Site to Site VPN ASA 5510
OK my forehead is painful to all keyboard strokes that I know that it must be something simple, but I am brand new to the SAA. I had a site to site VPN configuration via routers 1751 that worked very well, but we're looking to add some more remote field offices, and I felt that it would be easier to maintain several sites is on the ASA 5510. I have the VPN configured on the SAA and he said that the tunnel is up. I can telnet to the ASA and ping the remote gateway on the even side of VPN and it pings fine. If I try to ping on a local computer, I get a "Request timed out". If I makes no changes apart from go to the computer room and replace the network cable the 1751 and then through the 1751 I can now ping the remote door way to my computer. The remote router works obviously very well, my statement of route on my router for vpn push through the ASA (same ip address) IP traffic that has been used by the 1751 works obviously. It seems so just like ASA is not being pushed in the ethernet0/0 VPN traffic or at least it is not encrypted. I also noticed that the ACL for NAT seems to increase in number of access either it seems, there is really just one small thing missing to make the ASA except and encrypt incoming traffic on ethernet0/0:
My network is not configured with a DMZ is something like that, the ASA ethernet0/0 and my local network on the same subnet:
Router (Cisco 2811)
|
Layer switch 2 (ProCurve)
| |
ASA5510 LAN computers
I'm trying to except both sides of the VPN in and out on Ethernet0/0 traffic I saw there was a framework for this "permit communication between VPN peers connected to the same interface' and I've activated this option.
In short, I need to understand why the VPN tunnel shows that upward and I can ping the remote of the SAA, but peripheral gateway on my network can not ping to the remote gateway through the int Ethernet0/0 on the SAA.
From the console of the ASA, I get this:
ASA5510 # ping 192.52.128.1
Send 5, echoes ICMP 100 bytes to 192.52.128.1, wait time is 2 seconds:
!!!!!
Success rate is 100 per cent (5/5), round-trip min/avg/max = 100/108/120 ms
ASA5510 # show crypto ipsec his
Interface: *.
Tag crypto map: * _map, local addr: 10.52.120.23
local ident (addr, mask, prot, port): (10.52.120.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.52.128.0/255.255.255.0/0/0)
current_peer: x.x.x.204
program #pkts: 9, #pkts encrypt: 9, #pkts digest: 9
decaps #pkts: 9, #pkts decrypt: 9, #pkts check: 9
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 9, #pkts comp failed: 0, #pkts Dang failed: 0
#send errors: 0, #recv errors: 0
local crypto endpt. : 10.52.120.23, remote Start crypto. : x.x.x.204
Path mtu 1500, fresh ipsec generals 60, media, mtu 1500
current outbound SPI: C49EF75F
SAS of the esp on arrival:
SPI: 0x21FDBB9D (570276765)
transform: esp-3des esp-md5-hmac
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 1, crypto-map: * _map
calendar of his: service life remaining (KB/s) key: (3824999/3529)
Size IV: 8 bytes
support for replay detection: Y
outgoing esp sas:
SPI: 0xC49EF75F (3298752351)
transform: esp-3des esp-md5-hmac
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 1, crypto-map: * _map
calendar of his: service life remaining (KB/s) key: (3824999/3527)
Size IV: 8 bytes
support for replay detection: Y
From my office on the 10.52.120.0 even the etherenet0/0 interface on the ASA network I get this:
C:\Users\***>ping 192.52.128.1
Ping 192.52.128.1 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Ping statistics for 192.52.128.1:
Packets: Sent = 4, received = 0, lost = 4 (100% loss)
C:\Users\***>ping 10.52.120.23
Ping 10.52.120.23 with 32 bytes of data:
Reply from 10.52.120.23: bytes = 32 time = 5ms TTL = 255
Reply from 10.52.120.23: bytes = 32 time = 3ms TTL = 255
Reply from 10.52.120.23: bytes = 32 time = 1ms TTL = 255
Reply from 10.52.120.23: bytes = 32 time = 1ms TTL = 255
Ping statistics for 10.52.120.23:
Packets: Sent = 4, received = 4, lost = 0 (0% loss),
Time approximate round trip in milli-seconds:
Minimum = 1ms, Maximum = 5ms, average = 2ms
Count on VPN Tunnel ACL does not increase when I try to ping the address of the remote gateway.
Here is the running of the ASA configuration:
ASA Version 7.0 (2)
names of
!
interface Ethernet0/0
nameif InsideNetwork
security-level 100
IP 10.52.120.23 255.255.255.0
!
interface Ethernet0/1
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
management only
!
activate the encrypted password of XXXXXXXXXXXXXXXX
passwd encrypted XXXXXXXXXXXXXXXXXXX
ciscoasa hostname
domain default.domain.invalid
passive FTP mode
permit same-security-traffic intra-interface
Access extensive list ip 10.52.120.0 InsideNetwork_nat0_outbound allow 255.255.25
5.0 192.52.128.0 255.255.255.0
Access extensive list ip 10.52.120.0 InsideNetwork_cryptomap_20 allow 255.255.255
.0 192.52.128.0 255.255.255.0
pager lines 24
asdm of logging of information
management of MTU 1500
MTU 1500 InsideNetwork
management of the interface of the monitor
the interface of the monitor InsideNetwork
ASDM image disk0: / asdm - 502.bin
don't allow no asdm history
ARP timeout 14400
NAT (InsideNetwork) 0-list of access InsideNetwork_nat0_outbound
Route InsideNetwork 0.0.0.0 0.0.0.0 10.52.120.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00
Timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
Enable http server
http 192.168.1.0 255.255.255.0 management
http 10.52.120.0 255.255.255.0 InsideNetwork
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
card crypto InsideNetwork_map 20 corresponds to the address InsideNetwork_cryptomap_20
card crypto InsideNetwork_map 20 set peer x.x.x.204
InsideNetwork_map 20 transform-set ESP-3DES-MD5 crypto card game
InsideNetwork_map InsideNetwork crypto map interface
ISAKMP enable InsideNetwork
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 3des encryption
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
Telnet 10.52.120.0 255.255.255.0 InsideNetwork
Telnet timeout 5
SSH timeout 5
Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
dhcpd lease 3600
dhcpd ping_timeout 50
enable dhcpd management
tunnel-group x.x.x.204 type ipsec-l2l
x.x.x.204 group of tunnel ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
Policy-map global_policy
class inspection_default
inspect the dns-length maximum 512
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
Cryptochecksum:7e478b60b3e406091de466675c52eaaa
: end
I haven't added anything to the config except what seemed necessary to get the job of VPN tunnel. It should be fairly clean.
Thanks in advance for any help... I really hope that it is something really simple as a recruit ASA just forgot
Strange, but good news. Thanks for the update. I'm glad everything is working.
THX
MS
Tags: Cisco Security
Similar Questions
-
Site to Site VPN - ASA 5510 / 851 router - no Sas?
We have installed an ASA 5510, version 1.0000 software running. In a remote area, we have a Cisco router to 851 with tunneling IPSec VPN for a PIX 515e. I try to open a backup between the 851 and ASA connection new, and I have a problem. I used ASDM on the side of the ASA and CCP on the side 851 and created a new VPN site to site on both, with PSK encryption algorithms, etc.. I checked the connectivity between the external interfaces of the two devices, and the associated ACLs are simple, because they allow all IP traffic on the internal side of the two devices to talk with each other.
When I do a "crypto isakmp to show his" on the SAA, I get "there is no its isakmp. When I do the same on the 851 router, I see only the existing connection to the PIX. It seems that the tunnel does not run again. I turned on debug various crypto and sent a series of pings, and I don't see any tunnel initiaion even be attempted.
