Specify the device during the scan over network (HP1212nf MFP)

Similar Questions

• M1536 Save Scan over network

  I want to scan documents to a place predefined on the network without providing the location whenever I scan. This is possible on the M1536 printer?

  Hi EdgeCS,

  Welcome to the HP Forums, I hope you enjoy your experience!

  I understand that you want to save the scan to a specific folder.

  I'll be happy to help you.

  I have provided a document for How to digitize.  This will allow you to create a location for your scans.

  Select the following text in the document to select a backup location:

  • How to scan with the HP software.
  • How to scan a document or a general picture.
  • To change the advanced settings of scanning.
  • You can specify the location to send saved scans the computer.

  I think that this will provide a solution to your problem. Thank you.

• LaserJet professional M1217 nf: cannot scan over network with a printer laserjet 1217 on a Mac

  Hello

  My set up:

  Mac with Yosemite

  LaserJet M1217 more wireless

  Description of the problem:

  I can't scan. Preview, the control panel or image capture, I get the same error saying "cannot open a session.

  I have installed and reinstalled the drivers/printer about 100 times.

  I tried to add the printer/scanner like airprint, or with the name of the printer as a proposed post.

  Just what causes the same error.

  I have the 2.0 version of the driver installed right now. Tried with 1.7, same result.

  I can print without problem since my Mac and my iPad.

  Tried it with an ethernet cable and have the same problem in case someone ask.

  I looked all over google and doesn't seem like someone else has the same problem? Many people have problems printing over wireless, but it's ok for me. Is the scan, I can't go to work.

  Pages of HP does not offer any other driver which has of the Yosemite. HP offers no additional program for Mac and scan.

  Don't know what else to try.

  Little help? Anyone?

  Thanks Geminy02,

  Unfortunately, your suggestions did not help, and I have a few comments about them.
  First of all, your suggestion about the router was the problem is quite impossible, as you will need to check if the ports are open only in the case we're talking about two different network segments. If you have your printer and your computer in the same segment you will have problems of ports.
  Second: if I would have chosen IP protocol to add my printer, I wouldn't take the option scan, as you said, which means I could not done any tests that I mentioned in my original post, and I would never have had to the point of getting the error message.
  Thirdly: the drivers that you MENTION for download are exactly the same as you get with yosemite, so, this could help to reinstall the driver, it's kind of a long shot (and yes I tried).

  In fact, I managed to solve my problem by doing a factory reset of the printer, any sign of a printer in my computer, cleaning and reinstall the printer using the airprint driver suggested by yosemite where to find my bounjur printer.

  I tried ro think what could be the reason, or to see all what I had changed, and the only thing I've seen different in the configuration before and after he started to work was the name of the printer. When it did not work my printer was called simply "printer", when he was working he was the full name that comes by default. It would be very strange, that this is the reason, but I just mention it here just in case someone read. I believe that the factory reset was the difficulty, not the configuration itself.

  Just for the other readers, I can confirm that this unit can print and scan over my wiresless and cable network on yosemite, with the help of preview, capture image or scan property in the control panel. It took me several hours to make it work, but it does, and my best friend was all the time the printers web page, where you can change the configuration of the printer.

• Able to print not scan over network, with Officejet 6500 E710n-z

  I tried with and without wire.  Printer was not detectable when connected wireless.  WLAN in wireframe, but can not scan from my office.  It gives an error of communication.  To print.  Tried with firewall disabled.  No chance!  Help, please.

  I solved it by turning off all computers, printer, router and modem and turn them then turn it back on.  It worked and now it works fine.  Thanks for your help...

• OfficeJet 8620: Error using scan to network folder - although the EWS test demonstrates the success

  I have configured the 8620 via the integrated Web server for scanning to \ \Scans < ip address of my macbook > the 'test' function's successful return.  However, when I run a scan to network folder in the control panel of the printer, I get the error: "cannot write in------< ip address > \Scans.» Destination folder is read-only, has the wrong permissions, or is no longer available. "I don't see how that's possible given the test of EWS.  I confirmed that the file is read-write for all.

  Hi @tfeeneytx

  I see that you have taken the lead and sent the scan to network folder problem you encounter as you mentioned that you on your previous post. I'd be happy to help you with this also.

  Please use the following document to ensure you have the analysis of the configuration of the network folder correctly; Scan from the control panel (including the Scan to Email, in PDF format, and to a network folder) for Printer series e-all-in-one HP Officejet Pro 8610, 8620, 8630, 8640, and 8660.

  Please also ensure you have the latest update of the firmware for the printer; Update of the Firmware 8620/8625 e-all-in-one printer Officejet Pro HP.

