Similar Questions

• After the charge of the desktop, I get a white screen and can't do anything.

  After the charge of the desktop, I get a white screan and can't do anything. It keeps loading of other programs with just the white screan. When I hit CTRL ALT DELETE, my office appeared then disappeared. What can I do?

  Hi David,

  You meet a white screen on startup.

  Step 1: Check if the problem persists in safe mode

  A description of the options to start in Windows XP Mode

  Step 2: If the problem not in safe mode then put the computer to boot.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  Note: follow step 4 to reset the computer to start as usual after the boot process.

  Hope this information helps.

• Two iPad no current charging toward the high wen sign battery Home key and top can anyone help

  IV bought HI two iPad today the third party has obtained said there was no current charging Iv tried 5 charger Chargers work Iv reloaded a couple time, but nothing happens no battery sign on screen Iv don't hold the "home" button and the top button took to a phone store today and was told that they do not need new battery and told me to keep accusing them all two up anyone can help it iPad and Ipad 2 3 someone can help me pleas I thank you in advance

  The leave it plugged to charge all night. If they still fail to hold a charge, they have bad batteries. I'd return them if they don't charge.

• Edge 14. Battery not charging after the Power Manager Update to 6.07 and resetting the battery.

  My battery will do not, at all.

  The gauge was obviously wrong to happen very quickly after reaching 20%, so I've updated the power to 6.07 Manager and then perform a reset of the battery (I'm sure it's in that order, perhaps first reset).

  After resetting the battery charged to 100% back, but as it is discharged, the charger was not.  With the power, the battery is located just at the same percentage and descends very slowly (about 1% in two days).

  I tried to play with the parameters of maintenance battery, the meter then said that charge will begin less than 80%, but the battery is already on the 20%.  I checked the firmware in the Manager of power and with the stand-alone program but apparently no update is necessary and T 42, 4755 FRU part number is not listed as needing an update.

  Current version of the firmware: 3f98-0004-0160-0130

  I tried uninstalling and reinstalling Power Manager.  The power windows manager also seems to have the same problem.

  I just baught the laptop last year, is a month out of warranty; I need it to be portable to work.

  I thought about buying a new battery, but it seems to be the charge function is not working, and the battery was working fine before the reset and the update, apart from the loss of certain abilities and the inaccurate meter.

  Product: 0578CTO Thinkpad Edge 14

  BIOS: 80ET61WW (2.01)

  Any help would be greatly appreciated.

  Nathan

  19% and declining

  Hi NINE.

  Thank you for hospitality, the effort and the answer.  Greatly appreciated.

  I tried this and just tried to reinstall the firmware of power management.

  I finally solved the problem after reading this post by:

  1 shut down the computer.

  2. unplug the power supply cord (and everything - usb and monitor cables).

  3 remove the battery.

  4. play with the spring on the battery switches and shake threatening (probably unnecessary, but you may want to give it 10 to 15 seconds on the laptop).

  5. replace the battery in the laptop.

  6. connect the power cord.

  7. start the laptop and connect.

  Thanks again.

  Nathan

  48% and load

• Using results of actual rate clock by error 'the specified resource is reserved.

  Hello!

  I use DAQmx 9.8, win10 x 64, NI 6221 emulated Council, labview 2012 32 bits.

  I need to define the AO sample clock frequency, check the actual clock rate, calculation based on the new value of pulse rate and write it in the jury for the output. The code example is attached.

  Everything is ok, when I use the command as a timing (as people used to do) during the installation of the task, but when I am trying to set the clock frequency, then number of samples I get "error-50103 that is reserved for the specified resource. The operation could not be performed as indicated. The error occurs after DAQmx Write.vi. I tried to use two calendar controls or a combination of timing and order property node timing with the same result.

  Is that it has no idea how to solve this problem? Probably, there are some more convenient way to get real rates that I don't know.

  I him have not tested yet on real hardware, emulated alone on board.

