SPA303 firmware upgrade error

Similar Questions

• The SPA3102 firmware upgrade error

  Hello

  Although I used my SPA3102 for a few years, she has recently become problematic. I sometimes hear audible clicking from the device that is associated with a red light flashes briefly on the power LED. If I'm on the phone at the time, the call is completed.

  I hope that a firmware update will address the issue, but I have been unable to upgrade 3.3.6 (GW). If I'm on a Mac, I don't understand the method of upgrading firmware using http or tftp. Fortunately, I ran Windows XP under Parallels Desktop for Mac and have been able to run the upg-spa3102-5-1-10-GW.exe program. However, a message is displayed: error in upgrading the firmware of the SPA > upgrade failed: no response from the SPA.

  Reading various forum posts on similar such problems, I was not able to find the solution.

  I have disabled the firewall on my Mac, the router (D-Link DSL 504 T) ADSL and Windows XP.

  I confirmed that the IP address of the SPA is 10.1.1.3

  I made sure that the firmware update is enabled in the Provisioning of the SPA configuration.

  I would be very happy to help you please.

  Thank you

  Bart

  These products are treated by the Cisco Small Business support community. (URL: https://www.myciscocommunity.com/community/smallbizsupport)

• The SG300 - 28 p - Firmware upgrade error

  Greeting is I downloaded Sx300_FW_Boot_1.4.0.88 update of firmware for switch SG300 - 28 p. The MD5 of the file signature match as listed on Cisco, but when I'm the download of the firmware (file .ros) to the switch I get the error message:

  Bytes transferred: 7011840

  Status: Failed to copy
  Error message: copy: the code SW file size is more

  Anyone else having the same problem? No work around?

  Thank you!

  Parth.

  Hello

  I like to think to upgrade the bootloader file(sx300_boot-13506.rfb) first, before trying the firmware. Boot loader are on the same zip folder as the firmware.you can use TFTP server to upgrade the bootstrapper.

  Interface WEB SG300 Cisco > Administration > file management > TFTP... When you select TFTP option for the fw 'BOOT' button is now available. Just type the name of the file and it should load the boot firmware.

  concerning

  Deborah

• Fake H710p PERC? -Firmware upgrade error

  Hallo,

  I recently bought a DELL PERC's H710p to the address but I can't update the firmware or install the driver. I always get an error like:
  "No controllers present or detected."

  First I thought that this is because the PERC H710p is not supported on a DELL R710 server. But after some research, I found something weird.

  The reason why the update of the firmware fails is simply the fact, that the "SUBDEV = 1f38" required when updating cannot be fond. My 'H710p' has a different SUBDEV. His SUBDEV is 1f77. So my question is, I bought some controller "false"?

  If this is not a 'fake' controller, what should I do to update my H710p and how to install the drivers?

  Thank you

  Here is the log from Megafl:

  Card #0

  ==============================================================================
  Versions
  ================
  Product name: adapter PERC H710P
  Serial number : xxxxx - Im not sure if its save to publish a sn on the internet. But if a job DELL need to check the controller, please send me a PM.
  FW Package Build: 21.0.2 - 0002

  Data from MFG.
  ================
  MFG Date: 01/04/13
  Transfer date: 01/04/13
  Revision no.: A00
  Battery FRU: n/a

  Version of the image in Flash:
  ================
  BIOS version: 5.30.00_4.12.05.00_0x05110000
  CTRL-R Version: 4.00 - 0014
  Pre-launch CLI version: 05.00 - 03: # 00008%
  FW version: 3.130.05 - 1587
  NVDATA Version: 2.1108.03 - 0093
  Boot block version: 2.03.00.00 - 0003
  STARTING version: 06.253.57.219

  Images pending in Flash
  ================
  None

  PCI Info
  ================
  Provider code: 1000
  Device ID: 005
  SubVendorId: 1028
  SubDeviceId: 1f77

  Host interface: PCIE

  Frontend Port number: 0
  The Device Interface: PCIE

  Backend Port number: 8
  Port: address
  0 4433221102000000
  1 4433221103000000
  2 0000000000000000
  3 0000000000000000
  4 0000000000000000
  5 0000000000000000
  6 0000000000000000
  7 0000000000000000

  HW configuration
  ================
  SAS address: 590b11c04b521300
  BBU: present
  Alarm: Absent
  NVRAM: present
  Debugger series: present
  Memory: present
  Flash: present
  Memory size: 1024MB
  TPM: Absent
  On board the Extender: Absent
  Key update: Absent
  Sensor of temperature for ROC: present
  For controller temperature sensor: present

