Sorensen visa close error

Hallo!

Lately, I've updated my LabView 8.6 to 8.6.1 then lately, I get the following error message when you use the VI atteched:

Error-1073807338 at VISA near sornsg Close.vi-> output - Dima old.vi-> lambda_sornsg.vi-> COG.vi-> Ch2_main_with_s11.vi

Possible reasons:

VISA: VISA (Hex 0xBFFF0016) driver failed to properly close the reference object or session. This could be due to a mistake releasing internal or operating system resources, a network connection has failed, or a lower level driver or OS.

I have no idea of what the problem
Please advice
Shai

problem solved

the used progrem a visa near the GPIB which, by definition, is always open...

Thanks anyway

Tags: NI Software

Similar Questions

  • VISA resource error

    Hi, I'm getting "the resource is valid, but the VISA cannot currently access" error. " I use a 4 x serial usb adapter.

    Is it because I use modbus I get this error of visa. All of my com ports work correctly when it is connected to my other devices. Multimeter, power supply etc..

    In the interactive control of VISA my devices are labeled under

    It's the ony com port connected right now. I made a loopback test in labview using Scripture series and read vi and also to the MAX I can write/request to the device but there is no answer or a timeout error. I connect the RS232 to RS-485 to connect to a device of ADAM. All reviews are very helpful.

    Thank you

    Damien

    Hi Damien

    I confirm that you are experiencing an error of 1073807246 code?  It is possible that you did not close the reference to the VISA session in a previous program and as such are not allowed to communicate with him in another.

    The following links explain this more in detail and show that the VISA close function required to close the references you can do during the execution of your code.  Don't forget to close the reference every time you want another program to take control of the serial port, as labVIEW does not release from default serial ports.

    Error-1073807246

    Errors with VISAS screws

  • Question? CS4 installed on your new PC (windows 10).  Flash was not installed.  Try to install CS5 update... close error: bridge.exe

    Question? CS4 installed on your new PC (windows 10). Flash was not installed. Try to install CS5 update... close error: bridge.exe

    Have you tried closing the bridge via the Task Manager?

    Error: "Setup cannot continue until...". Adobe Bridge is closed. Adobe Creative Suite 5

  • For the Driver NI-VISA Wizard error

    Hello

    I'm getting a "ERROR-1073807175: field of bLength is incorrect for USB_ENDPOINT_DESCRIPTOR type" this error shows immediately after I click Next on the first screen of the wizard of the Driver NI-VISA.  I see no errors after the wizard creates the USB driver.  In fact, I write for the endpoint device USB 4 using this driver for NI-VISA.  My problem is that I can't read of 3 endpoint.  I don't know if this error has something to do with my problem.

    Is there a way can I fix?

    The version of the Driver NI-VISA is: 5.4.0.49152

    Fixed a problem.  Disconnect the USB hub that is built on my Dell Monitor Help.

    Thank you

    Pablo

  • VISA 1073807343 errors and 1073807202

    Hello everyone,

    I have several issues with the VISA 5.0.3 and LabVIEW 2010 SP1, and I don't know if or how they are related, so I'll post as much information as I have here. Please excuse the super post long, just trying to be thorough.

    Error BFFF009E (same as 1073807202 I think) appears to the MAX aperture as seen in attached ss1. When you try to open the VISA Interactive Control (IC), I get the message "failed to initialize the library VISA. The VISA interactive control utility will leave. "When I open any VI with a VISA resource and try to click the drop down arrow on the right to see the resources available, the arrow remains derpessed during a second, no field drop-down list is displayed, and then it returns to its original blank State. These problems all live together now, but before I could select BT VISA resources and use VISA IC, while I have always seen the error MAX.

    I tried to fix VISA, as well as VISA uninstall-reinstall 5.0.3 which I believe is the most recent version. No change. I also checked that visa32.dll exists as suggested in the article below. See systeminfo.txt attached to the installed software.

    http://digital.NI.com/public.nsf/allkb/1D1736BFD24A09878625742500241386

    This error seems to be related to an oscilloscope Tektronix DPO 2014 I connected via USB (or maybe something to do with TekVISA?). By this I mean that if the scope was connected when my computer started, this error occurs. When the field is not connected at startup, I don't see the same problems as above. Instead, I get...

    Error 1073807343 (BFFF0011) when you run a VI with a VISA resource to a serial device (see ss2), or connecting to the device in IC of VISA (see ss3). I also always see the error of BFFF009E to the MAX, but not the other problems on front. I can connect to these serial devices in hyperterminal and communicate very well here. Seems similar to the post below and also, I can't find visaconf.ini, but the solution does not apply as I LV 2010. In addition, ironically, I use VISA very well talk to the scope (whether to the MAX or LV) via USB if I connect after booting.

    http://forums.NI.com/T5/instrument-control-GPIB-serial/using-HP34401A-in-LabVIEW-yields-error-code-1...