CCP has a VPN to test the tool built in to the router. ASDM has a similar feature? Here's the relevant configs (at least I think... the SAA is enough Greek to me):
ASA 5510 (within the network of 10.20.0.0/16. The perfectly functional PIX is also on this network, with a different public IP address)
access-list ATTOutside_2_cryptomap extended permit ip object-group DM_INLINE_NETWORK_1 10.192.0.0 255.255.0.0 !
nat (Inside,ATTOutside) source static NETWORK_OBJ_10.20.0.0_16 NETWORK_OBJ_10.20.0.0_16 destination static NETWORK_OBJ_10.192.0.0_16 NETWORK_OBJ_10.192.0.0_16
!crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map ATTOutside_map 2 match address ATTOutside_2_cryptomap crypto map ATTOutside_map 2 set peer 24.140.152.144 crypto map ATTOutside_map 2 set transform-set ESP-3DES-MD5 crypto map ATTOutside_map interface ATTOutside
!crypto isakmp enable ATTOutside crypto isakmp enable Inside crypto isakmp policy 10 authentication crack encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 20 authentication rsa-sig encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 30 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 40 authentication crack encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 50 authentication rsa-sig encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 60 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 70 authentication crack encryption aes hash sha group 2 lifetime 86400 crypto isakmp policy 80 authentication rsa-sig encryption aes hash sha group 2 lifetime 86400 crypto isakmp policy 90 authentication pre-share encryption aes hash sha group 2 lifetime 86400 crypto isakmp policy 100 authentication crack encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 110 authentication rsa-sig encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 120 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 130 authentication crack encryption des hash sha group 2 lifetime 86400 crypto isakmp policy 140 authentication rsa-sig encryption des hash sha group 2 lifetime 86400 crypto isakmp policy 150 authentication pre-share encryption des hash sha group 2 lifetime 86400 crypto isakmp policy 170 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400
!tunnel-group 24.140.152.144 type ipsec-l2l tunnel-group 24.140.152.144 ipsec-attributes
!
851 router (within the 10.192.4.0/24 network)
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
!
crypto isakmp policy 2
encr 3des
authentication pre-share
group 2
!
crypto isakmp policy 3
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key si9bw1u8woaz address 65.42.15.142
crypto isakmp key 123 address 12.49.251.3
!
!
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA2 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP_3DES_MD5 esp-3des esp-md5-hmac
!
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to65.42.15.142
set peer 65.42.15.142
set transform-set ESP-3DES-SHA1
match address 102
crypto map SDM_CMAP_1 2 ipsec-isakmp
description Tunnel to12.49.251.3
set peer 12.49.251.3
set transform-set ESP_3DES_MD5
match address 102
!
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.20.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.1.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.10.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.11.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.12.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.13.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.14.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.18.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.19.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.22.0.0 0.0.255.255
access-list 102 permit ip 10.192.4.0 0.0.0.255 10.23.0.0 0.0.255.255
Michael,
Since you are using the same ACL, subnets, even and even while on your router to your VPN 1 tunnels config and 2, your second VPN tunnel will not succeed because the router already has a tunnel with the PIX for the same traffic.
If you want to configure the ASA as peer backup scratch the second card encryption and instead, add the public IP ASA as a second peer under the original crypto configuration.
Like this:
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to65.42.15.142
set peer 65.42.15.142
game of transformation-ESP-3DES-SHA1set peer 12.49.251.3
match address 102
The router will attempt to connect to the PIX and if this fails (which means that the PIX has never responded) then it will try to connect to the ASA.
To test it, you could do either of two things: 1. taking the internet conection low PIX will make the router try to connect to the secondary host. 2: change (temporarily) on the router address peer of the PIX to a bogus IP that won't respond, when only one omits the router must try to negotiate with the ASA.
I hope this helps.
Raga
-
I set up a site to Site VPN using ASA 5505, but when I submit the order
"sh crypto ipsec his ' it says 'there are no ipsec security associations.
I have attached the configurations.
Hello
I saw you nat nat of entry (inside) 2-list of access limenat, would you change to, nat (inside) 0-list of access limenat. See which make all the difference.
Do you want to take a capture of packets when the remote IP address ping?
course list (Local subnet) host (remote subnet) host allowed access
Cap list of allowed access host host (remote subnet) (Local subnet)
Course access-list in hidden inside
Show Cap Hat
Now you can see the list of access capture
Debug crypto isakmp 200
Debug crypto ipsec 200
-
NAT IPSEC site to site VPN ASA 8.4
My goal is to create a VPN to me (61.227.106.64) to a seller (9.105.8.204) using an ASA 5510 with 8.4 on it. Local private networks of the seller is 10.134.115.0/24 and 10.135.115.0/24. My private LAN is 10.11.102.0/24 but I want NAT it to 61.227.106.70.
The following configuration is correct?
ASA Version 8.4 (2)
interface Ethernet0/0
nameif LAN
security-level 0
IP 10.241.1.61 255.255.255.0
!
interface Ethernet0/1
nameif WAN
security-level 0
IP 61.227.106.64 255.255.255.0
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the CareOneTSFarm object
10.11.102.0 subnet 255.255.255.0
network of the Core_NAT object
Home 61.227.106.70
network of the NAT_to_outside object
subnet 0.0.0.0 0.0.0.0
the Core_LAN object-group network
object-network 10.134.115.0 255.255.255.0
object-network 10.135.115.0 255.255.255.0
VPNCore list extended access permitted ip object CareOneTSFarm object-group Core_LAN
public static CareOneTSFarm Core_NAT destination NAT (LAN, WAN) static source Core_LAN Core_LAN
!
network of the NAT_to_outside object
dynamic interface of NAT (LAN, WAN)
Route WAN 0.0.0.0 0.0.0.0 61.227.106.1 1
Route LAN 10.11.0.0 255.255.0.0 10.241.1.1 1
Crypto ipsec transform-set esp-aes-256 AES256_SHA, esp-sha-hmac ikev1
3600 seconds, duration of life crypto ipsec security association
card crypto VPN 50 corresponds to the address VPNCore
card crypto VPN 50 set peer 9.105.8.204
card crypto VPN 50 set transform-set AES256_SHA ikev1
IKEv1 crypto policy 10
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
card crypto VPN WAN interface
tunnel-group 9.105.8.204 type ipsec-l2l
IPSec-attributes tunnel-Group 9.105.8.204
IKEv1 pre-shared-key *.
This NAT line:
public static CareOneTSFarm Core_NAT destination NAT (LAN, WAN) static source Core_LAN Core_LAN
must be:
destination NAT (LAN, WAN) CareOneTSFarm Core_NAT Core_LAN Core_LAN static dynamic source
And the ACL VPNCore must correspond to the NATed IP instead of the real IP:
VPNCore list extended access permitted ip object Core_NAT object-group Core_LAN
-
S2S VPN Asa 5510 to 5505 no traffic passing (hair Pulling)
I have one site to another configured between a 5505 and ASA 5510, the tunnel is in place but can not pass any traffic one way or another. A 5510, 8.4.3 while the 5505 was 8.2. I find the version 8.2 the less confusing when configure the VPN. The new NAT throws me for a loop on the 5510. I have 1 tunnel upward and will already and it works fine. But when I do a new online, it won't pass any traffic.
The traffic I'm EFS is 5510 (192.168.180.0/24, 172.25.11.0/24)<-------> 5505 (192.168.197.0/24) many thanks in advance!
