simulation does not work

I composed a few diodes the wizard of components, such as the diode acts like a switch perfect to 0.7 volts.  For some reason any SPICE simulation does not run.   If I include one of these diodes in other circuits, the circuit will not simulate.  The diode model is the problem.   Any ideas how to operate?  Attached is the file multisim

Thanks in advance!

"- Checking SPICE netlist for perfectbridge - Thursday, February 5, 2015, 11:51:34-"
= SPICE Netlist verification completed, 0 error (s), 0 warning (s) =.
Model 'diodeperfect__perfectdiodes__1': 'IS' parameter must be greater than zero
doAnalyses: incorrect use of the parameters of the model
Cancelled simulation. "

So: right-click on one of the diodes, select 'Properties' - 'Value' tab - press "Change model" button - box 'Use default' for 'IS' - press "Change all 4 elements" - press "OK".

Tags: NI Software

Similar Questions

  • Microsoft Flight Simulator does not work

    My husband is having a problem with his flight simulator.  After that, it installs the software, it is able to play.  However, after this first piece, once he leaves the program and try to open it again, it will not load.  The programs displayed on the hard disk but does not work.  It uninstalled and re installed the program, with the same result.  After the initial piece after installation, it is not able to play again.

    Hello

    Here is a link that should prove beneficial to get a resolution to your inquiry.  I hope that this information is beneficial.

    http://social.answers.Microsoft.com/forums/en-us/vistagaming/thread/24974b97-BCEE-46EA-8f52-f7ad0881125a

    Thank you

    Aaron
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think

  • a window said "flight simulator does not work with your video card. Make sure you have the latest drivers installed for your video card.

    Flight Simulator X not would allow me to get it because it says I need to update the video card. I think the problem was that I finally erase all memory of the computer using a special cd, because once I have done this and downloaded the software again, it stop working

    Hello el 24, welcome.
     
    There are a few possibilities as to why you see this message. There is a chance that you do not have your drivers graphics/display installed or configured correctly.
     
    We will need to know the brand and model of your computer to properly route you to the right path.
     
    Once we have this information, we can see if we can provide you a link to the Web site of the manufacturer of your PC to download the driver.
     
    Let us know,
     
    Thank you!

  • Plugin Eclipse Simulator does not work correctly.

    Hello

    I have a problem with my eclipse + JDE plugin.

    Whenever I try to run my widget in the Simulator in view Manager service tab, I can see the Blackberry Simulator service enter the status of"ex". But once the Simulator is started, the status of the Simulator Blackberry stay in 'Start-up' then I can't start my application and I get a warning message stipulating the lance Simulator.

    I try to run a clean.bat in the directory of the Simulator, but this does not solve the problem.

    What is the problem? Should I reinstall the plug-in?

    Thank you.

    FOR INFO:

    Install Eclipse version 3.5.1

    The plugin JDE version: 2.0.0.201003191451 - 33

    Hello

    Thanks for this reply, but I already tried and it did not run.

    So I reinstalled all the Eclipse and plug-in to solve the problem!

    Kind regards.

  • the blow of high Simulator does not work after the launch

    OK so maybe it's a bug... but its starting to become annoying... when I run the Simulator I can use until return to the fine menu... but when I opened the app and start using them, the function stops working! the strange thing is the slippery side works so I can switch between loaded... applications always is there anyone else having this problem?

    I've seen a variety of problems in the 0.9.4 Simulator involving swiping.  I had what you call, and I think could even slide-side (I couldn't have other apps open, but I think he did always normally the app briefly go to 90% of the size).  I also had failed several times, system status bar which means upper left and upper right slide stop working and the settings are not accessible from the Navigator view (assuming that I can get there).

    It seems that in these cases, there is nothing to do except reboot the Simulator.

    I have not yet noticed a correlation with all that I could do that would create.

  • Simulator does not work!

    Salvation;

    I'm color with a strange problm: as my Simulator to send me an error when I run it jvm error 104: eception, this probm is not in the program, because I tested with a sample of word Hello but it gives me the same error, I have serached in the forum, but the solution is to recognize the code, for me really I don't know what is the problm this error at the beginning I can't join my Simulator

    in your opinion, what is the probm?

    Thank you very much

    clean the Simulator. If the problem persists, run the clean.bat located in the bin directory.

