SPA 3102 Admin Guide

Where can I download the administrator for the Linksys SPA 3102's Guide?

I don't remember how many times I tried to find such a link and how many hours I have spent so far with it. I could find answers to this question, but the links are no longer valid.

Thank you for your help.

Try this link.

Tags: VoIP Adapters

Similar Questions

  • SPA-3102: unable to connect to the SIP server

    Hello

    We have a SPA-3102 installed and work properly in our US Office. We are trying to install another one in our office in India, but we cannot get this device to register with the SIP server.

    This device works perfectly when try us two different residences here in India with two different providers. But when we try to our office with a third party service provider, it is impossible to save.

    The internet connection at the office from the East through an ADSL router which is mode bridged with two IP static coming out of it. We are able to have access to the internet for our PC through this SPA-3102, but the SPA itself is unable to register with our SIP server. We use a Gizmo5 SIP server.

    The same parameters were working in our offices in the United States and two different residences in India but does not work in our office. I don't think that the ISP here has nothing to do with this problem. Would be - this works the ADSL router in bridge mode? Can I make changes in the settings of the SPA to work around this problem?

    Any help is appreciated.

    The problem could be the firewall or the router, but it is also possible that your Indian ISP is blocking voip connections.  It was reported that is not unknown in India.  Sometimes this type of blocking is done by throwing packages for voip standard sip signalling port 5060. You can easily change the SIP port in the SPA3102 to traffic returning to the SPA packages and in fact routers often changes the port without your knowledge, but packets destined for voip provider must use the port specified by the provider number.  Since you can access the internet with your pc, I would try to run tests to see if this is the case.

    I ran a few ping tests and tests to see if I could save with other providers or services that use replacing or other sip signaling ports.

  • SPA-3102-backup/restore settings?

    Hello

    Is there a way to backup/restore the settings to a file in the SPA-3102 router?

    ASE

    There are several ways to save the settings of the SPA3102 according to some forums - check links ff

    http://forums.whirlpool.NET.au/Forum-replies-archive.cfm/756454.html

    http://Forum.Voxilla.com/Linksys-Sipura-VoIP-support-forum/SPA3102-compiler-configuration-backup-Mon...

  • Failure to register SPA-3102 on "DSL-2750E" D-Link router

    Hi team

    I guess I'm able to clarify this here since its associated VOIP Cisco device. This SPA-3102 works fine with my old router. I wanted to have a WiFi router better and I installed D-Link router to "DSL - 2750th". Internet, everything works normally through this router but SPA3102 is does NOT record. I have a debug trace attached SIP & don't know why it's a failure of registration. Not any other filtering or firewall configured in the router and it works in accordance with all the default settings. Would you be able to give advice on this please?

    Debugging is nice, but it discloses the contents of INTERNATIONAL packages only. No responses. Intercept (incoming and outgoing) SIP packets.

    I have the average time - do not use the names in the proxy configuration. Use the IP address.

  • Workforce Planning Admin Guide

    Anyone know good admin guide for workforce planning? Or at least a good blog post on the subject

    Thanks in advance

    Try:-http://download.oracle.com/docs/cd/E12825_01/epm.111/hp_11113_wfp_admin.pdf

    See you soon

    John
    http://John-Goodwin.blogspot.com/

  • SPA-3102 PSTN idle status, will not answer but watch sounds.

    Greetings,

    I am a complete newbie in the world of voip. I have an spa3102 and a computer virtual trixbox. When I use my softphone to compose, it makes to the spa3102 (shows the id of the last and gives a status of the appellant voip 'reply') but I get an "all circuits are busy now" and does not change the status of IDLE pstn. It also will not answer the phone for incoming calls to the PSTN.

    Outgoing stuff could be a problem of numbering plan (don't know not just guessing) here it is:

    (S0:xx. <@gw0>)

    I tried the regular (or default) (xx).

    incoming calls are supposed to go to a handset on my desk, for example ext 101 is the dial plan: (S0:101@internalip)

    I can't see the forest for the trees. Can someone give me some advice on where to look. I'm completely puzzled by something non-response externally, and why I get a all circuits are busy if there are inactive on the status page.

    an interesting note: If line1 is connected to an analog phone, it will dial a number, but always shows failover for a reason any...

    Thank you very much!!!

    Greetings!

    Thanks for the reply. I do not know if I explained properly (sounds like I don't have). I have a trixbox and I use the SPA in interface with my RTC and I want to have a fax machine (but later) on the FXS port. The problem I have is that I could not field calls to the collection. They would just ring and ring. I thought it was a dial plan (and hope it was not a hardware problem), but he just wouldn't answer the phone. He would show 'Ringing' like the PSTN status, but Voip would be "IDLE". I've been pouring through the guide of the administrator, forum messages for about 2 weeks now.

