Solution for Bluetooth PAN server configuration

-Internet on Bluetooth PAN profile
-Connection for laptop (Toshiba Satellite A300 1 2 (WinXP SP2) with Sony Ericsson K810i with BT PAN)
-Computer as a server of PAN (!). Lance PAN Mobile phone connection-> computer.
You can use internet to mobile phone to laptop.

But it's bug in Toshiba PAN-server - right click doesn't work in pan-Server tray :( (Local Russian (?))

* Configuration server PAN *.
1. options:
set of 2 boxes in the Bluetooth dialog options (service of pan, pan DHCP service), the [ok] button
2. Press win - r, type: cmd
Enter (case sensitivity "") ":"
CD "c:\Program Files Toshiba Stack\"
TosBtPSS.exe /END
TosBtPSS.exe /NAP

If it is absent pan server in the status bar - check your network connection BTPAN (Bluetooth Personal Area Network) enabled in the control panel and try
TosBtPSS.exe /NAP

((3 set the IP address for the network BTPAN connectivity: (I don't know how Toshiba DHCP server works, but it works!)))
You can use your own DHCP server configured...

You can make these instructions batch file...

Sorry, my bad English)

P.S. to the developer of Bluetooth PAN server: fixed a bug, please)


Thanks for this interesting article.

Tags: Toshiba

Similar Questions

  • time (for wsn 9791) in MAX server configuration


    I need to set up a time for my gateway WSN9791 server in order to ger readings with timestamp of remote nodes. How can I do?

    I already checked this forum and other sources of information on this issue and has concluded that the time server is configured by using MAX under "Remote Systems > NOR-WSN9791 > System Settings" but I have not found any arrangement for the NTP server there.

    My system configuration is:

    -Windows 7 Professional

    -LabView 2013

    NOR-WSN 2013

    -MAX 5.5.0f0 of worm.

    -a WSN9791 gateway

    -eight knots of WSN3202



    Finally, I asked the technicians support of OR who have come to find a solution.

    I report the message that describes the problem.


    Why can I not set a time for my NOR-WSN-9791 gateway server?

    It is a known problem in NI MAX 5.5 and 5.6 MAX OR. The time server option was not be displayed due to a change in the backend of the system settings page. Workaround to view the setting of the time server was created. The following steps will allow the option of time server OR 5.5 or 5.6 MAX MAX OR

    1. on your development computer, go to C:\Program NIUninstaller Instruments\MAX\UI Providers\DefaultRemoteUixml\ to C:\Program Files (x 86) and 64-bit windows \National Instruments\MAX\UI Providers\DefaultRemoteUixml\ for 32-bit windows.
    2. in the directory C:\Program Files (x 86) of Providers\DefaultRemoteUixml\ \National Instruments\MAX\UI, make a copy of the original mxrmcfg. DDPSystem.def.xml original-mxrmcfg file. DDPSystem.def.xml. this backup the original file to undo the changes.
    3. open in Notepad the file mxrmcfg. DDPSystem.def.xml

    4 replace the contents of the file with the following:


    5 restart NI MAX

    After you follow these steps, you will be able to set the time server on the NOR-WSN-9791 via NI MAX.


  • What are the best solutions for data warehouse configuration in 10 gr 2

    I need help on solutions to provide my client for the upgrade of the data warehouse.

    Current configuration: database Oracle This database contains the data warehouse and a LOBs more on the same host. The sizes are respectively 6 terabyte (3 years retention policy + current year) and 1 terabyte. The ETL tool and BO Reporting tools are also hosted on the same host. The current configuration is really poor.

    Customer cannot go for a major architectural or configuration to its environment changes existing now due to some constraints.

    However, they agreed to separate the databases on separate hosts of ETL tools and objects BO. We also plan to upgrade the database to 10 g 2 to achieve stability, better performance and overcome the current headache.
    We cannot upgrade the database 11g as the BO is a 6.5 version that is not compatible with Oracle 11 g. And the customer cannot afford to spend anything else than the database.

    So, my role is very essential in providing a perfect solution for better performance and take a migration successful Oracle from a host database to another (same platform and OS) in addition to the upgrade.

    I got to thinking now of the following:

    Move the database and Oracle mart for separating the host.
    The host will be the same platform, i.e. HP Superdome with 32-bit HP - UX operating system (we are unable to change to 64-bit as ETL tool does not support)
    Install the new Oracle 10 g on the new host database and move the data to it.
    Discover all the new features of 10gr 2 in order to data warehouse, i.e., introduction of Clause SQL TYPE, Parallel processing, partitioning, Data Pump, SPA to study the pre and post migration.
    Also at RAC to provide more better solution than our main motivation is to show an extraordinary performance improvement.
    I need your help to prepare a good roadmap for my assignment. Please suggest.

