Similar Questions

• "Gateway router not found" error when you try to connect the TiVO DVR with DLink router.

  Original title: gateway router not found

  try to connect the tivo series 2 to the internet with dlink router that he used to work with previous tivo but not with tivo now, it says gateway router not found
  However, my laptop works fine with the router, I tried tivo support nothing helps, too, if I use the phone line works of tivo, but do not store a lot and is running out of room so it will not work fo rme, helllpppppppp thanks

  Hello

  Where exactly you get this error message?

  See the troubleshooting suggested in "Network error message N07 or C107" steps from this link.

  If you try to connect the tivo series 2 to the internet with dlink router then check out the link below:

  http://support.TiVo.com/app/answers/detail/A_ID/400

  Please contact the manufacturer.

• Linksys - router bridge - E8350 path not found network

  Dear community of Linksys,

  I recently bought a Linksys E8350 router, to replace the old AP in my network domestic.

  To make the installer of my clear network, I did a little diagram:

  

  So, as you can see, at the top left is the router/modem provided by my internet provider (Telenet, Belgium).

  I have a wired connection in my room, where I have my desktop and NAS connected computer. I also plugged the

  Linksys E8350 that is configured in Bridge mode. My laptop is connected wireless to the E8350.

  On the E8350, I disabled DHCP and NAT and gave him a static IP outside the range of my other router.

  My problem:

  When I go to the network through windows file Explorer, I can see my desktop from my laptop and vice versa.

  But when I double click to access one of them, I get the error message "network path not found".

  Connection via start > \\Computer-name gives the same error.

  Since my laptop or my desktop, I can see my NAS on the network. I have internet on all my devices:

  My office through internet cable connection, my laptop has wireless internet connection trough

  and I can evaluate my NAS from the internet.

  When I remove the E8350 entirely from my network and connect my laptop a hollow wired connection.

  everything works fine. I can see all the devices on the network, connect to my NAS and share files between computers.

  Things I tried already:

  -My PC and laptop are both in a 'private network '.

  -J' disabled my firewall

  -Everything is activated in the menu "sharing advanced settings."

  -J' tried to connect the E8350 to the switch via the Ethernet or WLAN port, nor to solve the problem

  -J' tried to change the NETBIOS settings

  -I don't have your antivirus software that might interfere with something

  -J' updated the firmware on my linksys router to the latest version

  To be clear, the problem occurs when I put the E8350 in my network, otherwise everything works perfectly.

  I hope that I have provided some information decent on my problem, because I can't seem to figure it out myself.

  Thank you in advance.

  Pindox

  The topology of your network is effective from your diagram. With the E8350 in mode bridge in this topology is WAN is connected to the network switch.

  Many devices of bridge no hand NetBios address very well. In some cases, the best way to access the network through a bridge device resources is to use remote devices IP address instead of its computer\device network name.

  In Windows, you can drive old school card NAS records using the IP address of the Servers\NAS:

  PC command line:

  NET use s: \\192.168.0.3\my_nas_folder / persistent: Yes

• Router not found - EA6500

  I'm configuring my settings of connectivity on my E6500. I type 192.168.1.1 and the logon screen comes up. I tried signing in with my username and password and also disconnect from the internet and the connection the router password. After that I connect, 98% of the time it says router not found you have not logged to your router. It's funny told me that since this Web page is provided from the router because I unplugged the internet. Even with the internet, it does the same thing.

  The time it loads the home page of the router, I click on connection and when it comes to the top, the page is just blank with buttons Ok, cancel, and apply.

  I did a reset on the router and it reconfigured with the CD and tried everything above again and same results.

  I don't remember which is a problem when I first set up the router, it seems that a new firmware has been installed automatically. I see no any info on what is a known problem with the latest firmware. Everyone knows about this problem?

  How you try to connect? 192.168.1.1? MyRouter.local? or www.ciscoconnectcloud.com ?
  Try to repair the connection to your computer or empty the cache of Dns resolution or the cache of the browser.

• I'm unable to watch videos on a certain type of site. They all now say, 'file not found '. They worked until I added a router for my Kindle Fire.

  I used to be able to watch videos on a certain type of site now all say file not found windows vista. I recently added a router for a kindle fire

  original title: streaming videos

  Hello

  ·          Do you mean that you use Internet Explorer 6 in Windows Vista?

