Small network VPN using ASA

I want to set up a small network of 3 offices and 1 seat. I wanted to use the cheapest and the best available solution for I came up with the following references

For head office

ASA5510-BUN-K9 ASA 5510 appliance with SW, 5FE, 3DES/AES

For Branches

ASA5505-BUN-K9 ASA 5505 appliance with SW, 10 users, 8 ports, 3DES/AES

I will configure VPN of Site which I am sure will work with this peoperly. The only thing that concerns me, what I can have 2 WAN links on each site so that I will need to set up backup link VPN from Site to Site. If a link fails in the other session VPN resumes and I'm pretty sure that this requires IP SLA. Will I get support IP SLA based this ASA 5505?

Apart from that, now, I'll order a 5505 with a 10 user license. If users in this industry grows at 15, I will be able to upgrade to ASA5505-50-BUN-K9?

Do I need an extra feature to meet my needs?


ASA5505 aura base ip sla.

10 users licenses means that:

In routed mode, hosts inside (business and home VLAN) count to the limit when they communicate with the outside (Internet, VIRTUAL local area network), including when the interior makes a connection to the outside, as well as when the outside connects to the inside. Note that even when outside initiates a connection inside, the external hosts are

not

taken into account in the limit; only inside hosts the County. Also, guests who initiates the traffic between businesses and home are not counted toward the limit. The interface associated with the default route is considered be the external Internet interface. If there is no default route, hosts on all interfaces are taken into account in the limit. In transparent mode, the interface with the smallest number of hosts is taken into account within the limits of the host. Use of the

local-host

command to show the limits of the host.

For a license 10 users, the maximum DHCP Clients is 32. For 50 users, the max.  is 128. For unlimited users, Max 250, which is the maximum for other models.

http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1491143

So you must license option for 50 or unlimited user count.

---

HTH. Please rate this post if this has been helpful. If it solves your problem, please mark this message as "right answer".

Tags: Cisco Security

Similar Questions

  • service host: local service (small network) the use of the high drive

    Hello

    I reinstalled my laptop to avoid problems. Just after you have reinstalled windows, windows automatically updated install 3 updates. After windows update, service host: local service (small network) is frequently using the high use of the disc... Microsoft, U CREATE DEFECTIVE UPDATES...

    Specifications:

    Dell Inspiron 3421

    4 GB OF RAM

    HARD DRIVE 500 GB

    Processor Intel Core i5 3317u

    In order to diagnose your problem, we need run Windows performance toolkit, the instructions that are in this wiki

    If you have any questions do not hesitate to ask

    Please run the trace when you encounter the problem
  • SSL VPN using ASA 5520 mode cluster - several problems

    I configured 2 ASA 5520 s in the load balancing cluster mode. I connect using anyconnect and I download the customer the first time and everything works well except outlook. I don't know why outlook does not work.

    The second problem is after the anyconnect client is installed on your machine, he remembers that ASA (say ASA2) he first connected and the GUI shows the address IP of ASA2 instead of the virtual IP address of the cluster. I want users always connect using the virtual IP address.

    The third problem I have is there is a default group of SSL VPN and I want all users to use this group. In the initial web page, there is a drop down menu which shows that this group, but I still want to disable this menu drop-down.

    Any suggestions?

    To disable the drop-down menu, you can turn it off with the command

    WebVPN

    no activation of tunnel-group-list

    This will take care of your last issue.

    ***************************

    You can create a profile of the Anyconnect client with the name of the server you want to connect with and that make the ASA that will solve your problem of virtual IP.

    **************************

    Regarding Outlook, do you use specific ports which allows inspection of the ASA. Take a look at the list of inspection on the SAA and perhaps try to disable inspection and see if it works.

    *****************************

  • AnyConnect for evaluating the products using ASA

    Hello people of security,.

    I am to evaluate solution Cisco Anyconnect VPN using ASA. I have a few questions must be answered as soon as possible.

    1st-

    We can combine business partners and client connections used on one ASA in a secure way?

    2nd-

    How the Anyconnect of the functions of selection of the nearest gateway (gateway optimized selection) to a user works? -J' have below link which has a very good explanation, but I'm looking for the best answer.

    (https://supportforums.cisco.com/docs/DOC-15326)

    3rd-

    Can you please highlight important features that are not taken care of other SSL providers?

    Thank you best regards &,.

    Deepak has.

    Not contexts, they cannot be used when you need VPN.

    You can set up different groups Tunnel that you assign to your different user groups. If authentication will be based on the right AAA server (if you have different servers for users and partners). It draws to award good group-policies where the rights and restrictions are configured. So, it's like the different profiles of ipsec. For AnyConnect the same tools (tunnel-groups and group-policies) are used with respect to the old VPN Client.

    --
    Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
    http://www.Kiva.org/invitedBy/karsteni

  • Remote access VPN with ASA 5510 by using the DHCP server

    Hello

    Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?

    I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:

    !

    ASA Version 8.2 (5)

    !

    interface Ethernet0/1

    nameif inside

    security-level 100

    IP 10.6.0.12 255.255.254.0

    !

    IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)

    !

    Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1

    !

    Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto-map dynamic dyn1 1jeu transform-set FirstSet

    dynamic mymap 1 dyn1 ipsec-isakmp crypto map

    mymap map crypto inside interface

    crypto ISAKMP allow inside

    crypto ISAKMP policy 1

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 43200

    !

    VPN-addr-assign aaa

    VPN-addr-assign dhcp

    !

    internal group testgroup strategy

    testgroup group policy attributes

    DHCP-network-scope 10.6.192.1

    enable IPSec-udp

    IPSec-udp-port 10000

    !

    username testlay password * encrypted

    !

    tunnel-group testgroup type remote access

    tunnel-group testgroup General attributes

    strategy-group-by default testgroup

    DHCP-server 10.6.20.3

    testgroup group tunnel ipsec-attributes

    pre-shared key *.

    !

    I got following output when I test connect to the ASA with Cisco VPN client 5.0

    Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO

    4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID

    Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID

    Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440

    Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID

    Jan 16 15:39:21 [IKEv1]: Group = testgroup, I

    [OK]

    KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload

    Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm

    Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72

    Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable

    Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

    Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64

    Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

    Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes

    Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.

    Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.

    Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!

    Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!

    Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets.  No last packet retransmit.

    Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

    Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload

    Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload

    Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets.  No last packet retransmit.

    Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address

    Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer

    Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048) , : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent

    Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740) , : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA

    Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0

    Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason

    Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

    Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE

    Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

    Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80

    Kind regards

    Lay

    For the RADIUS, you need a definition of server-aaa:

    Protocol AAA - NPS RADIUS server RADIUS

    AAA-server RADIUS NPS (inside) host 10.10.18.12

    key *.

    authentication port 1812

    accounting-port 1813

    and tell your tunnel-group for this server:

    General-attributes of VPN Tunnel-group

    Group-NPS LOCAL RADIUS authentication server

    --
    Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
    http://www.Kiva.org/invitedBy/karsteni

  • Troubleshooting IPSec Site to Site VPN between ASA and 1841

    Hi all

    in the past I've implemented several VPN connections between the devices of the SAA. So I thought a site link between an ASA site and 1841 would be easier... But it seems I was mistaken.

    I configured a VPN Site to Site, as it has been described in the Document ID: SDM 110198: IPsec Site to Site VPN between ASA/PIX and an example of IOS Router Configuration (I have not used SDM but CCP).

    I have run the wizards on the ASA with ASDM and the current IOS version 15.1 1841, with CCP.

    It seems to Phase 1 and 2 are coming although my ASA in ADSM reports (monitoring > VPN > VPN statistics > Sessions) a tunnel established with some of the Tx traffic but 0 Rx traffic),

    On the ASA:

    Output of the command: "sh crypto ipsec its peer 217.xx.yy.zz.

    address of the peers: 217.86.154.120
    Crypto map tag: VPN-OUTSIDE, seq num: 2, local addr: 62.aa.bb.cc

    access extensive list ip 192.168.37.0 outside_2_cryptomap_1 allow 255.255.255.0 172.20.2.0 255.255.255.0
    local ident (addr, mask, prot, port): (LAN-A/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (LAN-G/255.255.255.0/0/0)
    current_peer: 217.xx.yy.zz

    #pkts program: 400, #pkts encrypt: 400, #pkts digest: 400
    #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 400, comp #pkts failed: 0, #pkts Dang failed: 0
    success #frag before: 0, failures before #frag: 0, #fragments created: 0
    Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
    #send errors: 0, #recv errors: 0

    local crypto endpt. : 62.aa.bb.cc, remote Start crypto. : 217.xx.yy.zz

    Path mtu 1500, fresh ipsec generals 58, media, mtu 1500
    current outbound SPI: 39135054
    current inbound SPI: B2E9E500

    SAS of the esp on arrival:
    SPI: 0xB2E9E500 (3001672960)
    transform: esp-3des esp-sha-hmac no compression
    running parameters = {L2L, Tunnel, PFS 2 group}
    slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
    calendar of his: service life remaining (KB/s) key: (4374000/1598)
    Size IV: 8 bytes
    support for replay detection: Y
    Anti-replay bitmap:
    0x00000000 0x00000001
    outgoing esp sas:
    SPI: 0 x 39135054 (957567060)
    transform: esp-3des esp-sha-hmac no compression
    running parameters = {L2L, Tunnel, PFS 2 group}
    slot: 0, id_conn: 100327424, crypto-map: VPN-OUTSIDE
    calendar of his: service life remaining (KB/s) key: (4373976/1598)
    Size IV: 8 bytes
    support for replay detection: Y
    Anti-replay bitmap:
    0x00000000 0x00000001

    Output of the command: "sh crypto isakmp his."

    HIS active: 4
    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
    Total SA IKE: 4

    IKE Peer: 217.xx.yy.zz
    Type: L2L role: initiator
    Generate a new key: no State: MM_ACTIVE

    On the 1841

    1841 crypto isakmp #sh its
    IPv4 Crypto ISAKMP Security Association
    DST CBC conn-State id
    217.86.154.120 62.153.156.163 QM_IDLE 1002 ACTIVE

    1841 crypto ipsec #sh its

    Interface: Dialer1
    Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120

    protégé of the vrf: (none)
    local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
    current_peer 62.153.156.163 port 500
    LICENCE, flags is {origin_is_acl},
    #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
    #pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0
    #pkts not unpacked: 0, #pkts decompress failed: 0
    Errors #send 0, #recv 0 errors

    local crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
    Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
    current outbound SPI: 0xB2E9E500 (3001672960)
    PFS (Y/N): Y, Diffie-Hellman group: group2

    SAS of the esp on arrival:
    SPI: 0 x 39135054 (957567060)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel}
    Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4505068/1306)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:
    SPI: 0xB2E9E500 (3001672960)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel}
    Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4505118/1306)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    outgoing ah sas:

    outgoing CFP sas:

    Interface: virtual Network1
    Tag crypto map: SDM_CMAP_1, local addr 217.86.154.120

    protégé of the vrf: (none)
    local ident (addr, mask, prot, port): (172.20.2.0/255.255.255.0/0/0)
    Remote ident (addr, mask, prot, port): (192.168.37.0/255.255.255.0/0/0)
    current_peer 62.153.156.163 port 500
    LICENCE, flags is {origin_is_acl},
    #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
    #pkts decaps: 585, #pkts decrypt: 585, #pkts check: 585
    compressed #pkts: 0, unzipped #pkts: 0
    #pkts uncompressed: 0, #pkts compr. has failed: 0
    #pkts not unpacked: 0, #pkts decompress failed: 0
    Errors #send 0, #recv 0 errors

    local crypto endpt. : 217.86.154.120, remote Start crypto. : 62.153.156.163
    Path mtu 1452, ip mtu 1452, ip mtu BID Dialer1
    current outbound SPI: 0xB2E9E500 (3001672960)
    PFS (Y/N): Y, Diffie-Hellman group: group2

    SAS of the esp on arrival:
    SPI: 0 x 39135054 (957567060)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel}
    Conn ID: 2003, flow_id: FPGA:3, sibling_flags 80000046, card crypto: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4505068/1306)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    the arrival ah sas:

    SAS of the CFP on arrival:

    outgoing esp sas:
    SPI: 0xB2E9E500 (3001672960)
    transform: esp-3des esp-sha-hmac.
    running parameters = {Tunnel}
    Conn ID: 2004, flow_id: FPGA:4, sibling_flags 80000046, card crypto: SDM_CMAP_1
    calendar of his: service life remaining (k/s) key: (4505118/1306)
    Size IV: 8 bytes
    support for replay detection: Y
    Status: ACTIVE

    outgoing ah sas:

    outgoing CFP sas:

    It seems that the routing on the 1841 is working properly as I can tear down the tunnel and relaunch in scathing a host on the network of 1841, but not vice versa.

