Site2Site and remote VPN

Similar Questions

• WebVPN and remote VPN access

  Hello

  Is there a difference between WebVPN and remote VPN access or they are the same.

  Thank you.

  access remote vpn consists of

  -IPSEC VPN remote access. It is part of the ASA, no permit required, requires pre-installed Client from Cisco VPN IPSEC on PC

  -with AnyConnect SSL VPN remote access. It requires licensing of SSL VPN on SAA. AnyConnect client can be installed automatically on the PC with the launch of web.

  -with Essentials AnyConnect SSL VPN remote access. Beginning with ASA 8.2 (1), almost license $ 0. It's the same AnyConnect client as in the previous article, but it cannot be installed automatically with the launch of web. It must be previously installed as of Cisco IPSEC VPN client.

  -webvpn aka clientless vpn. It is a portal HTTPS which allows HTTP connections, file sharing, telnet, RDP and much more (with smart tunnels) resources without having to install a real client on the PC. It requires licensing of SSL VPN on SAA. It cannot be used if "AnyConnect Essentials" license is activated on SAA after 8.2 (1)

  Kind regards

  Roman

• WebVPN and remote vpn, ssl vpn anyconnect

  Hi all

  Differences between webvpn and remote vpn, ssl vpn anyconnect
  All require a separate license?

  Thank you

  Hello

  The difference between the webvpn and SSL VPN Client is the WebVPN to use SSL/TLS and port

  send through a java application to support the application, it also only supports TCP for unicast traffic, no ip address

  address is assigned to the customer, and the navigation on the web in the tunnel is made with a SSL

  Web-mangle that allows us stuff things in theSSL session.

  SSL VPN (Anyconnect) Client is a client of complete tunneling using SSL/TCP, which installs an application on the computer and

  envelopes vpn traffic in the ssl session and thus also an assigned ip address has the

  tunnel's two-way, not one-way.   It allows for the support of the application on the

  tunnel without having to configure a port forward for each application.

  AnyConnect is a client of new generation, which has replaced the old vpn client and can be used as long as the IPSEC vpn ssl.

  For anyconnect licenses please see the link below:

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  Kind regards

  Kanwal

• You try to run a Site to site VPN and remote VPN from the same IP remotely

  We currently have a site to site VPN configuration between our offices call center and a 3rd party that allows them to access our training to their employees to use environment while being trained on our systems. This tunnel is running between our ASA and their ASA without problem; However, when we have managers come out to the call center, they are unable to use remote VPN to access our office.

  Apparently the same IP peer remote that we use for our site to the other tunnel is the same IP that our managers use to access the internet when they are on-site with the customer. When I look at the logs it shows the VPN attempt and then I get treatment Information Exchange has failed. So from what I can understand when our managers are trying to connect to our firewall from the same IP address as the counterpart of site to site it automatically tries to create a tunnel, according to the information of the site to the other tunnel. If our managers are anywhere else, they can connect through remote VPN with no problems.

  My question is if anyone knows of a way to make the firewall allow VPN site to site and remote connections with the same remote IP address.

  Hi John,.

  Basically, in older versions, when you hit a static encryption card and you does not match this static encryption completely map the connection continues until the dynamic encryption card. For this reason, you can connect your IPSec clients before. A bug has been opened on this vulnerability.

  CSCuc75090  Details of bug

  The crypto IPSec Security Association are created by dynamic crypto map to static peers

  Symptom:

  When a static VPN peer adds all traffic to the ACL crypto, a surveillance society is based even if the pair IP is not allowed in the acl to the main façade encryption. Are these SA finally put in correspondence and commissioning the dynamic crypto map instance.

  Conditions:

  It was a planned design since the first day that allowed customers to fall through in the case of static crypto map did not provide a necessary cryptographic services.

  The SA must be made from a peer configured statically and a dynamic crypto map instance must be configured on the receiving end.