    But I didn't know what the problem was. The spa3102 is waiting until she can establish a connection (with the internal phone system) until it meets the PSTN. This is why it continues to ring. The problem why it shows it is inactive and (even with enabled full logging to a syslog box) no traffic to SIP the trixbox internal... because I had the port internal plugged in... not the WAN port (or internet). Thats right... silly me...

    I gave the wan port an address on the same subnet and moved the cable to it, once I could talk to her I change address internal to something even not on my network (if no routing problem) and left the network adapter disconnected (internal nic). Then I changed the wan to the old internal address address (trix trunk was already configured in this ip address anyway...) and PRESTO! I tried calling the number RTC and started to receive log entries showing the sip signaling and he's trying to route the call to the box of trix. It works now! So he was not answering the phone in my case, because it could not connect to the pbx or the ip phone and that because I don't use the WAN/INTERNET port on my SPA. Something I don't remember seeing in the textbooks as a "hafto' or a 'must '... I might have forgotten that of course, but I don't remember seeing him there.

    So if you enable logging, and then call this number (I used the PuTTY and 'tail-f /var/log/spa3102.log"to see the entries that they light up the box of syslog) and you don't see any sip traffic, it could be that you must use the WAN/INTERNET port instead of the internal port apparently logical... BE sure THAT ENABLE YOU REMOTE ADMIN if you decide to give it a shot.

    Also you can do the spa to answer the phone, even if it has no where to send the call (or if you want incoming people to use a PIN) on the GATEWAY PSTN - VOIP, there is a setting "off hook during the VOIP call" (default = no), but change that Yes - he would answer... and then sit there... If I had a PIN with a dial plan that is associated with this would give a fast busy after the entry of the PIN. BUT now everything is cool!

    Thank you!

  • help with SPA 3102 (question graphcal)

    HI guys here is my situation (I draw so it would be easier for future reference):

    I want to pick up A phone and dial the Ext 101 101, 102 for Ext 102 and so on.
    also, I want to put routed my call for location 2 location 1 for example transferring calls to 104.

    any help would be really appreciated even a starting point as for example the configuration of spa to route my call not NAT, so it can connect to the other.

    castro69 wrote:
    also, I want to put routed my call for location 2 location 1 for example transferring calls to 104.
    any help would be really appreciated even a starting point as for example the configuration of spa to route my call not NAT, so it can connect to the other.

    I guess that's an analog PBX, otherwise you wouldn't need the SPA3102 through the internet.

    For communications between the SPA3102, I would use direct ip call, using the external ip address and the sip port numbers.  Think that the SPA3102 is two separate cards inside the box where treat you everyone with its sip port number added to the external ip address common.

    I would setup port sip distinctive numbers on each of the baths to keep things straight.  You have a number of separate port for tabs of line 1 and line PSTN.  You will need to send these to the SPA3102 adapter port numbers in their respective routers or firewall of the router will reject incoming packets on the internetI would also convey the port range rtp for voice, flow packs.
    On each tab of the line 1 and RTC, you define NAT Mapping Enable: YES, not record, make call without Reg Yes, years call without Reg No. I put your external ip address on the Sip tab under EXT IP.  This will tell the SPA3102 to use this address in the sip signaling. I assume you are using static external ip addresses.   On each tab of the line 1 you would activate IP Dial Yes.

    The analog PBX is connected to the FXO port on one of the Spa.  You should check the voltage level hung up and won and then set the line parameter usage on the RTC of the SPA line tab to halfway between the two readings.  You can read the levels of tension on the PSTN line tab.  Calls to the PBX of the PSTN line tab will go through the voip to PSTN gateway.  I set up the catwalk with http authentication and configure a user name and password.

    Details are starting to become quite complicated.  I'd get running through steps.  Get a job step before moving on to the next step.

    The 1st step would be to get A phone call/receive calls to a PBX.  You can configure the line 1 for FXS phone attached A to use port location PSTN 2 as the proxy using http authentication, and you can then dial the extensions you want to call.  Location 1 SPA3102 will send a guest of the sip Protocol to the tab location 2 SPA3102 from pstn line and the SPA3102 will dial the number on the FXO port to the PBX.

    For calls coming from the other direction of a PBX to slot 2 SPA3102 the only place where you can connect a voip call is in the SPA3102 numbering plan.  If you want to call only phone that is easy, install you just dialers-messengers automatic telephone in the pstn-to-voip dial plan.

    I'm not clear about what you want to do with phone B I take is Extension 104.

    I like your designs.  Can save a lot of words.

  • Link to vWorkspace 8.6 Admin Guide

    I can't find the link for the vWorkspace 8.6 Administration Guide. I see the who's new and system requirements, but no administrator's Guide. Is there a Release Notes too?