    Trounleshoot VPN of the 1841 report shows a message like "the following sources are forwarded through the interface card crypto.      (172.20.2.0 1) go to "Configure-> routing" and correct the routing table.

    I have not found an error on the 1841 config so if one of the guys reading this thread has an idea I appreciate highly suspicion!

    It's the running of the 1841 configuration

    !
    version 15.1
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    encryption password service
    !
    host name 1841
    !
    boot-start-marker
    start the system flash c1841-adventerprisek9 - mz.151 - 1.T.bin
    boot-end-marker
    !
    logging buffered 51200 notifications
    !
    AAA new-model
    !
    !
    AAA authentication login default local
    !
    AAA - the id of the joint session
    !
    iomem 20 memory size
    clock timezone PCTime 1
    PCTime of summer time clock day March 30, 2003 02:00 October 26, 2003 03:00
    dot11 syslog
    IP source-route
    !
    No dhcp use connected vrf ip
    !
    IP cef
    no ip bootp Server
    IP domain name test
    name of the IP-server 194.25.2.129
    name of the IP-server 194.25.2.130
    name of the IP-server 194.25.2.131
    name of the IP-server 194.25.2.132
    name of the IP-server 194.25.2.133
    No ipv6 cef
    !
    Authenticated MultiLink bundle-name Panel
    !
    !
    object-group network phone
    VoIP phone description
    Home 172.20.2.50
    Home 172.20.2.51
    !
    redundancy
    !
    !
    controller LAN 0/0/0
    atm mode
    Annex symmetrical shdsl DSL-mode B
    !
    !
    crypto ISAKMP policy 1
    BA 3des
    preshared authentication
    Group 2
    isakmp encryption key * address 62.aa.bb.cc
    !
    !
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    !
    map SDM_CMAP_1 1 ipsec-isakmp crypto
    Description Tunnel to62.aa.bb.cc
    the value of 62.aa.bb.cc peer
    game of transformation-ESP-3DES-SHA
    PFS group2 Set
    match address 100
    !
    !
    !
    interface FastEthernet0/0
    DMZ description $ FW_OUTSIDE$
    10.10.10.254 IP address 255.255.255.0
    IP nat inside
    IP virtual-reassembly
    automatic duplex
    automatic speed
    !
    interface FastEthernet0/1
    Description $ETH - LAN$ $FW_INSIDE$
    IP 172.20.2.254 255.255.255.0
    IP access-group 100 to
    IP nat inside
    IP virtual-reassembly
    IP tcp adjust-mss 1412
    automatic duplex
    automatic speed
    !
    ATM0/0/0 interface
    no ip address
    No atm ilmi-keepalive
    !
    point-to-point interface ATM0/0/0.1
    PVC 1/32
    PPPoE-client dial-pool-number 1
    !
    !
    interface Dialer1
    Description $FW_OUTSIDE$
    the negotiated IP address
    IP mtu 1452
    NAT outside IP
    IP virtual-reassembly
    encapsulation ppp
    Dialer pool 1
    Dialer-Group 2
    PPP authentication chap callin pap
    PPP chap hostname xxxxxxx
    PPP chap password 7 xxxxxxx8
    PPP pap sent-name of user password xxxxxxx xxxxxxx 7
    map SDM_CMAP_1 crypto
    !
    IP forward-Protocol ND
    IP http server
    local IP http authentication
    IP http secure server
    !
    !
    The dns server IP
    IP nat inside source static tcp 10.10.10.1 808 interface Dialer1 80
    IP nat inside source static tcp 10.10.10.1 25 25 Dialer1 interface
    IP nat inside source overload map route SDM_RMAP_1 interface Dialer1
    IP nat inside source overload map route SDM_RMAP_2 interface Dialer1
    IP route 0.0.0.0 0.0.0.0 Dialer1 permanent
    !
    logging trap notifications
    Note category of access list 1 = 2 CCP_ACL
    access-list 1 permit 172.20.2.0 0.0.0.255
    Note access-list category 2 CCP_ACL = 2
    access-list 2 allow 10.10.10.0 0.0.0.255
    Note access-list 100 category CCP_ACL = 4
    Note access-list 100 IPSec rule
    access-list 100 permit ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
    Note CCP_ACL the access list 101 = 2 category
    Note access-list 101 IPSec rule
    access-list 101 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
    access-list 101 permit ip 172.20.2.0 0.0.0.255 any
    Note access-list 102 CCP_ACL category = 2
    Note access-list 102 IPSec rule
    access-list 102 deny ip 172.20.2.0 0.0.0.255 192.168.37.0 0.0.0.255
    access-list 102 permit ip 10.10.10.0 0.0.0.255 any
    !

    !
    allowed SDM_RMAP_1 1 route map
    corresponds to the IP 101
    !
    allowed SDM_RMAP_2 1 route map
    corresponds to the IP 102
    !
    !
    control plan
    !
    !
    Line con 0
    line to 0
    line vty 0 4
    length 0
    transport input telnet ssh
    !
    Scheduler allocate 20000 1000
    NTP-Calendar Update
    NTP 172.20.2.250 Server prefer
    end

    As I mentioned previously: suspicion is much appreciated!

    Best regards

    Joerg

    Joerg,

    ASA receives not all VPN packages because IOS does not send anything.

    Try to send packets to the 1841 LAN to LAN of the ASA and see is the "sh cry ips its" on the 1841 increments the encrypted packets (there not)

    The problem seems so on the side of the router.

    I think that is a routing problem, but you only have one default gateway (no other channels on the router).

    The ACL 100 is set to encrypt the traffic between the two subnets.

    It seems that the ACL 101 is also bypassing NAT for VPN traffic.

    Follow these steps:

    Try running traffic of LAN router inside IP (source of ping 192.168.37.x 172.20.2.254) and see if the packages are not through the translation and obtaining encrypted.