  Workaround solution:

  N/A

  Some possible workarounds are:

  Configure a static nat device when you try to use the remote VPN if the firewall remotely will be hit with a different public IP address. It would be a good solution, but it will depend on how many ip addresses public you have available, if you really want one of these ip addresses for that access.

  Also, I thought you could use AnyConnect instead of the IPSec VPN client. I don't know how many users need to connect from your PC to the remote site, but the ASA has 2 licenses SSL available that you could use. Because Anyconnect uses the SSL protocol, it won't have a problem on your environment.

  Below some information:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa84/configuration/guide/asa_84_cli_config/vpn_anyconnect.html

  Hope this helps,

  Luis.

• Routing of a VPN from Site to site to remote VPN users

  Hello

  We have a site and remote vpn site configured in the same interface in ASA 5520 (software version 8.3). When the remote vpn users try to connect to the computers located at the far end of the site to site VPN, their request has failed. I tried No.-Nat between remote vpn IP private to the private IP address of remote site, also said the same split tunneling. I can't find even the tracert, ping has also expired.

  Is there any solution to make this live thing.

  Shankar.

  There are a few things that need to be added to make it work:

  (1) on the SAA where remote vpn users connect to, you must add "permit same-security-traffic intra-interface"

  (2) you mention that you have added the LAN of remote site-to-site in the list of split tunnel, so that's good.

  (3) on the SAA ending the vpn for remote access, you must also add the following text:

  -Crypto ACL for the site to site VPN must include the following:

  permit ip access list

  (4) on the ASA site to remote site, you must add:

  -Crypto ACL for the site to site VPN must include the following:

  permit ip access list

  -No - Nat: ip access list allow

• ASA Version 9.0 (1) - Ping works both inside and outside, WWW does not work for remote VPN

  I am at a loss, I can connect VIA VPN and Ping inside the IPs (192.168.1.2) and outside (4.2.2.2) IPs of the remote VPN client, but can't surf WWW. Inside the network, all users have WWW access and the network is fine. I'm new on the revisions to ver 8.3 and don't see what I'm missing?

  Info:

  ASA-A # sh xl
  in use, the most used 12 4
  Flags: D - DNS, e - extended, I - identity, i - dynamics, r - portmap,
  s - static, T - twice, N - net-to-net
  NAT inside:192.168.1.0/24 to outside:24.180.x.x/24
  flags s idle 0:10:46 timeout 0:00:00
  NAT outside:192.168.2.0/24 to outside:24.180.x./24
  flags s idle 0:00:59 timeout 0:00:00
  NAT inside:192.168.1.0/24 to any:192.168.1.0/24
  sitting inactive flags 0:11:51 timeout 0:00:00
  NAT any:192.168.2.0/24 to inside:192.168.2.0/24
  sitting inactive flags 0:11:51 timeout 0:00:00
  ASA-A #.

  ASA-A # sh nat
  Manual NAT policies (Section 1)
  1 (inside) to destination of (all) Inside_Net Inside_Net the VPN-NET VPN static static
  translate_hits = 3, untranslate_hits = 3

  Auto NAT policies (Section 2)
  1 (inside) (outside) static source Inside_Net 24.180.x.x
  translate_hits = 3, untranslate_hits = 184
  2 (outdoor) (outdoor) static source VPN-net 24.180.x.x
  translate_hits 97, untranslate_hits = 91 =
  ASA-A #.

  Journal of the Sho:

  % 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; Connection for udp src outside:192.168.2.10/137(LOCAL\User) dst outside:192.168.2.255/137 refused due to path failure reverse that of NAT
  % ASA-609002 7: duration of outside local host: 192.168.2.255 disassembly 0:00:00
  % ASA-609001 7: built outside local host: 192.168.2.255

  % 305013-5-ASA: rules asymmetrical NAT matched for flows forward and backward; Connection for udp src outside:192.168.2.10/137(LOCAL\User) dst outside:192.168.2.255/137 refused due to path failure reverse that of NAT
  % ASA-609002 7: duration of outside local host: 192.168.2.255 disassembly 0:00:00

  Current config:

