speely PC said I have problems 475 is true

Similar Questions

• I ran CHKDSK, the report tells me I have problems with the file system, usn journal. ___

  I ran CHKDSK, the report tells me that I have problems with the sys file. I ran CHKDSK/F, it is said it fixed the problem but I ran CHKDSK again and it shows that the same listed the issues.

  Describe how you run chkdsk.

  That is what the report said: you have problems with the sys file?

  CHKDSK examines the disk space and use of the disk for the table of allocation of files (FAT) and NTFS file systems. CHKDSK provides information specific to each file system in a situation report. The report shows the errors found in the file system. If you run chkdsk without the /f on an active partition command line option, it can report errors because it cannot lock the drive. You should use chkdsk occasionally on each disk to check for errors.

  If you run chkdsk from a command prompt while Windows is running, it can report errors or it may not report errors - and it may report different
  Errors each time you run.  If this is the case, it could just be the way you run chkdsk.

  Here's how Microsoft explains this observation:

  "... CHKDSK may report that the disc is damaged, even when there is no
  current real corruption. This can happen if NTFS happens to modify
  areas of the disc on behalf of some programme activities that CHKDSK is
  review at the same time. To check a volume correctly, the volume
  must be in a static state, and the only way to ensure that the State is
  to lock the volume. CHKDSK only locks the volume when /F or/r (which
  involves the 'F') is specified. For example, you may need to run CHKDSK more than
  time so that it can complete all the steps in read-only mode. »

  If you run chkdsk from a command prompt, you are not the necessary static state and you can encounter errors "when no real corruption is present. This is how it works when you use this way.  Any changes made to a NTFS file system modifies the USN Journal.  If you are not in a static state, your USN change Journal probably all the time, so what you see (says something like that) can be quite normal.

  Two ways to ensure that you are in a static state is to run chkdsk from the Recovery Console or to schedule a chkdsk to run the next time that the system
  Restart by answering Yes to the question:

  Would you want to check this volume to be the next time the system restarts?

  If chkdsk reports errors when running in a static state, the errors should be investigated, resolved or explained.  This may take several
  chkdsk runs all of the issues and some problems cannot be resolved by chkdsk.

  If chkdsk runs the next time the system is restarted, the activity and the result will be displayed in the application event log.  Look in the Application log for
  Winlogon events and a source have the date and the duration nearby time chkdsk.

  It is in fact a chkdsk additional reading if you want to learn about it and it will explain everything you see and why your expectations exceed reality.

  Please vote my posts as helpful so I can get a lot of points. I'm saving for a pony!

• I have problems with my printer, most of the time I get a message saying to start my spooler and when I try it says I have an error any help would be appreciated

  as said I have problems with the printer spooler with the fact that it's the second printer the same problem, it seems to be a Windows related problem

  Hello Martin,

  Try this fix it site: http://support.microsoft.com/mats/printing_problems/ .

  Let me know if this solves the problem for you.

  Kind regards

  BearPup

• I have problems with my Apple ID when you download applications, that it is said that your ID Apple has not yet been used in the iTunes Store

  I have problems with my Apple ID when you download applications, that it is said that your ID Apple has not yet been used in the iTunes Store

  What exactly is the problem? You are also being invited to review the account and enter payment details? If you did you are your details accepted - if they are, you should be able to remove them then.

• Whenever I try to place materials on the House, these materials is placed on the grassy areas. Punch said update my chipset, but I have problems doing that.

  Meeting of the problems with my Punch home and landscape design V17.  Whenever I try to place materials on the House, these materials is placed on the grassy areas.  Punch said update my chipset, but I have problems doing that.  I have Intel (R) g33/g31 Chipset family 8.15.10.1825.  I'm looking for a place to download the latest updates for this system of video card.

  Go to the web site of the manufacturer of your computer.  They should have all the correct drivers for your computer brand and model.  Don't download them from any other place because who could cause problems.

  Good luck.

• Cabinet detects 2 problems during analysis, but in the end that he said found no problem and the only option I have is to click Finish

  I have downloaded Microsoft Windows Malicious Software Removal Tool (KB890830) - to install the CAB file switch and it detects 2 problems during analysis, but in the end that he said found no problem and the only option I have is to click Finish. I tried several times with the same result of detection 2 never, he gets rid of them. Help?

