Simultaneous recording of time and strain

I use LabView 2010, NI USB-9219, NOR cDAQ-9172 and linear strain gauges. I want to be able to save time for each reading of strain and can't seem to find a method that works. I want the result in Excel to time and strain. I know that the value of the strain itself is correct as being verified experimentally, I just need the corresponding to add in the block schema component. Any help would be greatly appreciated as I am new to LabView.

rumef,

You can add a time column to the file in the configuration of the writing on a file of measures.  Double-click the function to set the parameters.  You can also find addign a useful header.

See attached sscreenshot.

Dan

Tags: NI Software

Similar Questions

  • Tecra M5 does not record the date and time - battery RTC or CMOS checksum is inconsistent

    My Tecra M5 PTM50E reverend new does not record the date and time. I loaded RTC battery for 8 hours when electricity is on in the said user's manual. I don't know where is the problem. The BIOS settings are respect after power is on.

    When I change any value in the BIOS, the changes are saved properly but date & time system restored to their value 01/01/2000, 00:00 every time when I get out of turning off more of 2-3 min. Message "RTC battery is low or CMOS checksum is inconsistent.

    Press [F1] to set Date/time"does not appear when I power on the computer. Any suggestions?

    Hi guys

    Usually this problem appears only if the CMOS (real time clock) battery is empty or corrupted.
    The real time clock battery powers the internal clock in real time and calendar. It also maintains the system configuration. If the RTC battery is completely discharged, the system loses these data and the real-time clock. In this case, the message RTC battery is low or CMOS checksum is inconsistent appears.

    So I see only two possibilities:
    Either you will charge the battery for real-time clock, or you ask the technician for replacement.

    Generally, the battery must be completely charged after 8-9 hoers but try to connect the laptop to the power adapter for a long time.
    If it will not help solve the problem if you contact the ASP for the RTC battery replacement.

  • I recorded annual plan and you paid every month since November 2015. But because of the pregnancy, I can't use adobe more at this time. Can I Cancel to pay after next month, or are there other ways? Please let me know.

    I recorded annual plan and you paid every month since November 2015. But because of the pregnancy, I can't use adobe more at this time. Can I Cancel to pay after next month, or are there other ways? Please let me know.

    Hello

    Please refer to cancel your Adobe Creative Cloud membership

    If you need to contact support technical assistance

    Contact the customer service

    Concerning

  • My iphone 6 does not light, I held the home button and power at the same time and no vibration or no sign of life, any suggestions as to what it could be would be appreciated

    Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

    Marley6921 wrote:

    Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

    Put it on wait ten minutes if the phone did not come one, then hold down the sleep/Home button until you see the apple logo and then release, make sure that the phone is still connected to the charger.

  • Trigger digital beginning for simultaneous tasks of HAVE and AO

    I am trying to create a Subvi to simultaneously measure 5 signals of HAVE and an AO output signal.  The AO signal feeds a diet that feeds in turn my sample.  It HAVE the applied voltage, current temperature measurement (via a shunt resistance), via a V 1-5 of a pyrometer optical signal and two other sensor input voltages.  During the test, I would also like to vary the applied voltage, so I set up a ripple of tension values.  To make things pretty simple I execute the tasks of HAVE it and AO at the same pace, and I want the two tasks to start at the same time.  To reach the start of the trigger, I wired an additional set of contacts on the power relay to line 0 on a DIO 9401 resident module in slot 5 9172 chassis (access to the PFIO signal).

    Attachment is the base Subvi, I came with to do so.  I think it is the task of the AI seems to trigger correctly, but the AO seems to start as much as 100 msec before the start of the task to HAVE it (sometimes it is dead on, but other times not).

    Will I put in place these tasks to start at the same time, or is my approach to programming off?

    Here's my hardware configuration

    1. If you want to start both tasks at the same time and run synchronously, you don't need two digital triggers start. Take a look at the example of Multi-Func-Synch AI - AO.vi in the Finder of the example.

    2. Design your architecture using the State machinery rather than using the Structures of the sequence. Take a look at a model of State machine in the file-> New...

  • The relay through time and Total flow control

    Hi all

    I'm relatively new to Labview and have worked on a great program from lately, which uses a Module with my cDAQ-9178 OR relay SPST 9481 to open and close the 3 different solenoids. The program should open at a specific time and leave it open until a certain amount of flow is passed through them. I already finished the programming to record the total flow through the valves, and after many hours past the forums I found a way and changes in the code that turns on the relay based on the amount of time spent searching, however it turns on the relay and leave them on until the 'period' are filled then pass on the next round. I need to change this option further so that it lights when my "Cycle Start Time" is reached, turns off when reaching the set amount of flow for this cycle and then continues to wait until the next "Cycle Start Time" occurs.

