Spooler subsystem app has a problem and needs to close and... .instructions @ 0x0041003d referenced memory @ 0x0041003d memory could not be read.
I have windows xp svc pack 3. I have 2 printers hp psc 2410, samsung ml2010. I've never had a problem until recently, and now I get 2 messages all the time... the spooler subsystem app has a problem and needs to close and... .instructions @ 0x0041003d referenced memory @ 0x0041003d memory could not be read. Whenever I try to print my computer crashes. I tried to uninstall and reinstall the two printers. no luck. I tried mrfixit and when it comes to the printer part, mrfixit seems stuck in a loop and it is doing nothing more than an hour. no luck. I paid for norton antivirus, thinking it was a virus. no change. paid for advanced system optimizer. no change. Now that?
Hi MarthaForner,
You can read the following article and check if it helps.
Tags: Windows
Similar Questions
-
Spooler SubSystem App has encountered a problem and needs to close. We are sorry for the inconvenience.
Hello
1. When you get this error message?
2. that you get this error message when printing?
3. What is the brand and model of the printer?
4. don't you make changes to the computer before the show?
Please provide us with more information on this issue to help you best.
If you get this error when printing, follow the steps from the link below.
Important: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
http://support.Microsoft.com/kb/322756
How to back up and restore the registry in Windows
-
Spooler Subsystem App has encountered a problem and needs to close
We cannot print anything on my computer. the message is that the Print Spooler Subsystem App has encountered a problem and needs to close. How to get the print spooler to run and work my printer start?
Hi Saeed,
1. were you able to use the printer before without any problem?
2. did you of recent changes on the system?
3. What is the brand and model of the printer?
Method 1:
You can try to start the Fixit from the following link and check if it helps.
Problems printing and printing errors
Method 2:
You can also read the following article and check if it helps.
-
Spooler subsystem app has encountered a problem.
HP Laserjet 1020 printer does not work. Have used this printer for years. Last print job has stopped the printing process and give the spooler subsystem app has encountered a problem error message.
Used Mr. Fixit. Have the print spooler service manually restarted and the RPC service. When I try to print, Spooler Subsystem App Error message appears and printer spooler stops,
OS is XP Home Edition Service Pack 3.
Cannot remove hardware HP Laserjet 1020 and reload HP Laserjet 1020 download did not fix problem.
Often, but not always, the symptoms you describe are caused by a corrupt print job stuck in the queue or a damaged printer driver. However before you clean things up, on general principles, that you can download, install, update and run full scans with each of these two free programs:
AntiMailware MalwareBytes
SUPERAntiSpywareDo not operate the two scans simultaneously. Each will take a long time, so start it and then go do something else for a while.
Cleaning of printers
NOTE: If after completing step has the print spooler is not always running after you launched the command "net start spooler", you will not be able to follow all the steps in "First Article". Use of the special procedure for printers Lexmark described below and follow in its first Article. If still no joy, use the alternative method that is linked below.
A. Clean on print jobs pending
- Open a command prompt window (start > run > cmd > OK)
- Type the following in the black command prompt window, and then press ENTER after each line
net stop spooler
del/q '% windir%\system32\spool\PRINTERS\*.* '.
net start spooler
outputB. clean the old printer drivers and install the latest drivers by using the directions in One Article.
A special procedure for computers that have or had a Lexmark or Dell-badged Lexmark printer.
Open a command prompt window (start > run > cmd > OK)
Type the following in the black command prompt window and press enter
dependent on the spooler of sc config = RPCSS
outputNote that there is no space before the =
If you want to use a Lexmark or Dell-badged Lexmark printer after having done the above, you will need to reinstall it.
Alternative to the method of his first Article: http://members.shaw.ca/bsanders/CleanPrinterDrivers.htm
Use of SuperAntiSpyWare found two serious problems. Could cross printer of pending work. Printer works fine. Thanks for your reply and advice.
Best regards
-
5.7 Lightroom will not import. I get this message: the instruction at 0x17f3f885 referenced memory at... Memory could not be read. This program has been flawless for the past 3 weeks.
