Spa 232d + spa302d

Good afternoon, community. I bought a set of SPA302DKIT-G7 (Dect phone and adapter to connect on it for SIP). Configured SIP accounts. Outgoing calls work, but incoming calls are not. Web access adapters I see "line 1 status, call 1 report: ringing"when I have a call, but the call is not transferred to the handset. " The tube connections are inbound and outbound number. Any idea why this might be?

I have no SPA232D here now, but line 1 is the analog line, not the handset DECT, isn't it?

So it looks like a bad configuration - incoming call is routed to the POTS line. If you want to be sent elsewhere (for example, an individual combined DECT), you need to configure it accordingly.

Unfortunately, you did not describe the scenario of default so it is so difficult to give more specific advice.

Tags: Cisco Support

Similar Questions

  • Cisco SPA232D ATA and Cisco SPA302D Wireless roaming handset

    I read the documentation of SPA 232D and I see that it supports up to 5 stations 302D SPA.

    In this project, I have 4 floors and we need a total of 15 phones:

    3 - basement

    5 - ground

    4 - first floor

    3 - second floor

    When the person is using the basement 302D phone have no reception when they walk on the upper floor.

    Can we do roaming between 232D? Is it possible to interconnect their? The range in the documentation may not be enough.

    What would be the recommended Cisco solution for this, we want to use DECT.

    Range: Indoor: 165 ft (50 m). Outdoor: 980 ft (300 m)

    Thanks for thinking of the spa232d for this project,

    Unfortunately with the current firmware it does not support combined roaming between base stations.  There is not an easy way to transfer between units handsets (you must unsubscribe from a base station and register again with the 2nd spa232d).

    The distance of the datasheet is optimal in a perfect environment, and I expect to be a little less real world.

    I woud suggest get a spa232d and a spa302 (maybe a dealer demo unit) and test range on the customer site.  Basically, do a site survey to see where the best place in the unit.

    If you need more 5 units on a floor, or signal will not reach both ends of the beach, 2 - spa232d devices may be necessary.  Some devices would be recorded to one, some to the other.

    There is good documentation on configuration and management with the device calls here.

    SPA232D & SPA302D: Introduction to the call routing scenarios advanced

    https://supportforums.Cisco.com/docs/doc-30269

    Let me know if you have more questions.

    Dan

  • now net.framework 2.0 spa 2 & 3.5 sp1 are not up-to-date.

    Original title: incident #SRX1156346212

    now net.framework 2.0 spa 2 & 3.5 sp1 are not up-to-date. Sorry for the delay to return to you, the first problem that still exists. Thanks again for any help. Michael

    Hello

    1. you receive an error message when trying to install these updates?
    2. What is the first problem are you referring to? Previous post the link to the thread.

    You can try to download and install the updates using the links below.
    http://www.Microsoft.com/download/en/details.aspx?ID=1639
    http://www.Microsoft.com/download/en/details.aspx?ID=22

  • help with SPA 3102 (question graphcal)

    HI guys here is my situation (I draw so it would be easier for future reference):

    I want to pick up A phone and dial the Ext 101 101, 102 for Ext 102 and so on.
    also, I want to put routed my call for location 2 location 1 for example transferring calls to 104.

    any help would be really appreciated even a starting point as for example the configuration of spa to route my call not NAT, so it can connect to the other.

    castro69 wrote:
    also, I want to put routed my call for location 2 location 1 for example transferring calls to 104.
    any help would be really appreciated even a starting point as for example the configuration of spa to route my call not NAT, so it can connect to the other.

    I guess that's an analog PBX, otherwise you wouldn't need the SPA3102 through the internet.

    For communications between the SPA3102, I would use direct ip call, using the external ip address and the sip port numbers.  Think that the SPA3102 is two separate cards inside the box where treat you everyone with its sip port number added to the external ip address common.

