SNMP v3

Similar Questions

• What necessary SNMP MIB file

  Does anyone know where I could find information (MIB) machine for Toshiba MFP devices file. I googled had and checked the predominant sites for these types of files. I'm looking to get the OID for an eStudio-600 so I can configure the SNMP interruptions for alerts of toner and paper jams.

  Thank you

  Mike

  PS: I put here as a matter of SNMP network, if it's wrong please feel free to move it to the right forum.

  In my opinion, this forum is wrong place for this question. I think you should contact your local dealer where you bought your eStudio-600.
  They offer a type of support or not?

• Is it possible to configure SNMP or logging remotely on the R8000?

  The stock firmware allows logging of external data?

  As a way secret for the program to install/activate SNMP?

  Or direct the output of logging to an external server?

  Because the viewport of the newspapers little pointless, just doesn't really cut it and go through the journal by email whenever you want to look over is simply absurd.

  There is no support SNMP, for one of the Netgear router machine, in stock firmware.

• ReadyNAS Ultra 6 SNMP addon

  Hi all

  I had to reset my ReadyNAS Ultra 6 by default and have lost the SNMP addon. I can't locate on my own PC, or on one of the forums. I searched for hours without success. Anyone out there have the .bin still available and power poster file or email it to me please?

  Thanks in advance.

  Hello mdshelton123,

  Stephen is right, we saw the link you gave, but you already have updated the firmware of the OS6.

  I asked the subject to be moved archives available in the community. It's here: https://community.netgear.com/t5/Community-Add-ons/SNMPon-0-1-1/td-p/789452

  Kind regards

• StorCenter px6 - 300 d SNMP SNMP problem after FW update to 4.0.2.9960

  Hello

  We have a problem in PX6 - 300 d, after the upgrade from version 3.2.3.15290 to 4.0.2.9960, FW SNMP configuration. Ishmael of application allows us to manage matrices. After updating the FW one of storage, the application can no longer collect information. Notify know if there was no change of FW which caused this problem?

  SNMP parameters in storage, are equal, the difference in this version of the FW of storage.

  Thank you for your help

  Adias

  Hi adias.

  There is a newer version of the firmware. I recommend updating to the latest version to see if the problem persists.

  Firmware Version 4.0.8.23976 for px6 - 300 d

• SNMP help please?

  Hello

  I'm all new to SNMP, although I have used LabVIEW a few times in recent years. Office supplies for the moment, I am developing an application to test the power. We use a G756N Dell PDU for each switching power. I tried a couple of approaches to control and SNMP is the most promising so far. During my research I came across free ManageEngine MibBrowser and I could find the last MIB to download the firmware from Dell here. I was able to communicate with the UDA and points of sale under and out so far, but I really need to integrate control of the PDU in the application of LabVIEW to automate tests. I'm pinned Mark Yedinak and his APC PDU SNMP communication library, only the most recent of which I found examples in this thread.

  I tried to do a VI to test communication in LabVIEW using the OID I received from MibBrowser, but it returns an error code 2, noSuchName. The PDU is configured to use SNMP v1 and the public and private communities write access +. I tried with and without the main point, but without success. I'm using LabVIEW 2013 64-bit. Could someone please review the information below and see what I could do wrong, or that the direction to take to solve the problems there?

  Thank you

  Simon

  MIB object IDS:

  . iso.org.dod.internet.private.enterprises.dell.pdu.pdusub.hardware.rPDU.rPDUOutlet.rPDUOutletSwitched.rPDUOutletSwitchedControlTable.rPDUOutletSwitchedControlEntry.rPDUOutletSwitchedControlCmd

  . 1.3.6.1.4.1.674.10903.200.2.200.130.1.4.1.4.1: {1 or 2}

  I added le.1 at the end of the index to the first exit, and 1 variable is instantaneous, while the 2 is instant off

  Photo

  

  VI:

  Front panel:

  

  Wiring:

  

  Link to examples of SNMP Communications and APC_PDU.zip:

  http://forums.NI.com/T5/LabVIEW/APC-ups-with-desktop/m-p/2431528/highlight/true#M749059

  For some reason, I can't the real VI set. The MIB is too in the archive. Its in my selection here:

  https://DL.dropboxusercontent.com/u/10871313/power%20Supply%20Testing.zip

  Thanks again

  
  

• Help with SNMP

  I found an online library of SNMP vi that someone writes and I fight so he can work. I think I use them properly because I can get some OID to work
  and others do not return anything.