    I would also like to delete 100 ACL from the inside interface on the router because it is used for the VPN. You can create an another ACL to apply to the interface.

    Federico.

  • VPN on ASA 5506 without internet access, help with NAT?

    Hello

    I have upgraded to a Cisco ASA 5505 to a 5506 X and as such have climbed to ASA 9.5

    For this reason, I'm a bit stuck on how to implement the VPN. I followed the wizard and I can now establish inbound connections, but when connected (all traffic is tunnel) there is no internet connectivity.

    Our offices internal (inside) network is 192.168.2.0/24

    Our VPN pool is 192.168.4.0/24

    I guess that I'm missing a NAT rule, but in all honesty, I'm a user ASDM and as everything is changed, I am struggling to recreate it?

    Here is my config:

    Result of the command: "sh run"
    
    : Saved
    
    :
    : Serial Number: JAD194306H5
    : Hardware:   ASA5506, 4096 MB RAM, CPU Atom C2000 series 1250 MHz, 1 CPU (4 cores)
    :
    ASA Version 9.5(1)
    !
    hostname ciscoasanew
    domain-name work.internal
    enable password ... encrypted
    names
    ip local pool RemoteVPNPool 192.168.4.1-192.168.4.254 mask 255.255.255.0
    !
    interface GigabitEthernet1/1
     nameif outside
     security-level 0
     ip address 192.168.3.4 255.255.255.0
    !
    interface GigabitEthernet1/2
     nameif inside
     security-level 100
     ip address 192.168.2.197 255.255.255.0
    !
    interface GigabitEthernet1/3
     shutdown
     no nameif
     no security-level
     no ip address
    !
    interface GigabitEthernet1/4
     shutdown
     no nameif
     no security-level
     no ip address
    !
    interface GigabitEthernet1/5
     shutdown
     no nameif
     no security-level
     no ip address
    !
    interface GigabitEthernet1/6
     shutdown
     no nameif
     no security-level
     no ip address
    !
    interface GigabitEthernet1/7
     shutdown
     no nameif
     no security-level
     no ip address
    !
    interface GigabitEthernet1/8
     shutdown
     no nameif
     no security-level
     no ip address
    !
    interface Management1/1
     management-only
     nameif management
     security-level 100
     ip address 192.168.1.1 255.255.255.0
    !
    ftp mode passive
    clock timezone GMT 0
    dns domain-lookup inside
    dns domain-lookup management
    dns server-group DefaultDNS
     name-server 192.168.2.199
     domain-name work.internal
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    object network obj_any
     subnet 0.0.0.0 0.0.0.0
    object network 173.0.82.0
     host 173.0.82.0
    object network 173.0.82.1
     subnet 66.211.0.0 255.255.255.0
    object network 216.113.0.0
     subnet 216.113.0.0 255.255.255.0
    object network 64.4.0.0
     subnet 64.4.0.0 255.255.255.0
    object network 66.135.0.0
     subnet 66.135.0.0 255.255.255.0
    object network a
     host 192.168.7.7
    object network devweb
     host 192.168.2.205
    object network DevwebSSH
     host 192.168.2.205
    object network DEV-WEB-SSH
     host 192.168.2.205
    object network DEVWEB-SSH
     host 192.168.2.205
    object network vpn-network
     subnet 192.168.4.0 255.255.255.0
    object network NETWORK_OBJ_192.168.4.0_24
     subnet 192.168.4.0 255.255.255.0
    object network NETWORK_OBJ_192.168.2.0_24
     subnet 192.168.2.0 255.255.255.0
    object-group network EC2ExternalIPs
     network-object host 52.18.73.220
     network-object host 54.154.134.173
     network-object host 54.194.224.47
     network-object host 54.194.224.48
     network-object host 54.76.189.66
     network-object host 54.76.5.79
    object-group network PayPal
     network-object object 173.0.82.0
     network-object object 173.0.82.1
     network-object object 216.113.0.0
     network-object object 64.4.0.0
     network-object object 66.135.0.0
    object-group service DM_INLINE_SERVICE_1
     service-object icmp
     service-object icmp6
     service-object icmp alternate-address
     service-object icmp conversion-error
     service-object icmp echo
     service-object icmp information-reply
     service-object icmp information-request
    access-list outside_access_in extended permit tcp object-group EC2ExternalIPs object DEVWEB-SSH eq ssh
    access-list outside_access_in remark AWS Servers
    access-list outside_access_in extended permit tcp object-group EC2ExternalIPs object devweb eq ssh log debugging inactive
    access-list outside_access_in extended permit ip any any inactive
    access-list outside_access_in remark Ping reply
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any interface outside
    access-list outside_access_in remark Alarm
    access-list outside_access_in extended permit tcp any interface outside eq 10001
    access-list outside_access_in remark CCTV
    access-list outside_access_in extended permit tcp any interface outside eq 7443
    access-list outside_access_in extended deny ip any any
    access-list workvpn_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
    access-list workvpn_splitTunnelAcl_1 standard permit 162.13.130.12 255.255.255.252
    access-list workvpn_splitTunnelAcl_1 standard permit 162.13.133.72 255.255.255.252
    access-list workvpn_splitTunnelAcl_1 standard permit 164.177.128.200 255.255.255.252
    access-list workvpn_splitTunnelAcl_1 standard permit 164.177.132.16 255.255.255.252
    access-list workvpn_splitTunnelAcl_1 standard permit 164.177.132.72 255.255.255.252
    access-list workvpn_splitTunnelAcl_1 standard permit 212.64.147.184 255.255.255.248
    access-list workvpn_splitTunnelAcl_1 standard permit 95.138.147.116 255.255.255.254
    access-list workvpn_splitTunnelAcl_1 standard permit 95.138.147.118 255.255.255.254
    access-list workvpn_splitTunnelAcl_1 standard permit host 95.138.147.118
    access-list workvpn_splitTunnelAcl_1 standard permit 95.138.147.120 255.255.255.254
    access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 192.168.4.0 255.255.255.0
    access-list workvpn2_splitTunnelAcl standard permit 192.168.2.0 255.255.255.0
    access-list workVPN2016_splitTunnelAcl standard permit 192.168.2.0 255.255.255.0
    pager lines 24
    logging enable
    logging buffer-size 16000
    logging asdm-buffer-size 512
    logging asdm warnings
    logging flash-bufferwrap
    mtu outside 1500
    mtu inside 1500
    mtu management 1500
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 7200
    no arp permit-nonconnected
    nat (inside,outside) source static NETWORK_OBJ_192.168.2.0_24 NETWORK_OBJ_192.168.2.0_24 destination static NETWORK_OBJ_192.168.4.0_24 NETWORK_OBJ_192.168.4.0_24 no-proxy-arp route-lookup
    !
    object network obj_any
     nat (any,outside) dynamic interface
    object network DEVWEB-SSH
     nat (inside,outside) static interface service tcp ssh ssh
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 192.168.3.3 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    user-identity default-domain LOCAL
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    http 192.168.2.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    service sw-reset-button
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec security-association pmtu-aging infinite
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto ca trustpoint _SmartCallHome_ServerCA
     no validation-usage
     crl configure
    crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
     enrollment self
     fqdn none
     subject-name CN=192.168.2.197,CN=ciscoasanew
     keypair ASDM_LAUNCHER
     crl configure
    