    Thank you


    Two major changes since the 9i to 10g which will impact performance are
    a. changes in the default values when executing GATHER_ % _STATS
    b. change in the behavior of the optimizer

    Oracle has published several white papers on them.

    Since 10g is no longer in the Premier Support, you'll have some trouble connecting SRs with Oracle Support - they will continue to ask you to use 11 g.

    The host will be the same platform, i.e. HP Superdome

    Why do you need export if you do not change the platforms? You could install on the new server, the database clone and then level to 10 gr 2 / 11 GR 2.

    Hemant K Collette

  • PDF has not been configured for this web server-2008 Server


    Try to open a report in preview PDF in the workspace and get the error "" PDF has not been configured for this web server ".
    I use a 32-bit server and hyperion 2008
    I already installed Ghostscript 8.51 in my server...

    Thank you

    Yes, I got the solutions... .i need to run the HRprinters.exe then I restart EN and pool services

  • EventID: 1206 Event Source: Active Directory Web Services ADWS failed to determine whether the computer is a global catalog server. What will be the solution for this.

    EventID: 1206 Event Source: Active Directory Web Services ADWS failed to determine whether the computer is a global catalog server. What will be the solution for this.

    Hi K jtm,.

    Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Forum. You can follow the link to your question:

  • Activate connections encrypted for the database engine (SQL Server Configuration Manager)

    Hi team,

    I have a quick question, on the protocols for properties of SQL. Option:

    SQL Server Configuration Manager > SQL Server Network Configuration > Protocol for SQL_xxx (right click) > properties, we can see two tabs:

    Tab 1: flags

    Tab 2: certificate

    If I put the value of Instance of hide = Yes, 'Force Enctyption', the fact must be set to YES as well?

    Or Enctyption of the Force must be activated in order to hide the instance?

    What is recommend settings?

    I can see there are good article, but would appreciate if a response.

    Thank you

    + Moin

    This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  • Solution for error MSB3073 observation about covers them IaaS Server (Web role)

    Server installation IaaS (Web role) failed with the following error message:

    [vCAC - Config.log]

    News: 2016-02-24 06 23 24 558: C:\Program Files (x 86) \VMware\vCAC\Server\Model Manager Data\DeployRepository.xml (707,5): error MSB3073: command "" C:\Program Files (x 86) \VMware\vCAC\Server\Model "Assembly-SqlInstall - f" C:\Program Files (x 86) \VMware\vCAC\Server\Model (x 86) \VMware\vCAC\Server\Model (x 86) \VMware\vCAC\Server\Model Manager Data\DynamicOps.Core.Licensing.dll "" C:\Program Files (x 86) \VMware\vCAC\Server\Model (x 86) (x 86) \VMware\vCAC\Server\Model \VMware\vCAC\Server\Model Manager Data\DynamicOps.ReportsModel.Common.dll "s - vraiaasdb.ra.local\vrainstance d 'vra' u" ' p * - crush - v "came out with code - 1

    What does the error 'MSB3073? And what can be the solution for this problem?

    I think that this is a general error code that seems to be a catch-all for different things.  We have recently improved our vRA 6.2.0 to 6.2.3 battery and came across this error during the upgrade of our first instance of web server IaaS.  We have upgraded first our independent orchestrators, then our identity server, our server load-balanced unit and finally our database.  Those, that everything is fine (less a minor problem with the upgrade of the server identity).  Then, we have reached this error during the upgrade of our first web server of IaaS (we have two that are load-balanced).  Finally, we had to join the VMware support and after looking into the problem, it turned to restore the cert of the identity in two vRealize device servers.  After doing this, all our IaaS servers upgraded without problem.

    https:// : 5480

    VRA-> SSO settings

    Again, this may or may not be your problem I've seen with different questions error code when searching on the internet for our particular issue.

  • Attempts to installation of Windows 7 Service Pack (x 64) leads to "Bluetooth Stack Server" "AppCrash": no wireless connectivity possible!

    I realize that my question is about the hardware and drivers that are not Microsoft, but all the trouble seems to begin with the fact that the latest version of Windows Update attempts.

    I have reset the settings of update on "Automatic" after missing the guests of installation, leading to several attempts installation of Windows 7 Service Pak for x 64-based systems.

    On installation/configuration logoff never surpassed ~ 10% during "installation failed, returning from changes" message appeared before the shutdown.

