Sound does not work on the merger

Lately every time I start my Vista VM I get no sound. From the start, I got a fusion message that says "error starting sound stream. Playback may not work. "Regardless if I run anything on this side of mac who is playing a sound. I can't think of any changes that would have caused this. I checked the settings to make sure that the sound card is enabled. I did no recent merger or vmware tools update and I am on version 5.0.3. My guest is 32 bit Vista ultimate sp 2. I have mac 10.8.3.

Watch: sound does not work in the Windows virtual machine (1003425)

Tags: VMware

Similar Questions

  • Satellite U200 - sound does not work after the installation of Win8.1

    Hello guys,.

    I have some old Satellite U200-165. I installed windows 8.1 Enterprise assessment successfully after that I changed the hard drive SSD, but the sound does not work. Windows showing that his work perfectly, but it does not come out.

    An advise please.

    Satellite U200 is a pretty old and not supported for Win8 or Win8.1 machine. I think that we have no report on this forum how this old piece of equipment works with Win8.

    If the sound card is properly installed, have you checked all the sound settings?
    I presume that the same problem is with a headset, right?

  • Satellite L655 - sound does not work on the new install of Windows 7 Pro x 64

    Howdy all,

    I bought a Newegg L655-S5111, which was on sale, put an SSD, and then installed a legitimate copy of Windows 7 Professional 64 - bit, I got from my current employer (I'm a computer scientist). I've updated to the latest revision of the BIOS (1.70), and I have all the updates installed Windows, all drivers installed, including the correct drivers Conexant HD Audio and ATI HDMI Audio. Unfortunately, the sound does not work. Sound works briefly during my first install of Windows 7, then I cut it up until I could get it set up with a helmet. When I disabled it, she had stopped working.

    This laptop is less than 3 weeks at this point, old and I get no audio on headphones or speakers, even if Windows displays clearly no problems with the drivers, they have the latest version on a new installation, and I can see the audio mixer game. The laptop built-in microphone captures sound as well. I think that's probably not a matter of the physical interconnection, but more likely a software problem, I just have trouble identifying where it is.

    I have also no related error message than any where in the case of newspapers.

    Post edited by: ADMIN

    Can you please do a test and install original recovery image Toshiba, that you got with your laptop on this new SSD, just to see if it will work with the original image.

    Recovery image contains all the necessary drivers and OS is perfectly configured so each piece of hardware in your laptop should work correctly.

  • IdeaPad Y570 sound does not work all the time

    My laptop is Y570

    The question, the sound does not work

    When I start windows I can hear the windows startup melody plays when I start windows media player, video YouTube, VLC player or any other software that requires sound it will not work unless:

    I go to sign in-online sound-online right click test Realtek HD Audio, then the sound works.

    I tried to fix it by the installed driver and reinstall, I went got the driver from Lenovo and it did not work. My speakers are JBL

    Please help me

    uninstall both... reboot then install realtek then reboot then install the drivers of onekey theater.

    http://support.Lenovo.com/en_US/downloads/detail.page?docid=DS018489

  • Satellite A200 - 1 M 7: the sound does not work after the downgrade to XP

    Hello!

    As in the topic I have a problem with my sound card - it simply does not work under Win Xp (under Vista everything worked).

    In Device Manager I have two 'points of inquiry:
    -Controller\ PCI memory
    -Unknown device
    I assumed that the unknown device is my sound card, but still can't make it work :/

    I've already upgraded the bios and install page of toshiba Realtek drivers.

    Really need help.

    Adrian

    Hello

    No sound after installing XP operating system. What to say man I searched here in the forum similar threads and it seems that it is a common problem.

    But you worry about don t; I think that I found the key ;)
    After installing win XP, you must update the latter State. Install all the patches and hotfixes provided by Microsoft. You must use the website to update Ms. The tool on this page checks the system and selects all necessary updates!

    Very important are the patches; KB888111 and KB835221
    These hotfixes must be installed before installing the sound card driver.

    The Realtek sound card driver can be downloaded from Toshiba or on the official website of Relatek page.

    By the way; It is very important to install drivers in the correct order. On the Toshiba page, you will find the installation instructions. So please follow the guidelines mentioned in this doc.

    concerning

  • Sound does not work on the computer and the volume icon does not appear in the system tray.