    I would setup port sip distinctive numbers on each of the baths to keep things straight.  You have a number of separate port for tabs of line 1 and line PSTN.  You will need to send these to the SPA3102 adapter port numbers in their respective routers or firewall of the router will reject incoming packets on the internetI would also convey the port range rtp for voice, flow packs.
    On each tab of the line 1 and RTC, you define NAT Mapping Enable: YES, not record, make call without Reg Yes, years call without Reg No. I put your external ip address on the Sip tab under EXT IP.  This will tell the SPA3102 to use this address in the sip signaling. I assume you are using static external ip addresses.   On each tab of the line 1 you would activate IP Dial Yes.

    The analog PBX is connected to the FXO port on one of the Spa.  You should check the voltage level hung up and won and then set the line parameter usage on the RTC of the SPA line tab to halfway between the two readings.  You can read the levels of tension on the PSTN line tab.  Calls to the PBX of the PSTN line tab will go through the voip to PSTN gateway.  I set up the catwalk with http authentication and configure a user name and password.

    Details are starting to become quite complicated.  I'd get running through steps.  Get a job step before moving on to the next step.

    The 1st step would be to get A phone call/receive calls to a PBX.  You can configure the line 1 for FXS phone attached A to use port location PSTN 2 as the proxy using http authentication, and you can then dial the extensions you want to call.  Location 1 SPA3102 will send a guest of the sip Protocol to the tab location 2 SPA3102 from pstn line and the SPA3102 will dial the number on the FXO port to the PBX.

    For calls coming from the other direction of a PBX to slot 2 SPA3102 the only place where you can connect a voip call is in the SPA3102 numbering plan.  If you want to call only phone that is easy, install you just dialers-messengers automatic telephone in the pstn-to-voip dial plan.

    I'm not clear about what you want to do with phone B I take is Extension 104.

    I like your designs.  Can save a lot of words.

  • Where is the firmware for 1001 SPA?

    I have a SPA 1001 (which I have used since 2005), but it still has firmware version 2.0.10 (e)!

    Where can I find the newest firmware AND software that downloads the firmware on the device?  I am able to find a .bin on a site file in the CZ, but no charger.  My SPA refuses to download the software itself via the configuration option.

    Thanks in advance.

    I managed. The SPA-1001 firmware fles (all found) are uploaded to RapidShare as an archive (26 MB):

    http://rapidshare.com/files/305539534/Spa-1001_FW.zip

    Most of the FW are both .bin as .exe installers.

    Versions within the archive:

    Relase FW: 2.0.13seg, 3.1.8SE, 3.1.17SE, 3.1.19SE

    Beta FW: 3.1.9SE, 3.1.10SE, 3.1.12SE, 3.1.16SE

    My Favorites: 3.1.8SE, 3.1.19SE (the one I'm currently using on both of my devices SPA-1001)

  • SPA-3102: unable to connect to the SIP server

    Hello

    We have a SPA-3102 installed and work properly in our US Office. We are trying to install another one in our office in India, but we cannot get this device to register with the SIP server.

    This device works perfectly when try us two different residences here in India with two different providers. But when we try to our office with a third party service provider, it is impossible to save.

    The internet connection at the office from the East through an ADSL router which is mode bridged with two IP static coming out of it. We are able to have access to the internet for our PC through this SPA-3102, but the SPA itself is unable to register with our SIP server. We use a Gizmo5 SIP server.

    The same parameters were working in our offices in the United States and two different residences in India but does not work in our office. I don't think that the ISP here has nothing to do with this problem. Would be - this works the ADSL router in bridge mode? Can I make changes in the settings of the SPA to work around this problem?

    Any help is appreciated.

    The problem could be the firewall or the router, but it is also possible that your Indian ISP is blocking voip connections.  It was reported that is not unknown in India.  Sometimes this type of blocking is done by throwing packages for voip standard sip signalling port 5060. You can easily change the SIP port in the SPA3102 to traffic returning to the SPA packages and in fact routers often changes the port without your knowledge, but packets destined for voip provider must use the port specified by the provider number.  Since you can access the internet with your pc, I would try to run tests to see if this is the case.