  OT: Malware

  On Saturday, April 5, 2014 22:59:18 + 0000, JChabler wrote:

  Where? I find only free trials to detect, but you have to pay to resolve.

  Go to https://www.malwarebytes.org/ and lower-left button
  corner, one that says "Free download."

• My watermark came before I did the recent update on CC 2015, always when I would export to PhotoShelter.  Now, the watermark does not appear.  I asked PhotoShelter for help and they said they have heard about other problems.  How ca

  My watermark came before I did the recent update on CC 2015, always when I would export to PhotoShelter.  Now, the watermark does not appear.  I asked PhotoShelter for help and they said they have heard about other problems.  How can I solve this?  Nothing has changed on my computer.  Thank you.

  Sharon Cameron

  Hi sharonc,

  Have you tried to reinstall the plugin Photoshelter for Lightroom CC newer version 2015.

  See the below for the upgrade to the latest Version

  https://support.PhotoShelter.com/HC/en-us/articles/203373590-PhotoShelter-s-official-Adobe - Lightroom-Plugin

  Let us know if that helps.

  Kind regards

  ~ Mohit

• I downloaded the "Paretologic PC Health Advisor.exe' and he said: I have several proplems registry, but I have to pay to correct, this is the only way to solve my registry problems?

  I downloaded the "paretologic PC Health Advisor.exe" and he was not able to solve the problems because I had too many and had to buy a license. What is the only way to solve these problems? According to analysis, there are 616 detected items

  Hello

  If you have problems with system start a new thread, and we can help you with those.

  This program is essentially RegCure (another of their products) renamed with a few gimics
  added. He and produced still too hype, are snake oil that causes a lot of
  questions all distressed little. Replace the PC Health Advisor for the RegCure word in the below
  and you'll get the idea.

  I would like to ditch RegCure like a hot potato
  http://www.MaximumPC.com/article/watchdog/is_regcure_legit
  RegCure Review consumer: Forget what others say, is that the words you need to hear
  On RegCure July 2009

  http://www.Docstoc.com/docs/9822187/RegCure-consumer-review-forget-what-others-say-this-is-the-words-you-have-to-hear-about-RegCure

  http://www.articlealley.com/article_1007818_11.html

  Free registry cleaner software - why pay when you can get it for free?
  http://software-Adviser.SynthaSite.com/free-registry-cleaner-software.php

  Seems that these sites that encourage these poor products are all part of the scam. They
  understand a couple or legitimate products (as appropriate), and then note all their products higher and
  they are practically the same.

  Unless you know how to recover from a wandering deletion and which can be extremely difficult it is better to use a registry cleaner. They "fix" very little and 'BREAK' a lot

  Run RegCure uninstaller C:\Program Files\RegCure\uninst.exe

  Check the info here:
  http://www.ParetoLogic.com/resources/help/RegCure/source/uninstall.html

  Or use Revo to uninstall:

  If RegCure is running use TaskManager to close (end) - right click on the taskbar - task manager

  Revo Uninstaller - Free Version
  http://www.revouninstaller.com/revo_uninstaller_free_download.html

  I hope this helps.

• I have problem with my iphone 5 has no 4g 3g only. in Sweden in the works of 4g Malmö... can someone help me please...

  I have problem with my iphone 5 has no 4g 3g only. in Sweden in the works of 4g Malmö... can someone help me please...

  Where did you buy this phone? 4G has already worked on this phone? Whatever the carrier said when contacting you? Have what troubleshooting you tried?

• I have problems to install MSN Zone games.

  From: Choppa

   

  Someone else had problems playing games of www.zone.msn.com?  Given that I put Vista on I can't play one of their games free online.  He begins the game Installer, made up a box asking me to hit the continue button (which I do) and then he said: 'Oops, we don't have install your game.  This happens with all games and seems to be a security setting, but I allowed and turned my safety down, but nothing helped.  Any ideas?

  From: Spot

  You are using Vista or XP? I was able to enter the area games very well under XP with IE7, but in Vista RC1, I have problems as well. So far, I've tried adding msn.com to trusted sites, allowed to jump - rises and msn.com cookies AND run IE7 as administrator to see if this might help with the installation. It froze to the advirtisements before the game for about 3-4 minutes, but seems to work fine now.