Here's the configs for the two.
main site of 5510
ASA Version 8.4(3) ! hostname ASA5510 domain-name fphc.us enable password dmbm8Lq9pBST.0kk encrypted passwd dmbm8Lq9pBST.0kk encrypted names ! interface Ethernet0/0 nameif Outside security-level 0 ip address x.x.x.130 255.255.255.240 ! interface Ethernet0/1 nameif Inside security-level 100 ip address 192.168.180.253 255.255.254.0 ! interface Ethernet0/2 speed 100 duplex full shutdown no nameif no security-level no ip address ! interface Ethernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 nameif management security-level 100 no ip address management-only ! boot system disk0:/asa843-k8.bin ftp mode passive clock timezone CST -6 clock summer-time CDT recurring dns domain-lookup Inside dns server-group DefaultDNS name-server 192.168.180.231 name-server 192.168.180.232 name-server 192.168.180.233 domain-name fphc.us same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj-192.168.180.0 subnet 192.168.180.0 255.255.254.0 object network obj-192.168.188.0 subnet 192.168.188.0 255.255.255.0 object network obj-216.86.7.128 subnet x.x.x.128 255.255.255.240 object network Mobile_Unit subnet 192.168.193.0 255.255.255.0 object network obj-172.27.0.0 subnet 172.27.0.0 255.255.255.0 object network obj_any subnet 0.0.0.0 0.0.0.0 object network obj-172.25.11.0 subnet 172.25.11.0 255.255.255.0 object network obj-172.35.0.0 subnet 172.35.0.0 255.255.254.0 object network SpamBox_1 host 192.168.180.244 object network SpamBox_2 host 192.168.180.248 object network Exchange host 192.168.180.235 object network PMG subnet 192.168.178.0 255.255.255.0 object network Outside_Gateway host x.x.x.129 object network AHCCN subnet 172.35.0.0 255.255.254.0 object network MM subnet 10.90.254.0 255.255.255.0 object network NETWORK_OBJ_172.27.0.0_25 subnet 172.27.0.0 255.255.255.128 object network NETWORK_OBJ_172.27.0.0_26 subnet 172.27.0.0 255.255.255.192 object network obj-172.35.1.199 host 172.35.1.199 object network obj-192.168.51.5 host 192.168.51.5 object service 6004 service udp destination eq 6004 object network AT_Remote subnet 192.168.197.0 255.255.255.0 object-group service DM_INLINE_SERVICE_2 service-object icmp echo service-object icmp echo-reply service-object tcp-udp destination eq domain service-object tcp-udp destination eq www object-group network DM_INLINE_NETWORK_1 network-object object obj-172.25.11.0 network-object object obj-172.35.0.0 network-object object obj-192.168.180.0 object-group network DM_INLINE_NETWORK_2 network-object object AHCCN network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 object-group network DM_INLINE_NETWORK_3 network-object object AHCCN network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 object-group network DM_INLINE_NETWORK_16 network-object object MM network-object object obj-172.25.11.0 network-object object obj-172.35.0.0 network-object object obj-192.168.180.0 object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group icmp-type DM_INLINE_ICMP_1 icmp-object echo icmp-object source-quench object-group network DM_INLINE_NETWORK_5 network-object object AHCCN network-object object MM network-object object obj-172.25.11.0 network-object object obj-172.35.0.0 network-object object obj-192.168.180.0 object-group network DM_INLINE_NETWORK_6 network-object object obj-172.25.11.0 network-object object obj-172.35.0.0 network-object object obj-192.168.180.0 object-group service DM_INLINE_SERVICE_4 service-object icmp service-object icmp echo service-object icmp echo-reply object-group service DM_INLINE_SERVICE_5 service-object tcp-udp destination eq domain service-object tcp destination eq smtp service-object tcp destination eq ssh service-object icmp echo service-object icmp echo-reply service-object udp destination eq ntp service-object udp destination eq time object-group service DM_INLINE_SERVICE_6 service-object tcp-udp destination eq domain service-object tcp destination eq smtp service-object tcp destination eq ssh service-object icmp echo service-object icmp echo-reply service-object udp destination eq ntp service-object udp destination eq time object-group service DM_INLINE_SERVICE_0 service-object icmp echo service-object icmp echo-reply service-object tcp destination eq www service-object tcp destination eq https service-object tcp destination eq smtp service-object tcp-udp destination eq domain service-object object 6004 object-group network DM_INLINE_NETWORK_7 network-object object MM network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 network-object object obj-172.35.0.0 object-group network DM_INLINE_NETWORK_8 network-object 172.25.11.0 255.255.255.0 network-object 172.35.0.0 255.255.254.0 object-group service DM_INLINE_SERVICE_7 service-object tcp-udp destination eq domain service-object object 6004 service-object icmp echo service-object icmp echo-reply service-object tcp destination eq www service-object tcp destination eq https service-object tcp destination eq smtp object-group network DM_INLINE_NETWORK_10 network-object 172.25.11.0 255.255.255.0 network-object 172.35.0.0 255.255.254.0 object-group network DM_INLINE_NETWORK_9 network-object object obj-172.25.11.0 network-object object obj-172.35.0.0 object-group network DM_INLINE_NETWORK_11 network-object object AHCCN network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 object-group service DM_INLINE_SERVICE_1 service-object tcp-udp destination eq domain service-object tcp destination eq smtp service-object udp destination eq ntp object-group network DM_INLINE_NETWORK_13 network-object object AHCCN network-object object obj-172.25.11.0 object-group network DM_INLINE_NETWORK_14 network-object object AHCCN network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 object-group network DM_INLINE_NETWORK_12 network-object object AHCCN network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 object-group service DM_INLINE_SERVICE_3 service-object tcp-udp destination eq domain service-object tcp destination eq smtp service-object udp destination eq ntp object-group service DM_INLINE_SERVICE_8 service-object tcp-udp destination eq domain service-object tcp destination eq smtp service-object udp destination eq ntp object-group service Exchange-6001 udp port-object range 6001 6004 object-group network DM_INLINE_NETWORK_15 network-object object AHCCN network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 object-group service DM_INLINE_SERVICE_10 service-object ip service-object icmp echo service-object icmp echo-reply object-group service DM_INLINE_SERVICE_9 service-object ip service-object icmp echo service-object icmp echo-reply service-object tcp-udp destination eq domain service-object tcp destination eq citrix-ica service-object tcp destination eq www service-object tcp destination eq https object-group network DM_INLINE_NETWORK_18 network-object object AHCCN network-object object obj-172.25.11.0 object-group network DM_INLINE_NETWORK_19 network-object object obj-172.25.11.0 network-object object obj-172.35.0.0 network-object object obj-192.168.180.0 object-group network DM_INLINE_NETWORK_20 network-object object AHCCN network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 object-group network DM_INLINE_NETWORK_17 network-object object AHCCN network-object object obj-172.25.11.0 network-object object obj-192.168.180.0 access-list Inside_nat0_outbound extended permit ip object-group DM_INLINE_NETWORK_10 object PMG access-list Inside_nat0_outbound extended permit ip object-group DM_INLINE_NETWORK_1 192.168.188.0 255.255.255.0 access-list Inside_nat0_outbound extended permit ip object-group DM_INLINE_NETWORK_7 object obj-172.27.0.0 access-list Outside_1_cryptomap extended permit ip 192.168.188.0 255.255.255.0 object-group DM_INLINE_NETWORK_14 access-list Outside_access_in extended permit object-group DM_INLINE_SERVICE_9 object AT_Remote object-group DM_INLINE_NETWORK_15 access-list Outside_access_in extended permit object-group DM_INLINE_SERVICE_4 any any access-list Outside_access_in extended permit ip object Mobile_Unit object-group DM_INLINE_NETWORK_12 log debugging access-list Outside_access_in