  ASA Version 9.0 (1)
  !
  ASA-A host name
  domain a.local
  enable the encrypted password xxxxx
  XXXXX encrypted passwd
  names of
  IP local pool vpnpool 192.168.2.10 - 192.168.2.20
  !
  interface Ethernet0/0
  Inet connection description
  switchport access vlan 2
  !
  interface Ethernet0/1
  LAN connection description
  switchport access vlan 3
  !
  interface Ethernet0/2
  switchport access vlan 3
  !
  interface Ethernet0/3
  switchport access vlan 3
  !
  interface Ethernet0/4
  switchport access vlan 3
  !
  interface Ethernet0/5
  switchport access vlan 3
  !
  interface Ethernet0/6
  switchport access vlan 3
  !
  interface Ethernet0/7
  switchport access vlan 3
  !
  interface Vlan1
  No nameif
  no level of security
  no ip address
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP address 24.180.x.x 255.255.255.248
  !
  interface Vlan3
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  banner exec   ********************************************
  banner exec   *                                          *
  exec banner * ASA-A *.
  banner exec   *                                          *
  exec banner * CISCO ASA5505 *.
  banner exec   *                                          *
  exec banner * A Services Inc.              *
  exec banner * xxx in car Street N. *.
  exec banner * city, ST # *.
  banner exec   *                                          *
  banner exec   ********************************************
  exec banner ^
  passive FTP mode
  DNS server-group DefaultDNS
  domain a.local
  permit same-security-traffic intra-interface
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  network of the Inside_Net object
  subnet 192.168.1.0 255.255.255.0
  network of the VPN-net object
  Subnet 192.168.2.0 255.255.255.0
  access-list extended sheep permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
  allowed incoming access extended gre a whole list
  inbound udp allowed extended access list any host 24.180.x.x eq 1723
  list of allowed inbound tcp extended access any host 24.180.x.x eq pptp
  list of allowed inbound tcp extended access any host 24.180.x.x eq smtp
  list of allowed inbound tcp extended access any host 24.180.x.x eq www
  list of allowed inbound tcp extended access any host 24.180.x.x eq https
  list of allowed inbound tcp extended access any host 24.180.x.x eq 987
  inbound udp allowed extended access list any host 24.180.x.x eq 25
  inbound udp allowed extended access list any host 24.180.x.x eq 443
  inbound udp allowed extended access list any host 24.180.x.x eq www
  inbound udp allowed extended access list any host 24.180.x.x eq 987
  pager lines 24
  Enable logging
  debug logging in buffered memory
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow all outside
  ICMP allow any inside
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  public static Inside_Net Inside_Net destination NAT (inside, all) static source VPN-NET VPN
  !
  network of the Inside_Net object
  NAT static 24.180.x.x (indoor, outdoor)
  network of the VPN-net object
  24.180.x.x static NAT (outdoors, outdoor)
  Access-group interface incoming outside
  Route outside 0.0.0.0 0.0.0.0 24.180.x.x 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  Enable http server
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
  Crypto ipsec transform-set ikev1 VPN remote esp-3des esp-md5-hmac
  Crypto ipsec ikev2 VPN ipsec-proposal-remotetest
  Protocol esp encryption aes - 256, aes - 192, aes, 3des and
  Esp integrity sha-1 protocol
  Crypto ipsec pmtu aging infinite - the security association
  Crypto-map dynamic dyn1 1jeu ikev1 transform-set remote VPN
  Crypto-map dynamic dyn1 1jeu reverse-road
  map VPN - map 1-isakmp ipsec crypto dynamic dyn1
  VPN-card interface card crypto outside
  Crypto ca trustpoint _SmartCallHome_ServerCA
  Configure CRL
  trustpool crypto ca policy
  Crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
  6c2527b9 deb78458 c61f381e a4c4cb66
  quit smoking
  Crypto ikev1 allow outside
  IKEv1 crypto policy 1
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 43200
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0

  dhcpd outside auto_config
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  user name UName encrypted password privilege 15 xxxxxxxxx
  type tunnel-group remote VPN remote access
  attributes global-tunnel-group VPN-remote controls
  address vpnpool pool
  tunnel-group, ipsec VPN-remote controls-attributes
  IKEv1 pre-shared-key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  anonymous reporting remote call
  Cryptochecksum:43db9ab2d3427289fb9a0fdb22b551fa
  : end

