SRM 4.1.2 install problem

Similar Questions

• Service starts and then stops during the SRM 5.1.1 install

  
  My configuration is:

  • 5.1 ESXi
  • vCenter 5.1 has running on a virtual machine
  • Execution of SQL 2008R2 sparer vCenter VM
  • Separate the VM for the execution of SRM
  • Above config is replicated to the site of DR
  • vCentres are not in Linked mode
  • SSO separate databases for each site

  When I installed SRM, it was wrong at the end and then gave the service could start message.  Finally, after clicking try again several times, the installation is complete.  However, the SRM service has stopped.

  The service can be started, but it stops immediately without errors in the logs of Windows.  The only hint of information that may be useful is in the SRM Setup log:

  VMware: Srm::Installation:Utility:LaunchApplication: INFORMATION: executable completed. Result code = 1

  VMware: Srm::Installation:VMUnregisterSrmService: ERROR: LaunchApplication() failed. Executable = D:\Program Files\VMware\VMware vCenter Site Recovery Manager\bin\vmware-dr.exe, parameters = u 'D:\Program VMware vCenter Site Recovery Manager\config\vmware-dr.xml', Code = 1

  VMware: Srm::Installation:Utility:LaunchApplication: INFORMATION: launch executable. Command line = 'D:\Program VMware vCenter Site Recovery Manager\bin\vmware-dr.exe' - r 'D:\Program VMware vCenter Site Recovery Manager\config\vmware-dr.xml.

  VMware: Srm::Installation:Utility:LaunchApplication: INFORMATION: waiting for the child process to complete

  VMware: Srm::Installation: 'anonymous namespace': ReadFileCompleted: INFORMATION: asynchronous callback status: 109

  VMware: Srm::Installation: 'anonymous namespace': ReadFileCompleted: INFORMATION: asynchronous callback status: 109

  VMware: Srm::Installation:Utility:LaunchApplication: INFORMATION: child process stdout:

  I tried to get the result code = 1 but without success.  Certain sections of the KB speak the DSN system, but it is 32 bit and the connection test is successful.

  I have the same problem in both the DC SRM and DR DC SRM Production.

  Any ideas gratefully received!

  Hello

  You must create the 64-bit DSN for the SRM 5.1.

  Michael.

• Portege 3440CT OS install problems

  Hello
  Just decided to dig my 3440 ct that has Windows 98se on it and reformat an update with XP. He has only 64 MB at the moment, but I thought that if all goes well, then I would switch to 192 MB and whack in a disk that is larger than the original drive 6 gb for the moment. I have the floppy a usb card pcmcia (a Toshiba one).

  When I try to install XP, it sees the Cd and begins starting the process, for example. loading devices. But whenever it gets to the last line says «the installation program starts now...» "it crashes with a blue screen with an error"0x0000007B"that I find something to do with the boot drive.

  Then I deleted the diving and installed XP properly on a desktop computer using an adapter, put it back in the laptop it starts very well until the first wime you see the XP logo and then crashes with the same error

  Then I tried a 60 GB drive, I had in my laptop main that I know works fine and got exactly the same message.

  I then tried Windows 2000 which had the same problems, but eventually worked with 98SE. I tried both with FAT and NTFS and I installed the latest version of bios 1.60. But in vain.

  Someone at - it good ideas as to what im doing wrong?

  Hello

  When you install the restore CD is a simple file and when the external drive is just plugged and recognized that it is not problem to install it but when you install the original version of Microsoft installation must be interrupted and the unit should restart for the installation continues. At the moment the external drive can not be found anymore. I assume that this is the problem in your case.

  Try to create two partitions and copy the CD Win on the second partition and try again to install the unit.

• Tecra 8000: xircom realport modem cem56G-100 lan install problem

  Hi, I have tecra8000 win98 on which I'm trying to install a xircom realport cardbus modem. I downloaded of updates (always available) on the site of intel as well as of the last update of the firmware to resolve installation problems. None of these helped to solve the problem that I encounter, for example, it seems that my xircom is not accepted (windows cannot install the adapter) and on reboot I get a message that the card does not work correctly. Also, I can not select the realport modem card from the adapter list because she isn't here. each index or tip is welcome thanks in advance
  Stephaan

  Hi Stephan,

  Is the latest version of the driver 2.70.01.00?

  Can you please check in the properties for your modem under device status if there is a message (for example Code XXX).

• Pavilion dv7-4010em windows 7 install problem

  Hello. I had a problem, I try to install win 7 64 on pavilion dv7-4010em laptop and not show me any disk at all, but if I try to install win 7 32 I did not have this problem.
  
  I need to know what driver to HARD drive I use, I try and say Windows is not good?
  
  Any idea?

  Thank you in advance.