  • MDS BBM Simulator does not work (throws an exception)

    I try to use the BBM SDK Beta v1.0 but I have problems with the MDS Simulator.  I followed the quick start guide that is included in the download.  While trying to start the MDS Simulator, I get this exception:

    Yes, we have solved the problem.  I had to install the correct version of Java SE JDK (1.6.0_20).  Then make sure to copy the files from the folder security.  Finally, make sure that your environment variables are set correctly (for example. JAVA_HOME)

  • Blackberry 10 Simulator does not work

    Hello

    My blackberry Simulator is starting and just paste it here (in the screenshot), what accusation and everything, but there is

    Thank you

    And have you tried the instructions to turn on hardware virtualization?

  • 10.2 PushCollector example does not work

    Hi, I tried to compile and test the PushCollector example for 10.2 SDK but I does not compile properly and the message did not provide sufficient information to be able to fix it.

    Examples of projects are at this location: https://github.com/blackberry/Cascades-Samples/blob/master/pushCollector/10.2/

    E:\bbndk-beta\host_10_2_0_15\win32\x86\usr\bin\ntox86-ld: jump incompatible... /... /pushCollectorCommon/arm/libpushCollectorCommon.so in the research - lpushCollectorCommon

    make [2]: leaving directory E:/area of work/pushCollector / x 86

    make [1]: leaving directory E:/area of work/pushCollector / x 86

    E:\bbndk-beta\host_10_2_0_15\win32\x86\usr\bin\ntox86-ld: could not find lpushCollectorCommon.

    CC: E:/bbndk-beta/host_10_2_0_15/win32 / x 86/usr/bin/ntox86-ld caught signal 1

    make [2]: * [o-g/pushCollector] error 1

    make [1]: * [debug] error 2 make: * [Simulator-Debug] error 2

    Sorry, I'm noob in developing c ++. Is it possible by using various projects such as libraries? I have not used before projects before library in c ++ and I do not know how to configure them properly.

    It is possible to use this library with an absolute path?

    https://github.com/BlackBerry/Cascades-samples/BLOB/master/pushCollector/10.2/pushCollector/.cprojec...

    I was able to run the example.

    The order in the sequence of generation is very important. When I built the correct order, that I was able to correctly generate the package of the project PushCollector and then I could deploy on the device. The sequence is, in case anyone has the same problem:

    -Clean all projects

    -Create a 'pushCollectorCommon '.

    -Create a 'pushCollectorHeadless '.

    -Create a 'pushCollector '.

    -Run 'pushCollector' to the device (I used a Dev Alpha B with 10.2.0.1445, the Simulator does not work)

  • I just dug my copy of train simulator, and it does not work on Windows 7 64-bit. Ideas please

    I just dug my copy of train simulator, and it does not work on Windows 7 64-bit. Ideas please

    Thank you very much for all your suggestions. "Iwent with."

    This can help with some (but not all the) programs/drivers:

    (1) uninstall the program, if it is already installed. Then when install you / reinstall instead of double click on the Setup file, right click and select 'resolve compatibility issues.

    (2) then click on 'Try recommended settings' and in the next window, click on "Start the Program" to install it.

    (3) after he set up see if it works properly. Note: some programs may not be able to run in Windows 7.

    and it worked.

    did anyone tried the version updated? I read some rather disappointing reveiws.

    Once again my kind thanks for all your suggestions

  • Microsoft sidewinder gamepad 2 does not work on the Combat Flight Simulator WW11 and Europe series

    Original title: I have the Combat Flight Simulator WW11 and Europe series. My microsoft sidewinder gamepad 2 does not work on my XP and my Windows 7 computer. The joystick works on CFS2 Pacific. Help, please.

    I have a HP Pavilion p6717c with a radion HD 6900 graphics card. With windows 7 home

    Hello

    1. don't you make changes to the computer until the problem occurred?

    2. you get any error message?

    I suggest you to see link below and check if it helps.

    You experience problems when you use a Sidewinder Force Feedback Pro joystick with Flight Simulator on a Windows 2000, Windows XP, or Windows Vista-based computer: http://support.microsoft.com/kb/294672

    How to fix game controllers in Microsoft games: http://support.microsoft.com/kb/831361

    Items of Combat Flight Simulator: http://support.microsoft.com/combatflightsimfaq

    Also I suggest you to send your request in the below link.

    http://www.Microsoft.com/games/en-us/community/pages/forums.aspx

    Hope this information is useful.

