Software FPGA with LabVIEW 2013

Similar Questions

• A UDP connection target FPGA with LabVIEW

  Hello

  I have an FPGA with Ethernet connected to my HOST PC, now I would like to connect the LabVIEW FPGA target and access to its records. Please suggest me.

  Kind regards

  Chetan

  Hi Cheetah,.

  don't know, because I do not know your format or the manual of your FPGA...

• cDAQ works correctly with Labview 2013?

  I have already upgraded to the LV805 for Labview 2013 in an existing system that has the cDaq-9172, NI9205, NI9263, and NI 9403.

  When executing NI MAX, it detects that cDAQ 9172 (chassis), but none of the cDAQ modules are detected.

  When I open my application, the paths of the cDAQ doesn't appear in entry options, so when it works, and the error message.

  I have SP1 2013 LV f2 and NEITHER-DAQmx 9.8

  This is a known issue, or I have a configuration problem?

  Help, please

  EDGAR_PLATRONICS wrote:

  Now, I have another problem.

  When I turn on my PC cDAQ does not start automatically.

  I have to go to services Windows and manually start OR Setup manager. Same startup is set to Automatic

  Once I run it, cDAQ works correctly.

  My company uses McAffe antivirus

  Concerning

  Edgar

  Mine also.  (McAffe)

  It turns out than if you change the startup type to "Automatic (delayed services start)" service OR McAffe plays more enjoyable.

  

• How the interface telnet or PuTTY or plink software Windows with LabVIEW

  Please find the screenshot attached screen of the problem that face here.

  He is, can't open the telnet session by using the IP address of the DEVICE. But after that am not able to send commands or argument to the PuTTY or plink.

  Exec System does not accept standard input.

  In the plink.exe screenshot began operating only after sending to put manually... and after getting invited ">" if I send the command 'SEND' to plink.exe he answers returns with the data of the unit.

  Here I am not able to automate this send command Enter and SEND to get the data of the unit.

  He will be grateful if someone give me a solution.

  Thank you

  Vijay

  I solved this with Telnet VI by adding \r\n for all orders that we send to the unit.

  Pls find the attached final VI in LabVIEW 8.6

  Concerning

  Vijay

• Editing software created with labview

  Hello

  I have a software that was created using labview. It is essentially a software to control a laser machine used for the deposit of material. I also I have the source code of the software. I want to make some modifications to the program. When I do some changes in the source code. I see that there is no change in the software that is an exe file. so, how can I solve this problem? I guess that once I have the changes to the source code, I need to create a new executable from the VI. So I want to know how can I do a new screw exe file has changed.

  I want to know what is the difference between the following

  .VI file

  file .llb

  file .lvllb

  Thanks in advance

  Vikas

  Hello

  I could solve my problem using the executable command generate in the Tools menu.

  Thank you

• Installation of the Module LabVIEW 2012 SP1 FPGA with LabVIEW 2012 SP1 64 bit on Windows 7 X 64 machine.

  I installed 32-bit and 64-bit LabVIEW 2012 SP1 on Windows 7 X 64 computer. After that, I installed SP1 FPGA Module. While module FPGA completely installed in the 32-bit version and could develop projects fpga, FPGA interface has not installed the 64-bit version. Anyone had this before question?

  The document 5WMF8NQ2 knowledge base says it's doable.

  I have tried to repair the installed module, remove and then reinstall the module. Nothing helped me to get the FPGA interface on a 64-bit host VI. Any suggestions? Addition of the individual screws through the range of editing functions like a tedious process and the palette is not completely functional.

  I solved the problem. Had to repair each driver separately for LabVIEW 2012 SP1 64 bit installed on the default drive. You may need to copy paste files to the folder that it installed in function.

• Problem control pumps syringe with LabVIEW 2013

  Hi all

  I try to use a program that was sent to me by a coworker to control 2 pumps to KD scientific syringe using LabVIEW.  The pumps are connected to a Windows 7 computer via a telephone line attached to the pump, which is then connected to an RJ11 to D - type RS-232 converter.  A Hawking Technology RS-232 to USB converter cable connects this converter to a USB port on the computer (this is because our computer has only 1 serial port but we have 2 syringe pumps).  It's the same establishment that has been using my collaborator and it worked without any problem.

  The problem arises when we try to control pumps syringe with the LabVIEW program.  We have drivers for Hawking and KD scientific syringe pumps cables installed on the computer, but our computer recognizes that the cable is plugged in - it does not recognize the syringe pushes like a 'peripheral '.  We can run the LabVIEW program, but essentially, nothing happens.  When we press "stop"button, we get an error message that says: "error 1073807202 occurred when opening VISA in Science KD 2XX series Initializes vi."  In my view, this means that the computer/LabVIEW is not able to communicate with the pumps, even if we have installed the drivers and in the same folder as the program.