  Windows Vista Internet Explorer 7 default features.

  http://Windows.Microsoft.com/en-us/Windows-Vista/find-out-which-version-of-Internet-Explorer-youre-using

• So, updated for Win 7. Clean install. 1. no installed audio device? 2 Ethernet adapter not found. Yes router does not. Planet WNRT - 617G

  Clean install. 2 problems. 1. no installed audio device? 2 Ethernet adapter not found. Yes router does not. Planet WNRT - 617G

  Probably you run first win7 Upgrade Advisor, who did you would probably show your system as not supported under win7

• Win7 64 bit, connects to the router, but no error internet access-"page not found".

  Original title: Win7 64 bit, connects to the router but no internet access.

  Help! Windows 7, XP Home Edition Premium, 64 bit, connects to the router and I can access the network. However, I can't access the internet. PC was working fine until a few days when I was using IE Explorer and I suddenly got the error "page not found". This pc internet connection uses the onboard network controller. I rebooted the pc and used the option "safe mode with network. The pc worked fine and I had access to the internet. I restarted the pc and still no access. I tried a usb wireless adapter. No luck. I have not installed updates or software recently. My other 2 PC works fine. I tried to use the network troubleshooter and he could not find any problems.

  Hello

  1. Have you made changes on the computer before this problem?
  2. What antivirus application do you use?

  I suggest you try these methods and check the status of the issue.

  Method 1:

  Keep the computer in a clean boot and check the status of the issue. If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem. Continue with the remaining steps to pin-point on the third party service. After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7.

  http://support.Microsoft.com/kb/929135

  Note: Please go up to step 7 of the Kb to maintain the computer to a normal startup after you fix the problem

  Method 2:

  I would suggest trying the following steps and check the status of the question.

  a. open Internet explorer.

  b. click on tools, then on Internet options.

  c. click on the Connections tab.

  d. click on LAN settings.

  e. uncheck the option use a proxy server for your LAN .

  f. save the changes by clicking on apply and ok.

  Method 3:

  Configure Internet Explorer to disable simplified HTTP error messages and check the status of the issue.

  a. on the Tools menu, click Internet Options.
   
  b. on the Advanced tab, in the browsing section, disable friendly HTTP error messages display check box and then click OK.

  c. close Internet Explorer.

  d. restart Internet explorer and check the status of the issue.

• END point URL for the routing service BSE says not FOUND

  Hi all

  For services of routing in BSE, the WSDL link opens the fine, but the link to endpoint URI for the routing service fails with the message below the message. When I invoke the WSDL with SOAP UI, I'll be back the same error message. I tried to bounce the server, but no help. I also noticed that this slide ESB_Projects Directory gives error 404 on any browser.

  Then, when I click below url for all the routing service

  http:// < hostname >: < port > /Event/ < systemName > / < serviceGroupName > /AddressStandardizeRS

  I get the error in the browser - below

  Not found

  The URL /event/ requested < the system name > / < group name > / < Routing Service name > was not found on this server.

  Oracle-Application-Server-10g/10.1.3.1.0 Oracle-HTTP-Server Server at odevsoa.local1.wbcgp.com Port 7777

• A small icon of 404 not found always appears at the bottom right of my screen everytime I open firefox, regardless the page I'll, it's still there in the same place

  I can go to either the page I like, but the little message is always that appear. He is just a paralilogram little 404 not found message whith and a strange server name.

  Thank you very much for your help, but I've uninstalled and reinstalled firefox and now it's over. I hope that it does not yet appear. If that's the case I'll follow your advice and post the things you said.

• Adapter not found

  I am running Windows 7 64 bit on my HP Pavilion dv6. I had never had any problems with my wifi, until I used a cable ethernet for a little while. Normally, my wifi works great. I get full signal and about 10 or so other networks bars appear in my area, and I can connect to wifi in public places and homes of others when I go out. Then, I used a cable ethernet home for a few days, to see if this helped a problem that we have with our router (internet cuts in and out sometimes, but that is not related to my concern). After that I restarted my computer once with the ethernet cable, the icon at the bottom right which shows my network has changed. He used to look like bars of signal, and when I clicked it I could see that I was connected to my home network with the internet and excellent signal strength, and I could see a list of other local networks. After reboot with ethernet cable, the icon has changed to a monitor with a cable ethernet beside him, and when I click on it it shows just my network. When I take the ethernet cable, my network disappears and it says that there are no available connections.