extended permit object-group DM_INLINE_SERVICE_7 object PMG object-group DM_INLINE_NETWORK_8 access-list Outside_access_in extended permit object-group DM_INLINE_SERVICE_0 any object Exchange access-list Outside_access_in extended permit object-group DM_INLINE_SERVICE_5 any object SpamBox_1 access-list Outside_access_in extended permit object-group DM_INLINE_SERVICE_6 any object SpamBox_2 access-list Outside_access_in extended permit ip 192.168.188.0 255.255.255.0 object-group DM_INLINE_NETWORK_2 access-list Outside_access_in extended deny ip 127.0.0.0 255.255.255.0 any log access-list Outside_access_in extended deny ip 10.0.0.0 255.255.255.0 any log access-list Outside_access_in extended deny ip 169.254.0.0 255.255.0.0 any log access-list Outside_access_in extended deny ip 224.0.0.0 255.0.0.0 any log access-list Outside_access_in extended deny ip 239.0.0.0 255.0.0.0 any log access-list Outside_access_in extended deny ip 173.0.0.0 255.0.0.0 any log debugging access-list Outside_access_in extended deny ip 224.0.0.0 255.255.255.31 any access-list Outside_access_in extended deny ip 192.168.0.0 255.255.0.0 any access-list Outside_access_in extended deny ip any any access-list global_mpc extended permit ip any any access-list global_access extended permit udp object obj-172.35.1.199 any eq snmp log disable access-list global_access extended permit ip object obj-172.27.0.0 any access-list splitTunnelAcl standard permit 192.168.180.0 255.255.254.0 access-list splitTunnelAcl standard permit 172.35.0.0 255.255.254.0 access-list splitTunnelAcl standard permit 172.25.11.0 255.255.255.0 access-list splitTunnelAcl standard permit 10.90.254.0 255.255.255.0 access-list Outside_cryptomap_1 extended permit ip object PMG object-group DM_INLINE_NETWORK_13 access-list Inside_access_in extended permit ip object obj_any any access-list Inside_access_in extended permit icmp any any object-group DM_INLINE_ICMP_1 log disable access-list Inside_access_in extended permit object-group DM_INLINE_SERVICE_8 object Exchange any log access-list Inside_access_in extended permit object-group DM_INLINE_SERVICE_1 object SpamBox_1 any log access-list Inside_access_in extended permit object-group DM_INLINE_SERVICE_3 object SpamBox_2 any log access-list Inside_access_in extended deny ip any any access-list Outside_cryptomap_2 extended permit ip object-group DM_INLINE_NETWORK_17 object AT_Remote access-list Outside_cryptomap extended permit ip object-group DM_INLINE_NETWORK_18 object PMG log access-list Outside_cryptomap_4 extended permit ip object-group DM_INLINE_NETWORK_3 object Mobile_Unit pager lines 24 logging enable logging timestamp logging emblem logging rate-limit unlimited level 1 logging rate-limit unlimited level 6 logging rate-limit unlimited level 7 mtu Outside 1500 mtu Inside 1500 mtu management 1500 ip local pool Client_Pool 172.27.0.50-172.27.0.100 mask 255.255.255.0 ip local pool RA_POOL 172.27.0.1-172.27.0.49 mask 255.255.255.0 ip verify reverse-path interface Outside ip verify reverse-path interface Inside no failover icmp unreachable rate-limit 1 burst-size 1 icmp permit any Outside icmp permit any Inside asdm history enable arp timeout 14400 nat (Inside,Outside) source static DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_9 destination static PMG PMG no-proxy-arp route-lookup nat (Inside,Outside) source static DM_INLINE_NETWORK_20 DM_INLINE_NETWORK_20 destination static AT_Remote AT_Remote no-proxy-arp route-lookup nat (Inside,Outside) source static DM_INLINE_NETWORK_5 DM_INLINE_NETWORK_5 destination static NETWORK_OBJ_172.27.0.0_25 NETWORK_OBJ_172.27.0.0_25 no-proxy-arp route-lookup nat (Inside,Outside) source static DM_INLINE_NETWORK_16 DM_INLINE_NETWORK_16 destination static NETWORK_OBJ_172.27.0.0_26 NETWORK_OBJ_172.27.0.0_26 no-proxy-arp route-lookup nat (Inside,Outside) source static DM_INLINE_NETWORK_1 DM_INLINE_NETWORK_1 destination static obj-192.168.188.0 obj-192.168.188.0 no-proxy-arp nat (Inside,Outside) source static DM_INLINE_NETWORK_19 DM_INLINE_NETWORK_19 destination static Mobile_Unit Mobile_Unit no-proxy-arp route-lookup nat (Inside,Outside) source static DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_11 destination static AT_Remote AT_Remote no-proxy-arp route-lookup ! object network obj_any nat (Inside,Outside) dynamic interface object network SpamBox_1 nat (Inside,Outside) static x.x.x.132 object network SpamBox_2 nat (Inside,Outside) static x.x.x.133 object network Exchange nat (Inside,Outside) static x.x.x.131 dns access-group Outside_access_in in interface Outside access-group Inside_access_in in interface Inside access-group global_access global route Outside 0.0.0.0 0.0.0.0 x.x.x..129 1 route Inside 10.90.254.0 255.255.255.0 192.168.180.1 1 route Inside 172.16.200.0 255.255.255.0 192.168.180.200 1 route Inside 172.25.10.0 255.255.255.0 192.168.180.200 1 route Inside 172.25.11.0 255.255.255.0 192.168.180.200 1 route Inside 172.25.12.0 255.255.255.0 192.168.180.200 1 route Inside 172.27.0.0 255.255.255.0 192.168.180.200 1 route Inside 172.29.0.0 255.255.0.0 192.168.180.200 1 route Inside 172.35.0.0 255.255.254.0 192.168.180.200 1 route Inside 192.168.182.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.183.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.184.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.185.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.186.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.187.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.189.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.190.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.191.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.192.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.194.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.195.0 255.255.255.0 192.168.180.200 1 route Inside 192.168.196.0 255.255.255.0 192.168.180.200 1 timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa-server DC's protocol radius max-failed-attempts 5 aaa-server DC's (Inside) host 192.168.180.231 timeout 5 key ***** user-identity default-domain LOCAL http server enable http 192.168.180.0 255.255.255.0 Inside http 0.0.0.0 0.0.0.0 Inside http 172.27.0.0 255.255.255.0 Outside http 172.27.0.0 255.255.255.0 Inside snmp-server group Authentication&Encryption v3 priv snmp-server user trap Authentication&Encryption v3 encrypted auth md5 87:1d:3a:bd:50:49:7d:dc:45:89:a0:dc:c9:66:ed:78 priv 3des 87:1d:3a:bd:50:49:7d:dc:45:89:a0:dc:c9:66:ed:78:08:c6:ef:b2:7e:89:45:f2:6f:78:b5:01:33:47:68:c9 snmp-server host Inside 172.35.1.199 community ***** version 2c snmp-server host Inside 192.168.180.7 community ***** version 2c snmp-server location MLK snmp-server contact xxxxxxxx snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart snmp-server enable traps syslog snmp-server enable traps ipsec start stop snmp-server enable traps entity config-change fru-insert fru-remove snmp-server enable traps remote-access session-threshold-exceeded snmp-server enable traps cpu threshold rising snmp-server enable traps ikev2 start no sysopt connection reclassify-vpn sysopt connection preserve-vpn-flows crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association lifetime seconds 43200 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map Outside_map 1 match address Outside_1_cryptomap crypto map Outside_map 1 set peer 173.10.204.46 crypto map Outside_map 1 set ikev1 phase1-mode aggressive crypto map Outside_map 1 set ikev1 transform-set ESP-3DES-SHA crypto map Outside_map 1 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256 crypto map Outside_map 1 set ikev2 pre-shared-key ***** crypto map Outside_map 1 set security-association lifetime seconds 460800 crypto map Outside_map 4 match address Outside_cryptomap_1 crypto map Outside_map 4 set peer 207.190.237.254 crypto map Outside_map 4 set ikev1 phase1-mode aggressive group5 crypto map Outside_map 4 set ikev1 transform-set ESP-AES-128-SHA crypto map Outside_map 4 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256 crypto map Outside_map 4 set security-association lifetime seconds 