Hello
You really need a little more information such as operating system, memory, etc.
Usually a mistake like this happens because a background process is running and interfere with the available RAM, not enough virtual memory (Windows), drivers of HW obsolete or just an incomplete installation.
Or, one of the biggest problems is add-ons in internet browsers.
Alternatively, another problem of Lightroom, no sufficient permissions on the directory where you import image files.
Please provide a little more information.
-
Acrobat and Reader 8. When you try to print, the memory could not be "read".
A user (without local administrator rights) does a job batch of Microstation and exported all his drawings in pdf format. They open correctly in Acrobat 8 and Reader 8. When he clicks on the button print, it gets the error below. When I login with local administrator rights, I can print these accurate pdfs very well. Here is the event/error log entry. Any help would be greatly appreciated. It runs Windows XP SP3.
Event type: Information
Event source: Application Popup
Event category: no
Event ID: 26
Date: 27/03/2012
Time: 17:27:46
User: n/a
Computer:
Description:
Application popup: 2012-03-27 C6-01. PDF - Adobe Acrobat Professional: Acrobat.exe - Application error: the instruction at "0x0436959a" referenced memory at "0x00000d28". The memory could not be "read".
Click OK to terminate the program
Click on CANCEL to debug the program
We tested with another nonadministrator account and Acrobat worked fine. Therefore, the problem was in the user's profile. We just its data saved, deleted the old profile and did reconnect. This has created new profile. Acrobat works beautifully.
-
Original title: the pc startup problem
I can't start my computer hp envy and the notification I receive
Theinstruction at 0x6dcf61a0 referenced memory at 0xe19fa418. The memory could not be read
After I ok this threat my laptop screen will begin to Flash and no action more than I can do except power off.
Hello
Thanks for all, but am confused after a lot of links sent u and also the main problem is that I can't connect to my laptop that I told u im unable to take any action.
The first thing that I advised you to do did not connect.
I suggest you read the advice of HP
Run HP diagnostics:
-
App error: instruction at 0x7c911389 referenced memory at 0 x 00000010 memory could not be read.
Desktop HP Pavilion (a710n) keeps making the message: the instruction at 0x7c911389 referenced memory at 0x00000010. Memory could not be 'read' click ok to terminate the program - every time that the computer shuts down and many other random times. It prevents downloads to install now?
Windows 8 is different from its predecessors. This site contains tutorials for several new features for Windows 8. Once I adjusted to the differences in Windows 8, I found that I enjoyed the operating system. Keep in mind that the Windows 8.1 is available in beta form if you want to see what can come from the changes. If you choose to test Windows 8.1, don't forget to do your first recovery disks, then you can return to a factory State if you do not like Windows 8.1. More information on Windows 8.1 overview can be found here.
-
Error message: Spooler subsystem app has quit working
I have been using Windows Vista Home Basic version for several months. After turning on my computer for several minutes, two weeks ago I received an error message "Spooler subsystem app stopped working. Then when I clicked on the solution put on internet, I was recommended to close this error message. But then another message appeared "Data Execution Prevention has closed.
How can I solve this problem? I have not install new software at all. How is it that I get these 2 posts? Please notify.
My email is * address email is removed from the privacy *.
David Taylor
Hello
Your printer drivers have become probably either damaged or defective. Remove them and install a new download of the manufacturer of the printer. Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org
-
Spooler subsystem app. has been closed to protect system
I ran the program of Mr. fixit from microsoft site. seemed to fix my printer, but my printer seems to work very well, came back, nothing wrong. whenever I turn on my computer I get this message even. Spooler subsystem App and had to protect close system, have no problem closing the message window. Don't know if this is important or how to fix it. Help! Thank you
Yes, I have Windows XP. Well, when I boot message appears and I close the message and I have no problem printing. The list of the icons in the "printers and faxes" are; HP deskjet 5600 series (and the checkbox), Microsoft XPS Document Writer, send to OneNote 2010. I didn't know there is more than one "Mr. FixIt" program, I just followed a link that the error message was downloaded "Mats_Run.printing.exe" and opened it and keep running and it came to a point where he says that something like could not find no problem to solve. Thanks for your help and your patience with my inexperience with this process; never been in the forum before.