  Finally, I dindn can't reveal the source of the prolem. It was certainly not related to the synchronisation screw. Just more simple configuration of analog output generated the same problem in this VI, but working without errors when copied to the new file.

  Rewriting all of the project from zero contributed to y for remedy. Initially, I tried to change the existing program of someone else to change the generator stand-alone benchtop to DAC signal generation.

  Now, everything's fine. Due to the software is not complicated it only takes a few hours to rewrite

• Error loading GPS engine. Flight pLan will not be used.

  In Microsoft Flight Simulator X, when I create a Fligh Plan this message: "error loading GPS engine. Flight plan will not be used. "I tried to delete old flight Plans and to create new ones, and re - install the program, but both of these solutions worked.

  Thank you very much
  Martin

  Hi Martin,

  Thanks for posting your query in Microsoft Community.

  According to the description of the problem you are facing problems with Microsoft Flight Simulator X and when you create the Flight Plan this message "error loading GPS engine. Flight plan is not used.

  It is probably because your default flight is based on a situation after a completed flight. Flight data contains a reference to a flight plan, but the plan is placed at the airport of destination, rather that the same departure of this plan and the GPS becomes confused.

  The message is harmless, but to get rid of him, all you have to do is set up a new flight to the way you want it to be, without create/open no matter what flight plan and save this flight as the default flight.

  In fact, all you have to do is back up your default flight one immediately after.

  I would also ask you to contact the Support of X for Microsoft Simulator for help on the issue:

   

  Support Microsoft Simulator X

   

  http://www.Microsoft.com/products/games/FSInsider/tips/pages/default.aspx

   

  Hope this information helps. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• run the vba without compiling vi gets error 13 type mismatch

  Hello

  I am trying to use VBA to access Agilent 33250 vi driver code.  I followed the examples in the forums, but I'm not sure why I get "Run Time error 13' type mismatch.

  Void LabVIEW()
  Protected String filepath
  Dim lvapp As Application
  Dim vi VirtualInstrument
  Dim ParamNames (0-1) As String
  Dim ParamVal (0-1) have varying

  Set lvapp = CreateObject ("LabVIEW.Application") ' create the connection to labview
  FilePath = "C:\Program NIUninstaller Instruments\LabVIEW 2013\instr.lib\Agilent Output.vi Series\Public\Action-Status\Enable 33XXX.
  VI the value is lvapp. GetVIReference (filepath) ' load vi

  ParamNames (0) = "VISA resource name.
  ParamNames (1) = "activate the output (T: Enable).

  ParamVal (0) = "GPIB0::10:INSTR".
  ParamVal (1) = True

  VI. FPWinOpen = True
  VI. call ParamNames, ParamVal

  lvapp. Quit smoking

  End Sub

  Any suggestions?

  Thank you

  I never called LabVIEW in VBA.   But I do not know LabVIEW and I do not know VBA.

  I see one of the two possibilities

  1. the string for the name of the resource does not work for the VISA resource setting or the Enable parameter do not like the real.

  2. are there that many order entry?  Do you need to assign a parameter and a value for each control on the Agilent VI?  I do not know.  Perhaps the VI guess just the default just as if you put a wire into a Subvi.

  # 1.  Break the smaller code.  First of all, just to make the VISA resource and comment the Enable parameter and value.  Then try again with the resource VISA and guided value and assign the parameter enable (0) and value (0).

  See if that one or if these two still triggers the error.

• Locking XP! error "the system could not log. Make sure your username and domain are correct, then type your password again.

  Original title: Locking XP!

  I tried to read all the relevant messages and walked the Earth for this solution, if someone could help me I would be grateful.

  A dear friend died and I got his PC - a fast XP with SP3 which (elderly) she only used for web & email. His account has been "Judi".

  I noticed a while back that, on the logon screen, that there is another user called 'Fiona' (she told me an old co-worker who probably stayed with her).

