Smartwizard discovered on machine with two IP addresses.

Similar Questions

• VMware device with 2 network cards claiming the same IP address with two MAC addresses

  Hello.

  I see messages intermittent my gateway network two MAC addresses associated with a virtual machine running on a 5.5 ESXi host for the same IP address.

  The virtual machine is a MiTel 3300 controller for a VOIP system. the system is configured with two IP addresses, one on the local network and another with a public IP address in the DMZ. In the network configuration of the 3300, I assigned the address LAN IP at 00: 0C: 29:30:B2:B2 and the DMZ IP at 00: 0C: 29:30:B2:BC (Mac for network devices presented by the ESXi host virtual machine).

  On the host, I configured a vSwitch with exclusive access to two physical network adapters on the host machine. The vSwitch is configured with two machine virtual port groups, LAN and DMZ, with access to the physical network interface cards. Tab grouping of groups vSwitch port NIC, I replaced the order of failover of the switch to activate an active NETWORK card only for the Group of LAN ports and the other card NETWORK only for the DMZ port group. (I don't know how the content of the column of networks is determined. Neither is correct for the traffic on the physical switch. If these are configurable, please advise and I'll change the settings). The relevant parameters of vSwitch, groups of ports and VM are distinguished below.

  On the virtual machine itself, through the VMWare host, I assigned 00: 0C: 29:30:B2:B2 for the Group of LAN ports and 00: 0C: 29:30:B2:BC to the DMZ group port (best I can tell, anyway, since the MAC address field annoyingly obscures the last two digits of the MAC address - break if I invert the mapping) (, but all seems OK).

  The goal here is to make sure that MACs of ports vSwitch the 3300 is listening and sending always correspond to the physical ports that are VLAN Tag by the physical switch to ensure the routing. Generally speaking, it seems that what is happening but, intermittently, we cross one-way calls that suggests a problem of routing between us and our SIP trunk provider; coinciding with these incidents, I get an email along the lines of "the security in the network device has detected a conflict of IP address with two or more devices. The period of INVESTIGATION "DMZ. DMZ. DMZ. DMZ' is claimed by the following clients with MAC addresses: ' 00: 0C: 29:30:B2:B2' ' 00: 0C: 29:30:B2:BC'. »

  I did something in the configuration that would lead to this kind of collision intermittent? Have a hacked together a way to do something that could be accomplished in a way that is simpler and more reliable?

  Thanks for any idea that you can offer.

  Kind regards

  J.

  

  

  

  I probably don't fully understand your configuration, but it seems that you are not interested in using the collection of NETWORK adapters in the virtual switch of the VM MiTel 3300.

  If it is correct, why not create two virtual switches, each with a group of port (LAN and DMZ) unique and with a separate connection of (vmnic2 and vmnic1)?

  In general, collection of NETWORK adapters may be used to share traffic between uplinks and ensure that if one of the uplinks connect fails, a virtual machine still has access to the network.

• How to create a new virtual machine with two warehouses of data through new-vm?

  Hi guys,.

  Can you please help or direct me to the right format? I'm new with vsphere powercli.

  How to create a virtual machine with two other data store by using the new-vm?

  $datastore1 = get-datastore. WHERE-object {$_.} Name - eq "lun1"}

  $datastore2 = get-datastore. WHERE-object {$_.} Name - eq "lun2"}

  new-vm-name vmtest01 - VMHost ESXserver - datastore $datastore1 diskmb - 8192 $datastore2 diskmb - 8192 - memorymb 4096 - numcpu 2 - ID winNetStandardGuest

  I got this error when I run vsphere powercli. I appreciate if you can help. Thank you

  New-VM: cannot bind parameter 'DiskMB '. Cannot convert the 'lun2"val

  EU to type 'VMware.VimAutomation.ViCore.Impl.V1.DatastoreManagement.DatastoreIm '.

  PL"type"System.Int64 ".

  At line: 1 char: 85

  + new-vm-name vmtest01 - VMHost ESXserver - $datastore1 data store

  diskmb - < < < < 8192, $datastore2 - diskmb 8192

  + CategoryInfo: InvalidArgument: ( , ParameterBindingE)

  Xception

  + FullyQualifiedErrorId: CannotConvertArgumentNoMessage, VMware.VimAutomat

  ion.ViCore.Cmdlets.Commands.NewVM

  Bryan

  The New-VM cmdlet takes a single value of the parameter - data store and all of the virtual disks will be located on this data store.

  If I understand your request, you create a virtual machine with 2 virtual disks, each on a different data store.

  You can use the cmdlet New - hard drive for it.