I have not seen a situation as you describe it. Usually, when there is a problem and the spooler stops it stays down. Can you identify what happened before this problem occurred first?
Do you use Microsoft OneNote?
Go to printers and faxes
Right-click on the icon for the DeskJet 5600, and then click Properties
Click the Ports tab.
Use the scroll bar and see if there is an entry named "send to Microsoft OneNote Port:" and, if so, if there is a check in the box for this line.
Click Cancel to exit this dialog box.
Do the same for the XPS Document Writer
It might be interesting to check the programs that start automatically when you start Windows. Download Autorunshttp://technet.microsoft.com/en-us/sysinternals/bb963902.aspx after Autoruns full analysis, as shown in the lower left corner, click the connection tab. You'll probably at least three entries associated with HP. Is there something else that seems to be related to printing or that looks like 'suspect' (I know that is vague; if you can't identify something, include its name in your response).
Also take a look at the tab "print monitors. You will probably "HP standard TCP/IP port" and perhaps "PCL hpz3143a. There may also be a port entry Bluetooth printer here. Anything else?
Finally, if necessary, is listed under the tab "Winlogon".
-
That spooler SubSubsystem App has stopped working and was closed does mean?
Spooler SubSystem App stopped working and was closed means. I can't get my printer to print at all. Not even a test page.
Hello
Check with the printer manufacturer for updated drivers and support for known issues.
Check chan seen message here - one of the highest.
fixed spooler subsystem app stopped working
http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e===================================
If the above didn't help:
Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
the latest driver).Check Mr. Fixits here and if you use the other methods go back and try again later.
Problems of print and error - a Mr Fixit of printing
http://support.Microsoft.com/GP/printing_problemsSolve printer problems - a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx------------------------------------------------------
Logon as administratorStart - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN
You can copy and paste each line except those brackets and press ENTER after each.
net stop Spooler
(echo suppression of all print jobs)<-- you="" should="" see="" this="">
ping localhost n 4 > zero
del/q %SystemRoot%\system32\spool\printers\*.*
net start Spooler
(sound Done!)<-- you="" should="" see="" this="">
ping localhost n 4 > zero
Another way
http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspxIf you use Control Panel - Classic - printers
Try after unplugging your printer if necessary.
-------------------------------------------------------------Also check the spooler print and its dependencies and addictions Service.
The value of all Services back to their default values.
Start - type into the search box-> Services find top - make a right click on - RUN
AS AN ADMINISTRATORBlackViper - for Vista SP1 - Services - all return to their default values.
http://www.blackviper.com/2008/01/28/black-vipers-Windows-Vista-Service-Pack-1-service-configurations/#more-3020BlackViper - for Vista SP2 - Services - all return to their default values.
http://www.blackviper.com/2009/05/31/black-vipers-Windows-Vista-Service-Pack-2-service-configurations/#more-2991How difficulty Windows Vista print spooler starts do not
http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html------------------------------------------------------------
Check this thread if necessary - to stop and erase the spooler
------------------------------------------------------
Clean the General corruption and repair or replace the damaged/missing files.Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228CheckDisk (chkdsk) runs at startup.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
Spooler subsystem app has to stop
I've used two different 'fix it' programs on the application subsystem spooler who said he fixed it, but it will maybe print once and then comes back to the same problem. Help!
Hello
Check chan seen message here - one of the highest.
fixed spooler subsystem app stopped working
http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e===================================
If the above didn't help:
Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
the latest driver).Check Mr. Fixits here and if you use the other methods go back and try again later.