  OID.1.3.6.1.2.1.1.1.0 - works fine. It returns the same OID, the data type, then the value.
  OID.1.3.6.1.4.1.21796.4.1.3.1.4.1 - does not work, it returns a different OID and nothing to the value or the type of data.

  Anyone used this library before?  All I have to do is get a value from a device. Any ideas?

  The original poster has contacted me directly, and I gave an updated version of the library which has solved its problems. To be honest I don't know what the updates are in the latest version of the library from the version he got was old enough. In any case, here's the latest version for someone else who may need SNMP.

• MSM765 Team: port source MSMS765 team of SNMP

  Hi all

  We have a team of controllers MSM765. We use the ports of controllers in the following ways:

  • Internet port: only for the management
  • LAN port: use for production, the traffic of users

  Our network management tool (SNMP querys, etc.) is in the network of EHF Internet port of the team. The team sends traps SNMP with LAN Port as a source. We do not want to open any type of comunicarion between the 'Network management' and 'network of Production '.

  It is possible to change the source port the SNMP Traps generated by the team of the LAN Port to the Internet port?.

  Best regards.

  Hello

  My problem must be linked with the routing, as my default route points to a gateway in my LAN Port. I can solve it by adding static routes for networks explicits (hosting the SNMP servers) pointing to the gateway on the Internet Port.

  Best regards.

• JetAdmin SNMP v3 credentials lost

  Hi, I recently inherited an instance of JetAdmin. My problem is that I do not know the SNMPv3 and password encryption used to put in place my cameras. I am able to change the password via the web interface of each individual printer but I know, if using JetAdmin, SNMP v3 has been installed, change the password on the web interface does not work.

  The credentials are saved in the store of credentials, but I have no idea how to access. Any ideas on what are my options?

  I can't change the password through JetAdmin because it requires current credentials first.

  TLDR: Took over JetAdmin, need to reset SNMPv3 name of user and password for use with monitoring tools further

  I work for HP, but my messages and responses are mine. .....

  Sorry for the multiple responses SergZ...  Most of the JetDirect products do not allow the use of sentence the EWS interface.  Do newer, but I don't have details on the firmwares & models.  For this reason, it is impossible to synchronize a device w / global of WJA credentials store found under Tools, Options.  My last message well enough to start from scratch.  For this reason and another...

  When HOSTS detects a device via V3, it assumes that a part of the management going in V3.  So, I gave you a few steps:

  -go to the EWS device and completely disable the v3 (may want to clear the fields of credentials as part of this action, I'm not sure...)

  -either run a discovery in HOSTS that re-capture this device w / no V3 enabled (you can also do selection refresh (full), but you must wait for a polling cycle to get the data device recaputred HOSTS, there is no good indication when that happens)

  -HOSTS allows to set the new credentials and enable V3

  -the identification of the document information!

  I think that you will have success if you follow this path.  Let me know, thanks!

  BikeRider

• Problems whit a LLB for snmp

  Dear Sir

  I saw a couple toppics old off topic this LLB.  LLB, I use

  See attachment, OID mine don't get not translated the rightway.

  The problem is that the OID mine has a number of 30 bits, 852179988, RRS04v30.  Who is separated into two, a b11, then the rest of the number.

  But how I do not know to solve it. If someoneelse has a better LAW degree for communication SNMP knows a solution to the problem of landmines,

  Thank you

  Already solved it, the patch is developed SNMP Encoder SubID.vi entry into OID.vi to build SNMP on U64.

  Then again this OID obtained the rightway translated:

  . 1.3.6.1.4.1.7829.1.852177940.322961408.1.1.3.0

  Hope this is help for someone else

• On a windows 2003 R2 SP2, gives error 1053 SNMP service startup

  On a windows 2003 R2 SP2, start the service SNMP gives error 1053 (below)

  

  In the event log are event ID: 7000 & 7009 back (below)

  

  

  Already tried: https://support.microsoft.com/en-us/kb/886695 (check the "allow service to interact with desktop").