    I ran a few ping tests and tests to see if I could save with other providers or services that use replacing or other sip signaling ports.

  • SPA-3102 PSTN idle status, will not answer but watch sounds.

    Greetings,

    I am a complete newbie in the world of voip. I have an spa3102 and a computer virtual trixbox. When I use my softphone to compose, it makes to the spa3102 (shows the id of the last and gives a status of the appellant voip 'reply') but I get an "all circuits are busy now" and does not change the status of IDLE pstn. It also will not answer the phone for incoming calls to the PSTN.

    Outgoing stuff could be a problem of numbering plan (don't know not just guessing) here it is:

    (S0:xx. <@gw0>)

    I tried the regular (or default) (xx).

    incoming calls are supposed to go to a handset on my desk, for example ext 101 is the dial plan: (S0:101@internalip)

    I can't see the forest for the trees. Can someone give me some advice on where to look. I'm completely puzzled by something non-response externally, and why I get a all circuits are busy if there are inactive on the status page.

    an interesting note: If line1 is connected to an analog phone, it will dial a number, but always shows failover for a reason any...

    Thank you very much!!!

    Greetings!

    Thanks for the reply. I do not know if I explained properly (sounds like I don't have). I have a trixbox and I use the SPA in interface with my RTC and I want to have a fax machine (but later) on the FXS port. The problem I have is that I could not field calls to the collection. They would just ring and ring. I thought it was a dial plan (and hope it was not a hardware problem), but he just wouldn't answer the phone. He would show 'Ringing' like the PSTN status, but Voip would be "IDLE". I've been pouring through the guide of the administrator, forum messages for about 2 weeks now.

    But I didn't know what the problem was. The spa3102 is waiting until she can establish a connection (with the internal phone system) until it meets the PSTN. This is why it continues to ring. The problem why it shows it is inactive and (even with enabled full logging to a syslog box) no traffic to SIP the trixbox internal... because I had the port internal plugged in... not the WAN port (or internet). Thats right... silly me...

    I gave the wan port an address on the same subnet and moved the cable to it, once I could talk to her I change address internal to something even not on my network (if no routing problem) and left the network adapter disconnected (internal nic). Then I changed the wan to the old internal address address (trix trunk was already configured in this ip address anyway...) and PRESTO! I tried calling the number RTC and started to receive log entries showing the sip signaling and he's trying to route the call to the box of trix. It works now! So he was not answering the phone in my case, because it could not connect to the pbx or the ip phone and that because I don't use the WAN/INTERNET port on my SPA. Something I don't remember seeing in the textbooks as a "hafto' or a 'must '... I might have forgotten that of course, but I don't remember seeing him there.

    So if you enable logging, and then call this number (I used the PuTTY and 'tail-f /var/log/spa3102.log"to see the entries that they light up the box of syslog) and you don't see any sip traffic, it could be that you must use the WAN/INTERNET port instead of the internal port apparently logical... BE sure THAT ENABLE YOU REMOTE ADMIN if you decide to give it a shot.

    Also you can do the spa to answer the phone, even if it has no where to send the call (or if you want incoming people to use a PIN) on the GATEWAY PSTN - VOIP, there is a setting "off hook during the VOIP call" (default = no), but change that Yes - he would answer... and then sit there... If I had a PIN with a dial plan that is associated with this would give a fast busy after the entry of the PIN. BUT now everything is cool!

    Thank you!

  • SPA-3102-backup/restore settings?

    Hello

    Is there a way to backup/restore the settings to a file in the SPA-3102 router?

    ASE

    There are several ways to save the settings of the SPA3102 according to some forums - check links ff

    http://forums.whirlpool.NET.au/Forum-replies-archive.cfm/756454.html

    http://Forum.Voxilla.com/Linksys-Sipura-VoIP-support-forum/SPA3102-compiler-configuration-backup-Mon...