• Try to configure the scan to the network folder, name of user and password is incorrect about JO 8600 N911n

  Hello - I have an Officejet 8600 N911n, product number CN577A. My OS is 64-bit, Win8

  My error message is either your user name or password is incorrect, please go back and correct your user name or password.

  No changes were made because this system has a few months other than downloads.

  I tried using the username provided by the scan to network folder setup with the IPL used for the HP forum and support. Also, I deleted the user name provided by the scan to network configuration folder and created a new pw. They have also objected. What user name and pw should be used?

  Hi Wardell1,

  I appreciate that you try to configure the scan to network folder.

  Where do you get this error message?

  Do you get this error message when you try to access SAP of the printer?

  You get this message on the printer?

• M277dw MFP: MFP M277-DW Scan to network folder

  In the settings of the printer - tab analysis - scan to network folder Option. I tried to capture the information of folder in smb and afp format. None is accepted by the printer. Can anyone help? Note that this is to connect the printer to a shared folder on a MAC

  Thank you

  Hey @Hopflys, welcome to the Forums of HP!

  If I understand correctly, you configure the scan to network folder and despite your efforts, shared folder information is brings not accepted. Please take a look at the following post, written by @Gemini02 , as well as the steps to configure the feature described and easy to follow: Re: configuration of scan of file.

  If you need assistance, I would like to know the results of your efforts and I will do my best to help. If this solves the problem you are experiencing, please be sure to click on the I accept as Solution button below so that others can see what has worked for you.

  Thank you.

• Specify the network during the creation of the VM...

  Hello

  My apologies in advance if this is a question well beaten, but I did some research on Google and not find the answer to this day...

  I'm creating a number of virtual machines based on the opinions of a CSV file and want to specify the network that must be the new virtual machine. This command works...

  $vm = New-VM-Name $_. Name - model $_. Model-host $_. Home - Datastore $_. Data store - OSCustomizationSpec $_. CustomSpec-confirm: $true - RunAsync

  But when I try to specify a network to attach to, with the addition of -NetworkName $_.Network I see the error...

  New-VM: all parameters can be resolved by using the specified named parameters.

  C:\PowerCLI\deploy.ps1:18 char: 9

  + $vm = New-VM-Name $_. Name - NetworkName $.network-model _ $_. Temp...

  + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  + CategoryInfo: InvalidArgument: (:)) [new-VM], ParameterBindingException)

  + FullyQualifiedErrorId: AmbiguousParameterSet, VMware.VimAutomation.ViCore.Cmdlets.Commands.NewVM

  
  

  If I create the virtual machine and then run the following command, the network is OK for the virtual machine.

  Get-NetworkAdapter $_. Name | Together-NetworkAdapter NetworkName-$_.Network - StartConnected: $true

  I believe that it is not possible to specify - NetworkName when you also specify a customization specification.

  
  

  How could I go on create virtual machine and the specification of its network in this scenario (and within the same VM creation script)? Is it possible to use PowerCLI to make the same changes as those available in hardware virtual machine (experimental) 'customize' user interface that allows the user to select a network during a deployment based on a model?

  Thanks in advance and I hope you can help.

  Matt
  

  The parameters of Model & OSCustomizationSpec and Networkname belong to different parametersets on the New-VM cmdlet.

  You don't have them together on an invocation of New - VM.

  As you have already discovered, you can make game-NetworkAdapter after the virtual machine has been created.

  New-VM-name $_. Name - model $_. Model-host $_. Home - Datastore $_. Data store.

  -OSCustomizationSpec $_. CustomSpec-confirm: $true |

  Get-NetworkAdapter | Together-NetworkAdapter NetworkName-$_.Network - StartConnected: $true

  But the drawback here is that you cannot use the RunAsync switch on the New - VM cmdlet.

  An alternative is to create virtual machines with switch RunAsync, wait until the virtual machines are created and the customization complete, before changing the portgroup.

  There is a good method described on the PowerCLI blog waiting for the customization of the OS to complete

  And Yes, you can create an OSCustomizationSpecs with PowerCLI, take a look at the New-OSCustomizationSpec cmdlet.

• Specifying the NIC Public private network cards during the Installation of the grid

  Version: 11.2
  Operating system: Solaris
  
  We will install the 11.2 grid.
  These are IP addresses, we will allocate for the Public sector and private Interfaces
  

  bge0--->10.80.143.214 ---- for public network (Subnet mask 255.255.255.0 )
  
  bge1--->172.132.116.81 ----- for private Interconnect (Subnet mask 255.255.255.0 )

  But, during the Installation of the grid, the grid Setup will ask only those IPs with the last byte 0 as shown below url

  bge0--->10.80.143.0 ---- for public network 
  
  bge1--->172.132.116.0 ----- for private Interconnect 

  http://4.BP.blogspot.com/_0ut-UEg1S3k/SqI3w1QgVLI/AAAAAAAAA1w/Zq6jwWWh_48/S1600-h/8.PNG
  
  The installer actually displays the "subnet". But Public and private NIC of the subnet is 255.255.255.0
  Is this really? Why the installer of the grid is not inviting the real IPs allocated to networks of Public and private?