    On reboot, the error message: "Bluetooth Stack server has stopped working", problem report Details indicate: "AppCrash".

    Today, for the first time in ~ a year, brought my HP Probook 4530 s to a reliable wifi hotspot 2011: "no public network detected" appeared, everyone had no problem.

    The "centre mobility Windows", which usually has a box indicating the status of LAN wireless, had this box is completely missing.

    Check the two Bluetooth and Realtek PCIe GBE Family Controller (devices used for internet connectivity?) indicate that "the drivers are up to date" and "this device works correctly.

    I am running Windows Security Essentials and Malwarebytes AntiMalware.  Also recently installed the free version of SpyBot, run a daily scan.

    I've never really had any problem/detection of serious virus/malware that I'm aware of.  Windows 7 has been well up to this point.

    Also tried a system restore to BEFORE the Service Pack update attempt: it had no effect on the detection of wireless connectivity or a connection.

    If anyone can describe a troubleshooting chart that might allow me to again connect to a wifi hotspot, I would be very grateful.  Thank you.

    I should finally a solution to my inability to access a local signal of the WiFi for my laptop.

    As stated in my first post of the question, the problem started after a sudden error message "Bluetooth Stack Server."

    All the remedies, I've tried are listed above.

    This HP laptop came with a general diagnosis called HP Support Assistance program.

    Recently, I downloaded a new version of this program.

    For the first time, an icon appears in the taskbar for the "HP Connection Manager", which indicates the activation state of all wireless and Bluetooth devices.

    The following State scored to WiFi (Wireless LAN): "disabled in BIOS F10.

    Since I was able to connect to a WLAN before the Bluetooth Stack Server error, this setting IS ENABLED: it was not "manually" disabled.

    I entered the system BIOS via F10 during boot and the following path:

    "System configuration" > "Integrated device Options" > "LAN/WLAN SWITCHING" > select 'ON'.

    Rebooted the laptop normally, a check for HP Connection Manager "indicated"enabled"for the wireless LAN setting, and"Windows Mobility Center"was now a visible box for WLAN/LAN status."

    I don't know how or why the BIOS for this parameter settings were off.

    Please mark this issue as resolved, with this post as the answer.  Thanks for your suggestions.

  • What is the best solution for this idea...

    I have a task I'm trying to test and understand what would be the best solution for this, any recommendations would be appreciated.

    Devices at your fingertips:

    -2 ESXi hosts

    -1 iSCSI SAN OpenFiler (new just installed the app)

    2 ESXi hosts run a small amount of virtual machines that are all in the same domain.  I want to have a file server (or a repository somewhere) that houses a folder with easily accessible software (OS, Office, etc.) on the field.

    According to me, that if I made a virtual machine with a large hard drive and share the software, this would not be the best way because it would be dependent on the OS.  Someone has talked about doing a separte VMDK for it and then install it on the operating system on the virtual machine. This way I could always remove the and mount it somewhere else.

    It seems a bit weird to me that the software within this "shared folder" will also be sitting on the data store (if I create a virtual machine and need to use the OS/etc).  Not that doubles the space for the same software (in the comments, then the data store)?

    What is the best approach to make this action which can be accessed at the prompt (mostly windows) in the field?

    What is the best way to stay away the software doubles in action and on the data store?

    Please forgive me if I put interpereted your question.

    The problem you seem to face is that you must mount the ISOs of VMS software and physical systems that are on the field.

    (please, correct me if I'm wrong on this)

    If this is the case, then the best way to do would be to create sharing NFS on the openfiler, if you use openfiler to main databases also then he would be better for sharing this was separated to prevent the other help to be able to tamper with the VMDK and VMX files for your virtual machines.

    This could then be mounted in ESX to access the ISOs. While being easy to install on Linux and Windows machines to access the ISOs.

    If you have questions about NFS mounting in windows, so, this link may help

    If you are needing to access the VMs software and it is mainly the downloading ISOs then th ISO directly to the data store is possible.

    This allows you to use ESX to mount the ISO on the virtual machine.

    On the point that the software will use double disk space when you install the software on a machine virtual car will be on the network share and the VMDK virtual machines in the data store. That's right, and that's by design.

    Each virtual machine under ESXI is 'independent' (

    This means that each virtual computer must have its own copy of the application.

    This perspective reflection of each virtual machine as a separate system of 'physical '. They interact with each other as if they were physical systems.

    Each VMDK resembles a physical hard disk. Being accessible (in most configurations) 1 VM at a time.

    So if you had a set of physical systems connected to a domain and I wanted to install an application on each one, then each would have its own local copy of the application. It's the same thing with virtual machines.