  Now Im allmost, install the drivers a few complete and done
  
  I take YUMI http://www.pendrivelinux.com/yumi-multiboot-usb-creator/ and just make it bootable USB pendrive without pilot and other needs.  I'm on win 7 32 bit PC system
  
  all all with installation take 20 minutes.
  
  Thanks for the support in any case thumbUp

• Toshiba ECO utility install problem on NB550D

  Hello world

  I bought a netbook NB550D and upgraded with a stick of 4 GB of RAM and Windows 7 Ultimate x 64. The computer now runs really faster than with the initial Setup, but I have some problems with some software from Toshiba. The ATI graphics driver is installed and the package of added value. But:

  -I'm not able to install the Eco utility. I tried several versions (also dedicated to x 64 OS), but I have to every time the same question during the installation process: installation stops suddenly, and a warning message box appears, but does not have any text contain. After that, the alternation istall is cancelled. Does anyone experience the same problem?
  -J' have also installed the utility Flash Cards, but the bar does not appear when you press the Fn key (shortcut keys work in all cases).

  Would appreciate the help, or the delivery of the driver versions that are suitable for win 7 x 64.

  Thanks in advance!

  Thanks for your comments and share this news!

• Motorola Phone Tools install problem

  HP Vista 64-bit. Can I get an installer loaded, but it will not install the program completely. I had my XP and I think that the problem has to do with Vista. Is there some kind of patch or something to make it compatible? Thank you.

  What version of MPT do you have? I think you need V5.0 for Vista.

  http://direct.Motorola.com/hellomoto/nss/productresource.asp?PhoneModel=mpt

• Cannot install: problems connecting to the server

  I have a problem when installing the new version of Skype, whenever I have install and starts to say there is a problem to connect to the server, download Skype alternative, and when I do it here it again when I install, can someone help me with this problem of server?

  What Setup you're trying to open?

  The only what you have to do is copy the Skype.exe and Login.cab files and paste these files the installation of Skype folder or even any new folder on your computer.

  If you extracted all the files from the SkypeSetup_6.18.0.106.msi file, then you should be able to find the Skype.exe and Login.cab files in:

  \SourceDir\Program Files\Skype\Phone\

  

  

• HP Pavilion dm4-2165dx WiFi driver install problems

  Product:

  HP Pavilion dm4-2165dx

  OPERATING SYSTEM:

  Windows 7 Professional 64 bit VL

  Description of the problem:

  Impossible to install the WiFi driver. Tried all 3 drivers provided on the support site: Ralink, Realtek & Intel WiMAX. All 3 installers indicate either the WiFi card was not found / detected or the installation program just hangs.

  Changes to the system:

  A clean install of Windows 7 Professional 64 bit DVD VL - required to connect to our domain controller.

  Found a solution.

  (1) to restore the system to factory settings

  (2) save C:\SWSetup\Drivers file on a USB

  (3) install Windows 7 Pro 64-bit

  (4) copy C:\SWSetup\Drivers on HD

  (5) install device drivers

• Desktop HP Pavilion p6210y PC: RAM install problem

  My office is in the factory with the exception of the video card which is a NVIDIA Geforce GTX 750Ti graphics card.  I bought by 4 chips of RAM DDR2 PC2 6400U 800 MHZ 240 PIN by Samsung and installed according to the instructions from HP.  I also double checked my bios and updated to the latest version that has been on the HP website on 20/05/15.   When installed and rebooted my computer I first had a problem with my computer freezing completely on my and I have to make a difficult stop by disconnecting the tower.  I did a reboot and done a diagnosis (F9) and waited to see what would do the memory.  Initially, I had a 'FAIL' BIOMEM-1 error.  After a few attempts, I then is gone one chip at a time and done the same thing.  After that the first 3 installs successfully, I determined then a single chip was bad.  At this point, I restarted my system and started running it with 12g of RAM.  After about 10 minutes, my computer froze again and went to a blue screen stop.  After that restart the desired system get a dskchk is for windows.   I've looked online and made a Windows hotfix, and cured this problem but continued to get the gel and closed blue.  I then reinstalled the factory RAM chips, and it is not reappeared since.  According to all that I can see 3 of my chips are good and should run.  What other steps could be or are at - it a driver for updating bios them or not, I have to do?  Help, please!

  @sooperglew

  Only using three DIMMs will force the PC to run in single channel mode.

  Your first consideration should be Support HP or HP sales during the consideration of upgrades or replacement of memory. If you want to consider other manufacturers of the best way to avoid memory problems is to contact one of the leading manufacturers of memory. I would recommend that you try the tools of these manufacturers: Corsair, Kingston andCrucial. Once you have determined the DIMMs that you need, then contact commercial or technical support to check that you have selected the correct DIMMS. If you buy directly from manufacturers, then they will stand behind their products.

• T400 own install problem for the graphics card hybrid

  I did a clean install on the T400 and installed all the drivers that are essential under the SWTools folder, but I see a problem with the card ATI will not work correctly.