  I enclose the program we are trying to run (it's Version 2, it includes the drivers for syringe pumps), the pilot shot of the error message, we installed the cable, as well as a screen.  If anyone knows anything we can try would be much appreciated.  The author of the program has been at a loss because it works wonders on his computer.

  Thank you in advance!

  Laura

  Indeed, I am convinced that the pumps are connected to the correct COM ports.  So I just thought of something... I noticed on the website OR that there are drivers for NI-VISA.  I know for a fact that I have not installed on this particular computer.  Does make sense that these missing drivers could be the problem?  That would explain the error to the opened VISA.  I do not have the administrator rights for this computer so I have to wait for an admin to connect and install the drivers.  I'll give you an update with what's happening.  Thank you all!

• problems with labview 2013 build specification

  I have a few screws of LV2010 I want to use to create an application to run with RTE2013. I have LV2013 on my computer.

  Without a massive compilation of the LV2010 screws, the element of selection of source files in the build specification has no project file to choose and it won't allow me to go looking for.

  Any ideas why this happens?

  Thank you

  Right, you must create a project and put in all of the screws to be included in the compilation - including one that is the top-level VI. Once this is done, you can save the project, just not to re-record the EIS.

  Now you should be able to define your spec to build according to normal.

  Mike...

• How to down load and use OpenStreetMap offline with LabVIEW 2013

  Dear all

  How can I download the OpenStreetMap database and API for LabVIEW call this map offline database!

  Thank you

  Luong.Tran

  Thank you!

• HELP - FPGA SPARTAN 3E-100 CP132 WORKS WITH LABVIEW FPGA?

  HI EVERYONE, GET ON IM TRYING TO USE MY FPGA WITH LABVIEW, BUT I DO KNOW THAT IF ITS COMPATIBLE, I INSTALLED THE DRIVERS, MODULE FPGA AND LABVIEW 2012, IM USING WINDOWS 7 32 BIT, AND AFTER I COMPILED ITS SAYS:

  LabVIEW FPGA called another software component, and the component returned the following error:

  Error code:-310601

  NOR-COBS: Impossible to detect the communication cable.
  Check the communication cable is plugged into your computer and your target. Also, verify that the proper drivers are installed.

  Thank you.

  =)

  Hi dvaldez2.

  LabVIEW FPGA offers no support for any material to third parties, other than the 3rd Spartan XUP Starter Kit. These are probably the drivers you downloaded.

  http://digital.NI.com/express.nsf/bycode/Spartan3E?OpenDocument&lang=en&node=seminar_US

  However, this driver supports only the Starter Kit Board itself (http://www.digilentinc.com/Products/Detail.cfm?NavPath=2, 400, 790 & Prod = S3EBOARD). You may not use the driver with any other Xilinx FPGAS.

  I hope this helps.

• Problems with the implementation of 32 or 64-bit DLLs in LabView 2013 13.0f2

  Dear Sirs and Madams,

  I try to order a motorized device (MGZ30-WORD thorlabs) with LabView 2013 (32 bit), product version 13.0f2 on a PC under Windows 7 64-bit. Unfortunately, there is no support of LabView for the WORD MGZ30, which means that there are no libraries or VIs for LabView.

  First of all, I want to describe the component or rather its functionality. It is connected to the PC via USB and managed by the v5.0.2153.1 Trinamic Virtual Serial Port Driver. If you wish, for example, adjust the position of the device, there is a small program (written in C++ by the seller). There are 2 different folders for 32 and 64-bit, each containing a .exe, .dll two (a ThemeControl.dll called, who apparently does not have the feature described in the h.file, I want to talk about later, and a ThorZStepper.dll called), a .lib (ThorZStepper.lib) file and an .xml file (ZStepeprSettings.xml, which contains the used COM Port and baud rate information). In addition, there is a folder that contains the driver and a folder called "SDK", that contains the subfolder with a .h file, samples and once more the files mentioned before.

  To use your device, you must modify the COM - ID in the .xml file and run the 64-bit .exe as administrator.

  First of all, I tried to use the VISA-USB-controls, which worked well with another device. However, he did not for the WORD MGZ30 as I did not have the possibility of obtaining the necessary chains of command although I used a sniffer port. Observed communication seems to be more complex than I expected and I was unable to extract the relevant information. To add, the device seems to communicate constantly with the PC even if it is inactive.

  The next idea, which came to my mind was to put in place the .dll files. Therefore, I used the import via Tools/Import/SharedLibrary function and the only h-file that I found in the file and the dll file which stood next the .exe in the folder of 64 bit. LabView created a file .lvlib and I got access to a few screws, which have also been described in the header file. The problem is that I can't run these screws because the .dll file is 64-bit while LabView is only 32-bit (at least, LabView suggests that this is the error.

  After that, I tried the same thing using the same header file (there is only one), but using the .dll file located in the folder of 32 bits. When I now try to run the files, execution of works, but I get an error message "call library function Node in ThorZStepper32.lvlib:Find Devices.vi. There are also a few screws, which do not generate this error, but will not work.

