SSD intel SRT speed up lack of button (caching)

Similar Questions

• Elite800G1 Intel SRT speed option missing

  I have Elite 800 G1 Mini PC with SATA 500 GB and 128 GB SSD Crucial M4

  I would like to enable Intel Smart Response Technology to use SSDS as a cache for the SATA drive.

  Model of RAID is enabled in the BIOS

  If I CTRL + I start to configure RAID volumes and then acceleration Options is disabled

  If I install app Intel(r) Rapid Storage Technology there is a button of performance but no acceleration button

  Operating system installed on the SATA drive, SSD shows drive as manage avaiable in the tab, but no possibility to use the SSD to cache frequently accessed blocks.

  Intel says doc WHAT SRT is supported in the Intel chipset http://ark.intel.com/products/75007/Intel-DH82Q87-PCH Q87

  The trick was to remove the partitions from the DSS)
  Assuming that the HARD drive is 1 in BIOS boot oder (disk 0), SSD drive is drive 1

  Diskpart.exe
  list disk
  Select disk 1
  clean
  Then the acceleration options appear in the Panel of the rapid storage technology.  'Advanced mode' is read cache (use only if you think that your SSD could be unreliable and fail).  'Maximum' mode is read and write cache.
  Setup is OS + apps installed on a large HARD drive. Add a SSD as cache for the HARD drive may be using 64 GB of SSD.  No swap file on the HARD drive and use the space for a large pagefile on SSD SSDS remaining.

  Then the cue point to see what a difference it is to your workload

• XPS15 (L521x). 840evo SSD running at speed SATA2, does NOT speed SATA3.

  I bought a L521x was fitted with a 512 MB SSD, which was a 830 SSD from Samsung manufactured for Dell as equipment of OEM for which software Wizard did not work (IE I never checked before HD speed).

  Recently, I upgraded the original SSD with the Samsung SSD 1 TB 840evo and I started to manage the new SSD with magician. Now the bad news discovered is that, although I was expecting a performance gain:

  (1) the Windows index on the HD has not changed: always 7.7;

  (2) Wizard reports the speed SATA2 instead of the expected to the SATA channel SATA3.

  I know that the intel HM77 chipset supports the SATA3 specification.

  The OS is Windows 7 Ultimate x 64. The boot is via the BIOS (not UEFI). The partition table is the MBR (not GPT). The system is updated with the latest version of the BIOS and latest drivers. Of course replace the HD, I used the original connectors provided by Dell with Notepad.

  What wrong with my setup? In other words: why the SSD running at speed instead of SATA3 SATA2?

  Thanks in advance.

  Antonio

  Reference Dell Germany replied:
  http://www.maxrev.de/was-haltet-IHR-vom-Dell-XPS-15-l521x-t286801, start, 120.htm

  I found information that A16 has developed because there are poblems to the disks that were connected through SATA3 and this is the reason why they wer strangled to SATA2.

  I asked my supervisor... no new version comes out. You can stay with the A14.

  A15 should be fine or any lower version should be fine. Download it from the Dell site. The software allows a drop in ratings.

• Taken SSD Intel SSD 540 s M.2 supported by the MacBook Pro 13 "retina end? 2013 (11,1)

  You have all the information if the new series of SSD INTEL 540 s 1 TB m2 will work with a MacBook Pro 13 "retina end? 2013 (11,1)

  Intel said it does not support NVMe. Should or would add just performance gain?

  I discovered by the research so far it is not supported. According to the information that I had any player should of NVMe or OS X will not accept or even boot from it.

  If someone have different information or the best life experience - I'd be happy to hear...

• How to make the SSD intel for the express purpose of starting applications on Vista

  Hello

  start the passage of the hhd to ssd?

  You have a problem. I installed an ssd intel in the express purpose of starting applications and vista X 64. I tried the drive cloning, but wouldn't start. I tried a new install and it was going to move files into that, won't boot from either by car, but win wonder what version of the win even he wants me to start from and restarts any computer to the same query form. The SSD is disabled in the bios to get the boot. Had to disable the RAID to use trim to ssd so function.

  What I want to do: start just from the ssd. The only things I want written on this disc are applications or the os updates/fixes. Want to earn for knows to go for hard drives for data, and make all other write here.

  Is this possible... or what I am doing wrong? BTW due to config sata raid or ide Diane to get started.

  w/thanks... Duke

  Hi ssdprob,

  I suggest you to install the SSD as a stand-alone drive and do a clean format installation.

  When installing, do not select the SSD. After completing the installation adds the old hard drive in the system.

  Note: If you have Sata or Raid enabled, so make sure you have the drivers available for the same thing. During the installation, you may need to install the drivers, otherwise choose IDE to proceed to the installation.

