SP3 problems after download computer does not start normally in SafeMode only

Similar Questions

• My computer does not start. It beeps only

  I have a Dell Inspiron 531 Desktop, which is about 4 years old. The second that I turn it on it starts to beep. It will emit 2 beeps quickly then pauses about 3 seconds then beeps 2 again and keeps going.  It doesn't even come close to leaving. The monitor is not even to get a signal. It doesn't even come close to getting the boot menu. What it can be and what I can do?

  Here's how to diagnose boot beep codes: http://pcsupport.about.com/od/nonworkingcomponent/ht/beepcodestb.htm#.  This means that there is a hardware problem with your system.  If you analyze the codes, you will be able to determine which device is causing the problem.

  In the end, you certainly need to replace a unit of material (if you can figure it out on your own) or take the computer home at a reputable repair shop computer (or send it to the manufacturer for service - according to what is less expensive or makes you more comfortable).  This isn't a software problem, and given the circumstances, we would be quite unable to help even if also a software problem had thus given the lack of access to the computer.

  Unless you know what you're doing, I you suggest to take in service, diagnostic and repair or replacement (or decide it's time for a new computer).

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• Computer does not start after running the utility Boot Lenovo.

  Hello
  I replaced the power supply with a CX550M of Corsair, increased memory by exchanging the 4 GB to 8 GB for a 16 GB total, I added a hybrid 2 TB Seagate HDD and all worked fine until yesterday, about 1 month.
  Yesterday, I decided to run all the tests of the Lenovo startup disk and after that I restarted, the computer does not start.
  When I press the power button, the fan starts and it stops after 3 or 4 seconds and nothing happens, the monitor says no signal, I removed the external USB disk and printer, I reoved the second drive and the same thing heppens.
  Any idea what this problem could be? Would it be a bad power supply?
  Thank you

  Mario

  Resolved, I erased the memory CMOS, moved to following ankle boot, back up the cmos.

  Thank you

• You can save a broken computer? My computer does NOT start after the blue hp screen.

  In the past months, my computer has been the object of a freezing randomly, and Ctrl + Alt + Delete does not work. I stopped him via the power button. Sometimes, when I start it again, the computer moniter shows nothing but a black screen and the computer sounds different when it starts normally. When this happens, I turn it off again hit the left side of the desktop and turn on again. Whenever I do this, the computer starts normally, and I go on the computer use.

  Yesterday morning, after a break of 2 days, acess my computer and it is random freezing thing once again. I force close down as one normally do, and the computer does not start and displays the same black screen and the same fan/air weird sound. I stopped him and I hit the side RIGHT this time, I think and when I turn on the computer, the usual blue HP screen appears with the establishment, boot, diagnostics and system recovery things. HOWEVER, after this screen, a black screen will appear with this weird blue symbol on the upper left corner, I have never seen this and it looks like a circle with a triangle and a Pentagon below and it remains essentially on this screen forever. When I try to hit the establishment, boot, diagnostics and the shortcuts to system recovery, on the lower left side of the screen, it says "Menu boot loading...". ' or whatever the shortcut of loading represents, but nothing ever happens. When I press the other keys, this tapping noise comes from the computer at each tap of the keyboard.

  I have no idea what to do, and at this point, my first priority is to save important files on the computer. Does anyone know what is the problem? I want her more than a problem of system rather than a virus problem because refusing the boot black screen thing lasts for years. My computer is 3-4 years. I enclose a sketch of what looks like the weird symbol.

  

  MY COMPUTER WORKS NOW!

  With the flash drive, I was able to access the BIOS, which before, I couldn't.

  Eventually my computer was in some strange sort of lockdown setting, I switched it back to activate and now its work! I remember save important things in the future. Thank you very much for your help!

• Computer does not start after installing a new graphics card

  I am owner of a HP Pavilion H8-1020 with a processor intel i7 - 2600 s Windows 7 and am trying to upgrade my Radeon hd 6570 to a Gigabyte AMD Radeon R9 280 OC. I improved my diet for a Corsair CX750 to meet the requirements of power and installed with number. After the installation of the new card, which as far as I can tell is well seated in the pci slot and correctly connected to the PSU, my computer does not start.