  Hello

  Its propably because you do not have a DNS server configured for VPN users. Try this command:

   group-policy DfltGrpPolicy attributes dns-server value 8.8.8.8

• Tunnel VPN remote Internet and VPN remote VPN from Site to Site traffic?

  Hello

  We try to remote traffic from our users VPN tunnel through our ASA 5510 as well as to allow the only access for remote user VPN traffic to the other end of the all our VPN site-to-site connected to the same ASA. Basically, we who want to VPN in the network in order to access all of our networks business. We try to get away with this without using split Tunneling.

  I can currently get internal traffic from the remote user VPN to reach all other vpn site-to-site tunnels without the internet in tunnel. The problem is when I add the following statement to the NAT:

  NAT (outside) 1 10.10.19.0 255.255.255.0 * 10.10.19.0 is the address of the remote VPN Client

  Internet traffic to the remote VPN starts to get in the tunnel, but I lose the opportunity to reach one of the other tunnels from site to site by the remote VPN tunnel.

  I also begin to receive the following errors in the journal of the ASA

  3 July 1, 2009 12:34:18 305005 10.10.19.255 137 no group of translation not found for udp src outside:10.10.19.3/137 dst outside:10.10.19.255/137

  Any help with how NAT statements must be defined for this work would be appreciated.

  Thank you

  Will be

  Will,

  the link of this post for your scenario of vpn hub & speak reference, you problem may be on exempt nat rules.

  Have a second look at your sheep rules.

  Be sure to eliminate tunnel rules related to rheumatoid arthritis, as appropriate, to not let him get in the way of splitting.

  http://forums.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=security&topic=firewalling&TopicId=.ee6e1fa&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2e0f6/4

  If always emits discribe topology for l2ls and info logic RA and sanatized hub config asa... but I think if you look at the thread above, you should be able to solve.

  Concerning

• Remote VPN client and Telnet to ASA

  Hi guys

  I have an ASA connected to the Cisco 2821 router firewall.

  I have the router ADSL and lease line connected.

  All my traffic for web ports etc. of ADSL ftp and smtp pop3, telnet etc is going to rental online.

  My questions as follows:

  I am unable to telnet to ASA outside Interface although its configuered.

  Unable to connect my remote VPN Client, there is no package debug crypto isakmp, I know that I have a nat that is my before router device my asa, I owe not nat port 4500 and esp more there, but how his confusion.

  I'm ataching configuration.

  Concerning

  It looks like a config issue. Possibly need debug output "debug crypto isa 127".

  You may need remove the command «LOCAL authority-server-group»

  NAT-traversal is enabled by default on the ASA 8.x version. So you don't have to worry about NAT device in the middle.

• L2L pix 501 and remote access VPN

  Hi, I'm working on an old 501 PIX w / Software 6.3 (5), he already have access to remote VPN configuration and works very well, but now he needs a L2L implemented. One thing I try to do all the work remotely via VPN or ssh to the machine. I don't know what's on the other end, but they swear that it is set up and maybe my problem is when I start putting in orders for the other VPN it breaks the remote VPN access. One thing that I have to do is NAT a host on the inside to appear as another host on the end. I use these commands and I think it works cannot be said.