  IMPORTANT: before attempting an installation format for Windows Vista on the SSD, make sure you also have a good backup of all the information stored on your computer, because this process completely removes the previous installation and the data stored on the system.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forumand let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Is not start a new series of SSD Intel 520 180 GB replaced on ENVY Notebook (i7 3632QM) WINNING 8 m4

  I have a couple of this desire m4 I7 product: C2M81UA #ABA who have 1 TB blue WD scorpio Win 8 Preinstaled.

  It is up to date with the latest form of HP, Intel and Microsoft updates. Including fast storage to intel.

  Recovery operating system, applications and drivers DVD set has been created using HP recovery utility.

  After that, HD has been replaced with SSD Intel 520 Series 180 GB.

  Issue.

  SSD is not start after the installation of the OS was made using the HP installation DVD set.

  Remarks:

  The SSD is recognized, while holding, partitioned and Windows is correctly installed
  However it does not start it freezes after Hp logo without message when Win 8 should begin.
  Changing legacy BIOS boot and secureboot options results in error message appear "3F0 there is no boot device."
  even if a new fresh installation by using any combination of these options, the SSD is recognized and the tests went ok in the bios utility.

  Linking the SSD as external USB installation interrupted Windows can be seen.
  He tried with an another SSD, which is the same model with the same results.

  Compatibility was previously at the website of intel for this mobile chipset QM77 http://www.intel.com/content/www/us/en/chipsets/performance-chipsets/mobile-chipset-qm77.html

  and SSD http://www.intel.com/content/www/us/en/solid-state-drives/ssd-520-brief.html

  In my opinion, it may be an option of configuration of the bios, firmware or the driver, but after 3 weeks I'm out of ideas.

  Does anyone has an idea how to solve this problem?

  Thanks in advance

  Hello

  He finally works!, what I just did in the last hours is to reinstall from the recovery HP DVD media. But first I set old bios to activate OS, Secureboot to disable.

  Then it was installed, it worked well this time.

  When I did disabled legacy BIOS os and active secureboot.

  It runs as it wants!, it takes only 5 seconds to turn screen tile (I use fingerprint to log).

  Thank you all for your support!

• Clarity on a Dell XPS 8700 with 2 TB SATA + Intel® SRT 32 GB SSD Cache harddrive

  Hello

  I am buying a Dell XPS 8700 with a SATA hard drive with a 32 GB SSD cache. I want to know if the SSD is a separate physical disk SATA hard disk, it will be the M.SATA chip on the motherboard.

  Please it is confirmed; I can by adding a larger 256 GB internal SSD, with the o/s re installed on the SSD with HDD as storage of 2 TB.

  Best regards & Thanks Sean

  Hi Sean,.

  Yes, it's an mSATA SSD and scalable. You have the option to install the OS on a bigger mSATA SSD if you choose to do.

• SSD Intel DC P3700 NVMe and performance in ESXi 5.5.

  Hello

  I have 2 HP Proliant DL380 G9 with a 2 TB Intel P3700 NVMe SSD PCI - e card each.

  To put a virtual machine on these cards, I don't get the performance I expected.

  My basis for this is a Workstation Windows 8.1 with a 800 P3700 Go card for OS/workspace based on a Supermicro X10DAI motherboard.

  When I benchmark P3700 of this workstation, I get results and performance as expected.

  During the calibration of a virtual machine on a data P3700 store, I get waaay lower results, especially for workloads sequential.

  Change controller of paravirtualised, results changes a little, mainly best write performance, but the results are always a way weak.

  I use the following driver for P3700, downloaded from the vmware.com website:

  Is - 1.0e.0.30 - 1vmw.550.0.0.1391871.x86_64.vib

  Screenshots of P3700 on Windows desktop / VMWare workstation VM / ESXI 5.5:

  

  
  

  
  

  Paravirtualised:

  

  
  

  Any ideas?
  

  Now we are talking about, the drivers are definitely the big question here.

  Pre-release of Intel driver: intel-nvme - 1.0e.0.0 - 1OEM.550.0.0.1391871.x86_64.vib, did the trick.

  The results are always a little strange when it comes to performance and results in read/write / values are not yet 100% where I want them, but ATTO finally shows sequentially results above the limit of 600/800 MB I saw with vmwares pilot.

  Storage of the weak watch anvil utilities score both on driver LSI_SCSI and paravirtualised. I'm not shure why, but outcomes are improved in a way.

  I guess than the version driver gold, and maybe a combination with ESXi 6 improve it more.

  I consider a little more.