  Now a friend in need of a very old HP PC Lions not having completely fortunately I managed to copy his files before he was insane - I offered this newer PC it after that I have "set up" for him.

  I put a new account in place on this new PC "Ken" has been added. Then, after the deletion of accounts Judi & Fiona, I cleaned the machine with MalwareBytes, CCleaner & defrag.  All is well now with only Ken appearing on the screen logon (with an image of the appropriate icon), that I used several times in the implementation of his e-mail account and move its acrossetc files. His password is empty.

  Being the only user now Ken, I thought that it strange would its user (only) one click each time to the 'Log in', so I searched and found a box that said something to the effect «... do not show a picture of connection...» » .  That started my problem!  Removing his login "icon" brings ONLY the following - FIONA!

  When connecting a Logon Message now says "the system could not log. Make sure your username and domain are correct, then type your password again.  Letters in passwords must be typed using the proper case" the choice for this error message is 'OK', which takes you to a login screen 'Type Win98' older Classic looking (no icon user) who was behind this logon Message, with (name) Fiona appears on the login screen (former) (full name and empty below the password) , with the choice to enter the password or a stop!

  Of course the password cannot be guessed (Yes - tried blank, admin, etc.) so the only choice is to stop.

  VA F8 at startup for 'Safe mode' goes to screen black WITH Fiona login screen as usual safe mode above and booting with the CD using NTPASSWD shows the usual 1) Administrator 2) 3) invited Ken and 4) Support Microsoft - NO FIONA is shown - and I put all these passwords to 'empty '. Of course repair and recovery repair 'R' does nothing on the removal of Fiona

  This translates the original message & Fiona connection again.  How can I return to screen "image icon" connection without losing files and mail Ken Ken. Where Fiona could hide when it is not a USER of the NET?

  Yet once again, I'd appreciate any help. Brian.

  You should be able to just select (click on) "Fiona", press the delete key, and then type any desired account name.  It doesn't work?

  If you cannot type on "Fiona" in the logon window, you can use the following procedure to modify the Windows registry... or you can take the computer to an independent repairer and ask them to fix it for you.  Don't go to a chain of stores, as a "geek squad" or BigBoxStoreUSA type of place.

  Go here--> https://www.raymond.cc/blog/how-to-edit-windows-registry-key-values-without-booting-in-windows/

  Choose method 1 or method 2.  I'm familiar with Hiren (method 2), but not with the program described in method 1 (even though it seems simple).  Any ISO file you choose, I suggest to download and use ImgBurn (free) to create your CD bootable from the downloaded ISO file.

  The registry key to change is in the same place as "userinit" (which is the example used in the article), so to follow 1-5 step method or method 2 for step 7.

  You will be at HKEY_LOCAL_MACHINE\Software\Microsoft\Windows NT\CurrentVersion\Winlogon

  In the right pane of the registry editor, you will see a large list of items.  Scroll down the page until you see LogonType and double-click it.

  In the "Value data" box, type 1, and click OK (1 is the same either hexadecimal or decimal).

  Close the registry editor, take the CD from the drive and reboot.  You should see the Welcome screen when Windows restarts.

• I get an error message saying: "command line option syntax error. Type the command /? assistance. "

  I'm running Windows 8 preloaded on Sony Vaio and when I try to install the latest update for Atheros Bluetooth Driver Quelcomm, I get an error message saying: "command line option syntax error. Type the command /? assistance. "

  Help, please!

  I followed your instructions, I did not read the comments below first, I change the TEMP and TMP to C:\Temp, it's ok to forget it or do I needed to switch back? But I forgot to copy the original. If I need to change it back, can give me the original code to stick it on the TEMP and TMP, I use Sony Vaio sve14128cb WIN 8.1. Thank you for helping me.

  Dear all,

  I got other way to solve this problem, and it was mentioned by Mr. Vijin.