  After installation from the folder videos and restarted the laptop. There is a sign next to the 'ATI Mobility Radeon HD 3400 Series' in Device Manager

  Under device status, I see the following error message

  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  Has anyone seen this error? I tried to reinstall the driver again, but that does not solve the problem. Actually, the PowerManager now has trouble switching graphics, with the balloon message "system cannot activate graphics high-performance" close all 3D applications or video and disconnect the external screens. " Switch graphics processors. »

  Any suggestions on how to fix this?

  The model is 2764-CTO

  Just figured it out. This feature requires Vista SP1. Since my Vista disk is the original disc of RTM without SP1, this is why I came across this problem.

• Photosmart D100: Instalation problem

  Hello

  I have a windows 8 (64-bit). I got a Hp Photosmart series of D100 as a gift, so I went on the internet for how to install the necessary software.

  I downloaded the "HP Photosmart full feature and software drivers" and is run with the "HP download and install Assistant".  I clicked on "install" and another window open with 3 options (I will translate from french) install, Readme and quit smoking. I chose to install.

  Another open window called "Hp-photosmart D100 series" with a photo of two Asian, latina, a black one guy an old white man. A cd that runs on the left and a blue arrow point to "a check of the system".

  That is the problem. A window appears and says "the specified file is not localizable.

  The window closes after I press "ok" and the previous changes of windows and display the message "process shrink" and closes, so I'm new to the "HP download and install wizard".

  Thanks for any help, I've been on this during more than an hour and I'm really thinking about buying a new printer

  Hello there @fb_hp_user ,

  Welcome to the Forums! I hope you enjoy your experience

  I noticed your messages on the error 'the specified file not found' message you see when you try to install your printer on Windows 8.1. I'm going to share with you a few suggestions.

  1 make sure that the Internet Explorer pop-up blockers are turned off before downloading the installer

  Blocker Internet Explorer: How can I disable Blocker?

  • Try to install

  2. If you are using McAfee secure Live or any other firewall, please temporarily disable the "real-time scanning".

  How to disable real-time scanning

  • Try to install it

  3. go to the start screen (you can also press windows + R to open the Run dialog box) and type %windir% should display the windows folder.
  
  Click on the folder and scroll until you see the files. Search for a class named 'HPWINS *.» DAT"(le * est un nombre qui varie) remove this file and retry the installation."

  • Try to install it

  I hope that my post was helpful, thank you for posting!

  

• install problems in time real 8.6

  Hi all

  I m trying to install 8.6 in real-time on a target office. I have executed the audit tool, and it says that it s a consistent target.

  I created the key USB of PC desktop utility and formatted the target without any problem.

  When I rebooted the PC network adapter has been initialized with the following address: 169.254.81.194 and it doesn´t appear on MAX.

  He should have started with 0.0.0.0, so that we can then set the IP address.

  I'm doing something wrong?

  Thank you

  Adam

  Hi Adam!

  You said before that you had 2 network cards!

  Can take you a look at this page: http://digital.ni.com/public.nsf/allkb/FD9E1AF5AB1343098625736F0076DE6B?OpenDocument

  And then try to connect to your target using cross-over cable.

  Kind regards

• HP Pavilion ab216ng-15 l: driver install problem

  HelloW, I bought a HP Pavilion Notebook 15-ab216ng. Ive just installed win 7 and I wanted to install the drivers, but 3 are still problems: 71831: 71924; 73525

  My biggest problem with the mommnet is that I can't connect to the internet.

  I downloaded the drivers on another pc then installs the drivers with a usb key. all were installed but this 3.

  Help, please

  Hello @michael20099,

  Thanks for the quick response!

  If you have problems to install the drivers, you can try using the tool at the following site:

  Open the Windows Update troubleshooting tool

  I hope this helps.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution' , this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Kind regards!

• Zoo Tycoon 1, Instalation problems, it stops the installation around 36% completion.

  Hi, I have a Windows XP, I also have Zoo Tycoon 1 full Collection. However, I have a problem to install the game. All right until I get at the end of instalation 35%. Then it stops and says. Error reading file D.Data/Maps/crater zoo. I could really use some help for your help thanks.

  Hi youngjosh23,

  • You are able to successfully install the other applications and software?
  • You install this game from a cd?

  If you use a CD or DVD to install this game, I recommend copying the contents of the CD/DVD on the desktop and try again. It is possible that one of the files in the CD is damaged.
  You can also try to clean the disc with a soft cloth and try again.
   
  If the installation of the game is stored on a computer again one of the files is missing or damaged.
  If you have a CD/DVD of the game trying to install using them.
   
   
  You can also try the steps in the below thread if you use CD/DVD:
  http://social.answers.Microsoft.com/forums/en-us/vistagaming/thread/c65f2128-0738-4D21-8DF6-9ee57bbba27c

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.