460800 crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map 1 match address Outside_cryptomap_2 crypto map outside_map 1 set peer x.x.x.201 crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 2 match address Outside_cryptomap crypto map outside_map 2 set peer x.x.x.254 crypto map outside_map 2 set ikev1 phase1-mode aggressive group5 crypto map outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 2 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256 crypto map outside_map 3 match address Outside_cryptomap_4 crypto map outside_map 3 set peer x.x.216.130 crypto map outside_map 3 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface Outside crypto ca trustpoint LOCAL-CA-SERVER keypair LOCAL-CA-SERVER crl configure crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=FPHC-ASA serial-number keypair LOCAL-CA-SERVER crl configure crypto ca server shutdown crypto ca certificate chain LOCAL-CA-SERVER certificate ca 01 308201ff 30820168 a0030201 02020101 300d0609 2a864886 f70d0101 05050030 13311130 0f060355 04031308 46504843 2d415341 301e170d 31323039 32303232 34393034 5a170d31 35303932 30323234 3930345a 30133111 300f0603 55040313 08465048 432d4153 4130819f 300d0609 2a864886 f70d0101 01050003 818d0030 81890281 8100e841 eeca425c 20c47a19 3b335924 30281111 cff571d7 0bb63dd8 5f3194f5 59d99cb1 60269694 aa13c591 505e0575 2de5ebb1 92d7c931 807f807b 6e84ee54 1da4ccaf 1f109f53 94c6e567 a8064e27 e27f3ea0 94f7bf32 2fe6064c c2bbcd0d 7b0f8806 8614fcf9 80c6e4e1 83da75c5 080c7117 09e1d574 f17de8ac 1da4f2f9 f6e10203 010001a3 63306130 0f060355 1d130101 ff040530 030101ff 300e0603 551d0f01 01ff0404 03020186 301f0603 551d2304 18301680 144cb3da 6b6a5a14 c4b78674 49609b6b 8e58ea5f a3301d06 03551d0e 04160414 4cb3da6b 6a5a14c4 b7867449 609b6b8e 58ea5fa3 300d0609 2a864886 f70d0101 05050003 818100e0 7c9e15c3 13068614 788ff4d3 f282a4f4 fde72b00 3b05748f 0a4f68ec 6a7eb5fb 40c6d505 b1c35372 87102173 bb017e4b 2697c8f5 b66395f2 1418c77c 3e959343 84674b96 33558a08 629336c8 39c742bf 6b727b00 388a7102 8619cb5a e4227aaf b58e267c 9e8b23d6 94cdc789 eb29cd96 1e579770 a2aa58ab 40694bb9 12888d quit crypto ca certificate chain ASDM_TrustPoint0 certificate bd555b50 308201f7 30820160 a0030201 020204bd 555b5030 0d06092a 864886f7 0d010105 05003040 3111300f 06035504 03130846 5048432d 41534131 2b301206 03550405 130b4a4d 58313632 33583130 51301506 092a8648 86f70d01 09021608 46504843 2d415341 301e170d 31323039 32303232 35383434 5a170d32 32303931 38323235 3834345a 30403111 300f0603 55040313 08465048 432d4153 41312b30 12060355 0405130b 4a4d5831 36323358 31305130 1506092a 864886f7 0d010902 16084650 48432d41 53413081 9f300d06 092a8648 86f70d01 01010500 03818d00 30818902 818100e8 41eeca42 5c20c47a 193b3359 24302811 11cff571 d70bb63d d85f3194 f559d99c b1602696 94aa13c5 91505e05 752de5eb b192d7c9 31807f80 7b6e84ee 541da4cc af1f109f 5394c6e5 67a8064e 27e27f3e a094f7bf 322fe606 4cc2bbcd 0d7b0f88 068614fc f980c6e4 e183da75 c5080c71 1709e1d5 74f17de8 ac1da4f2 f9f6e102 03010001 300d0609 2a864886 f70d0101 05050003 8181008b c7a3e119 f1c6f60c 56ab7fd4 5096cfdf abb44331 fe3a0249 7f5fe79b 38a044c2 9a8b907d 12feba5d 6298a414 c4973369 040585b8 26b8b29e dfe7e226 0b10d08e 03658648 2fb0233e 27204339 c5a1c270 a0fec5b4 834340ac 9afefe75 4f802cb6 fb21b89c 9016e32c 2e772c00 191d23e0 036c4321 93a43b48 a6b682af 5dd5c0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable Outside crypto ikev1 enable Outside crypto ikev1 enable management crypto ikev1 policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 192.168.180.0 255.255.255.0 Inside telnet 172.27.0.0 255.255.255.0 Inside telnet timeout 10 ssh 192.168.180.0 255.255.255.0 Inside ssh 172.27.0.0 255.255.255.0 Inside ssh timeout 20 console timeout 0 management-access Inside vpn load-balancing interface lbpublic Outside interface lbprivate Inside threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp authenticate ntp server 50.77.217.185 source Outside prefer ntp server 216.171.120.36 source Outside webvpn group-policy "S2S-RA-Group Policy" internal group-policy "S2S-RA-Group Policy" attributes vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client group-policy DfltGrpPolicy attributes vpn-filter value Inside_nat0_outbound vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec ssl-client ssl-clientless group-policy GroupPolicy_x.x.x.46 internal group-policy GroupPolicy_x.x.x.46 attributes vpn-filter value Outside_1_cryptomap vpn-tunnel-protocol ikev1 ikev2 group-policy GroupPolicy_x.x.x.254 internal group-policy GroupPolicy_x.x.x.254 attributes vpn-filter value Outside_cryptomap_1 vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec group-policy GroupPolicy_x.x.x.201 internal group-policy GroupPolicy_x.x.x.201 attributes vpn-filter value Outside_cryptomap_2 vpn-tunnel-protocol ikev1 group-policy GroupPolicy_x.x.216.130 internal group-policy GroupPolicy_x.x.216.130 attributes vpn-tunnel-protocol ikev1 group-policy VPN-GROUP2 internal group-policy VPN-GROUP2 attributes dns-server value 192.168.180.231 192.168.180.232 vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value splitTunnelAcl default-domain value fphc.us group-policy VPN-GROUP internal group-policy VPN-GROUP attributes dns-server value 192.168.180.231 192.168.180.232 vpn-filter value splitTunnelAcl vpn-tunnel-protocol ikev1 l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value splitTunnelAcl default-domain value fphc.us username mark password YTp0IwzeNwb5kS8J encrypted privilege 15 tunnel-group DefaultRAGroup general-attributes default-group-policy VPN-GROUP tunnel-group x.x.x.46 type ipsec-l2l tunnel-group x.x.x.46 general-attributes default-group-policy GroupPolicy_x.x.x.46 tunnel-group x.x.x.46 ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** tunnel-group x.x.x.201 type ipsec-l2l tunnel-group x.x.x.201 general-attributes default-group-policy GroupPolicy_x.x.x.201 tunnel-group x.x.x.201 ipsec-attributes ikev1 pre-shared-key ***** tunnel-group VPN-GROUP type remote-access tunnel-group VPN-GROUP general-attributes address-pool Client_Pool authentication-server-group DC's default-group-policy VPN-GROUP tunnel-group VPN-GROUP ipsec-attributes ikev1 pre-shared-key ***** tunnel-group x.x.x.254 type ipsec-l2l tunnel-group x.x.x.254 general-attributes default-group-policy GroupPolicy_x.x.x.254 tunnel-group x.x.x.254 ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** tunnel-group VPN-GROUP2 type remote-access tunnel-group VPN-GROUP2 general-attributes address-pool RA_POOL authentication-server-group DC's default-group-policy VPN-GROUP2 tunnel-group VPN-GROUP2 ipsec-attributes ikev1 pre-shared-key ***** tunnel-group x.x.x.130 type ipsec-l2l tunnel-group x.x.x.130 general-attributes default-group-policy GroupPolicy_x.x.x.130 tunnel-group x.x.x.130 ipsec-attributes ikev1 pre-shared-key ***** tunnel-group PMG type ipsec-l2l tunnel-group PMG general-attributes default-group-policy GroupPolicy_x.x.x.254 tunnel-group PMG ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** tunnel-group-map default-group DefaultL2LGroup ! class-map global-class match access-list global_mpc class-map inspection_default match default-inspection-traffic class-map http_https description http_https match access-list Outside_access_in ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options class global-class user-statistics accounting policy-map http_https class http_https set connection timeout idle 1:15:00 reset user-statistics accounting ! service-policy global_policy global service-policy http_https interface Outside smtp-server 192.168.180.235 prompt hostname context no call-home reporting anonymous Cryptochecksum:fcb4c2d9a982c11054c31ee4db778012 : end
5505 remote site