  My next test was to use the "call library function Node", as well as documentation in the .h file, but it didn't work. I don't know if I missed something or the 32-bit .dll file does not work on 64-bit operating system. Could you please help me to use the "call library function node" to investigate the weather that the 32-bit dll does not work properly?

  Please find the file h., (html.zip) documentation of the h.file and the VI, it must indicate the position, attached.

  Best wishes and thanks in advance!

  
  

• Camera not found, error 1074360311 occurred at IMAQdx Open Camera.vi, USB cameras labview 2013 64 (bitts)

  I use USB cameras with labview 2013, and I can acquire images in the MAX and in the Acquisition of mink (express) settings, but when I run the VI, always appear the same error as shown in the Image below.

  -J' checked the correct versions of my software, IMAQ, IMAQdx, VDM 2013 IMAQ of e/s

  -J' I also make sure I had all the updated device drivers.

  -I'm using IMAQdx LKD schema and examples, getting the same error uu

  Help, please!

  Any suggestions would be very helpful.

  

  If it works in the pop up app Express VI and inside MAX (the two 32-bit applications), then I guess it will work in 32-bit LabVIEW. We wonder why it does not work in 64-bit LabVIEW, but these are the drivers of the device and other pieces of infrastructure/DirectShow Windows.

• LabVIEW 2013 executable only works on the development machine?

  Hi all

  I created an executable to distribute my test software, but it only works on the development computer. With success, I gave my front executables with labview 2012 on the target computers by simply creating the .exe in the project and then Explorer in installing labview nessary drivers and run the engine of time without problems. Now, I created a new test with Labview 2013 program and I can not get my new test .exe application to run on the target computer. Has anyone seen this kind of problem before?  Any help will be appreciated.

  Thank you

  
  

• 7953 FPGA with 6581 adapter world clock inputs

  I am very new to FPGA with LabVIEW design. I have a FPGA 7953 card that connects to the 6581 adapter. This brochure, looking the 6581.

  ( http://www.ni.com/pdf/products/us/cat_ni6581.pdf )

  on page 3, it says "Note: clock is connected to the world clock for the NI FlexRIO FPGA module entries. I think it means that DDCA, 67 of the 6581 pin, I can feed an external clock in which is accessible in my LabVIEW FPGA code to entries world clock of the 7953? I don't know what these entries world clock would be on the 7953. It would be one of the choices presented to me as shown in the attached picture?

  Sorry if this question is wacky...

  Hi JHaas,

  I think that I can't fully responding to your question.  Yes, you can introduce an external clock in the 6581, which is accessible in your FPGA code.  Take a look at this knowledge base article which has some more details on the pins to use, and how to use the clock in a timed cycle loop.

• IMAQ PCI-1424 compatibility with Labview 8.6

  Hi, the computer that I used for image analysis had a broken motherboard issue, and I replaced it with a new one. I removed both the drives and the jury from the old computer to the new and then installed IMAQ Labview 8.6, but Labview 8.6 is not compatible with the software programmed with labview 5.0, so I uninstalled Labview 8.6 and re-installed Labview 6.0 image processing. I still have some problems to run the Analyzer software and image processing. After you have uninstalled the software or labview, the computer does not start correctly, poping up error as information "check your hard drive to ensure that it is properly configured and completed. Run CHKDSK /F to check for hard drive corruption, and then restart your computer."

  Some basic information on this computer and the image acquisition system (introduced in 2000) are as follows:

  • Windows 2000 operating system;
  • LabVIEW 5.0 basic package;
  • IMAQ vision for Labview advanced;
  • IMAQ PCI-1408, Cables IMAQ-BNC-1 and or-IMAQ for Windows NT / 95;
  • IMAQ-A2504-1 (1 m).
  • Sony XC - 55 1/3 "Interline transfer progressive scan CCD, 659 (H) X 494 (V), C-mount with JB - 77, SERVICES-12 p-02 and DKT503M;
  • Computar H1212FI 1/2 "mount C 12 mm w/focus and iris (10 inches FOV at 24 work dist.);
  • Extension tube Kit Computar VM100;
  • GRAFTEK high frequency fluorescent light 11 ";

  -What hardware IMAQ I use compatible with Labview 6.0 or 8.6? Should I install also drivers for the hardware of the IMAQ when I remove the card IMAQ? All the solutions for my problems? Thank you very much in advance!

  Hi simpra,.

  Here are two links to articles that list compatibility between Windows & LabVIEW and LabVIEW and IMAQ.   Why do you say that the image processign software was not compatible with the LV 8.6?  A message appear?  Or it simply did not work?  Also, are you talking about Module Vision Development, by chance?

  I'm afraid that I can't help hard drive corruption, if that's the case here.  Have you been able to go beyond that?

  My suggestion is to upgrade to the latest version possible.

  I hope this helps!

  Kristen H.