    snip
    
    dhcpd auto_config outside
    !
    dhcpd address 192.168.1.2-192.168.1.254 management
    dhcpd enable management
    !
    no threat-detection basic-threat
    threat-detection statistics port
    threat-detection statistics protocol
    threat-detection statistics access-list
    threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
    ssl trust-point ASDM_Launcher_Access_TrustPoint_0 inside
    ssl trust-point ASDM_Launcher_Access_TrustPoint_0 inside vpnlb-ip
    group-policy DfltGrpPolicy attributes
     vpn-tunnel-protocol ssl-client
    group-policy workVPN2016 internal
    group-policy workVPN2016 attributes
     dns-server value 192.168.2.199
     vpn-tunnel-protocol ikev1
     split-tunnel-policy tunnelall
     ipv6-split-tunnel-policy tunnelall
     default-domain value work.internal
     split-dns value work.internal
     split-tunnel-all-dns enable
    dynamic-access-policy-record DfltAccessPolicy
    
    !
    class-map inspection_default
     match default-inspection-traffic
    !
    !
    policy-map type inspect dns preset_dns_map
     parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
     class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
    !
    service-policy global_policy global
    prompt hostname context
    call-home reporting anonymous
    hpm topN enable
    Cryptochecksum:
    : end
    

    Hi Ben-

    What you are trying to accomplish is called VPN crossed.  Depending on your initial configuration, you have 2 NAT problems.  The first has to do with the NAT you place your order.  In the code later that we are dealing with two NAT ASA 8.3 times and who are ranked 2 sections going on before and after the device NAT. object

    My general rule for control of NAT is like this:

    1. Twice NAT (front) - use this section for exemptions from NAT or unusual configurations that have to go first
    2. Purpose of NAT - Use this section to the static NAT instructions for servers
    3. Twice NAT (after) - use this section to your global declarations of NAT, basically a catch-all

    Then, never use 'all' as an interface for all training of NAT.  This may seem like a good idea, but it will bite you.  Remember, it is more the notion of control NAT, then 'all' interface is bit VPN configurations and similar DMZ.  Always be specific about your interface for NAT pairs.

    To this end, here is what I suggest that your NAT configuration should resemble:

    nat (inside,outside) source static NETWORK_OBJ_192.168.2.0_24 NETWORK_OBJ_192.168.2.0_24 destination static NETWORK_OBJ_192.168.4.0_24 NETWORK_OBJ_192.168.4.0_24 no-proxy-arp route-lookup!object network DEVWEB-SSH nat (inside,outside) static interface service tcp ssh ssh !nat (inside,outside) after-auto source dynamic any interfacenat (outside,outside) after-auto source dynamic any interface
    The key is that you need a NAT device explicitly reflecting the VPN traffic. PSC
  • Problem with IPsec VPN between ASA and router Cisco - ping is not response

    Hello

    I don't know because the IPsec VPN does not work. This is my setup (IPsec VPN between ASA and R2):

    my network topology data:

    LAN 1 connect ASA - 1 (inside the LAN)

    PC - 10.0.1.3 255.255.255.0 10.0.1.1

    ASA - GigabitEthernet 1: 10.0.1.1 255.255.255.0

    -----------------------------------------------------------------

    ASA - 1 Connect (LAN outide) R1

    ASA - GigabitEthernet 0: 172.30.1.2 255.255.255.252

    R1 - FastEthernet 0/0: 172.30.1.1 255.255.255.252

    ---------------------------------------------------------------------

    R1 R2 to connect

    R1 - FastEthernet 0/1: 172.30.2.1 255.255.255.252

    R2 - FastEthernet 0/1: 172.30.2.2 255.255.255.252

    R2 for lan connection 2

    --------------------------------------------------------------------

    R2 to connect LAN2

    R2 - FastEthernet 0/0: 10.0.2.1 255.255.255.0

    PC - 10.0.2.3 255.255.255.0 10.0.2.1

    ASA configuration:

    1 GigabitEthernet interface
    nameif inside
    security-level 100
    IP 10.0.1.1 255.255.255.0
    no downtime
    interface GigabitEthernet 0
    nameif outside
    security-level 0
    IP 172.30.1.2 255.255.255.252
    no downtime
    Route outside 0.0.0.0 0.0.0.0 172.30.1.1

    ------------------------------------------------------------

    access-list scope LAN1 to LAN2 ip 10.0.1.0 allow 255.255.255.0 10.0.2.0 255.255.255.0
    object obj LAN
    subnet 10.0.1.0 255.255.255.0
    object obj remote network
    10.0.2.0 subnet 255.255.255.0
    NAT (inside, outside) 1 static source obj-local obj-local destination obj-remote control remote obj non-proxy-arp static

    -----------------------------------------------------------
    IKEv1 crypto policy 10
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 3600
    Crypto ikev1 allow outside
    crypto isakmp identity address

    ------------------------------------------------------------
    tunnel-group 172.30.2.2 type ipsec-l2l
    tunnel-group 172.30.2.2 ipsec-attributes
    IKEv1 pre-shared-key cisco123
    Crypto ipsec transform-set esp-aes-192 ASA1TS, esp-sha-hmac ikev1

