helps somewhat but not completely. So sometimes my computer shuts off when it overheats and I think that the reason my CD player does not work is related to it somehow. I played the Sims 3 on my computer and of course, it has overheated and it just stopped on me. When I went to turn on of course I had to restart the Sims. Well, it was not as simple as that. Whenever I tried to load the Sims he would say something in the sense of "Cannot start game when already played" - something like that. Once, he actually does not play for me, but my computer is hot so I turned off and when I tried to play again it woudn't work. Since then, I have tried everything to fix my drive, none of the work methods suggested for me and when I run the fix of Mr. program he can't help either, it just says that my CD drive is missing or not detected. I am so at a loss for what to do. And I know that a lot of people have this problem, but I thought that my situation may be other factors involved. If all the tips that can help me are greatly appreciated!

  Hello

  Clogged or blocked vents? The internal fan is working correctly? Doesn't look like
  everything is as it should be in the Department of ventilation. Clean as much as possible, and even if it's awkward
  Try a good fan blowing through the vents as a test. This should be very telling. If the internal fans
  are not all work as they should, or the ventilation openings are blocked, then a whole or several parts of
  the device can get too hot and either acting strangely or stop completely.

  Check with the HP Support and forums for known issues.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ===========================================================

  Help for the problem of CD/DVD but the heat might indeed be the main cause of the issue.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Time Machine (on Mac) does not detect the airport Time Capsule

  Originally posted on the page of the airport, but seems to be the better question for this group. Sorry for the double post

  Looking for advice on how to get the Time Machine utility for access to my Time Capsule. I use an iMac in late 2012 with MAC OS 10.12 TimeCapsule is 2015 7.7.7 running latest firmware. Airport utility is the latest firmware 6.3.7.

  When I run the application Time Machine, Time Capsule is not detected. I tried the two WiFi and with cables connected Ethernet (not tried USB yet) and my Time Capsule doesn't have a lightning bolt or firewire ports.

  Open Airport utility & see the airport time capsule. I can see all connected devices, including the MAC, but no prompt activation Time Machine on the Time Capsule.

  I recently used TM on this iMac with a G-Technology drive. It auto detects the time machine and executes a back up. But airport Time Capsule will not.

  Any suggestions?

  Sierra has been problematic with the TC.

  1. make sure you don't have any charge virus protection software. In fact, I would say that disable all software 3rd part at the moment.

  2. make sure that you can actually write to disk of TC.

  Attach the TC disc in the finder and copy a file on disk, you can delete it later... It's just to ensure that you have full write permission. If it does not for the most part, you won't be able to use Time Machine... If you can then try TM immediately...

  Just to be clear, the TC is a network device. You have tested with ethernet and wireless... Ok.. They are only suitable methods. You cannot use USB. And clearly, TC has never had nor will never be ports Firewire or lightning.

  3. no chance that a reset complete TC. This will not delete the files on the hard drive, but you must make sure that the device is configured on the current computer.

  4. There are many positions in these days... read through them and do some research. Sierra is a bleeding edge new... So wait you to spend a lot of the precious liquid if you choose to be an early adopt.

• my ipod is not detected by itunes

  Hello, so, as it is said, my ipod is not detected by itunes and it s not because taking usb does not work or has problems because it becomes a hard drive on my computer.

  I have tried everything but nothing works:

  I have reset my ipod and itunes, uninstalled, re installed, turn and turn on my computer and itunes and my ipod as well, I tried only everyt things written on the internet.  as I completely cleaned my ipod it, but now I'm stuck because I can t get my music back.

  and nothing worked, so I'm really frustrated and really need help please

  Thanks /.

  What is an iPod touch?   IPod touch does not appear as a USB storage directly on your computer.  An iPod nano can appear there.  The current nano iPod looks like this

  

  Also, is your computer running iTunes on a Mac or Windows PC?  If Windows, which free?

• Drive external DRIVE not detected after update of the Sierra

  I upgraded my Macbook Air Sierra this morning. Since then, whenever I plug in my external Seagate HDD, it is not detected in the Finder, or see a shortcut on the desktop. However, it is visible in disk utility.

  I connected the HARD drive even air to my friend Yosemite running, and it works as usual.

  How the drive is formatted?

  Post a screenshot of what you see in disk utility.