  $datastore1 = get-datastore | where-object {$_.Name -eq "lun1"}
  $datastore2 = get-datastore | where-object {$_.Name -eq "lun2"}
  
  $vm = new-vm -name vmtest01 -VMHost ESXserver -datastore $datastore1 -diskmb 8192 -memorymb 4096 -numcpu 2 -GuestId winNetStandardGuest
  new-harddisk -vm $vm -datastore $datastore2 CapacityKB (8192 * 1KB)
  

  ____________

  Blog: LucD notes

  Twitter: lucd22

• AYahoo (business) account with two email addresses stopped working properly on Firefox a few days ago. OK in other browsers, Firefox ok on other accesoriess.

  Worked fine until a few days ago. We have an account of Yahoo business, with two addresses. Normally, we can see only an e-mail account to the time, and to change the points of view, there is a drop-down list box top left of Yahoo mail which normally allows the selection of the desired account. Now in these last days, by selecting the drop-down list box only will take you to the Yahoo profile update page, not the drop down menu which allows us to change the e-mail account, we want to see. Correct operation is noted in IE9, but neither Firefox 32-bit or 64-bit allows you to select the second email address.

  try to read Web sites look bad or display differently they should

• vCell Setup with two IP addresses and routing

  Hello

  My networking team suggested the following configuration:

  VLAN-Public: first card network load balancing

  VLAN-squatting: second nic load balancer

  VLAN-front: first and second nic vCloud Cell01 and even for vCloud Cell02

  VLAN-Back: vCenter / ESXi / vShieldMgr / SQL / etc.

  Traffic / routing between VLAN-front and back - VLANS are possible.

  Now, I installed vCell01 with two network cards, each one IP address: 192.168.1.1 and 192.168.1.11.

  vCell02 with two network cards, each one IP address: 192.168.1.2 and 192.168.1.12.

  Installation was no problem, connect to SQL went smooth.

  But then I noticed that I could not reach 192.168.1.11 since the vCenter Server. Which makes sense, now that I think of it, given that traffic from the vCenter for 192.168.1.11 lights eth1, but due to the default gateway will leave on eth0. And vCenter probably won't like that.

  My questions:

  -Can I solve this through routing changes to the routing of the vCells table?

  -Should I do a complete change in my configuration / network design?

  -Should I continue and do not worry vCenter being unable to reach 192.168.1.11.

  Advice welcome

  PS: Using CentOS 6.5

  Concerning

  Gabrié

  I ran into a similar problem with asymmetric routing when I first set up my vCloud multi-homed cells.  In my case, the IP address for each interface was on a different subnet, but the approach is the same for your scenario.  You must add that some policy based routing using iproute2 commands rules.

  Here's a great article that describes the problem and the solution: http://www.linuxjournal.com/article/7291

  For your question, you probably want something like this:

  Cell01:

  / sbin/IP flush table 1 road

  / sbin/IP flush table 2 road

  / sbin/IP route add default via dev eth0 table 1

  / sbin/IP route add default via dev eth1 table 2

  / sbin/IP rule add from 192.168.1.1/32 table priority 1 500

  / sbin/IP rule add the priority of 192.168.1.11/32 table 2 600

  Cell02:

  / sbin/IP flush table 1 road

  / sbin/IP flush table 2 road

  / sbin/IP route add default via dev eth0 table 1

  / sbin/IP route add default via dev eth1 table 2

  / sbin/IP rule add from 192.168.1.2/32 table priority 1 500

  / sbin/IP rule add the priority of 192.168.1.12/32 table 2 600

  Good luck!

• Migration of a virtual machine with two RDM physical to a newly created VMFS Datastore 5.0

  Dear all,

  I'm redrawing the storage storing all the VM, I have a machine virtual with two physical RDM to 2 TB each, with only 800 consumed Go, the question is can I svMotion to the new 2.5 to data store? the virtual machine (40 GB VMDK, RDM TB 2 * 2)

  Thank you.

  
  Djak44

  Hello

  Is there a particular reason that you must keep the RDM devices? Personally, I would keep away using the RDM disks because they can cause massive headaches.

  If you go with again in RDM as described already sure to go virtual in order to have the added capacity for RDM

  Gregg

• ACS with two IP address?

  Hello

  We have the CSACS-1121-K9 Cisco ACS 5.4 running chassis, the chassis has four interfaces and I was wondering if I can configure two different ip addresses in different segments to authenticate network devices. This, because we have to manage two different networks.

  Thank you.

  I use SNS3495 ACS 5.5, and I already have,

  I had 3 interface (1 management MMIC, 1 ACS (gui and ssh), 1 officer of AAA services management)

  I think this would work on your case.

  but we could have only 1 Management (for GUI config and SSH) interface

  don't forget to add the static route between networks.

• I need help, how to configure virtual machines with PowerCLI IP addresses

  Hi all

  I open this topic because I really need your help.

  I wrote a script that can automatically create 10 VMs on my ESX Server.

  I run the script with PowerCLI.

  I want now to help script, give the ip on the 10 machines created settings.

  I don't know how, can you enlighten me on this subject?

  Is there a script that can do this?

  Thank you very much.