  If I'm not mistaken, the error message will be show after you go to update your driver Qualcomm Atheros Bluetooth Vaio update version.

  My way is very simple and maybe you can give it a try. Just go to the Google Web site and key in the version that you want to update. Please select the site Web is Sony's main page.

  Or you can visit the official site of Sony for your country, go to 'Support' and key in the version on the area of research and research.

  You can try link below also but I bother it's a newer version for your computer.

  http://www.Sony.com.SG/support/download/554324

• Message error "the preconfiguration file has the wrong type of preset."

  I try to import the Preset brushes for newborn photography.  They are. Irtemplate files. I'm going in in my cc in Lightroom Develop Module, then opening presets Panel and hover the cursor over the user Presets.  I right click and choose "import".  So I find the real. The Irtemplate file and then click Import.  What I get is the above error message «the presets file has the wrong type of preset.»  What I am doing wrong?

  Predefined live (Windows): C:\Users\User Name\AppData\Roaming\Adobe\Lightroom\Local of adjustment presets.

  Presets to develop 'Global' live in: C:\Users\User Name\AppData\Roaming\Adobe\Lightroom\Develop Presets.

  Find your presets in the "Lightroom" file folders (similar to above) tab Preferences dialog - Presets > [show Lightroom Presets folder]

  Manually copy & paste your .lrtemplate files to the appropriate folder and restart Lightroom.

  Note: The folder [develop Presets] can tolerate and allows subfolders, the folder [Local adjustment presets] cannot.

  If only in the folder [Local adjustment presets] .lrtemplate files.

  

• ESX 3.5 U4 - VCB error "another error: the requested name is valid, but no data of the requested type was found."

  I am running the following commanline...

  'C:\Program VMware Consolidated Backup Framework\vcbmounter.exe' h vimlab.ourdomain.com u Administrator password - a 192.168.1.104:winxppro01 - r C:\mnt t fullvm Pei

  2010-03-23 01:00:52.921 "BaseLibs" 3448 info HOSTINFO: See Intel CPU, numCoresPerCPU 1, numThreadsPerCore 2.

  2010-03-23 01:00:52.921 "BaseLibs" 3448 info HOSTINFO: numPhysCPUs is 0, bumping at 1.

  2010-03-23 01:00:52.921 "BaseLibs" 3448 info HOSTINFO: numCores is 0, bumping at 1.

  2010-03-23 01:00:52.921 "BaseLibs" 3448 info HOSTINFO: This machine has 1 UC physical and carrots 1 1 logical processors total.

  2010-03-23 01:00:53.687 "BaseLibs" 3448 info Using the libcrypto, version 90709F

  2010-03-23 01:00:53.687 "vcbMounter" error 3448 Error: Another error: the requested name is valid, but no data of the requested type was found.

  I'm still new to VCB, so I don't know technically what I do. The vmdk files reside on an iSCSI Lun and I point the Server 2003 Windows VCB to the LUN using the MS iSCSI initiator and he see LUN. It see it as "Healthy (Unknown Partition)", but it see IT. My guess is that it should be able to see the files in the iSCSI LUN?

  Anyway, just my SWAG (Scientific Wild Ass guess).

  Using the '-san m "switch gives the same.

  Any help on this is appreciated. I'm just trying to do a full backup of a virtual computer.

  no doubt the '-a ' option does not. You must use it as '-a name:

  Marcelo Soares

  VMWare Certified Professional 310/410

  Master virtualization technology

  Globant Argentina

  Review the allocation of points for "useful" or "right" answers.

• Duplex charger HP 8620 document Mac error - 'the scanner could not complete the scan.

  Hello

  When the analysis attempted double helped since the document feeder, I get the following error:

  the scanner was unable to complete the scan

  If I don't select duplex option, the printer scans very well. I really need the duplex feature was that the printer was purchased for.