  Hello
  Litte Note:

  Why the installer of the grid is not inviting the real IPs allocated to networks of Public and private?

  The cluster runs under Network (e.g. 10.80.143.0) under any one or two IP, because several IP addresses of the network in question can be used (it is about scalability and availability), you install a cluster it show the networks used, not used IP (this occurs in any system of cluster, you must specify the network).
  Kind regards
  Levi Pereira

• LasetJet Pro M475dn: Impossible to scan over the network after upgrade to El Capitan

  After that I upgraded to El Capitan I no longer use HP Scan or HP Easy Scan to scan the network more. I can print to the printer, but analysis always results in the page being pulled by the document feeder, but applications just to lock-up without the document showing. Everything worked fine on Yosemite.

  I found a workaround solution that once worked before after a update of Mac OS X (but had to change the name of file, much like the original file has disappeared). Just download the next file on HP (no matter that it is not for your printer; it's not mine either (OfficeJet Pro L7680) but it works).
  
  FTP://FTP.HP.com/pub//softlib/software12/COL51752/OJ-125213-3/HP-inkjet-SW-OSX-Mavericks_v12.34.37.dmg
  
  Disable SIP for this installation and when you run the installation program (do not know if you need to do, but I did anyway). To do this, the instructions are here:
  
  https://forums.developer.Apple.com/thread/3981
  
  When you run the Setup program, make sure you hold the CTRL key when you right-click on it, then click Open in the menu.
  
  Run the Setup program. Be sure to select the HP scanning software and install it. When you get to the configuration of the printer, just skip this step (unless you are using the printer in question). The parser components are what you really want from the printer drivers are already in El Capitan, if you have a HP supported printer. The scanning software will have already installed to the moment you arrive at this screen.
  
  Install the HP Easy Scan on the App Store app (if you get the latest version of the software your front-end). You should be able to run the scanner and scans without restart. I don't know if it will work for everyone, but certainly, it worked for me and keep me until they find what went wrong in El Capitan to disable scanning and scanning capabilities.
  
  SIP turn on again so that your Mac is better protected. We should all work after that. After doing the above, I found that I was able to not only use the HP software, I was able to use Image Capture, preview, etc, to get images from the scanner. Your mileage may vary, but if all goes well it will work again for you all.

• LaserJet MFP M177fw Pro: M177fw can scan over the network

  Hello

  I would like to know if the printer permissions 'M177fw' to use the scanner to a pc connected via LAN. (based on analysis of the computer or send the scan from the printer to a network folder)

  I found this information on the manual.

  Thank you

  Hey @mariwf,

  Yes, if you have the printer connected to your wireless network, you can scan all the same that you would be using a USB connection. You don't have to use the built-in Web server, you can open and use the HP scanning software.

• Cannot run any application system as anything in the administration tools, network and sharing Center, Device Manager. No problem running the applications Office, IE, etc.

  Vista Ultimate, 32-bit, SP2 had worked perfectly for two months. Machine set up to now and when started the first time, no network connection and my video wallpaper stops with an error message that says to reboot. The 2nd restart, I get internet connectivity, no wallpaper at all and no access to system applications that are listed in the title line.

  I can open Documents and navigate around, click computer and see the disks, etc., right click on computer and view the properties, but it shows no RAM and processor. If I click on Device Manager on this window, it crashes just forever unless I have kill with Task Manager.

  I had Windows Live Onecare on this machine and it expired during the period, it was closed. No problem... I plan to install MSE.

  Originally, I installed a smaller version of Vista of CD (still have it) but upgraded to Ultimate online and is not a product for this upgrade CD.

  I need to know where to start on fixing Vista so that it works correctly.

  Thank you.

  Hello

  ·        Where you upgrade the system for full vista?

  It is better that you have the Vista Ultimate DVD, so I suggest you ask the DVD from the dealer.

  I suggest you to check in the Event Viewer logs and let us know the exact error.

  Open event viewer

  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer

  Method 1:

  I suggest you to do a scan of the SFC. File system (CFS) Auditor verifies that all Windows 7 system files are where they should be as they are by default and not corrupted, changed or damaged.

  a. Click Start, click principally made programs, accessories, right-click on command prompt and select run as administrator.

  b. click on continue or provide administrator credentials if prompted.

  c. in the type in the following command prompt window and press ENTER:

  d. sfc/scannow

  e. you should see the following message on the screen:

  § Begin the analysis of the system. This process will take time.