    Thank you

    -Greg

    Hello

    You can use the below URL.

    support.Software.Dell.com/.../Release-Notes-guides

    See you soon,.

    Chandra

  • SPA 3102 - call "RTC for VOIP" setting is not on CLI/CID phone line active.

    Hi guys

    Recently, I discovered if the PSTN line is having with CLI/CID then helped the PSTN to VOIP Call not established with the standard settings. But others see (VOIP to PSTN) works well OK. Basically, it works well with the PSTN without CLI/CID lines. I guess when with CLI, there different voltage levels online. ?  You would let me know what are the parameters that I need to SPA in order to work with the PSTN line that allowed the CLI/CID please? This situation is covered by Sri Lanka Telecom PSTN lines. At the moment I have IT of standard parameters such as it comes with the SPA3102.

    Your feedback and help here...

    Syslog & debugging can save so much time...

    Line with no CLI:

     INVITE sip:[email protected]/* */ SIP/2.0 Via: SIP/2.0/UDP 192.168.1.2:5061;branch=z9hG4bK-a16a89a0 From: PradeephSL [email protected]/* */>;tag=4cc44dbb58f1a944o1 To: [email protected]/* */> Remote-Party-ID: PradeephSL [email protected]/* */>;screen=yes;party=calling Call-ID: [email protected]/* */ CSeq: 102 INVITE Max-Forwards: 70 Proxy-Authorization: Digest username="17772695735" realm="callcentric.com" nonce="684082550c6f8ce50da482371a591df7" uri="sip:[email protected]/* */" algorithm=MD5 response="01c15ae601d9d9f5af10023f908a1a4c" opaque="" Contact: PradeephSL [email protected]/* */:5061> Expires: 240 User-Agent: Linksys/SPA3102-5.2.13(GW002) Content-Length: 441 Allow: ACK BYE CANCEL INFO INVITE NOTIFY OPTIONS REFER Supported: x-sipura replaces Content-Type: application/sdp ... 

    This INVITATION is accepted by proxy.

    Line with CLI:

     INVITE sip:[email protected]/* */ SIP/2.0 Via: SIP/2.0/UDP 192.168.1.2:5061;branch=z9hG4bK-ea75ea0 From: PradeephSL [email protected]/* */>;tag=2d4fafa5d94faa2co1 To: [email protected]/* */> Remote-Party-ID: PradeephSL [email protected]/* */>;screen=yes;party=calling Call-ID: [email protected]/* */ CSeq: 102 INVITE Max-Forwards: 70 Proxy-Authorization: Digest username="17772695735" realm="callcentric.com" nonce="fd5a5e637b6e56fea56886ee25aababa" uri="sip:[email protected]/* */" algorithm=MD5 response="b6b1aa7104d1be764de5c74f369ef5be" opaque="" Contact: PradeephSL [email protected]/* */:5061> Expires: 240 User-Agent: Linksys/SPA3102-5.2.13(GW002) Content-Length: 441 Allow: ACK BYE CANCEL INFO INVITE NOTIFY OPTIONS REFER Supported: x-sipura replaces Content-Type: application/sdp ...

    This INVITATION is rejected by proxy with "403 incorrect authentication."

    But Howard has already struck and explained...

  • ID (CLI of the incoming caller SPA-3102) truncates the last digit when the telephone number is longer.

    Hi team

    Depending on the subject, when the number of the caller is Longer (i.e. International call with Country code etc.) as 11 digits, it truncates the last digit of the incoming phone number. See picture attached. Full number is 60126140235, but he loses the last digit is 5. Any suggestions?

    Also, there are comma (,) before the number that consumes valuable space. How elimiante that?

       

     FXO:Start CNDD fxo cnddwrap_feed parse ok 0060126140 status=2 -- Caller ID: -- Name = (null) -- Remote Number = 0060126140 -- Dialable Number = (null) -- No Number Reason = (null) -- No Name Reason = (null) -- Message Waiting = (null) -- Date and Time = 07/22 18:06 FXO:CNDD name=, number=0060126140 FXO:Stop CNDD FXO:CNDD Name= Phone=0060126140

    According to the newspaper that you have provided, the number of callers number claimed 0060126140.

    Length maximum support of the number in the E.164 format is 12 digits, including the country code. SPA don't know any used number format, so it has no reason to truncate 10-digit - I guess that he supported at LEAST 12 E.164 numbers.

    As the number seems to be broken on the side operators (00 superfluous as prefix, truncated to 10 digits) there's nothing you can to with him on the side SPA. We cannot guess figures sent by the operator to you...