  I uninstalled the printer, reset and all that gubbins.

  my setup is the following, configure the printer as wireless on mac osx mavericks last generation last drivers/HP utility. Ipgraded for the latest firmware of the printer also. all without success, and now support is not open until Monday

  For more information on this...

  So I think that I managed to fix it. Different solutions etc. then forums all about I thought I would include it here. This is the steps that I found to work for Mac OS x 10.9.

  I need to follow the steps:

  1. Remove the power cable while the printer is turned on wait about 15 seconds and plug it in again.
  2. When the installation of the printer using the selection HP not the Airprint, which is added by default on Mac OS x 10.9 - capture screen attached and operating.

     

     If everything is working great and then if not go to step 3.

  3. If the printer is already installed with AirPrint go to the printer main & scanners, right click in the box on the left where you printer is displayed and click on reset printing system. -This will remove all printers found here also.
  4. Download of the latest version of the software for your operating system
  5. Install the software, restart the computer.
  6. Download the latest firmware, if it is available for your printer
  7. Add your printer and follow the steps 1 & 2. It should work and allows you to copy double-sided.

  Don't know if this is a limitation of the software or drivers but ADF allows up to 300 dpi, as the manual scanner allows all the way up to 1200 dpi.

  See you soon

  Ed

• USBOTG and Charge at the same time on Stream 8

  To keep this thread as productive as possible and efficient for those who find it useful to:

  Unless you have under your eyes

  1. a schematic representation of the 8 Stream USB port (USB port and battery electric circuit etc.)

  2 source code for the firmware BIOS and kernel that controls the material

  Please DO NOT respond or say "is not possible".  In view of the above is true, you do not have enough information to say '' not possible. ''

  If no one replys with a solution, what he calls not possible by default.

  Also please do not answer to say ' I don't know how "or" but I know how to do anything else that ' is also not that useful.

  An update of the BIOS or other software update may be required by HP, Microsoft or both to offer this feature really intuitive and quite possible.

  And I hope that this thread can be an effort consolidated by all who have the 8 flow to make the necessary changes.  The majority of the other tablet PCs are capable of it.  It seems that only the 8 Stream and a few others have trouble with her.

  ~~~~

  I want the ability to use a simple, inexpensive cable and perhaps standard (with electronic active minimum inside) which allows me to host and to use one or more USB devices on the Stream via its USB port B microphone 8 while this cable can also be connected to a charger standard and charge 8 flow simultaneously.  This means that the cable has a minimum of three connectors.  One of the possible configurations are as follows (apart from the normal charging cable):

  1 cable Micro USB B Male - connect to the stream 8

  2 USB male A - connect to the AC charger (IE one that came with the 8 Stream)

  3. USB A female - one or several connectors to plug into the key of USB data, keyboard, mouse or even a hub.

  Connector # 2. above shall provide a power supply to recharge the 8 Stream via conn. #1 and the power supply for external USB devices via conn. #3 so that they are in use - all at the same time.

  A and if the same cable can act as a normal OTG no charger for when no external power supply is available.  This may necessitate a switch or an electrontics active inside.

  The last part of this goal is unimportant for various reasons.  I wish that HP, the manufacturer of 8 flow, to State in writing good mode necessary to do this, so that other manufacturers or even-it yourself can make maximum use of their tablet HP equipment.

  ~~~~

  The neat thing it will alow a person to do with their tablet, it is to work at home using the Tablet as a desktop PC by connecting a keyboard, mouse, perhaps external screen (with USB to the display adapter) and knit for a long time without time limit prescribed by the battery life because the charger provides energy to all involved.

  If there is only a single connector on the cable #3, then an additional node of coarse had to provide support for these multiple USB devices at the same time.  However, it would be better if there were several #3 connectors integrated in the cable itself.  This would be better as a suitable USB hub also requires its own power.  That an adapter is necessary if the whole thing were integrated into one.

  ~~~~

  I really want answers from anyone who has already accomplished USB OTG delivered with simultaneous load with flow 8. (independent of any published 'proper' way is also welcome)

  Today's date is 2015-01-16.  If in 2015-02-16 (one month), nobody has posted a solution and then starts to bug HP and Microsoft on it's us?