  Another response of the community of Windows Vista discussion groups

• I have problems with the installer of Windows and Windows Update, and the solutions that I found for the two each rely on the other broken system to fix the first.

  I use a laptop HP Pavilion dv4-1220us with Windows Vista Home Premium Service Pack 1, a 64-bit operating system, and I have problems with Windows Update and Windows Installer. When I try to install programs, I get the following, or substantially similar message without the error code:

  "Error 1719. The Windows Installer Service could not be accessed. This can occur if Windows Installer is not installed properly. Contact your support team. »

  So I tried to download Windows Installer 4.5 and install it. When I try to start the installation, it always hangs on the first step, "Initializing Installation."

  After searching for a solution to this problem, I found that Windows Update may have a solution. So I downloaded the 64 bit version and got a file named 'file Windows6. 0-KB942288-v2 - x 64. I tried to run this file. He opened a box that said, in order "Prepare for Installation", "Full Preparation", and finally "Searching for Updates ', before you open a second box, which reads" click OK to install the following Windows software update: fix for Windows (KB942288). I clicked on OK in this box, which opened another box, which says at the top "updates are installed" and in a smaller section, "initializing for Installation................... »

  However, no matter how long it works, it never gets past "Setup initialization."... »

  So I tried to run Windows Update in Control Panel. He ran for a while, before giving a message saying "to check the updates, you must first install an update for Windows Update." I clicked on the button that says "install now". He has flashed, a moment, "download and installation of updates' before you go to the"check for Updates"and then he brought back the exact same upward ' to check updates, you must first install an update for Windows Update" message as before. I clicked install now once again, only to go into the exact same loop. After about four times in a loop, I gave up on it.

  So I tried to install Windows Installer 3.1v2, which took a while before saying "not enough memory is available to process this command." and the abandonment of the installation.

  So, I tried to download a program from 'Mr. Fix - it' of Microsoft. It downloaded fine and then failed on installation, because of the same Setup error I received initially.

  Finally, I tried to restart my computer and each solution is represented. Then I clean my computer and each solution is represented.

  In conclusion, the mistakes that I have in Windows Update and Windows Installer cordoned off each other, as the mistakes of each program are based on the other program to be repaired. I'm at my wit's end here. My computer works fine without one, except that I can't install new programs. I can access the internet fine, access files fine, all my scans have developed own... I don't really know what is happening. Can someone help me with this?

  Try the sfc scan:
  http://support.Microsoft.com/kb/936212

  If not, repair of Vista:
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

• I have problems wireless on my Acer laptop which has Windows Vista. I am able to connect to my school of university network and used to connect to my home network.

  original title: Wireless on the Fritz

  I have problems wireless on my Acer laptop which has Windows Vista.  I am able to connect to my school of university network and used to connect to my home network (both are networks limited requiring a password or log in).  However, last week my computer stopped connecting to my home network (no one else has this problem with the home network).  I tried to fix the problem, but my computer says that "Wireless association failed because Windows did not receive response from the access point or wireless router."  That said also thatthe connection "(my wireless network)" has been cancelled.  This is perhaps due to a timeout or user action. »

  The only different thing I did last week was click option at my University 'connect long-term' instead of 'connect short term' to their wireless network.  Maybe who has messed up my settings?  That's what my University said of his record long term: "students, faculty and staff also have an option to easily record their computer (or other wireless devices), so that it is not necessary to authenticate each day they connect from the network wireless campus, to resources outside the University.»  However, these settings are saved on their network (I can access it online from another computer), so I think it is unlikely that he messed up my settings.

  I don't really know what the problem is.  Any ideas as to what I can do?  I don't want to reset my computer everything.

  Thank you!

  Hello

  You can view these methods:

  Method 1:

  I suggest you to disable any program of security on your computer and check if it solves the problem.

  After reviewing the question you must reactivate the security on your computer program.
  Note: Run the computer without antivirus software or firewall is a potential threat to the computer; Be sure to activate security software after completing the troubleshooting steps and after identifying the problem.
  Method 2:
  I suggest also allows you to check in SafeMode with network.
  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
  Method 3:
  I also suggest you to check the settings of the router firewall.

• I have problems with windows update

  Hello

  I have problems with the updates of the window.  I read install my window.  and start the update.  I update well until it installs the update for service pack 2. Once it restarts is said to check the updates, you must first install an update for the update of the window...

