Sound on Portege 4010 problems

Similar Questions

• The Portege 4010 problems

  I recently bought a refurbished Portege 4010 and it works fine, except that pips sound a lot. It seems to be random, may occur as once in 3-4 seconds, or it may seem fine for a few minutes then * glitch glitch glitch *. Looks like the tempo of the sound is slowed and then catch upwards, and it sometimes makes a noise dry sound.

  I have a Portege 4000, which did explode a little sound each time than in quite awhile, but he appeared rarely as once every 30 minutes and was barely noticeable. On this 4010, it's much worse.

  I have all the Toshiba official drivers, running a twisted installation of XP SP2. I tried a clean install and the sound has the same faults.

  Right now I use ULi drivers I found on the Nvidia download page, they have helped a bit, the sound bugs are now more sporadically, but when they occur (once every two minutes or more), they are always as bad as they were at the start. Also, ULi drivers are sound drivers only I could find that have sufficient volume levels, with the drivers found on your site the wave volume distorts when turned over 20-25%, now I don't have to worry about that while she prepares to max as do some games, the sound will not be distorted. I had the same problem on my old Portege 4000, at the time I did not know the difficulty pilots and used a volume reduction program to force 'bad' apps and games to mix parameters.

  The 4010 is such a portable grand, when you use a second battery, he gets the same battery life of 5 hours of the 4000 and with more processing power. It's a shame that something minor like a sound chip of ruins all the fun. Yes, I know it's pretty old, but as long as he does his job, which is no big deal.

  So is there any fix I can try? Thanks in advance.

  Good job!

• Keyboard on my Portege 4010 problems

  Out of the blue, I have keyboard problems on my portege 4010. I have bad start up and now that I have, I can't access some of the problems, the keys get stuck, funny noises... beeps all the symptoms of a questionable keyboard. What I can do, otherwise, buy a replacement keyboard (v.expensive) or use an external keyboard?

  I personally have not dropped something on the keyboard, so problems can just be from one day to the next, or should interogate my husband.

  Hello

  Maybe your husband has changed something? ;)
  But seriously, if you have some problems with the boot and keyboard in my opinion, you should try to pick you up BONES. If the malfunction of the same images I recommend to contact the ASP for more information.

  Good bye

• Wireless - connection Portege 4010 problem

  I have a 4010 Portege (PP401A-024FMP), who refuses to connect through the mini pci wireless lan card. It identifies when there are wireless networks autour, but does not connect. I even created my secure and open wireless network to see if it was a security issue nothing works.

  The laptop is running a new copy of Windows XP SP3, including relevant drivers from Toshiba Web site.
  In addition, I also tried a fresh copy of Ubuntu 8.10 to see if it's XP causing the fault - Ubuntu do not connect any.

  There is no problem in (XP) Device Manager wireless card is faulty even if it displays the wireless networks?

  Any help is appreciated!

  Are you sure that's not because of false settings on your router?

• Portege 4010 - after upgrading RAM, nothing happens

  Hello
  A beginner very believed in that.

  I picked up some 512 MB PC133 SDRAM for my 4010 but when I put them in the slots and pressing the power button... Nothing happened.

  Would appreciate any help at all...

  Hello!

  Yes, maybe 2 x 128 MB modules were the original modules, that they were delivered with the laptop.

  I think you should try other modules. If you use the modules of noname, they could be possibly not work or problems as bluescreens etc.
  As far as I know that the Portege 4010 can be upgraded to 1 GB of RAM. You can use two 512 MB modules then you should buy RAM from Kingston of high quality for example.

  Here is the part number for Toshiba for a 512 MB module I founded with Google:
  PA3108U - 1 M 51

  Good bye

• WLAN card portege 4010

  Hello!

  I'm having problems with my card wireless integrated I own av Portege 4010. It seems to be allright in the properties of the device, but I don't see any network when I scan with the program integrated into 'control panel '. It should show a strong network'I'm 10 feet away from

  Its enabled in bios, the switch on the computer is on

  I think that the camera is Intersil Prism2.

  I use different wlan devices every day and I miss some software for this built in card - preferably software that shows in the systray

  Hello

  I do not know who built in the program, you use, but please check in the properties of connection network wireless tab wireless networks if option called use Windows to set up... is disabled. It should be disabled if you want to use some other application or client for a wireless connection.