  ~~~~

  Technical training:

  I understand the possibility the tablet software and firmware must take a decision on the manner in which power flows on the power port USB microphone B pins.

  I know that with a proper design of the electronic circuit carring these signals of power inside the Tablet could be sensitive to what is connected and without risk to decide for himself what to do without needing to control software.  For example by testing/detecting periodically differential voltage or current management to see what sides of the connector can supply.

  But this is only one of the many "could bes".

  In addition, this can be no standard regarding the standard USB.  What seems to be actually the case with a lot of cables OTG + fresh, is that physical clues embedded in the cable or charger are used to signal to the Tablet what the situation is.  Then the signal of software/firmware of the Tablet, interprets what the situation is intelligently and responds by flipping the bits of correct hardware control to activate, or deactivate the power flow in the port and also control its direction in or out.

  I'm not familiar with the standard USB.  Maybe I could do more research, if I believed that HP followed with 8 Stream or even the standard covered this situation explicitly.

  But to a certain extent, it seems I'll have to invent something that should be intuitively just like it does with other tablets. Isn't it?  Maybe I'm overthinking, but I can't find any USB OTG + cables load that specify compatibility with 8 HP flow.

  In any case, I was familiar with both methods other use of tablets to send the highest mentioned signal to the hardware/firmware/software of the tablet to the idea that it's time to load / time of OTG or both.

  The first method is a 0 Ohm to 200 ohms short between pin USB A 2 and 3.  This is the bidirectional data differential lines D - and D + respectively.  In data mode, all the data passes back and forth on those lines.  When you load with a cable, it's the charger module that puts this short, not on the cable.  I measured the short on three different Chargers.  It is 0 Ohms on two of them, one of those who are the charger that came with the 8 HP flow.  The others 0 ohms was generic.  The third was for an apple iPad and it measured on 53KOhms.  It's probably not the resistance ohms 0-200, but probably it is impedance termination indicating that there is some intelligent serial port communication in the charger itself.  Leave it to Apple to be different.

  This method is somewhat questionable, as this signaling mode would prevent OTG + fee because it seems unlikely that you will be able to OTG when the data lines are shorted each and overloaded with such low impedance.  I could be wrong on this subject...

  The other method I have seen suggested to work with some tablets and phones other than the 8 stream is too short the USB microphone B pin 5 to Terminal 4 with 0 Ohms to 100 000 Ohms.

  USB B has 5 pins.  USB has only 4.  The extra pin on B moves the GND pin 4 pin 5 pin to and makes pin 4 PIN ID.

  If this signal applies to a drop in the ID pin (4) or in some cases, I saw that she proposed, he runs down with 0 Ohms.

  Dead shorting things always makes me nervous.  If ID is a simple normally high impedance high input, resistance could be used to make voltage well below the low or zero threshold while also preventing the risk of damage when cheat on him with a device that you do not have the diagram for.

  Yet, 100K is a bit high for a 'pull down' in most of the situations that I'm used to.  Even a 10K would be uncertain. A 1 K or 2 K seems reliable enough, but then things are weaker and in know more nowadays low...   All but a dead short but if possible.

  So, it seems possible that the device might be able to "indicate" by the specific value of the resistance, which can be found here.  In other words the resistance is not a pull down but in fact a signature analog ID, in which case the exact value will be crucial. So if this is the case, a guess is not going to work.

  Obviously in such a system as described above, a chip inside the Stream 8 should be responsible to support this information. I hope the 8 Stream has such a chip.

  Probably a register inside this chip would be at all times what the State of the pin ID is a binary number.  All that is needed is for the BIOS to the chip and the registry in it and read this number via the bus to determine what happens to the port. Finally, he would use that signals of info to send the order of material to the electrontics of power set the appropriate direction to take etc.  (and change the State of the icon on the screen of the rude)

  I don't know if the PIN ID method described is a standard USB or not either.