  When I click on install update of the stop and keep it on the research.  I have don

  ' t even use all the data.

  I already tried the Microsoft fix it and some troubleshooting aspiration which I met on the Microsoft site.
  (error trouble shoots)

  Windows update error 0x80072efd - not fixed

  recent update - no fixed installation issue.

  Can anyone help me please with her.

  Thank you

  Please provide a copy of your system information file. Type the system information in the search box above the Start button and press the ENTER key (alternative is select Start, all programs, accessories, System Tools, system information). Select file, Export and give the file a name noting where it is located. Not to place the cursor in the body of the report before exporting the file. The system creates a new information file system each time system information is available. You must allow a minute or two before the file is completely filled before exporting a copy. Please download the file to your OneDrive, to share with everyone and post a link here. Normal mode preferred report. Please say if the report was obtained in safe mode. If the report is in one language other than English, please indicate the language.

  Please download and share with everybody fresh copies of your System log and journal of the Application (two files) of your event viewer on your disc one and post a link here. You can delete any previous copies of your OneDrive records.

  To access the system, log, select Start, Control Panel, administrative tools, Event Viewer, in the list on the left of the window, expand Windows logs and select System. Place the cursor on the system, select the Action in the Menu and record all events like (the evtx default file type) and give a name to the file. Do the same for the application log. Do not offer not filtered files. Do not place the cursor in the list of reports before selecting the Action from the menu. Do not clear the logs so that you have a persistent problem.

  For assistance OneDrive see paragraph 9.3:
  http://www.gerryscomputertips.co.UK/MicrosoftCommunity1.htm

  General remarks on event viewer
  http://www.gerryscomputertips.co.UK/syserrors5.htm

• So, my cousins both got two netbooks for Christmas so I took it upon myself to put in place. However, I seem to have problems with getting Homegroup to work.

  original title: incorrect Homegroup password

  So, my cousins both got two netbooks for Christmas so I took it upon myself to put in place. However, I seem to have problems with getting Homegroup to work.

  All computers:
  Have enabled IPv6
  Use Microsoft Security Essentials with the last update
  Are connected to the same router (Linksys WRT54GX2)
  Have no other third-party firewalls or AV installed and have been neatly eliminated via their respective tools when they had their
  Can be seen in the network and can access any other files via 'network '.
  Have the correct date and time and are all in sync with time.nist.gov.
  Have the same network sharing settings (network discovery on, files and printers sharing folders public, sharing, streaming, wide, 128-bit encryption, sharing password protected, to allow windows to manage the homegroup connections)
  Network is set at home, not in public

  The computer that has implemented the homegroup is connected via ethernet to the router while other computers use to access the router 802.11 g I tried to delete and redo the residential group as well.

  Despite all this, it is said that the homegroup password is incorrect for both netbooks (where it says it has encountered an error). I realize that it is case sensitive and I entered the password correctly. I also ran the resolution of the problems of the homegroup on all 3 machines and still no luck. I also tried to change the password and restarting of machines.

  Any suggestions? I was _really_ hoping it will work right out of the box. Maybe it's something with the router? I don't really know. Any help is appreciated. Merry Christmas! : D

  Hello

  check out this link.

  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-create-a-HomeGroup

  http://Windows.Microsoft.com/en-us/Windows7/create-a-HomeGroup

• I have problems with my subscription to Adobe Stock.

  I have problems with my Stock of Adobe account. I tried to update my account for the past few weeks after getting my new debit card, once I noticed that 2 of my stock payments didn't cross it. (I was not on the stock of recent times) I've updated my card, he said thank you, now you can use your account... but it is always as I do not have. I contacted the chat and it reactivated my account charged $ 8,81 on my account and he said: I'm in charge again on 13 February for monthly salary. I even got an email saying that my account has been reactivated. When I went to concede a photo, he brought me to a new page to 'buy' the image, subscribe, ect... as if I don't have a subscription. I had Adobe Stock since last August and should have flight path so pictures since I have only licensed 25 of 40 images. These do not show either. I even tried to buy the week last with her still pending at Paypal. She wanted me to pay $10 plus ($49,95) to subscribe to a photograph of annual Adobe + stock, even if my last year does not expire until April. Certainly feel frustrated here. Is anyone having problems with the subscription?

  Hello

  The distribution of your Stock has been updated.

  Kind regards

  Bev