    Original title: my sound icon has disappeared from the taskbar.  The Control Panel indicates the sound is on, but I can't hear anything.  What happened and how do I get my sound back?

    Have a Toshiba laptop that always displays the lower icon audio in the right hand of the screen.  The sound icon has disappeared and I can't hear anything.  I check Contol Panel and sound, and he says it works and is turned up... but I can't hear a thing.  How can we retrieve icon of audio and how I can hear sound?

    Hello

    Thank you for your response.
    I did a "System Restore" and the icon reappeared, and the sound now works.
    I restarted the computer a couple of times, but that does not solve the problem.  Also, I went into the Panel and checked to see if the speakers were working and were lit, and they were.
    It wasn't until I did the restore of the system that the icon reappeared and the noise began to work again.
    Thank you.
  • Deliver the sound does not work on the computer.

    So sometimes the sound on my computer works just simply. This problem occurred recently: after watching a few movies on the computer using a double headphone output (I was watching with my sister) it worked fine, no problem. A day or two later, I tried to watch a video (on headphones) and the left earphone wasn't working - no sound didn't go out. I figured out the headphones were very good, but it's the computer problem. He started to work again the next day, but then most problems - sometimes no sound at all. No speakers or the headphones. Ever since then, it's like Russian Roulette, sometimes it is sound, sometimes it does not. I just wish the best. I tried troubleshooting and he said that he could not detect any problems. I tried to it turn on and off again? Yes, several times.

    I'm desperate for help! Thanks in advance.

    Hello

    If the computer has a separate sound card remove ALL power and then remove and reinstall
    the map. If it's built-in sound so either she developed a hardware problem or
    something interferes with him. If the device goes wrong it may be replaced if

    a separate device or it can be disabled in the BIOS or Device Manager and
    a card can be used OR a USB card sound.

    Check in the Device Manager - Sound - Driver tab - go to the site of the manufacturer of the audio device
    Download and install the latest driver.

    ========================================================

    Sometimes 3rd part antivirus/security or another program may be causing interference.

    How to perform a clean boot for a problem in Windows Vista, Windows 7,
    or Windows 8/8.1
    http://support.Microsoft.com/kb/929135

    Other programs to help:

    Autoruns - free - see what programs are configured to start automatically
    When your system boots and you connect. Autoruns also shows you the complete list
    locations of registry and files where applications can configure start automatic settings.
    http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
    Process Explorer - free - find out what files, registry keys, and other objects
    processes have open, which DLLs they have loaded and more. This unique
    powerful utility will show you even owned by each process.
    http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx
    =========================================================

    Check with support from the manufacturer of your system (manufacturer of motherboard for customized systems) their
    online resources and the drivers and ask questions in the forums about known problems.  Or
    with audio device manufacturers / real sound if a separate device/map.

    No sound in Windows - use the troubleshooting tool
    http://Windows.Microsoft.com/en-us/Windows/no-sound-help#no-sound=Windows-8&V1H=win8tab1&V2H=win7tab3&V3H=winvistatab1&v4h=winxptab1

    =========================================================

    Check if you have the latest available driver. Download and install the latest driver.
    If you have the latest driver to re - install the same.

    More troubleshooting if necessary:

    Microsoft - hardware and drivers
    http://Windows.Microsoft.com/en-us/Windows/hardware-drivers-help#hardware-drivers-help=Windows-8

    Why Windows is not find my device?
    http://Windows.Microsoft.com/en-us/Windows-8/why-isn ' t-windows-conclusion-device

    What happens if a device is not installed correctly
    http://Windows.Microsoft.com/en-us/Windows-8/what-device-isn ' t-installed-correctly

    Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
    http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

    I hope this helps.

    Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

  • Sound does not work after the computer Windows XP formatting.

    Hello

    I am the customer service representative who is to ask your question on behalf of the client. After reformatting his computer Windows XP and installed all the drivers, its only driver no longer works. It has an Assembly of Dell 3000 Windows XP Professional. The device that is not working is a Soundmax audio controller that has yellow mark in the Device Manager. It ran Windows update troubleshooted it and restarted the machine and the problem persists.