  Eventually, there may be a third way. But I do not suspect that it would be possible with a non-active external device. In any case too complicated for the novice DIY for sure.

  The device would need to act is a kind of extension of bus.  As an active hub.  But she would use the negotiation of data USB serial lines and in addition to reproduce one or more additional USB ports, intelligently inform the tablet to get with the program which is "now we're going to otg and recharge at the same time."

  This requires a smart external device with a processor Inside, no doubt.

  It seems to me that many other tablets have been able achieve avecjoint here the need for a smart external device and thus the flow must also be able to do.

  There is a device that claims to be able to work with the HP Jet 7 and 8 and provides same ethernet and USB and big DVI ports so loads the data stream.  But its expensive because it is active.  Se here:

  http://AMZN.com/B00OVDE0GC

  It's called a "Docking Station".

  A reference to a product that does exactly what I want (possibly without active electronic components) is here:

  http://AMZN.com/B00LTHBCNM

  It's by Kirin and it is a device of type squid with four USB ports.  Precisely, which is my goal.  But read in the comments stream 7 user indicated that he would not be OTG and load, not really clear if it worked as a hub USB OTG or not.  Another evaluator stated that she would not support even a single USB device much less fees of 8 Stream.  This device has a switch.

  I forgot to mention that some 'hackers' have claimed success with other tablets to deceive their devices by using a multi-step process to plug things in.  Usually in general they would get connected Tablet and load first, then they would return a switch or something remove some resistance or the signal was introduced by the first position of the switch. For some reason any Tablet would continue to require. Then the data lines would be free and they would plug in a usb key and it mounts correctly even if the tablet was always in charge.

  It's like the power circuit has a lock which does not allow it to return to the mode "power flow" as long as he still feels the power flows inward regardless of what software it is telling.  Full proposal here.

  These tips seem dubious to me.  Changes in the BIOS could change the way it works.  Also you can not be sure what actually happens if you do not have a schematic representation.  You could damage your tablet.  Many people will support icon in the operating system whether the Tablet is in charge.  But I'm sort of a low-risk guy and my policy is generally indicators of intereperet not to have meaning at all once a device is functioning in a non-standard setting.  Especially when it's something that I did not built and could not fix if I FRY.

  Hypothetical reasoning: tell me what data sensory discs really the State of the charging light screen?  This reflect the bit of hardware control programs actually feeding management and status on the port?  Or does it measure the direction of the flow of power, said in the section of the circuit battery monitoring?  Point - none of us have a schema because it's owner. To really be sure according to the smart electronic hardware, the port must be mode flow under advisement "of power. If it's in a "power flow out" mode and power will be delivered externally as well you wind upward with both power supplies the same power at the wheel nets.  In this case, the two opposing regulators attempting both to drive 5 V can have slightly different voltage calibrations.  That could lead to fighting between them, with more than 100% of their capacity.  For example if you try to regulate 4.95 real V and the other and other attempts to regulate 5.05 V.  Current then flows to the tune of 100 mV / a few milliohms in the cables linking the two.  This may be several amperes. (many)  In other words, like I said: you want the tablet to know that power is coming in don't go out and automatically hitting the internal switches needed for that to happen. Probably the icon should indicate this with precision, but in some wacky situation, he could not. There may be a chance that the icon could indicate the load and still be burning or focusing on some circuits of the tablet or the charger.

  Another thing, I could see that happening is if you play with these reported resistance types enough you might find a resistance value that winds up place the device in an intermittent condition.  In other words it keeps flipping back and forth quickly between OTG and fresh.  It can give the illusion that it works.  You can have marginal communication with your USB devices and battery could even load.  But will still be a lot of stress on the power circuit.