• Portege 4010: No boot

  Hello everyone,
  today I received a used Portege 4010. I have pluged in the cable and I wanted to start. Green DC, lamp orange battery and when I walk there gree power lamp appears. But that's all, nothing more. The screen stays black, only a very small noise is in the machine, I think it comes to HD. The curiosity was that I unplugged the power cable (while the power of the lamp was on) and start the laptop computer was! I wanted to do it again, but no luck. Only 2 times I managed to do that start this way, the switch sur-rien-> Switch/switch sur-rien-> by unplugging the power cord-> startup! I then tried to start a car boot CD Knoppix (linux), but after 10 seconds of loading linux screen went black again! Can someone help me? What could be? Battery? RAM? Wherer can I do a clear Cmos? It's very frustrating :-( Thanks a lot, greetings from Germany, Chris

  Hi Christian

  It's really easy to tell what the problem can be don t do you know if the previous owner had any problem?

  Is it possible to enter the BIOS settings? Try it by pressing the ESC key at startup to the top.

• Portege 4010 Bluetooth - connection for samsung and motorola phones probs

  I have a portege 4010 with bluetooth. I am trying to connect to our two phones - a samsung sgh-e370 (newish) and a motorola V600 (2 years). Both have BT I downloaded and installed the latest Tosh BT stack (4.0.something). Shows Device Manager four drivers of tosh in BT - all are OK. I have allowed the discovery and allow the connection on the tosh. I did the same thing on the phones. When I run the "Add new connection" Wizard on tosh, he finds two phones and they appear under the devices section in BT Manager with the names I gave them on real phones. However, neither picked up phone tosh and showed no tosh by asking the numbers of pins on the phones.

  The net result is I now two phones display in BT Manager, but if I click on is and choose use log I recover the error "connection failed".

  If I try to find the portege using the phone, the samsung it is but motorola doesn't have. I can't get the motorola to twin with the tosh - it just says "unable to pair up with the portege.

  Any help gratefully received.

  RJ

  Hello

  I don't really know what is the problem in your case, but I did this a few times with my Motorola RAZR V3 and it works fantastic. The whole was finished for 1 minute. I hope that you do it in the right order, but I am writing to you the steps I did:

  1 activate the Bluetooth using the FN + F8 key combination
  2. install the new hardware if necessary (some of them)
  3. start the Bluetooth stack
  4 turn on the Bluetooth on the mobile phone (discoverable)

  5. Select the Express mode > next
  6. choose visible device listed in 'Bluetooth device list' > next
  7 choose to identify passkey (1234)
  8. Enter the key in the mobile phone. Twinning will be success

  I did it on this path, and now I can send all documents in my Tecra. If you want to use as a modem, you must do this:

  1. after peeling going on Next and configure the internet connection
  (provider number) > finish
  2. the new connection will be created in the Bluetooth stack utility
  3. you can start the numbering with double click or click with the right button of the mouse and choose 'connect '.

• Portege 4010, HID not supported

  He finds the mouse OK but fail to complete the installation.
  I get "Human Interface Device (HID) profile is not supported in this configuration" when I try to connect my MS IntelliMouse Explorer for Bluetooth. I have the latest version of the software of Toshiba (SD) and battery on my Portege 4010. Using the USB MS Bluetooth dongle on another computer (of office) everything works fine.

  Hello

  Maybe this site will help you?

  http://APS.toshiba-tro.de/Bluetooth/

  There are troubleshooting costs and info.

  Bye Bob

• Portege 4010 - upgrade memory

  I have a Portege 4010 and cannot find the expansion Bay of memory to upgrade the memory. Under my laptop's hard drive battery, dvd and what I think should be the memory, BUT it has 2 wires attached to it.

  Hello

  Memory modules are hidden under the keyboard!
  You will need to remove first a plastic cover to think above the keys F1 to F12.
  Then you should find 2 screws holding the keyboard.

  Please be careful because the keyboard is connected to the motherboard with a thin flat cable

  Then, you could see the memory modules. Gently press the two latches.
  One end of the strip of memory expansion will pop up. Enter the module memory expansion, then take it out.

  I hope this helps...

• Upgrade memory on Portege 4010

  I want to upgrade my memory Portege 4010 and I know that I need 144 pins/PC133 SO - DIMM SD - RAM. Unfortunately I couldn't understand (in the same after talking to the Toshiba Austria), if I have to buy memory may be high or low density.

  Most of the memory at low prices on eBay is high density and I'm afraid to buy an incompatible.