  System powers on, all fans of begin to run including the fans on the new graphics card, but it does not begin the boot process, no entry is received at my monitors, no light on the keyboard, my OS starts loading, I can turn off the system without the delay that will flow normally. Then I reinstalled my old graphics card and the computer started as usual.

  Now, assuming that the card is not DOA, which unfourtunatly I have no way to verify, and I'd like to see if it could be another problem before going through the process of restitution. I did some reading on the internet, which helped, but did not help for a technological neophyte like me.  Now, I know a few things that could cause this problem but lack the necessary skills to determine what question is making me. What I've read, these could be possible questions:

  1: my new graphics card is not compatible with my motherboard. It's something I know now that I should have checked before buying and something I should theoretically be able to do it now, but I am at a loss on how to do it. My card is compatible with my motherboard?

  2 could be a BIOS problem. I updated my bios driver with the version provided by the HP site. I am running FRIEND 7.16 05/10/2011.  And from what I've read it might have something to do with my bios to UEFI mode and I would need to go to a legacy mode so he can recognize a new device, is it true? I am extremely wary of messing with my BIOS settings for fear of bricking my system. How can I check my current BIOS settings are and what I should change and how would approach I change them? Will one of these changes affect my system if they are not what is not causing the problem?

  In addition to these issues, anyone know any other matter which may be the cause of the problem that I should look for? Thanks for any help.

  Hello @Eric_Z,

  I can see why you are having problems with your new graphics card, and to get to the fast response that your motherboard is not compatible with the new graphics card that you have purchased. And here's why.

  Your motherboard according to the page HP Pavilion HPE h8-1020 Desktop PC product specifications is the Carmel motherboard, which has the following expansion slots:

  • A PCI Express x 16
  • Three PCI Express x 1 connectors
  • A PCI Express Mini Card x 1

  As there is no version indicated for your PCI Express x 16 it slot means that it is version 1.

  Now, your previous graphics card was a PCI Express 2.1 x 16, which means that it was version 2 and compatible with your PCI Express x 16 slot on your motherboard. However, the new card is PCI Express 3.0 and will not work in your motherboard due to a compatibility break. While the technology is supposed to be compatible there are many cases where it is not, and I'm afraid that you meet one of these cases.

  I am offering an overclock.net article entitled: the final answer to the controversial compatibility of PCIe x 16 version. where your situation has been tested and examined.

  I hope this helps. Have a great day and thank you for display on the HP Forums!

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• I deleted the boot camp trying to resize the hard drive on my mac pro book. now, the computer does not start without a bootable device, which I don't have, and any download must be on a windows machine. Can anyone help

  I deleted the boot camp trying to resize the hard drive on my mac pro book. now, the computer does not start without a bootable device, which I don't have, and any download must be on a windows machine. Can anyone help

  1. did you remove Bootcamp using disk utility?

  2 have you tried local restore or recovery of the Internet? - OS X: on OS X Recovery - Apple Support . Mac with built-in optical drives may need 'Gray' disks to boot the system.

• Computer does not start after installing new graphics card

  HP-envy h8-1503
  I7 - 3770 k 3.5 GHZ
  10 GB of Ram
  Windows 8.1
  
  I tried to install a new edition of diamond Raedon 7770 to replace my old 7570 and when I try to start the computer I get 6 long beeps and the power light flashes 6 times. Everything is plugged in right and the video card turns on. It will not be output to the screen tho and the computer does not start!

  I fixed it, the problem was the safe boot in my bios, when I disabled the system booted and worked perfectly since! Thanks for the advice tho!

• Compaq 6200 PRO MT: Makes the computer does not start after upgrade CPU

  I have the HP Compaq 6200 PRO PC of MT 615114-001 motherboard and processor Intel Celeron CPU (LGA 1155). After I changed the CPU for Intel Core i5 (LGA 1155) computer does not start. He begins a minute (less than one second) and stops again. No beeps. After you have installed the Celeron back everything works fine. i5 CPU is brand new. What can be?

  In my previous post, I explained the reason it has not worked, and listed the CPU that will work.

  HP tests CPU in the laboratory and publishes a list of processors that will work in a notebook.