    Perhaps the sound card must be replaced.

  • Internet and the sound does not work after the ATU Vista 64-bit

    I really didn't want to display in the hope I would find the answer using Google, as I did in the past, but this one i can not find the answer for.   2 days ago I d/l a program called Advanced System Care. I was told by 3 of my friends it works well to clean your junk files, Defragging ect ect.

    After d/l and the operation of the program, I had to leave and shut down the system. Today I start everything is fine, and then I noticed that I have a red X on my speakers. This is not the red X you get when cut there a smaller lower-right next to the speaker in the toolbar. When I mouse over it, it says "Service Audio work not" when I click it to repair, so good it shows all is working (volume mixer control is non-interactive) then I go to control panel and click on the speaker and I get "this computer cannot play audio because the windows audio service is not enabled.»   You want to enable "I click Yes and it brings back me just in the region, that I was when I clicked on the small speaker in the toolbar with the red x.»  Everything always looks the same as it was when I put in place.

    Is there anything else I can look?

    Second problem happened at the same time.  I have the same red x on my 2 computer screen in the toolbar on the bottom right. When I try to repair it it says this "this service cannot be started because it is disabled or because it has no enabled devices associated ' when I go to Device Manager and check to see if it is still showing my d-link wireless there is black! on a yellow background. When I try to access the computer to find local internet connections, it says that it can't find. I know that my Linksys is working because my Iphone is connected.  I already tried to install a cord between my router and my system and it still does not notice the internet even when you try to reconfigure.

    I read where I can make a dirty windows vista installation and fix it. but I really hope that there is a better way.  I also tried to restore my computer to last week when I made a back up and it seems after the use of this program, that he got rid of that as well. So now im out with to be able to roll back before I D/L this close program useless lol

    I'm using Vista ult 64 bit, that the computer is built for gaming and music. OCed Q6600 to 3.2 4gig ram 8800gt 2 in sli on a configuration card XFX mother if any other system or other questions please do not hesitate to ask.  I hope that someone has had this problem and can help me to solve it.  I don't want to reformat my HD or what I really want to pay Microsoft to talk to them on the phone

    Thanks for your help

    After 3 hours on the phone with the microsoft problem solved. Seems some how using CSA and the update of microsoft it limited my computer to start all programs at startup.

  • HT-TC 260 Sound does not work via the video inputs

    I recently bought a bar of its HT-CT260.  If I plug the cable box bar using the optical connection, then it works fine.  If I plug the optical connection between the TV and my PS3, then it works fine.  But I get no sound, if I plug the bar directly to the optical input on my Sony KDL-40xbr2.

    Oddly enough, the bar works (TV at the bar) if the TV is on channel antanna, but not if I use the video inputs for my box of cable and the PS3.

    Spend 3 hours with Sony (useless) online support and assistance phone sony (well, but not solves is not the problem).

    The optical plug is designed to produce sounds when the content you watch contains audio digital. (PCM or Dolby Digital® technology) This feature is available on a selection of digital and video streaming shows and is not compatible with the standard of cable stations or analogue.

    The KDL-40XBR2 TV can only output sound via the connection perspective If the TV is using its own tuner (i.e. If the TV is connected to an antenna or direct cable line in the wall) which explains why you do not get sound when using the video inputs because cable box and PS3 use external tuners to your TV.

    If my post answered your question, please click "accept as a Solution.
    This will help other users to easily find their answers when you browse the site of the community of Sony.

  • Sound does not work in the iOS

    I got a warning saying that the audio preloader would not work in iOS (7.1.1) - However, I get no audio at all. Is this normal?

    Hi, in mobile audio devices must begin with the users.  All auto play dosen´t work. You need a button to play the audio file concerning the Caisse

  • Sound does not work after the creation of DVD

    When I saw my movie in still the audio works but after that I have export to DVD, it no longer works. Any ideas?

    Thank you

    Chris

    Well, you've done most of the things I would say. This individual WAV would be high on my list.

    This leaves wondering what brand of blank media are you burning at?

    Also, as a test, you can burn the file and then play this folder with DVD playback software? How does it work?