  Intels pre-release driver with LSI_SCSI controller:

  

• Mini-Player lack of buttons according to research/Up

  My iTunes Mini Player now missing the search button and the next button upward. Yesterday, I had them now, they aren't there. iTunes is fully updated. How can I get that back?

  Does not have a lot of control as a mini Player that I can't watch other songs, or watch next.

  Il0 - Mini Player was too small when you drag the corners. UH...

• Lack of buttons on the top window right in Thunderbird

  My problem has already been discussed here:

  https://support.Mozilla.org/da/questions/987606

  This thread has been archived, so I can't comment on that. I have the same problem as described here: every now and then, the three buttons on the right top of the page in the main Thunderbird window stop working. In fact, they are not yet drawn more. I suspect that this may be related to (UN) hibernation the machine because the problem started occurring at the same time I started using Hibernate in Windows 7. Alternatively the bug was reintroduced in a Thunderbird update occurring between one and two months.

  No other program of your use XUL as a window definition language is is my guess. You are using a non-standard theme? This happens in the VNC or only after the event?

• HP Envy H8-1423: HP Envy H8-1423 with ssd Intel 730

  
  

  Thanks for your reply.

  I tried another port but without success.

  I want to load Windows on it as the main drive for general use. The real HD Seagate is slow...

  One thing I have done is to partition the disk with window and that works, so I can see it with the file Explorer. The next step is to do with the Intel data migration tool, which is not the case at the moment...

  Gilbert

• Windows 7 - Start Menu power supply lack of button 'stop', 'sleep '.

  Hi all

  My power button on Start Menu is missing the 'Close' and 'Sleep' options.   Everything is displayed is 'Locked', 'Disconnect' and 'Switch user' (in gray).  I searched Internet solutions and tried * everything * recommended that in return, including:

  -right click on the power button and by changing properties

  -modification of the options in the application of power of Control Panel

  -change the registry setting to Start Menu

  -using the Group Editor to change the option to Start Menu power button

  -checked all of my system files to be ok

  I've been smart to do these things and always return the default settings later.

  Other observations:

  -the power button on the main Windows login screen * fact * have these options

  -When you use the Control Panel power approx., I even not give me the option to change the Start Menu power button

  I use Windows 7, 64 bit, professional on a Phenom II X 4 4 GB system.

  Help!  I'm a poster for the first time and I'm completely stumped.

  Thank you

  Minnesota Bob

  I solved the problem.  It turns out that there are two 2 group policy changes that had to be modernized.  Here's what to do (some steps copied from Microsoft article)

  Click Start, run.
  Type gpedit.msc , and then click OK.
  Navigate to the following location:
   
  Taskbar and User Configuration Administration\menu located
   
  Double click on "Remove and prevent access to the close command.
  Select 'off '.

  Double-click on "Start change power button Menu"

  Select "enabled."

  Choose "Shutdown".

  If you don't want to go through these steps, create a new user account will work as well.  Of course, then transfer all your settings of the old user account.

  Minnesota Bob

• Lack of button "clean up system files".

  I tried to run Disk Cleanup and clear up some space winsxs takes too much space, but I noticed that the button "Clean up system files" is missing. I use Windows 7 Ultimate

  A new feature has been added to cleaning disc in October 2013, which is not available in cCleaner. You must change the existing settings to take advantage of the new feature. Type Disk Cleanup in the search above the Start button box and press ENTER. Click OK and after the calculation of space, you will see a window with a list of files to delete. Use the right-hand scroll bar to see the entries hidden further down the list. Check the boxes in front of the backup of the Service Pack files and cleaning Windows Update and click OK if you don't see cleaning of Windows Update then click clean up system files . You can see savings every time after Windows has been updated, but they are not as important when it is run after the first time. You must restart the computer to complete the process.

• SAMSUNG SSD PM830 mSATA 32 GB about to fail in XPS one27 All in One how to replace disk SSD Intel RST?

  I have a XPS One27 all in a Win 7 Ultimate.

  RST is saying that my 32 GB SSD drive is about to fail and I must continue to reset, then it errors again.  What I have to use the RST for acceleration on the XPS one27 AIO or is there a way off course?  Or is it easy to replace?

  Thanks in advance for all advice - James - UK

  Hi James,

  I suggest that you run the diagnostics on the computer by following the steps mentioned in the video below and check if there is any problem with the hardware on your system.

  http://Dell.to/164l6g4

  Please let me know the results.

• Lack of button "sum in Mono...

  Hi all

  I opened a session where a track including stereo audio is just mono on the master... I can't find any button 'Sum to Mono' - strangely - on the track as usual, so I guess that something strange happened with this session... any help? I thank in advance.

  Is this a real session of stereo in the first place? And even if it is to have placed your stereo audio in a mono track by chance?