  Notebook motherboard BIOS has a list of processors that will work. If it is installed, which is not encoded as OK in the BIOS ROM file, then this will not work.

  Processors published (in the maintenance guide & Service for your nttebook series model) are available in models that can be deilvered in State CTO (configured to order).

• computer does not start after the installation of vista updates.

  computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

  Hello

  Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

  Hope that information was useful

• M127FW MFP: Computer does not start after the installation of the MFP M127FW

  My computer does not start on my hard drive after installation of my new printer MFP M127FW unless I have first of all disconnect the USB cable between the printer and then turn on the computer.  My BIOS is set to boot from my drive hard, not from a USB key, so that makes installing the drivers M127FW MFP and software do on my computer?  I guess it has something to do with the Smart Install feature.

  "On the printer, press Setup, maintenance, Smart Install and stop."

  It worked.  Thank you.

• computer does not start after installing video card

  I, m new here so please bear with me.  I have a PC HP Pavilion Media Center TV (m7434n) I'm trying to replace the video card (Nvidia GeForce 6200SE with Turbo Cache) in. I am trying to replace it with a Nvidia EVGA 8400GS. I delete all the nvidia drivers, make sure that the pci-e card is used in the implementation. I have then to remove the old card and install a new one. When I try to start the computer, fans turn on but that's all.  There is nothing on the monitor.  The computer does not start. I replaced the power supply bestec 300 watts with a new antec brand 430 watt power supply.  When I reinstalled the old video card, the computer starts ok. I tried to replace the video card with an ATI Radeon HD5550 too and it's the same thing (the computer would not start), reinstall the old card and it starts up fine. Any help would be greatly appreciated.

  Gary,

  You may have a compatibility issue with the ATI HD 5550 and 2006 PC model.  I've seen other posts where ATI 5xxx video card did not work in older HP PCs.

  When you are referring to the installation of the older video card do you mean going back to the integrated video card?  Moving the video cable to the card installed?

  Install the NVIDIA 8400GS and connect the video cable. Now follow the instructions for clear the CMOS.

• Error - NTLDR missing Windows XP Home computer does not start.

  Original title: XP-based computer does not start.

  XP Home does not start after I uninstalled a large file of Samsung mobile phone. I get a missing NTLDR error message and have had a System32 error as well, but there is no DOS prompt that would allow me to access anything whatsoever. Another problem is that I lost my installation CD. I initially bought this Dell PC nine over 6 years ago, so can provide identification details, if necessary program. Could someone tell me how I can make a recovery CD please? (No floppy drive not installed in the PC). To further complicate things (Yes, I know - I created many more problems that we all need), I have to keep my files on the hard disk, so cannot do a complete reformat, unless someone can tell how to save them somehow. My BACK skills could be summed up as "plodder inexperienced but determined!

  The file might be missing or it could just be that XP can't find it if your file system has somehow got corrupted.

  As the forums MS Answers does not prompt for any information system when a new question is asked, we know absolutely nothing about your system.

  Not knowing the basic information a problem prolongs the frustration and the agony of these issues.

  Provide information on your system, the better you can:

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Your system have IDE or SATA disks?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  System32 error, you see, is what exactly?

  Depends on a few factors, there could be another copy of the file NTLDR in other places on your system, but you have to start on something to find out whether there is or not.

  After answering the above questions, I begin to make a CD from Recovery Console bootable XP by running a chkdsk/r, first on your HARD drive and then see what is left to do.

  Here's how:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and don't forget (no support for XP not necessary).

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD (do not install UniBlue or the Ask Toolbar - never!):

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• My computer does not start. I'm a WMILIB. SYS 0XC000000F

  My computer does not start. I tried to launch the operating system disc and after following all the steps, I get a message saying "Windows failed to load because a required file is missing or corrupted" and then it gives the file, WMILIB.»» SYS and status 0xc000000f. Startup Repair tried several times and it always comes back to this message. I can't start to try anything. Can I do to solve this problem?

  Hello BonnieSmith,

  Instead of choosing the system repair, we will choose the system restore and see if there is a restore point that exists before this behavior.

  Best regards

  Matthew_Ha