    I use series of USB adapters made by Ultra (http://mail.ultraproducts.com/product_resources.php?cPath=35&pPath=782&productID=782 ) to go from instruments of series to my USB ports and the computer I'm unfortunately has no serial ports to be tested with, nor do I have another brand of the adapter. I know these converters can sometimes be a VISA problem, but I was certainly with it even without problem before.

    They that all seem to have intermittent problems, because I have seen both before as I have developed and pushed to go to strange as things exchanging (apparently identical) USB extension cables or restart a dozen times. This issue has been driving me crazy for weeks, I am looking for help to try to solve it finally.

    Thank you

    Ratti

    I think I got especially. Looks like it was TekVISA who got in the way, and if Visa32.dll was in the right place, it appeared (in properties > details) as the version of Tektronix, not the version of LabVIEW. After you have uninstalled all Tektronix as well as NI-VISA, he had disappeared, but no money to install or repair NI-VISA would be replaced by a version of LabVIEW Visa32.dll.

    However, with the help of the article from the link below, I discovered that the repair of the installation of the driver NI-VISA DURATION is what replaces Visa32.dll, as opposed to NO-VISA just as messages of error and other links seemed to suggest.

    http://digital.NI.com/public.nsf/allkb/B283196340462DFD86257633006DC799

    Now all the VISA stuff works again, except of course for the scope of Tektronix. I'll keep this battle for the future. Guess I just needed to talk to myself for a while.

    -Ratti

  • Visa timeout error-1073807339 reading

    Hi all

    I'm doing a command autoscale on a DSO-A4034A Agilent (Keysight) connected by ethernet.

    But for some reason, I get a time-out error. When cheking to find system errors.

    I have set up the session visa in 'MAX' and use the name of the session of the instrument of the call in the VI.

    I founded these screws on the Agilent instrument driver. and I can do all the other stuff I have to do without errors. EMPLOYMENT INSURANCE. the installation type measures Aqusition read data and so on without error.

    The error is caused by reading order just after the ": SYSTEM: ERR?" command under the request of error VI.

    I have updated the firmware of the scope and upgrated 15.0.1 VISA but so far without success.

    There is no problem when I turn the "climax of the performance"...

    Is there someone who can give me some advice about where to look this anomaly? Any help would be gratefully recived.

    / Best regards Rasmus

    Rasmus.Olesen wrote:

    There is no problem when I turn the "climax of the performance"...

    Crying just "timing issue."  Add a little wait between ordering autoscale and error checking.  It is likely that the oscilloscope does not resemble incoming orders when he assures the autoscale.  If you wait for it to do the job.

  • VISA-1073807343 error code when using ResourceManager.GetLocalManager (). FindResources (filter) to detect the map of Pickering PXI

    I'm upgrading our test system for Windows 7 and NI Developer Suite 2012 DS2 in Windows XP and NI Developer Suite 2008 4th quarter. I have a problem with the help of VISA to detect devices PXI of Pickering. The problem occurs with the next .NET NationalInstruments.VisaNS.ResourceManager.GetLocalManager () call. FindResources (filter). I use the filter "PXI? * INSTR.

    To trouble shoot this problem I was using the VISA program FindResources.2008 c# example. I get the following error message when you apply the "PXI? * INSTR"filter. "Where not enough information or the device or resource is not present in the system. VISA-1073807343 (0xBFFF0011), ErrorResourceNotFound error code.

    Looking at other markets, I infer that VISA is not find the maps. I came across the same error message when I tried to launch the "GPIB? * INSTR"filter however I determined that there was a problem with the NOR-488 driver. 2. after having repaired the driver of the FindResources.2008 program would find the GPIB instruments using the "GPIB? * INSTR"filter.

    Max the Pickering cards appear in "Devices and Interfaces" and are listed as follows:
    12: PCI Device 'PXI12::9:INSTR '.
    15: PCI Device 'PXI13::13:INSTR '.

    In XP, the cards have been identified as:
    PXI12::9:InStr (Pickering 40-785-522)
    PXI13::13:InStr (Pickering 40-780-522)

    Also Max for each device, I am able to open the Panel to Test VISA.

    Any ideas why the VISA is not able to detect these cards?

    Thank you

    I thought about it. Apparently I needed Windows 7 to install the driver for cards of Pickering. I guess the "PXI VPP / VISA drivers" supplied by Pickering Test would take care of this.