  • My Logitech extreme 3D pro joystick does not work with the dogfight when played on vista Simulator.

    Why can I not get my joystick works when you play the air combat Simulator?  I'm under the it on my laptop with vista.  The game installs fine, but I don't get a response when I use the joystick which is a Logitech extreme 3D pro.  I go into the settings to calibrate it and it shows that it is there and it tests fine but it still fails.  I thought it was just the joystick, but it works with the microsoft x Flight Simulator.  Then I tried to install the joystick Saitek initially, I used to play the game with and got the same answer, it would not work and settings would recognize the control stick and he would test well but still does not work.

    Hello

    Welcome to Microsoft Windows 7 answers Forum!

    It seems that the joystick drivers are not updated for windows Vista.

    Try to access the link below and install the gamepad for vista drivers and install the same as an administrator.

    http://www.Logitech.com/index.cfm/441/291&Hub=1&CL=GB, en? DiSo = 13

    If this does not work, try to contact Logitech and check if they have updates on this for Vista.

    Follow the link below for more information.

    Combat Flight Simulator 3: how to troubleshoot joystick

    http://support.Microsoft.com/kb/811463

    Hope this information is useful.

    Thank you, and in what concerns:

    Suresh Kumar-Microsoft Support.

    Visit our Microsoft answers feedback Forumand let us know what you think.

  • Microsoft Flight Simulator 2004 installation with the 4th vista disc does not work. What should I do?

    Microsoft Flight Simulator 2004 installation with the 4th vista disc does not work.  What should I do?

    Hello

    You get no matter what error code or error message?

    There seems to be a problem with the file missing in the rear disc system. I suggest you to refer to the following Microsoft article and check if it helps.

    Flight Simulator 2004: known video issues: http://support.microsoft.com/kb/823628

    If the steps in the Microsoft article mentioned above do not help, then it would be best to ask your question in the Microsoft Game support forum.

    Microsoft Flight Simulator Games Forum: http://www.fsinsider.com/

    Or contact support for Microsoft Flight Simulator game: http://www.microsoft.com/Products/Games/FSInsider/tips/Pages/default.aspx

    Hope the information is useful.

  • command Simulator "StringInjection" does not work with SureType keyboard

    Hello

    I use the Simulator command 'StringInjection' to simulate keyboard input. However, it does not work with SureType keyboard.  Still, it appears a list of suggested words, which make the string injection stops. Is anyway to avoid this?

    It is the expected behavior.  StringInjection simulates typing on the keyboard, what might trigger a prompt SureType.

  • 10.3 simulator Rotation does not work?

    I'm testing an app on the Simulator. I use the controller to change orientation, but nothing happens. It runs on a device.

    The Simulator does not support rotation?

    Works for me trying to touch the lower right corner.

Maybe you are looking for

  • iTunes will not save work of film

    I use the latest version of iTunes 12.4.2.4 and I can't seem to save the work of film. I add to the tab work getinfo and it display.  Once I click OK it won't save the metadata.  I'm so frustrated.  I want to just junk from apple to work as advertise

  • Win XP SP3 hangs on Tecra S3

    I tried to install Windows XP Service pack 3 on my Tecra S3, and it fails (stops indefinitely) at the stage of "current execution after the installation process".I tried to do it via windows Update and also burning full ISO image, "Clean boot" mode,

  • How we can use Apple Watch remote keynote on iPad?

    Hi all! I prefer to use Keynote on the iPad when I have a presentation. Can we use Apple Watch remote slides on the iPad? It is really practical if possible.  How can we do?

  • The development of fly

    Hello. I need to create a contextual action in my VI and to appear above all other applications - fly goal. In research, I saw as C++ and CVI there are a of functions for this kind of problems. But I was looking for invoking and nodes of property dem

  • IMAQ Status.vi

    Hello I have a few questions on the functioning of the "IMAQ Status.vi".  There is another similar question back in 1994, but it was not answered, and I'm having the same problem. What I try to do is run a sequence repeatedly, to a scanning applicati