  Something was wrong with my wifi. I tried several methods via the control panel to set up a wireless network and internet, and I made sure several times my computer has active wireless. There is a button on my keyboard (f12 key), which shows a little light blue when wifi is on, and it becomes red when the wireless is turned off. I always make sure that the light is blue.

  When I clicked on 'Intel My Wifi Technology' in the Control Panel, a small window pops up which says 'Card network not found.' What does that mean? I lost a driver somehow? What can I do about it? I really need my wireless internet, especially for the school, if can I please get help? Thank you :-)

  Sometimes, when you use the cable ethernet wireless adapter is disabled. Open network and sharing of Center.In the left sidebar, click on "change the map settings. This should show ethernet and wireless adapters. The wireless, the value is disabled? If so, right-click and choose activate.

• Printer HP Photosmart 7525 Wizard is not found

  I need help to find my HP Photosmart e - all in a Wizard of the printer.  I want her to be as an icon on my desktop.  (Like Solution HP) used to do.

  I want to scan multiple images at once/harvest/and save each to a different file.

  Help

  emgerald

  Emgerald,

  Welcome to the HP Forum.

  Please keep with steps you have already done...

  First you must have installed full feature software.

  General instructions to install the printer software

  • Open drivers HP & downloads
  • Enter your printer model information
  • Select your printer in the list of the 'results '.

  OR

  ·         Open e-all-in-one printer, HP Photosmart 7525 drivers

  ·         Enter your operating system from the menu drop-down

  ·         Click NEXT and scroll down

  ·         Find the category driver - software product installation

  ·         Select the base driver, e-print, or a full features software

  ·         Save the *.exe installation package (s) on your computer

  The files will probably save in the "folder"downloads. "

  Next:

  • If it is available, you can download print and scan doctor and / or other programs of the category-utilities

  TIP:

  Install the utilities / tools first. bit installation packages are smaller in size

  • If you have control of "Admin", you can highlight the package and "double-click" to install it, otherwise just right-click, select run as administrator and install.

  NOTES:

  ·          On the bottom half of the main Web page for your printer, you can find some helpful videos to help with the installation of the printer software.

  ·          Scroll down the list of videos back until you find the video that best fits your situation.

  • If you use a USB connection: download and install the driver software before connecting a USB cable.
  • Ethernet: If the printer supports Ethernet, you can connect the printer to the network (and assign the printer an IP address for the router, if you wish).  Once the printer is connected to the network, make sure that the printer is turned on, and then install the printer software.
  • Once the initial installation is complete and functional, don't forget to check and install the relevant updates - check the category - updated

  There is valuable information about the Web site, including manuals, pages, solving problems, and SOLUTIONS to problems, How-to's and alerts for your printer.  Be sure to take a comprehensive look at what's available.  To bookmark the page.

  - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

  Setup software printer should provide an icon Printer Wizard on your desktop that you can use to "scan a Photo Document or".

  Shortcut:

  If the printer icon Wizard is not placed on the desktop during installation, then you can search for the program Assistant printer on your computer.

  Assuming that the printing software full feature software properly installed, you just find the program you can make your own shortcut to the printer for your Office Assistant.

  The following CAN help...

  • Open a Windows Explorer window
  • Go to C:\Program Files *
  • You might find a folder named for your printing software (photosmart 7525)
  • Navigate to the Bin subfolder
  • Search for a program called OR similar
  • NOTE: The program will NOT be appointed Assistant printer
  • Right click on this program > select send to desktop to make a shortcut

  ** Windows 7 may be different - look in C:\Program Files (x 86) \HP if you must, although I suspect the only program you will find there the scanner program...

  ============================================================================

  Multiple scan / crop to save a characteristic single file:

  There are two ways to end up with what you want, even if I have not found a way to get the 7520 (very similar to your model) to do what I think you are looking for.

  I agree that it is useful to have.   If we have zillions of old photos to scan, need to scan a photo at a time - or their cropping manually - can make your brain freeze.

  If the feature is available on your model, the magic is in the analysis in the Assistant printer model - and relaxation is perhaps not too much harder that separate the pictures far enough part to trigger the sensor reads what is on the glass.  It's been a while since I've done this - but I'm sure it was pretty straightforward (from the point of view of the user).