  § Beginning verification phase of system scan.

  f. % verification complete.

  g. once the scan is complete, a test to see if the problem you are experiencing is resolved or not.

  For more information, see the article mentioned below.

  http://support.Microsoft.com/kb/929833

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Publisher cannot connect printer wireless Officejet 6500 has E710e and the laptop over the network

  I just changed my ISP and moved to British Telecom, who sent me a new router. The new service is in place and working well and I reconnected my Officejet 6500 a E710e CN557A to the wireless network. But I can't connect the printer to my laptop no matter what I try. I have uninstalled and reinstalled the printer on the laptop using the original CD and then updated to the latest drivers. I even reset the printer to default and then network related setting before attempting to connect the portable computer whose IP address of the printer without success. My laptop OS is Windows 7 32 bit and the printer is just over a year. He worked like a dream with the old wireless network.

  I have already downloaded on my laptop HP - HP Print and Scan Doctor diagnostic tools and troubleshooting network printer connection. Printing and scanning doctor can't see the printer and I followed the instructions of troubleshooting without success.

  Any help and advice would be much appreciated.

  If it is a BT Home Hub, they don't play well with HP wireless printers.

  You can try this - remove all instances of your printer in Control Panel > devices & Printers. Then:

  1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing. Get his IP address for a network Test printed on the front of the printer.
  2. click on > start > Control Panel > devices & Printers.
  3. click on add a printer
  4. Select local printer
  5. Select create a new port and select Standard TCP/IP Port, and click Next.
  6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
  7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
  If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
  8. If prompted, use the driver that is currently installed.
  9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
  10. we may ask you to share the printer. Choose No.
  11. the printing area of Test Page is displayed. Go ahead and print it out.
  12. click on finish.

• Computer laptop Windows 7 can see other wired PC via a wireless connection by specifying the box "search programs and files" drive letter in the start menu, but not in the network screen

  My laptop with Windows 7 (64-bit) can not see the other desktop PC running Windows XP via a wireless connection, except if it is plugged into my laptop so only I can see them on the network.
  I checked all the working groups to ensure that all are the same.

  However, when my laptop into Wi - Fi, I could see the other wired desktop PC by specifying the network path in "search programs and files" to the start menu in the Windows 7 laptop, I was able to add network folder by specifying the drive letter for the connection and file I want to connect via a right click on the network to connect a network drive...

  Then, finally I can access any other desktop pc wired to shared folder via the Wi - Fi by this method.

  But I still don't see them on eventhrough network I can access by this method. Please help me solve this problem.

  Hi Hkway,

  • You are able to see the Windows 7 machine Windows XP computer when connected through wireless and if it is accessible through network?

  First of all, check if the NetBIOS protocol is installed on your Windows XP computer. To install the NetBIOS Protocol, follow these steps:

  1. click on start, click on Control Panel and then double-click network connections.

  2. right click on the card that you want to add NetBEUI to and then click Properties.

  3. on the general tab, click on install.

  4. click on Protocol and then click Add.

  5. Click to select NetBIOS protocol in the list, and then click OK.

  6. restart your computer.

  Also make sure that NetBIOS over TCP/IP is enabled in the Windows XP computer. To do this, follow these steps.

  Turn on NetBIOS over TCP/IP

  1. click onStart, click on Control Paneland then click on network connections and Internet.

  2. click onnetwork connections.

  3. right click onLocal area connectionand then click Properties.

  4. click onInternet Protocol (TCP/IP)and then click Properties.

  5. click on the tabgeneral and then click Advanced.

  6. click on theWINS tab.

  7. underNetBIOS setting, click Enable NetBIOS over TCP/IP, and then clickOK twice.

  8. click onclose to close the local area network connection properties dialog box.

  9. close the network connections window.

   

  After following the above steps, check if you can access the computer Windows XP of Windows 7 computer using the wireless connection.

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• By specifying the host name for the database during installation

  I installed the database 11g r2 as a Server Desktop, anywhere during the installation it asked me to review or change the host name. It is automatically used as the host name "localhost" and wrote in listener.ora, so no other machine on the network is able to use it. Only, it connects since within the same machine. Please help how to specify the host name during installation.
  
  Published by: user4928701 on July 8, 2011 23:15

  user4928701 wrote:
  I installed the database 11g r2 as a Server Desktop, anywhere during the installation it asked me to review or change the host name. It is automatically used as the host name "localhost" and wrote in listener.ora, so no other machine on the network is able to use it. Only, it connects since within the same machine. Please help how to specify the host name during installation.

  Published by: user4928701 on July 8, 2011 23:15

  lsnrctl stop

  move/rename listener.ora to new/other file name

  lsnrctl start