    Until Windows has installed the driver of Pickering cards have been listed as a PCI device under 'other devices '. After installation, the cards have been listed under "devices PXI of NI-VISA.

    MAX the card now are listed as:

    12: Pickering 40-785-522 'PXI12::9:INSTR '.
    15: Pickering 40-780-522 'PXI13::13:INSTR '.

  • NI-VISA Setup error

    Hello world... When you build an application in labview, you have the option to include some other installers (National instruments installers)... If I include NI VISA Run time 5.1.1 in the installation but the computer of a given user has already does VISA Run time 5.1.2 installation will fail in this user's computer... it gives the error:

    alpony01 wrote:

    No, at some point during the installation process, you can click "NEXT" to continue, and he said:

    Cannot install

    • NI-VISA 5.1.1 (superior version already installed)

    Run management (superior version already installed)

    at this point, your only option is to cancel the installation process...

    You get this "unparalleled option" so anything that can be installed is installed and the only thing left to install that you wanted to install cannot be installed.

    Or, more simply, you can cancel only because no installation is available at the facility.  There is no 'Next' because nothing is left to do.  Normal Windows Installer behavior!  (If I was the designer of MSI, that button would read 'OK' and not 'Cancel', but I'm not multilingual)

  • VISA Read (error BFF0015)

    Hi all

    I use COM VISA library and c# communication with my instrument via TCP/IP.

    I add the reference "VISA COM 3.0 Type Library ' to my c# project and try to establish communication using the following codes:

    *********************************

    Ivi.Visa.Interop.ResourceManager ResMsg = new Ivi.Visa.Interop.ResourceManager ();
    Ivi.Visa.Interop.FormattedIO488Class ioClass = new Ivi.Visa.Interop.FormattedIO488Class ();

    Imsg = Ivi.Visa.Interop.IMessage (ResMsg.Open ("TCPIP0::192.168.0.170::10001:OCKET", Ivi.Visa.Interop.AccessMode.NO_LOCK, 8000, "") as IMessage);
    ioClass.IO = Imsg;

    ioClass.WriteString ("* RST", true);

    ioClass.WriteString ("* IDN?", true);

    String ret = ioClass.ReadString ();

    Console.WriteLine ("ID:" + ret);

    **********************************

    I could write "* RST ' command to the device without errors. And I could see that the device really do a reset of the command.

    But when I send "* IDN?" and read the answer, I still get a TIME_OUT error. Even if I add "\r\n" at the end of the command and increase the value of the time-out period, can I still the same error. Not only "* IDN?" but also another order of reading as "* STB? ', they all can the same timeout error.

    But when I use the VISA-ReadSTB function, it returns the correct data.

    I also tried to use Labview VISA-open, entry VISA, VISA-read for the same test. I also have an error (BFF0015) after VISA-read.

    I also use a programm IO monitor to view the data. I find that I have seen the answer, but I still have a time-out error. Currently, I could only read the answer by Agilent IO control successfully.

    I'm using c# 2008, Labview 8.2.1, VISA 5.0.3

    Any notice will be really appreciated!

    Kind regards

    Please take a look at this KB. Maybe this can help you solve your problem.

    Why should I receive Timeout error-1073807339 on VISA Read or Write?

    http://digital.NI.com/public.nsf/allkb/874B379E24C0A0D686256FCF007A6EA0?OpenDocument

    See you soon

  • Why do I get VISA code error-1073807202 when you try to connect the PXI-2565?

    I got the 1703807202 error code (a code library required by VISA is not found) every time when I start the computer and used 'Initialize with topology' first connect my channels.  This error could disappear if I start MAX and open devices and interfaces, then re - perform the same task.  How can I get rid of the error?  Thank you.

    My bad, GPIB driver has not been installed

  • C Code NI-VISA linker error

    I wrote the following C command to place orders SCPI to Rohde & Schwarz FSL

    #define NIVISA_PXI
    #include
    #define MAX_CNT 200
    int main (void)
    {
    Status of ViStatus; / * For error checking * /.
    ViSession defaultRM, instr; / Communication channels * /.
    ViUInt32 retCount; / * Returns the number of I/O string * /.
    Bruno buffer [MAX_CNT]; / * Buffer for channel I/O * /.
    status = viOpenDefaultRM (& defaultRM);
    If (status<>
    Returns - 1;
    status = viWrite (instr, "* RST", 6, & retCount "");
    status = viClose (instr);
    status = viClose (defaultRM);
    return 0;
    }

    I get linker errors.   [Linker error] refers to 'viOpenDefaultRM@4' the undefined

    I used Bloodshed Dev C++. I have included the header files in the VXIPNP folder to include folder od Dev C++. He had 11 files.it had 4 header files visa.h, visatype.h, vpptype.h and rsfsp.h

    I have to install the header file and library? Please help, this is the first time I am using VISA. H

    Excuse my ignorance... but I've never worked with .dll in C++ can u explain how can I say my linker where is the file 'visa.dll '.