  Click on the thumbs-up Kudos to say 'Thank you' for help.

  While I strive to reflect best practices of HP, I do not work for HP.

• Device not found Airport Extreme

  We have an airport extreme connected generation via Ethernet to a switch that provides network access to our entire House (about 10-15 connections) via wifi access points all Ethernet hard wired (linksys + apple) and a direct wire to a PC. Airport extreme is the dhcp and is connected to a gpon fiber using PPPoE.

  The problem now is that the AirPort Extreme disappears from the airport on iOS Mac utility and Windows, it is found however the network and the Internet continues to operate normally on all connected devices. I can also continue ping on the router.

  I have reset the AirPort Extreme to the default settings, but the problem continued...

  I tried to unplug all devices and have AirPort Extreme only connected to him have the fiber but the problem persists...

  no idea how I can fix this problem?

  You describe a known problem with Back to My Mac which first appeared around July 13. The problem manifests itself in a message "Device not found" meant to be displayed in triangular AirPort your AirPort base station with a yellow icon utility, while the router of the device functions others continue to work normally.

  If you use an airport Time Capsule, backups will not work using that device or USB hard drive units connected to it.

  Apple will only be able to solve this problem, so all you can do is wait for them to do. If you want to contact them to tell them about it, using the contact Support link.

  There is a solution: on a Mac, open AirPort Utility and select file > configure other...

  For each of your routers Apple AirPort Base Stations serving their respective networks: its IP address and password (if you don't know either of them, read the Note that follows the horizontal rule below). Then, on the tab of the Basic Station , delete all the entries in the Back to My Mac using the 'negative' button, then click on Update.

  Which must be re-established appearance of this base station in AirPort Utility, as well as in a side bar of the Finder, if all shared disks are plugged on. It will also restore possibility of Time Machine to save on these discs, if this has also been a problem for you.

  If this seems to imply that you will not be able to use Back to My Mac until Apple fixes it, you are probably right. Well to diagnose problems of the CCMM is tedious work that I have not yet finished.

  Apple does not participate on this site except in a very limited way, so don't expect is not a response from them, here or elsewhere for that matter. We'll just have to wait for them to fix it.

• Device not found, but internet work

  I have an Airport extreme with a capsule 2 TB that I use as a backup file.

  All of a sudden I can't connect to the airport time capsule. When I launch the airport utility, there is an orange triangle/exclamation point that fits the description "device not found". The router works well, since I am connected to internet (at this time).

  I tried to unplug the unit and time capsule comes back for about 2-3 minutes until the same problem occurs again. Factory of Soft and hard resets produce the same results. I know this isn't my macbook pro because it does the same thing on my phone as well.

  You have Back to My Mac configured on the TC with your AppleID?

  This has happened to me and when I removed my AppleID and disabled Back to My Mac it ceased to occur and the TC became visible again.

  I hope that Apple will fix this soon but it would pay record a call of support with Apple on this topic as well.

• Airport Time Capsule device not found

  I have the time Capsule on the airport of the TB 3 802.11ac (bought 9/2014).  It integrates the latest version of the 7.7.7.  Just last week, I received the error device not found (.. .has been previously a part of your network... etc.).  The internet connection is always good and the component of the time capsule router still works.  When I unplug the device, it can find him but eventually will go down in a few minutes.  I also did a warm reboot, but some results.  Printer connected to the time capsule does not, nor does Time Machine back ups.

  Would be grateful of any advice on why the drive not found error continues to occur.  Thank you!

  You have Back to My Mac enabled on the Time Capsule?

  If so, turn it off for the moment in the AirPort Utility and restart the time Capsule.

• When I select print for a message preview mode, I get an error "the selected printer is not found." I can print the message, but I can't preview the output. I have

  I found that someone else has had this problem, but solution of Matt necessary use of the configuration editor. I followed the instructions, but by clicking on the Advanced tab, there was no Config Editor tab in order to execute the next step of the solution. BTW, I look in the console error log and see what: couldn't read the chrome manifest ' queue: / / / C:/Program % program % 20Thunderbird 20(x86) /Mozilla % 20Files / chrome.manifest'. The error itself is small box with Print Preview error as the label and The selected printer is not found as the contents of the box. Any help much appreciated.

  You look under Tools | Options | Advanced | General? In the main menu, which is the traditional one that spans the top of Thunderbird?