    If you configure a set of physical machines so that you run the software from a network share. It is possible to do the same thing using virtual machines using the exactly the same configuration. However, the chiefs more associated to this are important in both cases.



  • Web Server Configuration tool fails

    I remove Coldfusion MX 6.1 "works" of Windows XP Professional and installed MX 7. Met an error when installing on the wall of fire problems possible preventing complete installation.

    I went to the Web Server Configuration tool to configure IIS. When I clicked on the Add button, I get the following message:
    Could not connect to JRun/ColdFusion servers on host localhost. Possible causes: server not - running performer and fire wall blocking JNDI - restriction in host.

    I have disabled virus protection and Firewall window also well off the coast.

    I've reconfigured the jrun.xml and ColdFusion runs on its own server, but I wanted it on IIS for some tests.

    Thanks in advance.


    > Yes is all three. I ran the two instructions that you gave me and this is the result.

    Finally, we could be something. Follow the link that I have given above and scroll down to the bottom. You will see a post about Windows XP SP2 and socks.

    Apparently, there's a limit to how many socks open authorized on the operating systems such as Windows XP SP2 and Windows 2003 SP1. If we believe that, then your problem is caused by Windows XP. The default behavior of the wsconfig tool is to analyze all ports in the range of 2900-3000, exceeding of Windows XP SP socks limited.

    A solution would be to run wsconfig with a limited number of ports scanned. Follow these steps and then on the command line:

    C:\CFusionMX7\runtime\jre\bin\java.exe-DWSConfig.PortScanStartPort=2920-DWSConfig.PortScanCount=1-jar C:\CFusionMX7\runtime\lib\wsconfig.jar

  • My google search bar now lights up blue and I don't see what I'm typing. Why? I read somewhere that there is a problem with Firefox. Is there any solution for this?

    I don't know exactly when it happened, but one day my search bar Google turned blue when I tried to kick it. I couldn't see what I was typing. I did some research and some forums that it was a problem with Firefox. Have you heard of this? Is there a solution for this?

    Thank you for your help.

    Which may be caused by protection of typing"Comcast constant guard.

    'Configure the Anti-keylogger settings'-> disable

  • Bluetooth PAN connection

    Someone at - it experience with Sony Ericsson Bluetooth PAN connection?

    I tried to connect my k530i but it did not work (the Toshiba as a server). I have the newest Bluetooth stack, because after the right-click on the Bluetooth of the bar antenna, I can't choose Activate Pan group Ad - Hoc Network, is this normal?

    I have the Satellite P200.

    Can someone help me?

    Post edited by: Jay - J

    Or can someone explain to me why I can't connect to my laptop from the mobile phone (even I have already paired devices)? I can connect from laptop to your mobile phone. Is this normal?

  • Access to an Internet connection that is shared in M60 via Bluetooth PAN

    I created a Bluetooth PAN, I came to my office.
    I managed to make it possible for the Office to use a cable internet, cable connected to this laptop (M60).
    Desktop uses "Free wireless Internet": P via bluetooh...

    It is possible to do the opposite... in the internet Wi - Fi and cable office via Bluetooh PAN...

    I tried several times but did not it happen... what should I do...

    (By the way... How can I change the name of this apears in the post?)

    Thank you!

    You should take a look in the document HOWTO 'Internet on PDA via PAN using Notepad as gateway', which is probably not exactly what you want to do, but shows how it should work. You can find it here:
    ' '.

  • I have e-mail in the Outbox and cannot send... I receive emails, but cannot send... how someone at - it a solution for this?

    I stuck in Outbox of e-mail... .i can receive but can't send out of the Outbox.  Does anyone have a solution for this?

    have you checked the connection doctor to see if something is wrong with the smtp server

  • Question of 2012 of R2 group key Distribution Server configuration.

    Hi all

    I searched online for more information on the problems of kdssvc. and addition of KDSRoot keys that have been problematic.

    In looking Site and Services snap-in and display of the Service node information I see the Server Configuration file, but no input config key Distribution of Service Group.

    I don't see anything online that would allow me to recreate the Configuration of the server. Is there a way to re - generate the Cryptography keys properly here and allow me to move forward with additions of Cle_principale. I have a 2003 with a r2 dc 2012 functional area in the field of parent and child.

    In the test of items off I see kds configs are always available and kdsrootkey can be created after the deletion of the entry of the Server Configuration. I'm looking for documents of deep dive on the subject.

    Any help is greatly appreciated.


    This issue is beyond the scope of this site and must be placed on Technet or MSDN

Maybe you are looking for