Problems of print and error - a Mr Fixit of printing
http://support.Microsoft.com/GP/printing_problemsSolve printer problems - a Mr Fixit
http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx------------------------------------------------------
Logon as administratorStart - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN
You can copy and paste each line except those brackets and press ENTER after each.
net stop Spooler
(echo suppression of all print jobs)<-- you="" should="" see="" this="">
ping localhost n 4 > zero
del/q %SystemRoot%\system32\spool\printers\*.*
net start Spooler
(sound Done!)<-- you="" should="" see="" this="">
ping localhost n 4 > zero
Another way
http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspxIf you use Control Panel - Classic - printers
Try after unplugging your printer if necessary.
-------------------------------------------------------------Also check the spooler print and its dependencies and addictions Service.
Print Spooler service
http://www.blackviper.com/WinVista/services/Print_Spooler.htmHow difficulty Windows Vista print spooler starts do not
http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html------------------------------------------------------------
Check this thread if necessary - to stop and erase the spooler
------------------------------------------------------
Clean the General corruption and repair or replace the damaged/missing files.Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228CheckDisk (chkdsk) runs at startup.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it=""> -
Printing error: "Spooler subsystem APP has encountered a problem and needs to close."
Original title: cannot print to the network printer.__I have a net wifi Windows XP, SP 3 and an IBM laptop.
Printers seem to be installed (XP has the printer connected via USB) but when I try to print from IBM I get an error as follows:
"Subsystem spooler APP has encountered a problem and needs to close."
The printer is a HP Deskjet D2660 and the LAN is configured correctly by using the wizard.
I also discovered that the print spooler is never started.
In addition, even when I start the spooler it remains not said during the next time I start up.
Can anyone help? I've been banging my head for two weeks.
Salvation;
Thanks for responding.
My IBM ThinkPad running XP - Pro
My computer is a DELL and running XP-Home Edition
Printer installed on DELL
I have a WIRELESS LAN installed by the installation wizard. The net works fine except for the printer.
Every time I start the spooler does not work. If I set the spooler of runing the choice is never registered. the next time I start up, the spooler does not work.
I finally asked some experts to solve the problem of no access to the network printer. It took them more than 4 hours (for a cost) to make it work. Everything was going well until the next day. The problem is back. My thought is that the register should be updated so it will retain the corrtions.
I downloaded the MATS_RUN.printing.exe utility. It corrects everything except this message on the Spooler subsystem.
Any advice you can give me would be greatly appreciated.
-
Spooler subsystem app has encountersd a problem and needs close__
Spooler subsystem has encountered a problem and needs to close
Spooler subsystem has encountered a problem and needs to close
-
Adobe flash plugin is still crashing. I reinstalled 3 times today and a little while later it crashes again.
Message reads Windows\system32\WINSTA.dll C: is not designed to run on windows or it contains an error.
Try reinstalling the program.
So I do, and I did, read a bit on internet to see that others have the same error and I thought to upgrade to windows 7, as it's almost time to do so if I see that people have same problem with windows 7 and this plugin.The question did not get resolved or is there a solution that I have not yet found
Hello
Try with the new user account.
http://Windows.Microsoft.com/en-us/Windows-Vista/create-a-user-account
try to uninstall and reinstall the Flashplayer completely from the BONE and check out them.
http://helpx.Adobe.com/Flash-Player/KB/uninstall-Flash-Player-Windows.html
Maybe you are looking for
-
Download HP Mediasmart software for win 7 64 bit
Hey, I have windows 7 64 bit and I need to download the mediasmart software because I I had vista before and I had to do a custom installation. I had no backup of the software discs and wonder where to download this software because I can't find a li
-
How can I move a rock blues album
How can I move an album from one genre to another, example Blues Rock?
-
Qosmio X 770-exchange of graphics card
Hello! I have a question - is possible to change the graphics card in this laptop? I wonder about it, cause I use this laptop instead of 3D modeling, in games and in this situation programs like SolidWorks inform me that my capomuter (graphics card)
-
mail splitter bar on the right is blocked can not view individual emails without double click
mail splitter bar on the right is blocked can not view individual emails without double click
-
problem to format lenovo A7000
I have format my phone by pressing the power + volume up key by choosing the wipe data / factor reset. But after Chinese update frimware, the formatting in the language menu. So, I do not understand. Please help me... Thank you..