    I imagined a way to proceed would be; by eliminating where departures from the clock a new cycle each run and just have it constantly by comparing the time of "Initial start (run)" 'Start' time sequence (when I push the start sequence and actually start to opening the relay). Then change the "delay" to 'Cycle start time' and the (> =) function to a function (=). So now, it begins after the elapsed time is equal to the start time of Cycle. Certainly, this opens the questions, because currently, at the beginning of the cycle the command of the relay begins. So I need make my comparison outside the case 'Cycle' or move the control relay in the case of 'true/false '. However, then I run the question of how to get the software to change the case once he saw to stop the relay.

    As you can see, I have about 1 million different things in my head that I played with. Advice or assistance to get me on the right track, or you know of examples would be great! My code is attached below, and I'll post a photo after this post about how I'm taking care to record the total flow. Thank you for your time and help!

    Hi M_Blaylock,

    You mentioned that you are relatively new to LabVIEW. Are you familiar with some of the debugging tools?

    http://www.NI.com/getting-started/LabVIEW-Basics/debug

    Turning on climax execution should allow you to see the data flow through your schema. Also, probing the wire just before the input case structure should allow you to see what data is actually trying this case selector. If you get unexpected data, you can probe the front steps to see source these unexpected data.

    I hope this helps and good luck with your code!

  • I have an old laptop running XP. It has clogged up big time and need to wipe and reinstall XP. I have no disk.

    Hello

    I have an old laptop running XP.  It has clogged up big time and need to wipe and reinstall XP.  I have no XP disc, but have a license number on the details of the system window.

    I can't find a recovery partitionand can not find anywhere to begin the creation of recovery disks.

    I've defragged and cleaned files.  I did a registry clean not long ago who did nothing.

    It was originally my husbands laptop and sat on the shelf unused for 3 years.  We now use for recording and playing music only and don't want no other programs about this other than the music software and a pack of office (which we have).  I don't even think it should be connected to the internet, because I'm afraid that the updates could corrupt the old programs that we will get on it once sorted.

    I can give Microsoft license number so that they can send me XP?

    Does anyone know if I need to rethink the connection through the web?

    Any other advice?

    Thanx

    Glenys

    Contact the manufacturer of the computer.  As the OEM licensed dealer, they had to provide you with a way to restore the computer to its default settings.  You may need to pay for it now.

    General cleaning of the registry nothing if you try to fix something specific, then you usually just fixed this specific thing.  ;-)

    What edition of Windows XP?  Home, professional or Media Center?

    If you have a generic _ Windows XP edition CD corresponding to the product key on the machine sticker (there should be a given, it's a laptop) you may be able to use this generic CD with this product key (or * perhaps *- but not certainly) product key, you can remove the machine using something like Belarc Advisor.

    Best bet - call in the manufacturer.  I doubt that it is out of business, but if they are: How to replace software or hardware, packs Microsoft service to order and replace product manuals

  • Problems with recording / playback volume and record length

    I turned up the logging level in the in the Audio section on the Control Panel, but that sound recorder (Windows) in entertainment relit at very low volume.  My headset with microphone and speakers work very well for Skype calls, so I think that the microphone is ok.

    Also, is it possible to save more than a minute?

    Thank you

    Hello Tjansen,

    Thank you for your message.  Please, try the following steps:
    Double-click on the taskbar of the speaker icon > click on 'Options' > select 'properties '.
    Make sure that the 'Micro' and 'PC speakers' have check marks.
    In addition, ensure that your output device and Microphone are not silent by displaying the mute boxes on each category
    You can then adjust the volume coming out of your microphone with the volume slider, you can adjust the bass etc.
    To do this, click on 'Options' > select 'advanced controls '.
    With respect to the registration of more than one minute, you can follow the steps below as a workaround, or you can download a 3rd party program that performs the actions you have requested.
    Allow the recorder record silent for 60 seconds.  Click 'Edit' > 'Copy' > click 'Edit' > 'Paste' > 'Insert '.
    This will add 60 more seconds. Click on "Edit" > "Paste" > "Insert" as many times as you need. Save as a file 'model' (name it something like long record.wav)
    Then, when you want to save something for more than 60 seconds, open the long record.wav file and instructions on the existing (virgins).
    Make sure that you save the new record with a new file name.