    -------------------------------------------------------------
    card crypto ASA1VPN 10 is the LAN1 to LAN2 address
    card crypto ASA1VPN 10 set peer 172.30.2.2
    card crypto ASA1VPN 10 set transform-set ASA1TS ikev1
    card crypto ASA1VPN set 10 security-association life seconds 3600
    ASA1VPN interface card crypto outside

    R2 configuration:

    interface fastEthernet 0/0
    IP 10.0.2.1 255.255.255.0
    no downtime
    interface fastEthernet 0/1
    IP 172.30.2.2 255.255.255.252
    no downtime

    -----------------------------------------------------

    router RIP
    version 2
    Network 10.0.2.0
    network 172.30.2.0

    ------------------------------------------------------
    access-list 102 permit ahp 172.30.1.2 host 172.30.2.2
    access-list 102 permit esp 172.30.1.2 host 172.30.2.2
    access-list 102 permit udp host 172.30.1.2 host 172.30.2.2 eq isakmp
    interface fastEthernet 0/1
    IP access-group 102 to

    ------------------------------------------------------
    crypto ISAKMP policy 110
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 42300

    ------------------------------------------------------
    ISAKMP crypto key cisco123 address 172.30.1.2

    -----------------------------------------------------
    Crypto ipsec transform-set esp - aes 128 R2TS

    ------------------------------------------------------

    access-list 101 permit tcp 10.0.2.0 0.0.0.255 10.0.1.0 0.0.0.255

    ------------------------------------------------------

    R2VPN 10 ipsec-isakmp crypto map
    match address 101
    defined by peer 172.30.1.2
    PFS Group1 Set
    R2TS transformation game
    86400 seconds, life of security association set
    interface fastEthernet 0/1
    card crypto R2VPN

    I don't know what the problem

    Thank you

    If the RIP is not absolutely necessary for you, try adding the default route to R2:

    IP route 0.0.0.0 0.0.0.0 172.16.2.1

    If you want to use RIP much, add permissions ACL 102:

    access-list 102 permit udp any any eq 520

  • Routing issue of Cisco VPN Client ASA

    Hi, I use a Barracuda NG for firewalls and I would use a Cisco ASA 5505 for VPN Client connections. But I have the problem that I can't get a connection to the VPN PC connected to the internal network. But I can reach the VPN connected PC from the inside. Here is a diagram of my network:

    Here the IP Configuration and the routing of the Barracuda firewall table:

    I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

    The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

    Here is the config Cisco ASA:

     : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

    Can someone please help me solve this problem?

    When I tried to solve this I didn't choose which interface the Packet Tracer?

    The interface inside or DMZ interface?  Inside, he says it will not work with the dmz but the error did not help me

    Anyone here knows why it does not work?

    Hello

    Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

    entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

    Route by tunnel watch also with 255 administrative distance.  I've never used that in my scenarios... lets see...

    Concerning

    Knockaert

  • CME SSL VPN with ASA

    Hi all

    We are working on a new deployment of CME 9.1 for a small office. As part of this deployment, our plan was to have several remote phones connect via SSLVPN to an ASA on our network border allowing them to communicate with the router of the CME. We bought the appropriate of the VPN to ASA and licenses of paper for phones remotely.

    I'm following the instructions in this document: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configura...

    However, the penalty, I'm having is that when I try to enter the settings for vpn-Group (page 19 of the pdf) the command is not available on my router - unrecognized command. I fear that this could mean that I'm missing a license/feature set to my router CME, is that correct? We bought a C2921CME-SRSTK9 router, but I may need the SEC/K9 license? If this is the case, can someone show me the part number or SKU, I would need to buy?

    Moreover, is anyway that I could get around to adding this to the router config - perhaps change the configuration of phone XML directly?

    Thanks in advance!

    It is correct, you will need the license of security. SKU is: L-SL-29-SEC-K9 =

    http://www.Cisco.com/c/en/us/products/collateral/routers/1900-series-int...

  • IPSec vpn cisco asa and acs 5.1

    We have configured authentication ipsec vpn cisco asa acs 5.1:

    Here is the config in cisco vpn 5580:

    standard access list acltest allow 10.10.30.0 255.255.255.0

    RADIUS protocol AAA-server Gserver

    AAA-server host 10.1.8.10 Gserver (inside)

    Cisco key

    AAA-server host 10.1.8.11 Gserver (inside)

    Cisco key

    internal group gpTest strategy

    gpTest group policy attributes

    Protocol-tunnel-VPN IPSec

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list acltest

    type tunnel-group test remote access

    tunnel-group test general attributes

    address localpool pool

    Group Policy - by default-gpTest

    authentication-server-group LOCAL Gserver

    authorization-server-group Gserver

    accounting-server-group Gserver

    IPSec-attributes of tunnel-group test

    pre-shared-key cisco123

    GBA, we config user group: VPN users. all VPN users in this group. ACS can visit his political profile: If the user in the 'VPN users' group, access ACS.

    When we connect from a VPN Client to the server, all users connect to success. When you see the parser in ACS journal, each user success connect also get

    error:

    22040 wrong password or invalid shared secret

    (pls see picture to attach it)

    the system still works, but I don't know why, we get the error log.

    Thanks for any help you can provide!

    Duyen

    Hello Duyen,

    I think I've narrowed the issue. When remote access VPN using RADIUS authentication we must keep in mind that authentication and authorization are included on the same package.

    Depending on your configuration, the ACS is defined as a server RADIUS (Gserver Protocol radius aaa server) and becomes the VPN Tunnel authenticated and 'authorized' on this server group:

    authentication-server-group LOCAL Gserver

    authorization-server-group Gserver

    As noted above, the RADIUS of request/response includes authentication and authorization on the same package. This seems to be a problem of incorrect configuration that we should not set up the 'permission' in the Tunnel of the group.

    Please remove the authorization under the Tunnel of Group:

    No authorization-server-group Gserver

    Please test the connection again and check the logs of the ACS. At this point there are only sucessful newspaper reported on the side of the ACS.

    Is 'Permission-server-group' LDAP permission when authenticating to a LDAP server so to retrieve the attributes of permission on the server. RAY doesn't have the command as explained above.