    One last thought, your audio is connected to your set-top player, or whatever it is you are testing on. Please don't laugh, as has happened at least two other posters over the years.

    Good luck

    Hunt

  • Portege R200: Sound does not work on the modem

    Does anyone have any suggestions on how I can get sound of my modem?

    I have a laptop Toshiba Portege R200 with Win XP Version 2002 SP2 with a Toshiba Software modem on COM3. When I dial a number with the modem there is no sound, even if the modem work and connect to my server.

    · The sound works for other applications and Windows itself, so I know the speakers work.
    · I moved my hard drive on another laptop and had the same problem, so I know that it's a software issue and not a hardware problem.
    · In Control Panel sounds and peripheral Audio, the volume is set to high and the Volume, phone, Mono control Out and other volume settings are all rich.
    · In the modems Control Panel Options and the modem speaker volume is set to high
    · In the properties of the Modem, it indicates that the device is working properly
    · Through HyperTerminal, I sent the AT & F, ATM2 and ATL3 commands to be sure, has everything been settled properly (and the answer to all was OK)

    Someone at - it see this problem with the modem doesn't do not all sound? Suggestions?

    Thank you!

    Mike

    Hello

    I put t know which sound modem tell you exactly but is it so important to you?
    If the modem works correctly and you can connect to the internet, why you want to have the sound of the modem? Maybe you hear the strange sound of modem that is displayed when the modem tries to build an internet connection.

    You can try to change the numbering in help. Maybe it s in legumes and want to have the tone.
    To do this, you will need to enter in the Control Panel, and then select the modem.
    Please indicate the location on the dialing rules tab, and select Edit.

    You can then change the dial using the general tab.

    It will be useful.

  • Sound does not work on the Internet only

    My sound stopped working with multiple browsers (Safari, Firefox and through Parallels Internet Explorer on Windows 10). No difference if Parallels isn't running.

    Alerts and iTunes are great! I can play jpeg via Adobe Photoshop organizing. Everything except the internet.

    Setting up audio and Midi has 44.1 KH, 2-channel 24-bit format.

    The volume is not cut.

    I rebooted the machine (MacBookPro Retina early 2013 ElCapitan 10.11.5 running) with no improvement.

    Anyone have any ideas?

    I could try to create a new user and see if he has the same problem. If so, I start in safe mode and test.

    OS X El Capitan: start in safe mode

  • Sound does not work after the installation of beats audio

    Laptop: HP DV6-7001TU

    OS: Windows 7 Home Premium (the laptop came with HomeBasic, I got a copy of used HomePremium).

    I came across this problem recently which was not there before, I bought the computer as soon as I bought almost 5 months ago, I did a format complete and installed Windows 7 Home Premium (hate the bloatware that comes + it came with HomeBasic).

    Audio worked fine uptill now, my brother got a new laptop DV6 with beats the other day, and the sound was better than what I had. So I thought it was the default sound drivers I had. I went there and am myself the audio drivers. Now, since I update the drivers, I have no sound on my speakers if I use not his for a long time, if I restart the noise comes back, but if I do not use anything his bound for awhile and then try to use it again, it disappears.

    The solution that I found (to restart the computer every time), is that if I click on the vloume icon in the taskbar and then click on the speaker icon that opens "speakers and headphones properties" and then click OK in the window that opens, the sound comes back.

    Things I've tried so far

    1. Once I have no sound, again, I tried the windows "Find and fix audio playback problems", he found nothing.
    2. I have uninstalled/cancelled codec IDT of the Manager of the devices, the drivers were responsible for default and the sound was back, once I did a Windows reboot find the IDT drivers and the problem was back.
    3. I have uninstalled/cancelled drivers IDT, uninstalled the software programs IDT add & delete, downloaded a new copy from the link above and installed again, same problem.

    Help, please! It drives me crazy, I get a lot of Skype calls during my work hours and I have to constantly to cling on my clients and that the correction of the sound and to recall them once again, this is highly inconvient.

    Software IDT uninstalled, deleted/rolledback the pilot programs, downloaded the HP Support Assistant and recommended IDT software, installed via HP Support Assistant. Everything works fine now.

Maybe you are looking for