  access-list 101 permit ip remote_network 255.255.255.0 local_server host

  public static 10.1.0.203 (inside, outside) - access list 101

  then

  access-list 102 permit ip host 10.1.0.203 192.168.50.83
  access-list 102 permit ip host 10.1.0.203 192.168.50.86
  access-list 102 permit ip host 10.1.0.203 192.168.50.50
  access-list 102 permit ip host 10.1.0.203 192.168.50.85

  and use it to match against

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  EMDs-map 10 ipsec-isakmp crypto map
  correspondence address card crypto emds-map 10 102
  card crypto emds-map 10 peers set remote_vpn_server
  card crypto emds-card 10 set of transformation-ESP-3DES-SHA

  then

  ISAKMP key magic_key address remote_vpn_server netmask 255.255.255.255
  ISAKMP identity hostname
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 sha hash
  10 1 ISAKMP policy group
  ISAKMP life duration strategy 10 86400

  and that is where it usually breaks the VPN, I don't know if the other VPN works due to not being not able to get to this server to try to ping, I don't really like to try this stuff remotely but I don't have a lot of choice at the moment.

  Any thoughts?

  Thank you

  Jarrid Graham

  Yes, just use the number of different sequence with 1 name of the crypto map. Please also ensure that your dynamic crypto map, which is your vpn client has the sequence down the crypto map (more), because you want to make sure that the static crypto map (for lan-to-lan tunnel has higher sequence number (lower number)).

  The political isakmp sequence number does not match, it is processed from top to bottom (number less than the high number) and also long 1 set of isakmp policy corresponds to the remote peer, it will be negotiated properly.

  Hope that answers your question and please note useful post. Thank you.

• remote VPN and vpn site to site vpn remote users unable to access the local network

  As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config

  The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.

  ASA Version 8.2 (2)
  !
  host name
  domain kunchevrolet
  activate r8xwsBuKsSP7kABz encrypted password
  r8xwsBuKsSP7kABz encrypted passwd
  names of
  !
  interface Ethernet0/0
  nameif outside
  security-level 0
  PPPoE client vpdn group dataone
  IP address pppoe
  !
  interface Ethernet0/1
  nameif inside
  security-level 50
  IP 192.168.215.2 255.255.255.0
  !
  interface Ethernet0/2
  nameif Internet
  security-level 0
  IP address dhcp setroute
  !
  interface Ethernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  Shutdown
  No nameif
  no level of security
  no ip address
  management only
  !
  passive FTP mode
  clock timezone IST 5 30
  DNS server-group DefaultDNS
  domain kunchevrolet
  permit same-security-traffic intra-interface
  object-group network GM-DC-VPN-Gateway
  object-group, net-LAN
  access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
  tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Outside 1500 MTU
  Within 1500 MTU
  MTU 1500 Internet
  IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
  ICMP unreachable rate-limit 1 burst-size 1
  enable ASDM history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  the ssh LOCAL console AAA authentication
  AAA authentication LOCAL telnet console
  AAA authentication http LOCAL console
  AAA authentication enable LOCAL console
  LOCAL AAA authentication serial console
  Enable http server
  x.x.x.x 255.255.255.252 out http
  http 192.168.215.0 255.255.255.252 inside
  http 192.168.215.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto-map dynamic dynmap 65500 transform-set RIGHT
  card crypto 10 VPN ipsec-isakmp dynamic dynmap
  card crypto VPN outside interface
  card crypto 10 ASA-01 set peer 221.135.138.130
  card crypto 10 ASA - 01 the transform-set RIGHT value
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 65535
  preshared authentication
  the Encryption
  sha hash
  Group 2
  lifetime 28800
  Telnet 192.168.215.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  Console timeout 0
  management-access inside
  VPDN group dataone request dialout pppoe
  VPDN group dataone localname bb4027654187_scdrid
  VPDN group dataone ppp authentication chap
  VPDN username bb4027654187_scdrid password * local store
  interface for identifying DHCP-client Internet customer
  dhcpd dns 218.248.255.141 218.248.245.1
  !
  dhcpd address 192.168.215.11 - 192.168.215.254 inside
  dhcpd allow inside
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Des-sha1 encryption SSL
  WebVPN
  allow outside
  tunnel-group-list activate
  internal kun group policy
  kun group policy attributes
  VPN - connections 8
  Protocol-tunnel-VPN IPSec
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value split tunnel
  kunchevrolet value by default-field
  test P4ttSyrm33SV8TYp encrypted password username
  username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
  username kunauto attributes
  Strategy Group-VPN-kun
  Protocol-tunnel-VPN IPSec
  tunnel-group vpngroup type remote access
  tunnel-group vpngroup General attributes
  address pool VPN_Users
  Group Policy - by default-kun
  tunnel-group vpngroup webvpn-attributes
  the vpngroup group alias activation
  vpngroup group tunnel ipsec-attributes
  pre-shared key *.
  type tunnel-group test remote access
  tunnel-group x.x.x.x type ipsec-l2l
  tunnel-group ipsec-attributes x.x.x.x
  pre-shared key *.
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  Review the ip options
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  inspect the icmp
  !
  global service-policy global_policy
  context of prompt hostname
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
  : end
  kunauto #.