    Thnks

  • VISA write error 1073807298 with mbed

    Hello everyone. I use the mbed card for my new project.
    I'm not familiar with the mbed, so I tried to do a few led flashing with labview.

    I get the error message 1073807298.

    I tried hunting VISA and VISA defined I/O as recommended messages previous but has not solved my problem.

    Can you help me please?

    Hi mejrissi.chiheb,

    Have you seen our paper that deals with this error?  I think he should provide more details on why you see this behavior.

    Best regards,

  • BOUNCING VISA Write error - hair pulling

    Running an application that uses some standard features.  Lies in stepper motor which is controlled by simply sending chains of command to the inverter via a serial connection.

    Update for Windows 7 (from XP) and thus to level to 2013 LV.    Now all of a sudden I get errors of the vi that writes to the port series. He'll sometimes for a few hours before appearing, sometimes 15 minutes.  There is not much consistency as to which iteration of the vi pops up the error.  I added delays here and there, put a delay in writing vi (attached), added a clear before writing pad, etc, etc.  This bug won't go away.  This is the error that appears...

    I have attached the vi.  It is about as simple as they come that's why I'm pulling what little hair I have left.  Two changes in this version of the original that ran forver on XP, the delay of 150ms between writing and close System (since door to 400) and I also changed the time-out on the configuration of ms 10000 to 5000 ms (10s and 5s).

    Once this happens then all series the connection with the computer is watered and I have to restart the system to get there again.  The computer, a relatively new dell, has a port built series ini and I use an expansion card StarTech for two additional ports. (2-port PCIe RS232 w / UART 16550)

    ANY help is very appreciated on what having to reset the system 10 - 15 times a day is killing me.


  • Signal and NI VISA Express - error-1073807202

    So I did a search on this very common error that I'm having also, see error1.jpg. So, one of the answers was to try to make an installer that I'm trying to do, see error2.jpg. I hope it's the right thing to check for the error (nobody said in previous posts I've read). Then he asked me to find the Signal Express. So I get out my DVD of LabVIEW 8.5.0 and point to the location (drive D :), see error3.jpg. But Labview then told me that it is an invalid location. I mean WTF? I'm really getting annoyed now and do another search forums. I find a post that says to look in MAX to see where the Signal Express is located. So I have this and then put this location in the installation Builder dialog box. Guess what he told me, see error 4.jpg. So now what should I do?

    The box checked in the picture 2 is correct, that you can find more information about why your Installer needs of these distributions here:

    Why do a 'missing' Distribution or "Necessary Distributions" error when you try to build a Setup program?

    http://digital.NI.com/public.nsf/allkb/C3666BA408F81E59862570D20056E692?OpenDocument

    If your bad having to locate distributions try re installing the main drivers DAQmx VISA and also Signal Express, in this way, you know exactly where are the distributions.

  • "compiledbot was an error and needs to close" error when opening Commission Maniac

    How to open a file that is displayed with the error 'compliedbot must be closed?

    I downloaded a program "Commission Maniac" and when I tried to change the file formats for the mail file that commissionmaniac became stored in the directory root of the archives, and when I try to open zip it says "compiledbot has had an error and needs to close." How can I get this file to open it?

    Perhaps you should consider asking the seller to "maniac of the Commission".

Maybe you are looking for

  • How to increase the height of the scrolling frame?

    Whenever I open a website that has a frame in it, the view-able area is very small, and I need to scroll down to see the information, even if there is plenty of room on the screen. (Embedded pdf files I have this problem, also work sites that have li

  • I have an iphone 5 s when I opened the app screen ther place is no icon of the application not found

    I have a 5 s 7.1.2 IOS, model MD440LL/A.  I do have the App Store icon on the home screen. When to go to the ITunes App & in that updated settings App is turned on. Use also. as cellular data are. Kevin

  • print from Fax on my 8600 pro history

    Do not receive faxes on my 8600 pro can not haue what it set up right.  Received a fax known and he receifed all 13 pages, but not print them.  Looked in the history of the fax received and found that he received, but the deal was the printing of thi

  • Windows 7 to Windows 8 back in Windows 7

    After the installation of Windows 8, I can return to Windows 7? and how?

  • Centro de Servicio Seguridad

    Con help me to favor: Sell me a colo rojo of message: Activar el servicio windows Security Center, Ahmed el centro of activities y pulso en activar ahora luego sale otro message than no dice is you can start the service of windows security. Not to do