ASA Version 8.2(5) ! hostname AT-Remote domain-name fphc.us enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted names name 172.35.0.0 AHCCN name 172.25.11.0 AHCCN-1 name 192.168.180.0 FPHC ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 switchport trunk allowed vlan 1,30 switchport trunk native vlan 1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.197.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address x.x.x.201 255.255.255.252 ! ! boot system disk0:/asa825-k8.bin ftp mode passive dns domain-lookup inside dns domain-lookup outside dns server-group DefaultDNS name-server 68.87.68.162 name-server 68.87.74.162 domain-name fphc.us dns server-group DNS_Internal name-server 192.168.180.231 name-server 192.168.180.232 domain-name fphc.us same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network obj_any object-group network 172.25.11.0 object-group network 172.35.0.0 object-group network 192.168.180.0 object-group network ASA-FW object-group network Comcast_Outside object-group network AT_Local object-group network NETWORK_OBJ_192.168.197.0_24 object-group icmp-type DM_INLINE_ICMP_1 icmp-object echo icmp-object echo-reply object-group service DM_INLINE_SERVICE_3 service-object ip service-object icmp echo service-object icmp echo-reply object-group service DM_INLINE_SERVICE_2 service-object ip service-object icmp object-group network obj_remote object-group network Franklin_Remote network-object AHCCN-1 255.255.255.0 network-object AHCCN 255.255.254.0 network-object FPHC 255.255.254.0 access-list outside_access_in extended permit ip object-group Franklin_Remote 192.168.197.0 255.255.255.0 access-list outside_access_in extended permit icmp any any object-group DM_INLINE_ICMP_1 log debugging access-list inside_access_in extended permit ip any any log access-list inside_access_in extended permit icmp any any echo log access-list outside_1_cryptomap extended permit ip 192.168.197.0 255.255.255.0 object-group Franklin_Remote access-list inside_nat0_outbound extended permit ip 192.168.197.0 255.255.255.0 object-group Franklin_Remote access-list inside_nat_outbound extended permit ip any interface outside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside asdm image disk0:/asdm-645.bin no asdm history enable arp timeout 14400 global (outside) 101 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 101 access-list inside_nat_outbound access-group inside_access_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 x.x.x.202 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 0.0.0.0 0.0.0.0 inside http 192.168.197.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart sysopt connection preserve-vpn-flows sysopt noproxyarp inside sysopt noproxyarp dmz crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 43200 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set peer 216.86.7.130 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto ca trustpoint _SmartCallHome_ServerCA crl configure crypto ca certificate chain _SmartCallHome_ServerCA certificate ca 6ecc7aa5a7032009b8cebcf4e952d491 308205ec 308204d4 a0030201 0202106e cc7aa5a7 032009b8 cebcf4e9 52d49130 0d06092a 864886f7 0d010105 05003081 ca310b30 09060355 04061302 55533117 30150603 55040a13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b 13165665 72695369 676e2054 72757374 204e6574 776f726b 313a3038 06035504 0b133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72 20617574 686f7269 7a656420 75736520 6f6e6c79 31453043 06035504 03133c56 65726953 69676e20 436c6173 73203320 5075626c 69632050 72696d61 72792043 65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31 30303230 38303030 3030305a 170d3230 30323037 32333539 35395a30 81b5310b 30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20 496e632e 311f301d 06035504 0b131656 65726953 69676e20 54727573 74204e65 74776f72 6b313b30 39060355 040b1332 5465726d 73206f66 20757365 20617420 68747470 733a2f2f 7777772e 76657269 7369676e 2e636f6d 2f727061 20286329 3130312f 302d0603 55040313 26566572 69536967 6e20436c 61737320 33205365 63757265 20536572 76657220 4341202d 20473330 82012230 0d06092a 864886f7 0d010101 05000382 010f0030 82010a02 82010100 b187841f c20c45f5 bcab2597 a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10 9c688b2e 957b899b 13cae234 34c1f35b f3497b62 83488174 d188786c 0253f9bc 7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b 15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845 63cd1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced 4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f 81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 02030100 01a38201 df308201 db303406 082b0601 05050701 01042830 26302406 082b0601 05050730 01861868 7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1d130101 ff040830 060101ff 02010030 70060355 1d200469 30673065 060b6086 480186f8 45010717 03305630 2806082b 06010505 07020116 1c687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f6370 73302a06 082b0601 05050702 02301e1a 1c687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406 03551d1f 042d302b 3029a027 a0258623 68747470 3a2f2f63 726c2e76 65726973 69676e2e 636f6d2f 70636133 2d67352e 63726c30 0e060355 1d0f0101 ff040403 02010630 6d06082b 06010505 07010c04 61305fa1 5da05b30 59305730 55160969 6d616765 2f676966 3021301f 30070605 2b0e0302 1a04148f e5d31a86 ac8d8e6b c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973 69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30 1b311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301d0603 551d0e04 1604140d 445c1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 1d230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300d0609 2a864886 f70d0101 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e b2227055 d9203340 3307c265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a 6decd018 7d494aca 99c71928 a2bed877 24f78526 866d8705 404167d1 273aeddc 481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16 b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0 5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8 6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28 6c2527b9 deb78458 c61f381e a4c4cb66 quit crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 20 authentication rsa-sig encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 30 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 40 authentication crack encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 50 authentication rsa-sig encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 60 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 70 authentication crack encryption aes hash sha group 2 lifetime 86400 crypto isakmp policy 80 authentication rsa-sig encryption aes hash sha group 2 lifetime 86400 crypto isakmp policy 90 authentication pre-share encryption aes hash sha group 2 lifetime 86400 crypto isakmp policy 100 authentication crack encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 110 authentication rsa-sig encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 120 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 130 authentication crack encryption des hash sha group 2 lifetime 86400 crypto isakmp policy 140 authentication rsa-sig encryption des hash sha group 2 lifetime 86400 crypto isakmp policy 150 authentication pre-share encryption des hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet x.x.x.130 255.255.255.255 outside telnet timeout 5 ssh timeout 5 console timeout 0 management-access inside dhcpd address 192.168.197.25-192.168.197.100 inside dhcpd dns 192.168.180.232 68.87.74.162 interface inside dhcpd domain fphc.us interface inside dhcpd enable inside ! dhcprelay timeout 60 threat-detection basic-threat threat-detection statistics host threat-detection statistics protocol threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DfltGrpPolicy attributes vpn-filter value outside_1_cryptomap group-policy GroupPolicy_216.86.7.130 internal group-policy GroupPolicy_216.86.7.130 attributes vpn-filter value inside_nat0_outbound vpn-tunnel-protocol IPSec l2tp-ipsec tunnel-group x.x.x.130 type ipsec-l2l tunnel-group x.x.x.130 general-attributes default-group-policy GroupPolicy_216.86.7.130 tunnel-group x.x.x.130 ipsec-attributes pre-shared-key ***** tunnel-group-map default-group DefaultL2LGroup ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options inspect dns ! service-policy global_policy global prompt hostname context : end
Hello
The reason for the DECLINE suggests that the ASA has still attached to the L2L VPN VPN filter configuration that prevents traffic.