  ROCK temperature: 57 degrees Celcius
  Temperature controller: 57 degrees Celcius

  Parameters
  ================
  Current time: 20:28:33 9/4, 2013
  Predictive failure polling interval: 300sec
  Interrupt the active gas number: 16
  Interrupt the completion of the throttle: 50us
  Regeneration rate: 30%
  PR rate: 30%
  BGI rate: 30%
  Consistency check rate: 30%
  Rebuild rate: 30%
  Cache flush interval: 4 s
  Max led to spin-up at the same time: 4
  Between groups of spin-up time: 12s
  Coercion of physical training mode: 128 MB
  Cluster mode: disabled
  Alarm: disabled
  Auto regeneration: enabled
  Battery warning: enabled
  ECC bucket size: 15
  ECC bucket leak rate: 1,440 Minutes
  Restore the hot spare to the Insertion: disabled
  Exposing pregnant devices: disabled
  Keep the history of the PD Fail: disabled
  Reorganization of host application: enabled
  Auto Detect Enabled BackPlane: SGPIO/i2c MS
  Load balancing mode: automatic
  Use only the FDE: Yes
  Security assigned key: No.
  Security key failed: No.
  Not saved security key: No.
  Default policy LD PowerSave: controller set
  Maximum number of disks to connect direct to the top at 01:00
  Any Cache offline VD kept: No.
  Allow booting with preserved Cache: No.
  Disable controller Reset online: No.
  KFC in NVRAM: No.
  Use the disk activity to locate: No.

  Capacity of
  ================
  RAID levels supported: RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, 11 with covering PRL, layout of PRL11-RLQ0 DDF with no span, DDF PRL11-RLQ0 available with span
  Supported disc: SAS, SATA

  Permit mixture:

  Mix allowed attachment

  Status
  ================
  ECC Bucket Count: 0

  Limits
  ================
  Max of weapons by VD: 32
  Max extends by VD: 8
  Max tables: 128
  Maximum VDs: 64
  Max parallel orders: 1008
  County EMS max: 60
  Max Data transfer size: 8192 sectors
  Max band PerIO: 42
  Band of min size: 64 KB
  Max band dimensions: 1. 0 MB
  CacheCade varied size: 512 GB
  Current size of CacheCade: 0 GB
  The current size of the Cache FW: 887 MB

  Current device
  ================
  Virtual drives: 1
  Gradient: 0
  Offline: 0
  Physical devices: 2
  Disks: 2
  Critical records: 0
  Has no records: 0

  Card operations support
  ================
  Rebuild rates: Yes
  Rate of CC: Yes
  BGI rate: Yes
  Rebuild rates: Yes
  Patrol read rate: Yes
  Alarm control: Yes
  Cluster support: No.
  BBU                             : No
  Spanning: Yes
  Dedicated backup: Yes
  Reversible spare discs: Yes
  Foreign Config import: Yes
  Auto diagnosis: Yes
  Allow the joint redundancy on table: No.
  World Relief: Yes
  Deny SCSI Passthrough: No.
  Reject the SMP Passthrough: No.
  Deny STP Passthrough: No.
  Security: Yes
  Snapshot enabled: No.
  Support ECO without adding drives: Yes
  Support the KFC: No.

  Operations supported VD
  ================
  Read the policy: Yes
  Write policy: Yes
  IO policy: Yes
  Access policy: Yes
  The strategy of Disk Cache: Yes
  Reconstruction: Yes
  Deny locate: No.
  Reject the CC: No.
  Allow encryption Ctrl: No.
  Turn on LDBBM: Yes
  Breakmirror support: Yes
  Energy savings: Yes

  PD supported operations
  ================
  Force online: Yes
  Force offline: Yes
  Rebuild the force: Yes
  Deny the Force failed: No.
  Deny the good/bad Force: No.
  Refuse to replace missing: No.
  Deny Clear: Yes
  Deny locate: No.
  Support temperature: Yes
  Disable the Copyback functionality: No.
  Enable JBOD: No.
  Enable the feature Copyback on CHIP: No.
  Activate Copyback of SSD on SMART error: No.
  Select SSD read: No.
  PR Correct unconfigured areas: Yes
  Enable Spin Down of unconfigured disks: No.
  Turn off the Spin Down of the hot spare function: Yes
  Spin-Down time: 30
  T10 power state: Yes
  Errors counters
  ================
  Memory correctable: 0
  Mistakes not rectifiable memory: 0

  Cluster information
  ================
  Authorized cluster: no
  Cluster Active: No.