  I hope that someone already has experience with it. It seems to be my last chance to get some relevant information.

  Thank you.

  As I remember for Portege 4010 maximum memory is 1 GB (2 x 512 MB) and no matter if you choose the version high or low density.
  If you need 100% guarantee you choose the version of low density.

• Portege 4010: How to install the cd - r or dvd - r?

  Anyone know if I can change the slimbay on my portege 4010 on a CD - R, or ideally a DVD-R?
  If so, what are the best places to get these?
  (I live in the United Kingdom)

  Thanks for your suggestions,

  Ian

  Hello

  I found the info this Portege comes with two discs. Readers are:
  Toshiba (SD-C2502) and TEAC (DV28E-B).

  I put t really know if any DVD-R/RW drive is compatible, but you can contact the Service of your country partner and ask them. They are usually updated hardware and should have enough experience.

  Otherwise, try to find a few upgrade for laptop shop in your country.

• Screen dirty on my Portege 4010

  My portege 4010 were grey marks on its screen for a while. I tried various screen cleaning fluids and they don't spend. They seem to come from the contact of the screen with the keys?

  How can I remove these, or if I can replace the piece of plastic that covers the LCD screen?

  Hello

  If you can't clean the screen with different cleaning fluids, it may be that those gray marks are not dirt but bumps!

  My suggestion is that if you don't clean it, you should contact a Toshiba Service partner (perhaps you warranty) and check it out! It may be that the teeth are caused by a keyboard set too high. This should be verified to avoid a higher damage.

  Goodbye Tom

• NO sound when recording Audio - problems with Windows 7 Ultimate 64-bit

  I got in trouble for almost a year now with NO sound when recording Audio with Windows 7 Ultimate 64-bit. I just found this forum today. It's really weird how recording with windows and other sound recorder works perfectly since 1998 or so until the upgrade to win 7. Now every time I try to record it shows no found recording device or just fails to record any sound. As you'll see below I have activated What U Hear so I can use the system recording features sounds.

  I use the functions of audio recording and pdf reader because I'm legally blind. It is one of the few tools that I could use with ease on all my systems windows for many years.

  A similar question has started happening with nvidia graphics cards. AND... I was led to believe that it was a problem with Sony wanting more strong piracy measures built into windows. Am I correct to assume that this is what is happening with the sound also today or is there a solution to this frustrating problem?

  I run a dxdiag & posted that, according to me, you asked another user on the forum, the same or similar problem.

  Help solve this problem would be greatly appreciated as this has been a problem for quite a while now.

  ------------------
  Information System
  ------------------
  Time of this report: 07 25, 2012, 19:06:02
  Computer name: RAIDER
  Operating system: Windows 7 Ultimate 64 - bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120503) - 2030
  Language: English (regional setting: English)
  Manufacturer: Gigabyte Technology Co., Ltd..
  System model: P67A-UD3-B3
  BIOS: Award BIOS v6.00PG Modular
  Processor: Intel Core i5 - 2500K CPU @ 3.30 GHz (4 CPUs), ~3.6GHz
  Memory: RAM 8192MB
  Available OS memory: 8176MB RAM
  Page file: 2861MB used, 13487 MB of available space
  Windows Dir: C:\Windows
  DirectX version: DirectX 11
  DX setup parameters: not found
  DPI setting: Using System DPI
  System DPI setting: 96 DPI (100%)
  DWM DPI Scaling: disabled
  DxDiag Version: 6.01.7601.17514 64 bit Unicode

  ------------
  DxDiag Notes
  ------------
  Display 1 tab: No problems found.
  Sound tab 1: No problems found.
  2 Audio tab: No problems found.
  Input tab: no problems found.

  -------------
  Sound Devices
  -------------
  Description: SPDIF Out (Sound Blaster X - Fi Surround 5.1 Pro)
  Default audio playback: Yes
  Default voice playback: no
  Hardware ID: USB\VID_041E & PID_30DF & REV_0100 & MI_00
  Manufacturer ID: 65535
  Product ID: 65535
  Type: WDM
  Driver name: ksaud.sys
  Driver version: 6.00.0001.0460 (English)
  Driver attributes: Final retail
  WHQL Logo would be: n/a
  Date and size: 2010-07-30 11:35:08, 1588608 bytes
  Other files:
  Driver provider: Creative Technology Ltd.
  HW Accel level: basic
  Cap flags: 0x0
  Min/Max sample rate: 0, 0
  Static/Strm HW Mix beef: 0, 0
  Static/Strm HW 3D steers: 0, 0
  HW memory: 0
  Management of the voice: No.
  Listen/Src/EAX (TM) 2.0: No, no
  Listen/Src/I3DL2 (TM): No, no
  Sensaura (TM) ZoomFX (tm): No.