Check the configuration and remove atleast VPN filter temporarily for testing purposes.
-Jouni
-
WiFi comments at the Public VPN (ASA-5510)
Hello
I have an ASA 5510, that has the following configuration:
interface Ethernet0/0
nameif outside
security-level 0
address IP 1.1.1.1 255.255.255.240 (fake IP for obvious reasons)
interface Ethernet0/1
nameif inside
security-level 100
IP 192.168.0.200:ABCD 255.255.0.0
interface Ethernet0/2
nameif comments
security-level 100
IP 10.10.10.1 255.255.0.0
Global 1 interface (outside)
NAT (inside) 0 access-list sheep
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (guest) 0 access-list sheep
NAT (guest) 1 0.0.0.0 0.0.0.0
-------------------------------
What I do for a client (eth0/2) Wifi comments access to our VPN configured on the external interface? It is a Cisco AnyConnect VPN installation using the mobile client. As it is, they identify the DNS since the WAP and try to connect to "vpn.mysite.com", which resolves itself into the public IP (interface) outside my ASA.
When I was asked first to authorize this change, I thought it would be a simple NAT rule but I think I'm missing something that I can't get this to work.
Thank you
They are not capable of VPN for the external interface of the IP address of the guest network because it is by design not permitted.
They need to connect to the IP comments to be able to VPN to ASA comments network, and you will need to activate AnyConnect on the interface of comments as well. "vpn.mysite.com" would then need to resolve the IP comments when they are connected via the comments interface.
-
Hello
I want to configure SSL VPN for mobile users on ASA 5510 I have following requirements
> What are the condition of licence on ASA 5510 VPN with Anyconnect SSL?
> VPN users have full access to the local network via ASA
> Authentication method preferred, Local or AD (LDAP)
> users use not laptops should be limited to the Clientless SSL VPN
> How to add a URL is visible to users in the Web page
> Can someone view example configuration for the above requirements
TIA
Hitesh Vinzoda
> If you need both AnyConnect and WebVPN (Clientless SSL VPN), you can buy the AnyConnect Premium license (and this is a base user license). The ASA would come with default 2 SSL VPN license.
> To have full access to the local network, you must use AnyConnect SSL VPN. Here is an example of configuration:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00808efbd2.shtml
> You can authenticate to AD or Local or RADIUS, etc. By default, this would be local authentication.
> Here's some example configuration for clientless SSL VPN:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a008072462a.shtml
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00806ea271.shtml
Hope that helps.
-
How to end a vpn connection from site to site on ASA 5510
Hi guys,.
I would like to know if there is a command that I can use to break a connection from site to site and restart it whenever I want.
I don't want to use the close command since I use the specific interface as an exit point on the internet.
In this case, you can configure just one incomplete crypto map entry, for example: just keep 'peers set' not configured until you establish the vpn tunnel, and then add the command "set by the peers.
If you disable the tunnel, just remove the 'set by the peers' command for this particular VPN tunnel.
-
Site to Site VPN between 5510 and 5505
Am trying to get a VPN site-to site and the race between a branch office and our main office. I have the settings in place, but I'm trying to determine if it's my settings or the provider DSL, Verizon.
They have a 5505 with a static IP is connected by cable modem. Their 5505 I can ping external IP of my 5510 without problem. All the settings are correct on both sides; they reflect the same settings and yet static VPN is not launched.
Is there some sort of CLI command I must issue to bring it?
Also, I was wondering if maybe my 2821 prevents all VPN traffic because it doesn't have to be re - NAT'ed to the 192.168.250.0/23 and 192.168.252.0/24 subnets.
Simply to traffic of their 192.168.40.0 in our 192.168.250.0/23 VOIP subnet subnet.
Join a basic outline. I can provide the configs for almost everything
Hello
you have two instances of sequence card crypto with parameters similar (except transform set). Get rid of the rest of sequences card crypto:
On the ASA Satellite:
no card crypto outside_map 2 match address outside_cryptomap
no card crypto outside_map 2 set pfs
no card crypto outside_map 2 peers set smivpn.sorensonmedia.com
no card crypto outside_map 2 the transform-set ESP-3DES-MD5 value
No crypto outside_map 2 set security-association life card seconds 28800
No kilobytes of life card crypto outside_map 2 set security-association 4608000
no card crypto outside_map 2 the value reverse-road
About the ASA company:
No crypto outside_map 1 game card address outside_1_cryptomap_1
no card crypto outside_map 1 set pfs
no card crypto outside_map 1 set cda.asa5505 counterpart
no card crypto outside_map 1 the value transform-set ESP-3DES-SHA
no card crypto outside_map 1 lifetime of security association set seconds 28800
No kilobytes of life card crypto outside_map 1 set security-association 4608000
no card crypto outside_map 1 the value reverse-road
Then check and capture debugs.
HTH
Sangaré
-
site-to-site between ASA 5510 (8.4 (2)) w / static IP and Dlink DIR130 w / dynamic IP.
I'm trying to implement a VPN site link to site between the ASA5510 we use exclusively as a VPN endpoint on campus and a D-Link DIR130 router off campus, to a local company with a dynamically assigned IP address. We currently use the ASA to remote access users who use the Cisco VPN client on mobile devices, as well as a link to site-to-site unique in our telecommunications provider for the purposes of remote monitoring telecoms equipment.
We are looking for a way to deploy at a lower cost of VPN connections for local businesses to allow them to use the devices for sale which connect to systems on campus, so students can use their meal in local restaurants cards, similar to the way they use them in the cafeteria on campus.
I have experience setting up Cisco switches, routers and APs, but ASA appliance absolutely baffles me. I futzed with the AMPS 6.4 config autour gui and tried to match the configurations between the DIR130 and the ASA, but I can never get a VPN to come. Anyone who can point me to an example, or provide me with help on this would be appreciated. I have google searched and found very little, with my limited experience in setting up ASA, I ask to my script.