  Isn't the "0.2 | ForEach-Object {"a loop for? IMHO, it is a loop in the PowerShell way.

• How can synchronize 2 direct vms with different ip address

  Hello

  I have a question I have 2 virtual machines, their data are exactly even now I want to know is there any wany to synchronize their data?

  I don't want to use VR because vr can't the VMS syn 2 which turn on it just can make a sgadow of the one on the host of othe

  now I want to have 2 virtual machines with different ip address, and in time, they can synchronize data

  Best regards

  Babak

  There are no methods that can be used that will do what you are trying the hypervisor layer.  It will be done in the comments.  I would recommend for your machines two windows RoboCopy, and for your two Linux guests recommend Rsync.,.

  There is not much more that we can really say here, that you excluded the VMware replication as your need to have different IP addresses in the two guests.

• URGENT! Two physical network with two subnets completely - no bridges - interface cannot connect both

  This is my urgent problem:

  I have a physical machine with two physical network interfaces. I have a VMWARE player and a virtual machine that must use cards on two different subnets, a public directly to the router and an intranet within the company.

  How can I just say a net card to go on this submarine and the other on the public void?  Go crazy. Help, please.

  Thank you

  P.

  Use the virtual network editor VMware Player, create an additional bridged VMnet and bind each bridged to a different physical network... card VMnet on a virtual machine, create a virtual network adapter on each subnet and bind each virtual network adapter to an another VMnet jumpered.

  For additional help with virtual network Editor, check this KB: VMware KB: using the VMware Workstation virtual network editor

• List of virtual machines with static IP

  VMware gurus,

  I'm trying to generate a list of virtual machines that are configured with static IP address.

  IPPolicy: static

  I need a script that returns the name of the virtual machine that has static to IPpolicy.

  Jadapa RHCE, MCSA

  http://linuxgurus.WordPress.com

  You can create a list of virtual machines with static IP addresses with the following script PowerCLI:

  Get-VM | `
    Get-VMGuestNetworkInterface -GuestUser User -GuestPassword Password -HostUser User -HostPassword Password | `
    Select-Object -property VM,IPPolicy | `
    Where-Object {$_.IPPolicy -eq "Static"}
  

  Best regards, Robert

• text messages sent with an email address from a touch ipod duplicated on a second ipod touch using a different email address, but the two ipods are controlled by a parent with the same apple ID and password.

  Text messages sent with an email address from a touch ipod duplicated on a second ipod touch using a different email address, but the two ipods are controlled by a parent with the same apple ID and password.  This has happened recently.  My two girls have used their respective ipods and texting, without their messages of duplication for each of the other ipods for more than a year.  Somehow recently, both addresses seem to be synced with them or something, so that both see each and other messages.  I've recently updated two ipods, iTunes on my computer--not the cloud and added music for two ipods, but has not changed anything by email email settings or message I know.  Help, please!

  Welcome to the Apple community.

  I can't fully follow how you have everything set up, but a glance at the settings > messages > send & receive

• Can I run outlook and outlook Express on the same computer with two different e-mail addresses?

  My e-mail with outlook express and my wife with outlook email address.

  Yes. You can run them with the same email address as well.

• Incredible trouble with two A10 S203 network!

  I had two Satellite A10-S203. This mobile are configured to operate on Microsoft network (wired network) with the working group. Have a different IP, name, MAC addresses, and same workgroup. To the network to work about 15 computers. When I connect to the network from one of them his works very well with the network. If I replace the previous book to second it's job well too. But when I connect both at the same time to the network I got hurt. One work, second cannot send pockets but can receive them. When this two laptops are connected to some other network computers sometimes hangs up.
  This portable work very well no but together do not work in the same network.
  I checked the configuration of these hundreds of times and it's ok they can see and browse the net when are linked separately. Thought is it net card MAC addresses conflict but it isn t.
  Can someone help me with this?

  Post edited by: TomaszE

  You are quite right TomaszE, very cryptic your problem!

  But what is the subnet mask of the network? Also identical on all machines?
  Have you tried to change the IPS of the two laptop, just intended to test?
  All are machine have static ip addresses, or runs a dhcp server in the system?
  What about firewalls installed? Some programs have a blacklist of ip addresses that are blocked permanently to do anything on the network.

  Please give me more information

  BR

• Impossible to connect a network drive by name of host but able to match with the ip address

  is the act as an application server and the file server. We use it as normal, but it is suddenly unable to resolve host name for other machines.

  All servers and workstations are not able to map the drive network under with the name of host, but every server and workstation still able to map the network drive with the IP address.

  When we try to connect the network drive with the host name, it invites with the error shows that there is error authorizcation.

  We tried and discover a few points as below for your reference:

  • Able to ping and resolve the hostname via all other servers and workstations.
  • Able to access the Terminal Server service name
  • Able to network with the IP address drive
  • Power of the card itself with the host name

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/categories/