  Hello

  Looking at the configuration, there is an access list this nat exemption: -.

  192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0

  But it is not applied in the States of nat.

  Send the following command to the nat exemption to apply: -.

  NAT (inside) 0 access-list sheep

  Kind regards

  Dinesh Moudgil

  P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community

• Site to Site VPN and remote access on PIX 6.3 (3)

  Hello

  I have a vpn site-to site to remote access configured on the pix device. Everything works like a charm until I decide to perform authentication of the local client for remote vpn clients using the same card encryption from site to site. Thus, the tunnel from site to site is broken because that is trying to authenticate the local user.

  Is it possible to use the authentication of the remote local user for vpn clients on PIX without breaking other tunnels that use the same cryptomap?

  If the answer is to use separate crypro card so how can I assign the other encryption to use outside of the interface card, if only a single encryption card can be assigned to any given interface?

  When you configure the isakmp key, use the command

  ISAKMP KeyString keys by the peer-address [mask netmask] [No.-xauth] [No.-config-mode]

  No.-xauth will tell the isakmp won't the isakmp xauth for L2L and non-config-mode does not distribute the ip address of the peer L2L.

  Let us know if it works

  -Vikas

• EasyVPN and access VPN remotely on the same box

  Is it possible to have a config EasyVPN and remote access in the same box? I tried to do that and when I do a vpnclient enable command he said remote NAT (outside) 0

  Router IOS or PIX? EzVPN server or client?

  If it's EzVPN server, then it's basically a configuration of remote access also, then Yes, you can certainly have them both, actually just set one up and you get one anyway.

  If it's EzVPN client, then no if it is a PIX and Yes if it's a router, but you must run 12.2 (15) T, see http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/ftezvpnr.htm#1155828 for more details.

  Please answer back with more information on exactly what you're trying to do, it is a little difficult to your original explanation.

• QuickVPN - could not do a ping the remote VPN router!

  Hello

  I have a RV042 (VPN router) and I have some problems to run properly using the QuickVPN client.

  Here is the Log of the QuickVPN client.

  2008-10-15 20:14:38 [STATUS] a network interface detected with 192.168.0.104 IP address
  2008-10-15 20:14:38 [STATUS] connection...
  2008-10-15 20:14:38 [STATUS] connection to a remote gateway with IP address: 96.20.174.84
  2008-10-15 20:14:38 [WARNING] server certificate does not exist on your local computer.
  2008-10-15 20:14:44 remote gateway [STATE] has been reached with https...
  2008-10-15 20:14:44 [STATUS] commissioning...
  2008-10-15 20:14:51 [STATUS] Tunnel is connected successfully.
  2008-10-15 20:14:51 [STATUS] verification of network...
  2008-10-15 20:14:55 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:14:58 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:01 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:05 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:08 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:11 [WARNING] Ping has been blocked, which can be caused by an unexpected disconnection.
  2008-10-15 20:15:19 [STATUS] disconnection...
  2008-10-15 20:15:25 [STATUS] Tunnel is disconnected successfully.

  I don't know how it is implemented, but if WuickVPN wait a form ping my router, it will not happen. I was never able to ping my router ouside of my ISP network.