    Please let us know if it did or did not help to solve your problem.
    See you soon

    Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

  • Time and Date Z30 blackBerry

    Dear friends

    What is the problem with Blackberry Z30 whenever I restart the phone even for seconds, the date and time reset to Mar 9 and the time of 3:45. How can we challenge any idea. It does not seem to recognize the self... It's ruining my system and appointment call recorder.

    I'm sure that this is not a toy

    Questions, suggestions...

    Go to settings > Date and time.

    Zone to check and correct if necessary.

    Recommend Auto update time zone at the prompt. You never know when the mobile network will transmit the wrong time zone and your alarm goes off at the wrong time. But now, for troubleshooting, look and see if the time zone is correct, and look for you prompt to accept the change.

    Allow to set a Date and time automatically.

    If the problem is not the time or time zone is transmitted by the network or the BlackBerry seems to react to the time signal mobile network, then I would look at possibly conflicting software apps, corrupted and that sort of thing. It may be easier to just make a clean OS and then move forward a step at a time and that you restore the data and install test applications.

  • My mac had to be repaired several times and eventually I was forced to restart the entire computer, wiping everything.

    My mac had to be repaired several times and eventually I was forced to restart the entire computer, wiping everything. I registered my purchase CS6 Design Standard of two years, so I have the serial number, but I don't have the record of the initial purchase. How do we install CS6 on my practically new Mac?

    [Duplicate message deleted... post the same question more than once is confusing... MOD]

    ADDITION to previous versions http://www.adobe.com/downloads/other-downloads.html can help

  • How to record audio Microphone and PC?

    I've been looking for everywhere tutorials on how to do it, but don't can find videos of audition 3.

    I want to record my mic and PC audio at the same time (Yes, my PC supports "Stereo Mix").

    Thank you!

    Just hearing records everything that is given by your sound card or audio interface so you don't have to sort the parameters he who send the microphone and the audio PC to the record side of your system.

    How to do this will depend on exactly what your audio device and how you set the ranges.

    Once you have the end of the sound card put in place, the hearing is easy though.  Go to hardware edition/preferences/Audio and, if all is good on your sound card, it must appear as an option in the menu dropdown for entry 'default'.  You can also route the default output however you want to listen to things.

    A couple of points... the 'Device class' box allows you to specify the type of driver you are using.  Unless you have a specialist audio interface, it'll probably be Ms. also, the sampling frequency that you define in hearing must match what you set when you were selecting things on your audio card/interface.

    I don't want to end on a Downer, but many sound cards these days this force you to save on the thing or the other and cannot make a mixture of sources like XP and earlier versions of Windows used to offer.  Maybe that's why you keep finding tutorials for AA3.0... it was the last version designed around XP and previous versions.   I hope you're one of the lucky ones.

  • How to get 2 xml (brother) of the tag even time and merge them

    How to get 2 xml(Sibling tag) content at the same time and merge them and find the value of the result in the indesign file with page number

    As

    account <>

    < a > This is a text < /A >

    a-123 < B > < /B >

    < / documents >

    First of all, we need to tag A and B value as:

    It is a text - a-123 and then get this form of text from indesign doc page number

    Help, please

    Try this,

    var root = app.activeDocument.xmlElements[0];
    var aTag = root.evaluateXPathExpression("//Record/A");
    var bTag = root.evaluateXPathExpression("//Record/B");
    for(i=0; i
    

    Vandy

  • CC does not refresh on my Win7 machine. I tried several times and it closes after update download and try to install. Downloaed new application from Adobe, downloaded, tried to install it and received the error 50. Help!

    CC does not refresh on my Win7 machine. I tried several times and it closes after update download and try to install. Downloaded new application from Adobe, downloaded and tried to install received error 50. Help!

    Hello

    as strange as it may seem I'm afraid it is a challenge for Creative tool Adobe cleaning of cloud.

    Sometimes - for some reason-CC "unwilling" work. In this case you should CC completely remove and reinstall by using Adobe Creative cloud cleaning tool. (A try to uninstall by own resources is not enough!)

    I quote:... helps resolve installation problems for Adobe Creative Cloud and Adobe Creative Suite (CS3 - CS6) applications. The tool removes the records facility for preliminary facilities of Cloud applications or Creative Suite creative. It does not affect existing installations of earlier versions of Creative Suite or creative Cloud applications.

    Please use: l http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.htm and follow the prescribed sequence of operations

    Sometimes, the "opm.db" file is the culprit. In this case, you must remove it.

    If necessary and for questions and so "open" Please use the cat, plus I had the best experiences.

    Hans-Günter

  • Group records with time

    Hi all

    This is our requirement.

    We must combine records with time.

    for example: period = 3
    TABLE: XX_SALES
    ---------------------------------------------
    XDATE XQTY
    ---------------------------------------------
    10 5/1/2012
    20 2/5/2012
    3/5/2012 30
    4/5/2012 60
    12 2012/5/7
    8/5/2012 23
    45 8/5/2012
    100 12/5 / 2012
    5/2012/13 55
    5/2012/15 99

    == >
    ---------------------------------------------
    XDATE XQTY
    ---------------------------------------------
    1/5/2012 10-> 5/1/2012 Group (5/1/2012 ~ 3/5/2012)
    2/5/2012 20-> 5/1/2012 Group (5/1/2012 ~ 3/5/2012)
    3/5/2012 30-> 5/1/2012 Group (5/1/2012 ~ 3/5/2012)
    4/5/2012 60-> Group 5/2012/4 (4/5/2012 ~ 2012/5/6) *.
    7/5/2012 12-> Group 5/2012/7 (5/7/2012 ~ 9/5/2012) *.
    8/5/2012 23-> Group 5/2012/7 (5/7/2012 ~ 9/5/2012) *.
    8/5/2012 45-> Group 5/2012/7 (5/7/2012 ~ 9/5/2012) *.
    5/2012/12 100-> Group 5/12/2012 (2012/5/12 ~ 14/5/2012) *.
    13/5/2012 55-> Group 5/12/2012 (2012/5/12 ~ 14/5/2012) *.
    5/15/2012 99-> Group 5/15/2012 (15/5/2012 ~ 5/17/2012) *.

    After amount to combine with period = 3, the result will be
    ---------------------------------------------
    XDATE_G XQTY_G
    ---------------------------------------------
    60 1/5/2012
    4/5/2012 60
    2012/5/7 80
    12/5/2012 155
    5/2012/15 99


    Here's the example script
     
    create table XX_SALES(XDATE DATE, XQTY Number);
    insert into XX_SALES VALUES(to_date('20120501','YYYYMMDD'),10);
    insert into XX_SALES VALUES(to_date('20120502','YYYYMMDD'),20);
    insert into XX_SALES VALUES(to_date('20120503','YYYYMMDD'),30);
    insert into XX_SALES VALUES(to_date('20120504','YYYYMMDD'),60);
    insert into XX_SALES VALUES(to_date('20120507','YYYYMMDD'),12);
    insert into XX_SALES VALUES(to_date('20120508','YYYYMMDD'),23);
    insert into XX_SALES VALUES(to_date('20120508','YYYYMMDD'),45);
    insert into XX_SALES VALUES(to_date('20120512','YYYYMMDD'),100);
    insert into XX_SALES VALUES(to_date('20120513','YYYYMMDD'),55);
    insert into XX_SALES VALUES(to_date('20120515','YYYYMMDD'),99);
     
    We can solve this problem by using the loop now:
    to find the XDATE_G and it's rank in the loop and the XQTY in the range of the sum.
    DECLARE
      V_DATE_FROM DATE := NULL;
      V_DATE_TO   DATE := NULL;
      V_QTY_SUM   NUMBER := 0;
      CURSOR CUR_DATE IS
        SELECT DISTINCT XDATE FROM XX_SALES ORDER BY XDATE;
    BEGIN
      FOR REC IN CUR_DATE LOOP
        IF V_DATE_TO IS NULL OR REC.XDATE > V_DATE_TO THEN
          V_DATE_FROM := REC.XDATE;
          V_DATE_TO   := REC.XDATE + 3 - 1;
          SELECT SUM(XQTY)
            INTO V_QTY_SUM
            FROM XX_SALES
           WHERE XDATE >= V_DATE_FROM
             AND XDATE <= V_DATE_TO;
          DBMS_OUTPUT.PUT_LINE(TO_CHAR(V_DATE_FROM, 'YYYYMMDD') ||
                               '-----qty: ' || TO_CHAR(V_QTY_SUM));
        END IF;
      END LOOP;
    END;
    Is it possible to solve this problem by using analyze sql?


    Thanks in advance,
    Best regards
    Zhxiang

    Published by: zhxiangxie on April 26, 2012 14:41 fixed the grouping expected data

    There was an article about a similar problem in Oracle Magazine recently:

    http://www.Oracle.com/technetwork/issue-archive/2012/12-Mar/o22asktom-1518271.html

    See the section on the 'grouping beaches '. They needed a total cumulative who started once the total reaches a certain amount.