    I hope this helps.

    Kind regards.

  • Impossible to establish a VPN to ASA 5505

    I'm trying to set up a network VPN from Site to Site. Right now I'm doing this work in the laboratory. I have the Internet port on the Linksys connected directly to port 0 on the cisco that has been set up as the internet port.

    My configuration is:

    Remote site

    Laptop 1 - IP 192.168.2.100 address 255.255.255.0 GW 192.168.2.1

    The Router 1 (Linksys BEFSX41) - LAN IP 192.168.2.1 255.255.255.0

    209.168.145.49 WAN IP address 255.255.255.0 GW 209.168.145.50

    Host site

    Laptop 2 - address 192.168.1.100 IP 255.255.255.0 GW 192.168.1.1

    Router 2 (Cisco ASA 5505) - LAN IP 0 address 192.168.1.1 255.255.255.0

    IP WAN (Port 0) 209.168.145.50 255.255.255.0

    My problems:

    I use ASDM 5.2 to configure the router of the SAA. With the configuration I currently have my linksys is not able to establish a VPN connection. The journal of ASA reported via the ASDM is as shown in the attachment ciscolog.txt.

    My linksys journal is as listed in the attachment linksyslog.txt.

    I also tried to create a Cisco VPN client connection using the cisco client software and a laptop connected directly to the internet port of the router cisco (port 0) and was not able to establish a connection with that either. I used the wizard of ASDM VPN to try to implement the Site-site as well as the scenarios of connection remotely. This has been unsuccessful in both cases.

    The only one, I am really interested in getting to work is the site to site.

    My current configuration of cisco is shown in the attachment cisco.txt.

    If anyone has any input I would appreciate it a lot. I have been through the manuals of cisco as to scouring the internet and am unable to find an answer.

    I enclose 3 files, cisco log (ciscolog.txt), linksys (linksyslog.txt) log and config cisco (cisco.txt) in the form of text files.

    Thank you.

    Sean

    I hope that path statement solves your problem.

    -Gilbert

    Good job, Adam!

  • Physical networks VPN multiple interfaces of the ATA.

    Hello all and thanks in advance for any advice you can provide.

    I have a 5220 ASA set up with 3 networks. I have a off-grid, one inside the network and a network of "DSL". Everything works great, except that I'm trying to clean up the way we connect with VPN client.

    At the moment, if we are outside our network, we use the external IP address of the router (x.x.A.1). When we are on the LAN subnet, we are unable to VPN to the external IP address, so we are forced to use a completely separate identification information together and to connect to the IP address of the subnet LAN (x.x.B.1).

    Is it possible to configure the VPN so that we would be able to use the same credentials to connect to the interface either? I can use DNS selective so that requests are sent to the correct IP address... but as it is, it does not accept one set of credentials on each interface.

    Any help would be appreciated.

    Question:

    Have you tried to set up a separate crypto for the LAN interface card input.

    Lets say you have an entry like this crypto map...

    Crypto-map dynamic dynmap 65534 transform-set RIGHT

    cry map outside_map 65536-isakmp ipsec dynamic dynmap

    interface card cry out outside_map

    Can you try to create another entry card crypto under a different name for the LAN interface.

    Let me know.

    See you soon

    Gilbert

  • Order of operations NAT on Site to Site VPN Cisco ASA

    Hello

    I have a question about the order of operations NAT on Site to Site VPN Cisco ASA 8.2.x. I have a scenario where the internal IP address of the range 10.17.128.x are NATTED IP public 31.10.10.x. below is the config:

    Tunnel normally passes traffic to dmz - 31.10.11.10, 31.10.11.11 servers.

    But the servers NATTED (10.17.128.x <->31.10.10.x) does not work.

    inside_map crypto 50 card value transform-set ESP-3DES-SHA

    tunnel-group 100.1.1.1 type ipsec-l2l

    tunnel-group 100.1.1.1 General-attributes

    Group Policy - by default-PHX_HK

    IPSec-attributes tunnel-group 100.1.1.1

    pre-shared key *.

    internal PHX_HK group policy

    PHX_HK group policy attributes

    VPN-filter no

    Protocol-tunnel-VPN IPSec svc webvpn

    card crypto inside_map 50 match address outside_cryptomap_50

    peer set card crypto inside_map 50 100.1.1.1

    inside_map crypto 50 card value transform-set ESP-3DES-SHA

    inside_map crypto 50 card value reverse-road

    the PHX_Local object-group network

    host of the object-Network 31.10.11.10

    host of the object-Network 31.10.11.11

    host of the object-Network 31.10.10.10

    host of the object-Network 31.10.10.11

    host of the object-Network 31.10.10.12

    host of the object-Network 31.10.10.13

    host of the object-Network 10.17.128.20

    host of the object-Network 10.17.128.21

    host of the object-Network 10.17.128.22

    host of the object-Network 10.17.128.23

    the HK_Remote object-group network

    host of the object-Network 102.1.1.10

    inside_nat0_outbound list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

    ACL_INSIDE list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

    ACL_OUTSIDE list extended access permitted ip object-group HK_Remote-group of objects PHX_Local

    outside_cryptomap_50 list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

    Route outside 102.1.1.10 255.255.255.255 30.1.1.1 1

    public static 31.10.10.10 (Interior, exterior) 10.17.128.20 netmask 255.255.255.255

    public static 31.10.10.11 (Interior, exterior) 10.17.128.21 netmask 255.255.255.255

    public static 31.10.10.12 (Interior, exterior) 10.17.128.22 netmask 255.255.255.255

    public static 31.10.10.13 (Interior, exterior) 10.17.128.23 netmask 255.255.255.255

    He started to work when I did another group of object by name PHX_Local1 and added to the list of access inside_nat0_outbound, instead of the object group PHX_Local, as below:

    the PHX_Local1 object-group network

    host of the object-Network 31.10.10.10

    host of the object-Network 31.10.10.11

    host of the object-Network 31.10.10.12

    host of the object-Network 31.10.10.13

    No inside_nat0_outbound access list extended only to allowed ip object-group PHX_Local-group of objects HK_Remote

    inside_nat0_outbound list extended access permitted ip object-group PHX_Local1-group of objects HK_Remote

    Can you please help me understand why group object PHX_Local failed with access-list inside_nat0_outbound, but he began to work with the Group of objects PHX_Local1.