  Default settings
  ================
  PHY polarity: 0
  PHY PolaritySplit: 0
  Base rate: 30
  Band size: 64 KB
  Hunting time: 4 seconds
  Write policy: WB
  Read the policy: Adaptive
  Be cached when BBU Bad: disabled
  IO caching: No.
  SMART mode: Mode 6
  Turn off the alarm: No.
  Mode of coercion: 128 MB
  ZCR Config: unknown
  Dirty disk activity LED Watch: No.
  BIOS continue on error: No.
  Spin-Down Mode: no
  Authorized device type: SAS/SATA Mix
  Allow Mix attachment: Yes
  Allow to Mix SAS/SATA HDD to VD: No.
  Allow Mix SAS/SATA SSD in VD: No.
  Allow Mix HDD/SSD in VD: No.
  Enable SATA in Cluster: No.
  Chained Max speakers: 4
  Disable Ctrl-R: No.
  Enable Web BIOS: No.
  Direct Mapping PD: Yes
  BIOS enumerate VDs: Yes
  Restore the hot spare integration: No.
  Exposing pregnant devices: No.
  Keep the history of the PD Fail: No.
  Disable any perforation: No.
  Zero based speaker enumeration: Yes
  PreBoot CLI enabled: no
  Disk activity see the LED: Yes
  Disable cluster: Yes
  Disable SAS: No.
  Auto Detect Enable BackPlane: SGPIO/i2c MS
  Use only the FDE: Yes
  Led enable header: No.
  Delay during the POST: 0
  EnableCrashDump: No.
  Disable controller Reset online: No.
  EnableLDBBM: Yes
  Uncertified hard disk drives: enable
  Treat simple span R1E as R10: Yes
  LD max by the Bay: 16
  Energy saving option: don't turn down the readers not configured
  Don't turn down hot spares
  Do not Auto centrifuge configured Drives
  Power settings apply to all readers - cannot set the individual parameters of power PD/LD
  Max power savings option is not allowed for LDs. supply Conditions only T10 should be used.
  Written in cache is not used for queue down VDs
  Annex can disable save energy at the level of the controller
  By default the spin time in minutes: 30
  Enable JBOD: No.
  Journal of the ATS in Flash: no
  Auto improved Import: No.
  BreakMirror RAID support: Yes
  Disable the join mirror: Yes
  Time required to detect the CME: 60 s

  Exit code: 0x00

  Controllers H710 series have been tested and validated in the Dell only 12 servers (such as the PE 720) generation.   Further, check your H710p came from a Precision Workstation.  The following valid this information, which came from the file nocheck.bat for this controller:

  OFF @Echo
  CLS

  put the FW = 21.0.2 - 0002
  Set ROM = H710PAWS.rom
  SUBDEV = 1f77 set
  DOS32A = set / AC /NOWARN:9004

   
  You will need this patch: http://www.dell.com/support/drivers/us/en/19/driverdetails?driverid=CGM2K which is the latest available for this particular controller.

  The controller may or may not work in your PE710, it just has not been tested or validated.  Good luck!

  Kind regards

• BDX4350KB Wifi adapter and firmware upgrade doesn't work do not

  It is a sequel to my earlier question about if the WLM-20U2 Wifi adapter will work in my blu - ray player.

  After buying the adapter I plugged it and a message 'not supported', if I tried to connect wireless it says there was no an adapter connected.

  So I assumed that this necessary upgrade, so I formatted a 1 Gb USB drive with the FAT file system, downloaded the file level (version 39 http://www.dl.toshiba.com/player/NA/GB/EN/BDX4350KB.html) and copied the file .bin on the USB.

  When I plugged into the player and said to check the disk for a file to update it tells me that "frontend file is not found"... There was only one file to download, and it wasn't in a folder so I guess I'm supposed to just copy that file on the USB drive.

  I checked the USB port with a memory stick with photos on and it works fine.

  How to get the upgrade to work in the hope that it will enable the wifi adapter to work?