  • SPA 3102 Admin Guide

    Where can I download the administrator for the Linksys SPA 3102's Guide?

    I don't remember how many times I tried to find such a link and how many hours I have spent so far with it. I could find answers to this question, but the links are no longer valid.

    Thank you for your help.

    Try this link.

  • Problem with Instalation 900 SPA

    Hi all
    I am about to install a new VOIP system in our offices.  We are only a small office, but reasonably busy and I only need three to five extensions.  I already have the material and I'm reasonably confident (famous last words!) by installing the system with a SIP line and connected to a normal telephone line for the downturn.  I'm NOT sure about a field.  Prime material

    SPA9000
    SPA3102
    962/942 SPA phones

    OK now my desktop system consists of a server with SBS2003 with NIC TWO one for LAN and WAN cards.  Workstations and other elements are connected by ethernet to a D Link switch which is connected to the NIC1 and the NIC 2 connects to a telephone line Draytek router/ADSL broadband.  Internet access is of course provided to workstations using DHCP.  Everything works well at the present time.

    Now that I do not understand is the SPA 9000 connectivity and the SPA3102 which has an FXO port to the telephone line.  As I don't have only one telephone line how to connect theat line to the router AND the SPA3102.

    I hope that explains my question

    Thanks for any help

    You will connect the WAN port on the SPA9000 to the switch and then together "Network Interface Proxy" WAN under the label to join automatically, in which case your SBS2003 has no problem handling of multicast SIP, IP of SPA phones. You must manually register the SPA3102 to the SPA9000, you set a proxy which is the IP address of the SPA9000, you can verify that proxy address by clicking on one of the IP phones that automatically, then you put a User ID user defined. You can test if it works by calling locally and User ID on one of the IP phones.

  • SPA 2102 back 10 MB support

    Hello

    I have ADSL 10 MB when I connect wrtp54g and I test the speed with the speed of download of this http://speedtest.vonage.com costume is always about 9980 kb/s and 988 Kbps in upload is but when I connect SPA 2102, I always get the download speed on 6760 to 7010 Kbps in upload is even 988 Kbps if I disconnect SPA 2102 and connect wrtp54g I'll be back as the download speed 9980 Kbps and upload is 988 Kbps

    What is the problem with SPA 2102?

    Thank you

    Thanks for your replay

    But when I put the SPA2102 behind the sound quality is not the same when one computer that downloads why I buy the SPA2102 be before the router.

    By the way, my wireless router is Linksys WRT54GX Firmware Version: 1.02.15 

    Le WRTP also is phone adapter, but the problem with this one, it's still drop off the internet that's why I decide to replace it with SPA2102

    Thank you

  • Original SIPURA SPA 3000 help

    Five years ago, that I bought, directly from SIPURA, a new SPA-3000. I've never used but now I want to set up, but I want to make sure it has the latest firmware. I looked at the Linksys site (because any attempt to access www.sipura.com is redirected to Linksys) and found the firmware for the SPA-3000. Can someone tell me if this is the same unit as mine or changed from the original and the firmware does not work on mine?

    I tried to contact Linksys technical support, but their automated system tells me that I need to contact the dealer, who ironically is Linksys, since they bought Sipura. When I get to a real person that they just repeat that I have to contact the dealer of origin, they won't listen to me telling them that they are now the dealer.
    Can someone help and tell me what is the latest version of the software for this device and where I can download it? The configuration GUI displays the following information:
    Software version: 2.0.13 (GWg)
    Hardware Version: 2.0.1 (7067)

    Thank you

    Hello bsdaiwa, Yes this is the same unit. SPA-3000 has never really produced by Linksys, they later produced SPA-3102 units. Anyway, regardless of the producer of the unit (SPA or Linksys), they are able to use the same firmware.