  Description: Pregnant (Sound Blaster X - Fi Surround 5.1 Pro)
  Default audio playback: No.
  Default voice playback: Yes
  Hardware ID: USB\VID_041E & PID_30DF & REV_0100 & MI_00
  Manufacturer ID: 65535
  Product ID: 65535
  Type: WDM
  Driver name: ksaud.sys
  Driver version: 6.00.0001.0460 (English)
  Driver attributes: Final retail
  WHQL Logo would be: n/a
  Date and size: 2010-07-30 11:35:08, 1588608 bytes
  Other files:
  Driver provider: Creative Technology Ltd.
  HW Accel level: basic
  Cap flags: 0x0
  Min/Max sample rate: 0, 0
  Static/Strm HW Mix beef: 0, 0
  Static/Strm HW 3D steers: 0, 0
  HW memory: 0
  Management of the voice: No.
  Listen/Src/EAX (TM) 2.0: No, no
  Listen/Src/I3DL2 (TM): No, no
  Sensaura (TM) ZoomFX (tm): No.

  ---------------------
  Sound Capture devices
  ---------------------
  Description: What you Hear (Sound Blaster X - Fi Surround 5.1 Pro)
  Capture audio by default: Yes
  Default voice Capture: No.
  Driver name: ksaud.sys
  Driver version: 6.00.0001.0460 (English)
  Driver attributes: Final retail
  Date and size: 2010-07-30 11:35:08, 1588608 bytes
  Cap flags: 0x0
  Format flags: 0x0

  Description: Microphone (Webcam Pro 9000)
  Capture audio by default: No.
  Default voice Capture: No.
  Driver name: USBAUDIO.sys
  Driver version: 6.01.7601.17514 (English)
  Driver attributes: Final retail
  Date and size: 2010-11-21 13:23:47, 109696 bytes
  Cap flags: 0x0
  Format flags: 0x0

  Description: Line-In/Mic-In (Sound Blaster X - Fi Surround 5.1 Pro)
  Capture audio by default: No.
  Default voice Capture: Yes
  Driver name: ksaud.sys
  Driver version: 6.00.0001.0460 (English)
  Driver attributes: Final retail
  Date and size: 2010-07-30 11:35:08, 1588608 bytes
  Cap flags: 0x0
  Format flags: 0x0

  Hello

  In Services, verify that the Windows Audio service is running and set to automatic.

  a. Click Start and type Services and press ENTER.

  (b) ensure that these services are defined accordingly.

  c. right-click the service, and then click Properties.

  According to the DXDiag, there is no default sound capture selected.

  Description: Pregnant (Sound Blaster X - Fi Surround 5.1 Pro)
  Default audio playback: No.
  Default voice playback: Yes

  Description: What you Hear (Sound Blaster X - Fi Surround 5.1 Pro)
  Capture audio by default: Yes
  Default voice Capture: No.

  Description: Microphone (Webcam Pro 9000)
  Capture audio by default: No.
  Default voice Capture: No.

  Description: Line-In/Mic-In (Sound Blaster X - Fi Surround 5.1 Pro)

  Capture audio by default: No.

  Default voice Capture: Yes

• Hard drive with the Portege A200 problem

  I just bought a Portege A200 a few months previously and recently noticed the hard drive starts to make noise 'rough '. Anyone can:
  (1) advise what could be the problem, or is this normal?
  (2) to recommend what is the best way/tool/program to check the State of fitness of the hard drive?

  Thanks for help. Very happy.

  Specifications:
  Portege A200; 60 GB; Window XP Professional

  Post edited by: ccm76

  Hi ccm

  In my opinion, the HARD drive should run pretty quiet. You can still hear sounds, but they should not be strong. If the unit is a new brand, you must contact the partner in your country, and they can check if there are a few HARD drive malfunction. If it is necessary to change something, the warranty will cover all costs.

  Hi stan

  Sorry, but you should be smart enough to know that this kind of information is not for advertising. On this way, each stolen unit can be started. The best solution is to contact the Service partner and they can remove the password.

  Good bye