  I have also run the Windows updates for all high priority updates, replaced the files %windir%\system32\snmp*.* with those of another R2 SP2 server that is not the problem (after rename the original to the *.old files & copy the same files in the folder DLLcache so SFC would stop interfering ;)) and checked for other errors that may show a reason for this - the only thing that I can connect to it) , it is that services IISAdmin & GoogleUpdate (gupdate & gupdatem) having the same problem, but unrelated to seams...

  TNX in advance for any response.

  Kobi

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Using SNMP to number of requests by fax

  I wish I could use SNMP to query and track the number of pages of the fax on my CM4540 printers.

  Can someone tell me if this is possible and if so, what MIB and OID would be used.

  Thank you

  Brian

  This morning, I got my response from HP.  Here's what I learned.

  For access to archive printer MIB:

  1. go to http://h20147.www2.hp.com/sppmain/

  2. click on the link Public of Software Development Kits (SDK)

  3. Select Laserjet and Digital Sender of the Kit Area drop-down box

  4. navigate to LaserJet and Digital Sender > management of printers > printer specific MIB

  5. sort the list of Legacy printers, then select the appropriate model

  6. wait for the browser to refresh, and then click the download button

  7. save the file on your machine and review

  I tried saving and opening a without extension, seems that it is just a text file.  It looks like some are .zip.  Some are registered as .mib trying to open it in a CMD window on my machine.  None of the files I was looking at was a text for SNMP OID objects.  Perhaps you need to translate the information into an OID somehow.

  Take a look and let me know if you can make progress more or not.  Its been fun to discover all that we have learned so far.

• Problem for the SNMP or WMI on my forehead TMG

  I tried to make the system of monitoring on all services. our company have to the sites. We made a plan to set WMI protocols on all microsoft services and it works well, except on the TMG. I have provided the SNMP and WMI both two of them rejected. so I checked 135 for its opening SNMP port number and port of WMI too but they cannot establish a connection. I'd appreciate if you help me to solve this problem.

  Concerning

  Hello

  Sorry for the late reply.

  That your computer is under domain, you must contact the TechNet forum, where we have of the support technicians who are well equipped with the knowledge on the issues of domain, do visit the link provided below.

  http://social.technet.Microsoft.com/forums/en-us/winserverfiles/threads

• Agent Extension SNMP event log has not initialized properly in windows 2008 R2

  I enabled the functionality of SNMP Service and found the following error:

  "Error 2019: Extension SNMP event log Agent has not initialized properly in windows 2008 R2 Enterprise 64-bit.

  I uninstalled all related SNMP Applications and reinstalled the functionality of the SNMP Service, however, I always do face the same error.

  According to the following of Article http://support.microsoft.com/kb/128729 , this requires to contact microsoft to obtain the fix.

  I have a subscription with Microsoft technical support to download the fix mentioned the article above.

  Any help please,.

  Hello

  The question you posted would be better suited in the community pro Windows 2008.
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Can someone tell me which makes snmp service send a trap event. I mean, snmp does not monitor anything. To send a trap, a person or an application request SNMP to do. Which?

  I was doing some research on SNMP and MIBs.Hit a roadblock when this question came to my mind. Windows stores all MIBs under

  %SystemRoot%\System32

  I know that these MIBs are used to send traps. I just want to know the throughput, or how it's done. Who reads all this information and provides it to the snmp service to send a trap event? If I need to send traps that are defined in some other MIBs, how can I do it?

  Any help will be appreciated. :)

  Hello

  The question you posted would be better in the Technet forum. Check out the link and ask the question.

  http://social.technet.Microsoft.com/forums/en-us/winserver8gen/threads

• Index of physical memory SNMP oid has changed after system reboot

  I asked for a hot - difficulty for windows 2003 server. Server must be restarted after you apply the hotfix to hot. After the reboot, I noticed this index of oid snmp for physical RAM increased from 17 to 16. is this normal behavior for snmp to change the Index oid?

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the Windows Server Forums on TechNet. Please post your question in the Windows Server Forums.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/