  Thank you

  Have you checked the guide in PDF firmware update?
  [Update firmware BDX4350KB | http://fget.dl.toshiba.com/manual/install/10009/Installation_Instruction.pdf?fromPid=%2Fplayer%2FN A%2FGB%2FEN%2FBDX4350KB.html&f=Installation_Instru ction.pdf]

  _ * How to upgrade the F/W * _

  (1) update firmware requires the USB of size max.2GB. Please make sure you format the Flash DRIVE to FAT/FAT32 before you start the upgrade procedure.
  ? Create a new folder on the USB drive and name it UPG_ALL
  ? Unzip the firmware file and copy it in the folder UPG_ALL.

  2) turn on the BD? Drive and make sure that you can see the player's on-screen Menu.
  ? Insert the USB key containing the Firmware upgrade file in the USB of the Blu slot? ray player

  3) press the "SETUP" button on the remote control.

  ? Select keys on the remote control UP/DOWN
  ? Symptom
  ? Upgrade
  ? USB storage device

  4) press the OK button on the remote control depending on the USB storage device.
  ? Now the upgrade file is under research. Please wait massage will appear

• 200 d IOmega IX4 Firmware upgrade failure

  Hello

  I have an IX4 - 200 d which I inherited. Initially, it wouldn't boot and display only the symbols of USB stick/network after about 60 seconds.

  With some searching on Google, I created a boot disk USB with the firmware updated on this issue. All goes well until the Firmware upgrade begins. I go to the step of (what I assume is) the upgrade of the firmware and it gets 75%, hold for 5 seconds and then the machine stops.

  I tried to repeat the update of the firmware with all the drives present, with every other drive in the first slot and with all the disconnected drives. But it seems to behave in the same way.

  Is this a known issue? Or could it be a hardware failure?

  I'm pretty eager to find a solution - it takes a long time for me to accept defeat.

  The only other suggestion that suggested Dr. Google is to start linux and reformat the hard drive?

  Any help is appreciated.

  Kind regards

  Pete

  Hi André,.

  This case can be closed.

  After the above mentioned procedure eventually work, I didn't know that - ALL readers should be present and formatted during an attempt of USB firmware update / install.

  The link again on the forum - http://forum.nas-central.org/viewtopic.php?f=14&t=4401

  This seems to be the only solution.

  Kind regards

  Pete

• LaserJet 3020 upgrade error

  My Laserjet 3020 does not at all. A message is displayed on Didital sign indicating "UPGRADE ERROR, CALL HP HELP DESK".

  Please advice how ractify it.

  Alharamain wrote:

  I don't have. Since I do not know any number of support HP in Karachi centre.

  Try this:
  http://www.romakhi.com/

  Computers of Roma was created in 1988 and 20 years computer Roma has itself in magnates Macho in World.Roma a computer is authorized dealer of Hewlett Packard (H.P.).

  http://www.romakhi.com/contactus.html
  

• Jump and mix tracks after firmware upgrade?

  I can't explain it. Since the latest firmware upgrade Fuze my wife started jumping titles (for example jump to the next song to halfway through the current), but a funniest part - he mixes parts of files. We can listen to a song, and then all of a sudden he would be interrupted by 1 second of a file from a different album and then come back to play the first song from the point it was interrupted. What gives?

  Me that was too much.  I downloaded all my music back and reset my Fuze and reformatted it.

  Charge of excessive songs and back on went.

• BEFW11S4 v.4 and Vista - firmware upgrade failure

  Hello

  I've had this router for about 5 years, it runs with XP without any problem. Since I got a new laptop with Vista, the wireless connects for an hour or two, and then falls back and I have to unplug the router for five seconds, then reconnect to reconnect (my other laptop with XP has not this problem).

  I understand that there is compatibility between the BEFW11S4 v. 4 and Vista problems so I tried to update the firmware of dartybox.com and kept getting a message that failed. I hard rebooted the router but button of restart 30 seconds and the upgrade has always failed. I so re-set to factory settings through the online admin to the router, re-uploaded the implementation level and still got the emssage failed (I am sure that the model number & version is correct and I download the appropriate firmware upgrade).

  Is there anything else I can do another one) buy a new router; (b) living with school drop-outs; (c) remove Vista and go back to XP?

  Thank you

  Bigdank

  Genius! I have changed the name of code.bin, went to the admin > tab upgrade firmware and the upgrade file. I had a wireless without interruption ever since, even after the awakening of the laptop to sleep.

  Thanks for your help

• BEFSR81 Firmware Upgrade Gone Bad?