    You need a total cumulative which starts again when the date changes to group and the dates of beginning and end of each group must be determined dynamically.

    This can be done with the analytical functions.

    Here is a solution-based 'code listing 5', the solution MODEL, which is recommended in the article.

    SELECT FIRST_DATE, SUM(XQTY) SUM_XQTY FROM (
      SELECT * FROM xx_sales
      MODEL DIMENSION BY(ROW_NUMBER() OVER(ORDER BY XDATE) RN)
      MEASURES(XDATE, XDATE FIRST_DATE, XQTY)
      RULES(
        FIRST_DATE[RN > 1] =
          CASE WHEN XDATE[CV()] - FIRST_DATE[CV() - 1] >= 3
          THEN xdate[cv()]
          ELSE FIRST_DATE[CV() - 1]
          END
      )
    )
    GROUP BY first_date ORDER BY first_date;
    
    FIRST_DATE            SUM_XQTY
    --------------------- --------
    2012/05/01 00:00:00         60
    2012/05/04 00:00:00         60
    2012/05/07 00:00:00         80
    2012/05/12 00:00:00        155
    2012/05/15 00:00:00         99
    

    If you 9i, there is no function model. In this case, I can give you a solution using START WITH / CONNECT BY that does not work as well.

  • problem with the format of the time and from 12:00 am

    I'm using Acrobat 9 Pro. I have a pdf document to fill out on-line that I fell through the wizard and then modify by using "Add or edit fields" under the menu "Forms." I have a text field where the time is recorded (hours, minutes and am or pm). I have it in the format hh: mm tt, but if I come back at midnight, it goes to 0:00 when I tab out of the field. I am not allowed to use military time. Any other time I entered does not cause it. Anyone know how I can fix this so that it remains 12: 00?

    I understand, it seems strange, but it's like that. I'll guide you through what you need to do.

    1. create a new JavaScript to the document level. With the document open, select: Advanced > Document Processing > Document JavaScripts

    and add a new one. You can call it what you want, for example "DateFormat." When you add a new, it provides you with a skeleton of the default function. Delete and copy and paste the following text:

    function TF2 (ptf) {}
    If (! event.value) {}
    return;
    }
    var date = AFParseTime (event.value, null);
    If (! date) {}
    Event.Value = "";
    return;
    }
    var cFormats = new Array ("HH: mm", "HH: mm tt", "HH", "SS tt");
    var time_string = util.printd (cFormats [MFP], date);
    var zerohour_re = / ^ 0: /;

    Event.Value = time_string.replace (zerohour_re, ' 12: "" ");
    }

    function TK2() {}

    AFTime_Keystroke ("h: mm tt");

    }

    2. then you need to change the date field and specify a custom type and Format script. On the Format tab, select a category of "Custom" and you will see where you can write the script.

    For the strike script, follow these steps:

    Typing script

    TK2();

    To Format the script, follow these steps:

    Script format

    TF2 (1);

    These what call the functions that you configured in the script at the level of the document that you created earlier. Post again if you have any questions.

    TF2 altered function simply replaces the characters "0:" with "12:" if at the beginning of the string in the form.

Maybe you are looking for

  • Computer portable NB305 - Windows 8 pro - WIFI not working not

    Hello everyone, I have a Toshiba NB305-105 netbook with windows 7 and 2 GB Ram... I bought windows 8 pro update and I installed it. After the proper installation, I installed all the drivers toshiba Win 7 32 bit.Well, after that, no hardware problem,

  • How can I prevent my firewall off?

    Often when I turn on my IBM T43 laptop, I get a bubble that says that Windows Firewall is turned off.  I click on the bubble, and then follow the steps to turn on the firewall. I am running Trend Micro Titanium Internet Security 2012 version 5.2.1035

  • I had the virus "XP Antivirus 2012" and now impossible to update MSE

    I had the virus "XP Antivirus 2012" and now impossible to update MSE.  Yesterday, I downloaded the Scanner of MS on another computer and transferred to the computer infected in safe mode and ran the Scanner from Ms.  Fortunately, it removed the virus

  • Save user data in an XML file

    Hello In my application, I want the user to be able to generate content (in a TextField or TextArea), then save it somehow and be able to view the next time it opens the application. I know how to display data that is stored in an XML file and I know

  • replaceing harddrive and reinstalling windows7

    I have a Dell Inspiron 15r n5010 core i3 m380 running Windows 7 and hard drive needs replacing. I can do it physically, but how can I move Windows 7 and and all its features of origin to the new hard drive. I saved all my personal info on a removable