  There is a way to disable the Ping process and continue with the VPN connection?

  QuickVPN try ping on the router via the VPN tunnel to check the connection. It should work without worrying about whether your ISP filters ICMP messages or not. The tunnel is encrypted your ISP won't know what you're doing.

  Please post the corresponding on the RV042 VPN log. That is expected to see how far you get.

  You have a firewall running on the computer? I think that some firewalls have difficulty with the traffic of ESP.

  What is the router that is connected to the computer? How is it that is configured?

• RV082 and fast VPN

  I tried to configure my router RV082 all OE quick VPN access. I bought this router a few years back with the intention of setting up a VPN. Now that I need to do, this product is no longer supported.

  In any case, down to the problem - I can not past the first problem. I get an error that says: "Unable to connect" and it lists 5 problems:

  1. wrong password

  2. no IP address for the network card

  3. incorrect server address

  4. you may need to disable your windows firewall

  5. conflicts of IP addresses with the subnet of the remote VPN server

  I just tackle these questions

  1. I am using the correct password

  2. I have an IP address, I can get on the internet

  3 server address is correct

  4. do not use the windows firewall (I have even disabled my firewall, netgear home but no help)

  5. work 192.168.0.x subnet, host is 192.168.1.x, different subnets.

  When I'm at home, I can connect to the remote router configuration page, but I can't get anywhere with fast VPN. I tried this on 3 different networks, all give me the same answer. I am inclined to believe that this must mean I'm incorrectly configured on the router, but I followed all the steps as described by linksys. I even upgraded to the latest firmware and the latest version of quickVPN all to nothing does not.

  I use access rules to guide the SQL traffic to one of our servers, that is the question? Any ideas?

  Thank you for your response. You are right it is not access rules, but it is the configuration of the router. In the tab "Firewall", you need to enable HTTPS. There was nowhere in the product manual update, I downloaded, but it was on the info for the Firewall page tab. The only reason why that I disabled it HTTPS is that my remote management session with the previous firmware would sometimes close unexpectedly under HTTPS. In any case, connection works fine now.

  So my next question has to do with the speed. This is the first time I've gotten a quick VPN to work. When I connect to my ping time to a server is 60-80ms. At work, it is 1 ms. It is common to have a time big lag? Unfortunately at this slow speed this VPN may not be such a solution. I used a PPTP VPN in the past and latency are not too bad, but of course there is no encryption that is important here. Any thoughts on the speed?

• Connectivity to the remote VPN site adjacent networks

  Star topology with Corporate office which acts as hub (192.168.1.x) and remote sites connected by relay frames, except for another network (172.16.x.x) in the building served by 3560 switch company.

  On my remote site vpn (10.0.1.x) I can ping network 172.16.x.x, but not the 192.168.1.x network. What I'm trying to do is to allow the network traffic remote 10.0.1.x (which connects directly via the VPN network 172.16.x.x) to reach the network 192.168.1.x and vice versa.

  I'm sure its a combination of NAT/routing issue I forget.

  I'm new to PIX / ASA in general and it's the first vpn L2L I install. If someone can point me in the right direction, I would appreciate it.

  Thank you.

  It looks like this?

  10.0.1.x->-> Corp. ASA L2L tunnel - >->-> 192.168.1.x 3560 172.16.x.x

  and that you can currently communicate via the tunnel between 10.0 and 172.16? In order to communicate between 10.0 and 192.168.1, you will need to define this interesting traffic and add it to your crypto and nat exemption acl.

  Corp site

  extended access-list allow ip 192.168.1.0 255.255.255.0 10.0.1.0 255.255.255.0

  extended access-list allow ip 192.168.1.0 255.255.255.0 10.0.1.0 255.255.255.0

  NAT (inside) - 0 access list

  Remote site

  access-list extended ip 10.0.1.0 allow 255.255.255.0 192.168.1.0 255.255.255.0

  access-list extended ip 10.0.1.0 allow 255.255.255.0 192.168.1.0 255.255.255.0

  NAT (inside) - 0 access list