    I can explain what is happening even on the side of the operators (although I'm only guessing) - I guess that we are talking of two digit country code country, so 10 digits is the maximum length of the national number. It seems your operator to consider the number national number and truncate them to 10 numbers on their side.

  • TANDBERG MCU TTC2-01 ADMIN GUIDE

    Anyone out there have a guide to the administrator for the MCU TTC2-01?  16 x 16 D3.9 fireware?

    Also need the CLI guide for this MCU...

    Cannot find a site via google or CISCO.

    Any help is appreciated.

    Thank you.

    I attached them to this answer, if you still get them let me know, so I'll send an email to you.

  • SPA-3102: how to fill the calls from SIP to PSTN and vice versa?

    Hello, since my ISP to my office blocked SIP ports, of I'll try and use it at home where the ATA works very well.

    If I call you ATA installed in my office in the United States (where there is no problem) to my ATA at home in India, I have how to route the call selectively to theFXS port or port FXO of the anti-terrorism Act in India? I I want to answer the call directly using the phone connected to the ATA instrument or make another local call out on the PSTN connection.

    TIA

    You get two accounts of Gizmo.  You put an account on the tab line 1, you put the other account on the PSTN line tab.  If you want to ring the phone attached to the SPA3102, you dial the account tab line 1.  If you want to get the tone to fill an outgoing line PSTN call, you call the account registered on the PSTN line tab.

  • TRUNK VOIP CREDITS SPA 3102


    reylon wrote:

  • Original SIPURA SPA 3000 help

    Five years ago, that I bought, directly from SIPURA, a new SPA-3000. I've never used but now I want to set up, but I want to make sure it has the latest firmware. I looked at the Linksys site (because any attempt to access www.sipura.com is redirected to Linksys) and found the firmware for the SPA-3000. Can someone tell me if this is the same unit as mine or changed from the original and the firmware does not work on mine?

    I tried to contact Linksys technical support, but their automated system tells me that I need to contact the dealer, who ironically is Linksys, since they bought Sipura. When I get to a real person that they just repeat that I have to contact the dealer of origin, they won't listen to me telling them that they are now the dealer.
    Can someone help and tell me what is the latest version of the software for this device and where I can download it? The configuration GUI displays the following information:
    Software version: 2.0.13 (GWg)
    Hardware Version: 2.0.1 (7067)

    Thank you

    Hello bsdaiwa, Yes this is the same unit. SPA-3000 has never really produced by Linksys, they later produced SPA-3102 units. Anyway, regardless of the producer of the unit (SPA or Linksys), they are able to use the same firmware.

    I myself have 2 pieces of SPA-1001 units, the 'old' box of Sipura, Linksys 'new' box, each of them having different revision HW and the two hapily run the same firmware 3.1.19 (SE) Linksys pages.

    Also, the SPA-xxxx units are protected from the flash of the incompatible firmware (for example from a different camera model), unit load the firmware first to the RAM, then check the "signature" FW, and that if it is the corresponding FW "signature" then unit flashes it it's rom flash and reboot.

  • SPA 3201 - problem with incoming calls

    Hello

    I installed a new SPA 3102 connected to a mini Server asterisk; catches of phone line to connect to the existing line of the Earth and the phone.
    The unit has current firmware, and the one and only ethernet cable taken in the WAN port - these two steps make a working direction. I can dial a number on the phone, the call goes through the asterisk and goes out to the PSTN.
    The other way, however, does not work: I get syslog entries that the call is detected, but the device doesn't send what anyone on the server (as checked with wireshark)
    The dial plan is
    (S0<:1234>)
    but I also tried
    (S0<>[email protected] / * />)
    and some variations more

    This is syslog entries:

    FXO:start CNDD
    Number of the caller analysis = callingnumber
    -Caller ID:
    -Name = (null)
    -Number distance = callingnumber
    -Dialable number = (null)
    -No reason number = (null)
    FXO:CNDD = name, number is callingnumber
    FXO:stop CNDD
    Phone = FXO:CNDD name = callingnumber
    Your RTC AUD:Stop
    FXO: on the hook
    Your RTC AUD:Stop
    the next sequence is repeated several times, probably as long as the line is actually ringing
    FXO:start CNDD
    Your RTC AUD:Stop
    FXO: on the hook
    Your RTC AUD:Stop
    FXO:stop CNDD

    Where would I look next?

    I found a tip in an ongoing discussion, and in fact this has solved the problem: "PSTN ring timeout" must be longer than the time to ring + break from the ring, and "Time of response to PSTN" must be short enough

    Unfortunately, if incomplete description of configuration. There are so many dial plans to set, but it has not specified that have configured it.

    Please read before RTC call the SPA3102 to VOIP. I hope this will help you.

Maybe you are looking for