You must configure the static route on the 6509 for 192.168.5.0/24 to ASA inside the interface:
IP route 192.168.5.0 255.255.255.0 131.162.160.2
Assuming that 131.162.160.1 is your 6509
-
Site to site VPN (ASA-> router IOS, with two interfaces) help
Dear,
I need help to configure VPN from Site to Site of cisco ASA to the IOS router, the router has 2 WAN links, a primary and secondary backup.
There was only a single week of link there is, now we have installed the second link as a backup, we use OSPF as the routing protocol.
VPN with simple link worked fine, now, when the main link fails the network is down.
Waiting for response.
There is an easy solution. On the router, you must terminate the VPN on the loopback interface.
something like this:
interface lo0
IP x.x.x.x where x.x.x.x
card crypto-address lo0
interface wan_1
vpn crypto card
interface wan_2
vpn crypto card
One condition is that the loopback interface has accessible by the device of the SAA.
-
VPN - ASA 5510 L2L: internal error...
Hello
I'm trying to connect an astaro by l2l - vpn firewall to an asa5510.
I still have the following message.
Who is wrong? (checked the settings already)
Concerning
Marc
ASA % ASA-4-713903: Group = x.x.x.x, IP = x.x.x.x, memory previously allocated release for authorization-dn-attributes
ASA % ASA-3-713119: Group = x.x.x.x, IP = x.x.x.x, PHASE 1 COMPLETED
ASA % ASA-5-713904: Group = x.x.x.x, IP = x.x.x.x, IPSec security association proposals found unacceptable.
ASA % ASA-3-713902: Group = x.x.x.x IP x.x.x.x, QM WSF error = (P2 struct & 0x7bc32f0, mess id 0xc5da78b7).
ASA % ASA-3-713902: Group = x.x.x.x, IP = x.x.x.x, removing counterpart of correlator table failed, no match!
ASA % ASA-3-713231: Group = x.x.x.x, IP = x.x.x.x, Internal Error, ike_lock try to unlock the little that it is not locked for type SA_LOCK_P1_SA_CREATE
ASA % ASA-3-713232: Group = x.x.x.x, IP = x.x.x.x, ITS lock refCnt = 0, the bitmask = 00000000, p1_decrypt_cb = 0, qm_decrypt_cb = 1, qm_hash_cb = 0, qm_spi_ok_cb = 0, qm_dh_cb = 0, qm_secret_key_cb = 0, qm_encrypt_cb = 0
ASA % ASA-3-713902: Group = x.x.x.x, IP = x.x.x.x, removing counterpart of correlator table failed, no match!
ASA % ASA-4-113019: Group = x.x.x.x, Username = x.x.x.x, IP = x.x.x.x, disconnected Session. Session type: IPSecLAN2LAN, duration: 0 h: 00 m: 00s, xmt bytes: 0, RRs bytes: 0, right: Phase 2 Mismatch
Thanks Marc.
Eric
214.298.7610
-
Cisco ASA 5510 L2L VPN on the backup interface
OK, here is what I have and I even if I knew how to do this, but it has not worked for me. I hope someone out there can help you.
I have an ASA 5510 running 8.4 with double configuration of ISPs on 2 different interfaces: outside (primary), backup (backup). I also have a site to site VPN ASA another in another city. The VPN is now configured on the external interface and works very well. What I wanted to do, is to make the VPN running on backup interface only.
So, I changed the card encryption on the remote side to use the backup interface IP and created a tunnel-group for her. Then, I created a map encryption for backup interface and activated ikev1 on it. The default route is configured to use the external interface, so I created a static route that routes traffic destined for the external interface of the remote side to the backup interface default gateway. I can get to establish tunnels, but no traffic passes through them. I have however while I need a NAT device for the tunnel traffic to I created a NAT so but still no transmitted traffic. I tried the packet - trace and he said: the traffic was allowed and show its crypto ipsec command, I see the configuration of the tunnel, but no traffic will pass through it. Can anyone help?
Ben,
you use a code to version 8.4, I recommend starting by removing the config NAT statements at both ends. This version does not have the NAT and control, and if you don't need... I've seen instances with 8.4 (3) where a NAT even though apparently correct was causing not to pass through the traffic.
Site A:
NAT (inside, backup) source static obj-SiteALAN obj-SiteALAN static obj-SiteBLAN obj-SiteBLAN
Site b:
NAT (inside, outside) source static obj - 192.168.5.0 obj - 192.168.5.0 destination static obj - 192.168.3.0 obj - 192.168.3.0
If possible, you should increase your AES encryption, but this is a personal point of view and should not stop the traffic through the links. You should be able to see the counters for the data transmitted / received are these incrementing?
Do you have the ACLs that are from the inside to the outside and internal interface to the Interface of backup (duplicated.
In this model, the control is the routing.
Best regards
Ju
-
VPN site to Site ASA 5510 and 871 w / dynamic IP
What is the best method of creating a VPN site-to site between an ASA 5510 and a router 871 where the 5510 has a static IP address and has 871, a dynamic IP address?
My ASA is running ASA software version 7.0 (5) and I can't find how to create a tunnel for a dynamic IP address via the ASDM. I have currently a tunnel between these two arrangements in place, but it was done by specifying the remote IP address, even if it is dynamic.
Any suggestions or pointers would be * very * appreciated.
-Adam
This can help but it does not show ASDM.
-
ASA 5505 and ASA 5510 Site to Site VPN Tunnel cannot be established
Hi all experts
We are now plan to form an IPSec VPN tunnel from site to site between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failed, would you please show me how to establish? A reference guide?
I got error syslog 713902 and 713903, how to fix?
I got the following, when I type "sh crypto isakmp his."
Type: user role: initiator
Generate a new key: no State: MM_WAIT_MSG2
Hugo
Hello
This State is reached when the policies of the phase 1 do not correspond to the two ends.
Please confirm that you have the same settings of phase 1 on both sides with the following commands:
See the isakmp crypto race
See the race ikev1 crypto
Also make sure that port UDP 500 and 4500 are open for communication between your device and the remote peer.
Finally, make sure you have a route suitable for the remote VPN endpoint device.
Hope that helps.
Kind regards
Dinesh Moudgil
Maybe you are looking for
-
The problem is not with the HP Mini. This computer is running Windows 7 Starter and he Hotsyncs perfectly with my Tungsten C handheld. The problem is with a Dell Vostro, but because it is a problem of Palm, I hope you can help. My Dell Vostro has bee
-
Tecra R10 - 14 c - very slow start
Hi all I have Tecra R10 - 14 c and with software recover Windows Vista Business 32-bit all the time when I turn on the laptop, it takes a long time (from 15 to 25 m) to start Windows, comes in turn on laptop. But when I restart Windows Notepad is nor
-
Tried the boot failure, etc, but not good, were not the original windows disks Duplicate thread: URL: http://answers.microsoft.com/en-us/windows/forum/windows_vista-system/browseuidll-was-not-found/7ef0bd88-ec8f-4a5a-bde2-43d0f94cab03 Title: BROWSEUI
-
Why my RAM runs always at 50% or more?
My computer still seem to "work" even when I do nothing. The CPU usage is intermittent, up to 20% or more, but the ram is still high. This slows down what I try to do. Thank you Dennis
-
Hello I'm about to migrate from a stand alone to a sustained WLC WLAN infrastructure. I'll install a 4402-50 and I have a question regarding AP-manager interfaces. I read that each port supports up to 48 25 APs best practice and that the APs will dec