    Also, if you could tell me the order of operations to NAT via VPN Site to Site, it would be useful.

    Thank you

    Kind regards

    Thomas

    Hello

    I think you could have said the original question in a way that could be missleading. In other words, if I understand now.

    From what I understand now, you have the DMZ set up the server that are measured with a public IP address on the real servers. And for those that you have configured NAT0.

    Then you have other servers that do not have public IP addresses themselves, but they are translated on the SAA.

    If this is the case, then the next question would be. The server with the NAT should attend the L2L VPN connection with their real IP or address IP NAT.

    Of course if you configure static NAT for the same servers and NAT0 the NAT0 will always win.

    You have these guests who were not able to use the VPN L2L

    31.10.10.10 10.17.128.20

    31.10.10.11 10.17.128.21

    31.10.10.12 10.17.128.22

    31.10.10.13 10.17.128.23

    IF you want them to go to the VPN L2L with their original IP address then you must configure

    object-group, LAN

    host of the object-Network 10.17.128.20

    host of the object-Network 10.17.128.21

    host of the object-Network 10.17.128.22

    host of the object-Network 10.17.128.23

    object-group, REMOTE network

    host of the object-Network 102.1.1.10

    inside_nat0_outbound list extended access allowed ip-group of objects LOCAL object-group remote

    outside_cryptomap_50 list extended access allowed ip-group of objects LOCAL object-group remote

    IF you want to use the L2L VPN with the public IP address, then you must configure

    object-group, LAN

    host of the object-Network 31.10.10.10

    host of the object-Network 31.10.10.11

    host of the object-Network 31.10.10.12

    host of the object-Network 31.10.10.13

    object-group, REMOTE network

    host of the object-Network 102.1.1.10

    outside_cryptomap_50 list extended access allowed ip-group of objects LOCAL object-group remote

    EDIT: in this case you naturally do not configure any NAT0 for actual IP addresses we want precisely the IP addresses to be visible to the L2L VPN with the IP NAT address.

    Or you can of course use the same "object-group" as currently but change the content in an appropriate manner

    Be sure to mark it as answered if it was answered.

    Ask more if necessary

    -Jouni

  • Does anyone know why my iMac G5 osx10.5.8 suddenly developed continuous small networks of lines on the screen please? I can provide screenshots.

    Does anyone know why my iMac G5 osx10.5.8 suddenly developed continuous small networks of lines on the screen please?

    I tried to provide screenshots - insert an image does not accept.

    Just happened while the iMac was asleep.

    Thanks in advance

    Tony

    The image seems to reflect the possibility of problems of graphics processor.

    Some models had a history of failure or bad solder connections. others may

    have a combination of capacitors & other materials; Finally we have to fix.

    https://DuckDuckGo.com/?q=imac + 24 - anomalies graphics + 2008 + in +& t = ffsb

    One of the remedies for a graphics card problem, is a re - weld made by the

    users who have taken their card from the computer & their cooked in the kitchen oven.

    This idea has worked for some; You may be able to contact an authorized Apple

    Service provider or see if any of the parts suppliers in line can answer questions

    availability of replacement given to nine graphics cards, if you were

    can be removed from the logic board or if it is affixed, or welded to the card.

    An iFixit.com repair guide for your series of iMac (Intel-processor 2008) 24 inches

    can show that if that article can be virtually eliminated, if if will show process.

    https://www.iFixit.com/device/iMac_Intel_24%22

    The details of the computer in the bottom of your post isn't an iMac G5 model, and

    There is no powerPC G5 processor equipped Macs after late vintage

    2005 to early 2006; If the computer in the discussion is a G5 is not 24 inches

    and would be a model of Intel. They use a different architecture than G5

    powerPC even though in some respects are similar at least in the General design.

    This contains all guide ifixit for iMac G5 Power repair (there is no 24-inch model)

    https://www.iFixit.com/device/iMac_G5

    If you have an iMac with Intel processor and an older iMac PowerPC G5, specify.

    Don't know if a reset of the SMC or likely to alter the symptoms or change NVRAM

    the Visual problem on the screen; an underlying hardware problem is a likely cause.

    • Reset the management system (SCM) controller on your Mac - Apple Support

    • How to reset the NVRAM on your Mac - Apple Support

    If this is your model iMac (24 inch Early 2008) follows the model of generation identifier:

    Introduced April 2008

    Abandoned March 2009

    IMac8, 1 model identifier

    Model number A1225

    EMC 2211

    MB325LL/A order number

    First Prize $1 799 (2.8 GHz) $2 199 (3.06 GHz)

    You may be able to find the numbers of reference and research for replacement new or repaired

    old stock graphics cards. A friend had one of these models of iMac 24 inch 2008 and

    It failed due to a graphic processor; where she lived the BestBuy did not fix

    She even if it has been purchased by them with their extended warranty; No applecare.

    So, there are some out there in almost perfect condition, but not fixed, always.

    Do not know if the charges involved would be the value relative to the other

    later construction that can have no history of similar design construction. {Confirm the identity of the iMac.}

    Sorry I don't have any new ideas regarding this problem.

Maybe you are looking for

  • paper loads of pages, then freezes

    all of a sudden, my copy of pages does not load a document that I worked before I use the pages.  It opens then the spinning wheel is displayed and I have no other alternative but to force exit pages.  Does not happen when I send it to my version of

  • Satellite 1900-803: how to install a USB 2.0 port?

    How to install a USB Port of 2.00Where can I get a?Need for the new IpodAnyone out there it does or can help please?

  • DeskJet 3050 J610 series: printer removes items in the print queue

    Printer refuses to print despite printing and Scan Doctor saying it's very good.  Document appears very briefly in the print queue, and then disappears.  Printer has been reinstalled from the installation and the old version of the printer disc remov

  • SSL VPN on IOS but no traffic

    Dear score I configured SSL VPN on c3845. WebVPN working via browser but through webvpn client I am able to connect but can not reach an internal with ip address on the network. Please find the show for your reference

  • Can I create multiple webistes with Muse?

    I have the unique Adobe Muse app membership. Can I use this to create more than one Web site?