  It is difficult for me to risk a Tablet perfectly well if I don't know exactly what I'm doing.

  If a brave individual makes their own experimentation and verifies that it charges and OTGs and you tell the rest of us, you're a hero.

  Maybe one of you has a good knowledge on the USB standard to have more confidence in such an experience... like what the ID pin 4 REALLY supposed to work for example?

  That's what I know so far.  If you think you can help, thanks in advance, or if this helped you, then your quite welcome.

  It works

  http://Accessories.us.Dell.com/SNA/ProductDetail.aspx?c=us & l = to & CS = 19 & SKU = 470-abes & baynote_bnrank = 0 & baynote_irrank = 0 & ~ CK = baynoteSearch & dgc = CJ & cid = 47997 & lid = 4279734 & acd = 10550055-4485850-eb75dcb47e53437680ed323a1f4885fe

  Evidence

  http://targusblog.com/2014/11/25/how-to-turn-a-99-Tablet-into-a-workstation/

  But it's 4 x the price in Europe

  Have fun

• Windows 7 reactivation error "the product key you entered cannot be used to activate Windows on this computer."

  Original title: the reactivation of Windows 7.

  I had uninstalled my Windows 7, or more to the point, to the format that cause hard drive then I bought a copy of Windows 7 Professional 64-bit and tried to install it on my new hard drive 2 TB, but it is around. But now four to five months and this disc hard seems to have failed, the installation going crazy and ends by not completely. So now I use 8 64-bit Windows, on the hard drive that's used to have my old Windows 7 32-bit, and I try to install Windows 7 32 bit on my VMware Player as a virtual PC, but for some reason any bloody, the thing won't turn on. I got my license and my old Tower, the old tower and the old series of hardware Linux now without all the graphics cards, but it is going to be really just a supermodel, a server for a game and accommodation of the tracks that can be downloaded in the game, all she needs a new motherboard cheap as the motherboard, that he completely fried. But the issue I'm having is with virtual PC, however, I use the license that came when I bought it and is not wanting to turn on, it keeps Gush a BS error, my Windows XP is activated, but my Windows 7 does not. He always tells me that "the product key you entered cannot be used to activate Windows on this computer."

  How and why? I'm in my series that accompanies it, and that's exactly as it appears on the label. What I am doing wrong?

  Have you tried to restart by phone?

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

  If your license of Windows 7 is an upgrade:

  However, the requirements for the media upgrade is that you have an operating system already eligible such as Windows XP or Vista installed to use it. Since the Windows 7 end user license agreement.

  15 UPDATES. To use upgrade software, you must first be licensed for the software that is eligible for the upgrade. After the upgrade, this agreement takes the place of the agreement for the software that you upgraded. After upgrade, you can no longer use the software that you upgraded.

  So, if you are always denied, you will just have to reinstall Windows XP or Vista and let it do the verification of eligibility.

  --------------

• Error: The action cannot be completed because the folder or in a folder that it contains is open in another program.

  I get this error message when trying to update the folder on shared drive names (affiliated company)

  Hello

  What is the drive shared access by multiple users?

  I suggest unanimous the computer connected to the part and try to edit the file from there. It may be necessary to take temporary
  the computer on the network to do so.

  If you are the only user who has access to the shared drive, then you can perform a clean boot.

  Refer to this article for more information:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Steps to perform a clean boot:
  1. click on the ORB start on your desktop
  2. type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
  3. in the general tab, click Selective startup.
  4. under Selective startup, clear the check box load startup items.
  5. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
  6. click on OK.
  7. When prompted, click on restart.

  NOTE: Please check that you start the computer in normal mode after a repair. Follow step 7 article.

  If you do not have access to the shared drive, and then you mayneed ask that this action taken by the it Department, or a person who has access to
  the physical location of the shared drive.

  Kind regards
  Amal-Microsoft Support.
  Visit our Microsoft answers feedback Forum and let us know what you think.