    I myself have 2 pieces of SPA-1001 units, the 'old' box of Sipura, Linksys 'new' box, each of them having different revision HW and the two hapily run the same firmware 3.1.19 (SE) Linksys pages.

    Also, the SPA-xxxx units are protected from the flash of the incompatible firmware (for example from a different camera model), unit load the firmware first to the RAM, then check the "signature" FW, and that if it is the corresponding FW "signature" then unit flashes it it's rom flash and reboot.

  • SPA 112 - make calls over WIFI between the lines?

    Dear community

    You just bought a SPA 112 which seems to work very well, except for one thing:

    We do not seem to place calls between them the two lines (long cable between two buildings).

    It sounds but is silent and hang up after making a call and end up on the other side. Any chance of a hint?

    Also curious to know if I need to put something specific for use in Sweden? Seems to work very well, but still.

    Do I edit something else? The dial plan?

    Thanks much for any help!

    Jan A.

    1. What is the long cable? What is the cable type (disclose AWG or diameter).

    2. turn on the syslog & debug (highest level) and catch them. It can help to analyze the issue.

     if I need to set something specific for use in Sweden
    According to your wishes. Your username cannot be content with US progress tones or ring US. You can configure some more appropriate for the Sweden , if you wish. Ring voltage waveform, and frequency of the ring should be configured according to your needs of end-phone. Plan of the PBX the SPA112 is saved as well as the requirement of the user of numbering Plan numbering must follow. There is nothing like "a suitable configuration requirements" plan of numbering - even for a given country, including the Sweden.
  • UCS 540 and SPA 112 ATA

    Hello community support!

    I have a UCS 540 and want to connect analog phones via SPA112 ATA. Unfortunately this combination is not officially supported, but several positions indicated that it is possible.

    If someone has an idea or a solution that would be greatly appreciated!

    The SPA gets it's IP address via DHCP from the UCS and points to the NVI UCS interface IP as proxy. the IP Address of the ATA is to ping requests.

    Thank you

    Mike

    You're right, they are not supported.  You can configure most likely that SIP phones in the WEC, but I have never seen an example of configuration of it.  You can start here is how to set up a phone SPA in a WCF router using the SIP.

    http://www.Cisco.com/c/dam/en/us/products/collateral/unified-communications/Unified-Communications-Manager-Express/spa_polycom_application.PDF

    Let me repeat that you won't get any support from SB - TAC for this.

  • Configuration of slow appeal for all SPA on UC560 phones

    Hello world

    Our client (and I) complains about slow call setup when you make outgoing calls from phones on UC560-BIS-K9 SPA.

    The user type the called number and push button dialing on the phone and it takes about 10 seconds for the call to go to SIP trunk. I checked with"ccsip debug messages"and it's true.  10 seconds after pressing the dial button I can see Debugging has started and the call out via sip trunk instantly.

    Telephony-service we created interdigit timeout to 5 seconds, still no improvement.

    It is the configuration of counterparts:

    !

    Dial-peer voice voip 500

    Description * PROVIDER - Peer *.

    translation-profile incoming IN_FROM_PROVIDER

    translation-profile outgoing OUT_TO_PROVIDER

    destination-model 0 t

    session protocol sipv2

    session target sip-Server

    session udp transport

    incoming called-number

    codec voice-class 1

    profiles of sip voice-class 1

    DTMF-relay rtp - nte

    rate of Fax 9600

    Fax g711alaw transmission protocol

    No vad

    no additional service moved temporarily sip

    !

    Even when you use abbreviated, the user does not know if the call was launched.  After pressing the speed dial user must wait 10 seconds (with empty phone screen) for phone show the call on the phone and only after 10 seconds, the user gets information that the call is being tone and having the status of the call display - it's even more painful for them.

    I also close the BRI ports, still no progress.

    We hope to get some feedback on it,

    Kind regards!

    You must configure a perfect match for the numbers dialed, not using T destination-model.

Maybe you are looking for