  Just putchased a new BEFSR81 router.  Using the installation CD, I got it Setup and works very well.  Then, I went to the support of Linksys and found page a more recent version of the firmware.  My version is 2.51.4.  I downloaded the 2.51.4.6 version and installed. I made sure to choose the version for my model 3.1. He appeared to install OK, because I got the message that it was for the page in 5 seconds.  Now I can't go to the web-based configuration page.  I can ping 192.168.1.1 and get a normal response, but by entering that address in my browser just times out.  I turned off the router and even held the reset for 30 seconds, but don't can't go in the web-based configuration page.

  This router is now watered?  Do I need to send it back?

  Thanks for any help on this.

  Found the answer in this thread:

  http://homecommunity.Cisco.com/T5/wired-routers/failed-firmware-upgrade-bricked-BEFSR41-v4-3/TD-p/25...

  Thanks Wizzard!

• The Linksys BEFSR41 V2 Firmware upgrade help

  I can't open the MacBinary (.bin) files that I downloaded from linksys, in order to update my firmware. I used my utility to archive, Stuffit Expander Mac and BetterZip, and so far none of them opens the file. Anyone have the firmware upgrade in a different format or advice on how to solve my problem.

  Do not touch the file you downloaded. The only software that uses it is your browser.

  You must open the web interface of the router at http://192.168.1.1/ and then use the upgrade of the firmware here.

  I don't know if the demo user interface is always up to date, but if it is as you should find it on the help page. See here. Click Update Firmware. Then, press the Browse button and select the .bin file that you downloaded. Then press upgrade and the browser will download the file on the router.

• WRT 160NL firmware upgrade ever end!

  Hello

  I am trying to upgrade the firmware version 1.00.01 B15 to 1.00.01 17 (the only one available on the linksys Web site). It is not allowed to turn it off or reset it. However, the upgrade progress stopped at 98% and never ending so far. Should I wait longer (another day)? Or I can just reset/power off of the it?

  Attached is a snapshot of the screen for reference.

  Thank you.

  

  The firmware upgrade process must be complete...

  Try the following steps... Press and hold the button of reset for 60 seconds... Release the reset button and unplug
  the power cable from your router, after only 30 seconds reconnect the power cable...

  Now, as do the settings of the browser on the computer... Open an IE, click Tools > Internet Options, and then delete all files, cookies, history, forms... GoTo 'Connections', make sure never Dial
  a connection is checked, click on network settings and make sure that all the options are unchecked... Once you are finished, click OK... Close IE and reopen...

  Now, try to upgrade your router firmware... it should work!

• WRT610N firmware upgrade question

  I have a simple question about the firmware upgrade.  I want to know if it's OK when the upgrade of the firmware on a wireless router for rather than press reset and rest for 30 seconds, that I connect with my browser and 'load Factory Deaults?

  I read, where they are supposed to do the thing of the SME and the method of web browser is much easier worth me.

  Can anyone confirm this or should I press the button to reset for 30 seconds?

  see you soon

  It is advisable to reset the router after the upgrade of the firmware. For once you upgrade the firmware on the router... Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now, you can re - configure your router.

• Windows Vista Service Pack 4 upgrade errors - Error Codes 643 and D59

  original title: errors for Service Pack 4 Windows Vista update - error code 643 and D59 - I do not KNOW WHAT to DO!

  Windows Vista Service Pack 4 upgrade errors - Error Codes 643 and D59

  I DON'T KNOW WHAT TO DO!  I tried what he suggested, but cannot cross the error codes!  I am upset and frustrated because I can't work with the internet without slowing down.  I then close, only to have start all over again EVERY time!

  My internet keeps acting like dial upward because of this and I have cable internet!

  Help, please!

  This day SP4?

  Only in appropriate cases:

  When installing updates using Windows update or Microsoft Update you may receive error 80070643 0 x or 0 x 643
  http://support.Microsoft.com/kb/976982

  Just in case where it is .NET Framework 4 -

  You can try the case just only repair the .NET Framework versions affected, especially if only .NET Framework 4 is involved.

  To repair the .NET Framework 4 Client Profile or .NET Framework 4 extended etc. -.

  • Click on start/Orb and click on Control Panel.
  • Go to the program and features.
  • Locate the Microsoft.Net Framework 4 Client Profile or .NET Framework 4 extended, right-click.
  • You should have the choice to repair or uninstall/change, click it.
  • This will then give you the opportunity to fix it
  • Select the repair option.

• Please help KB 976370-Upgrade error code-80073701

  Please help KB 976370-Upgrade error code-80073701

  Windows Update Forum:

  It comes with Vista, upgrade install and activate Forum.

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner