SSL VPN recommendation without encryption RC4

Hello

Actually I m using Annyconnect in ASA with SSL RC4 Cipher Suites taken care of, vulnerability it is recommended to use without RC4 encryption.

The question is, there is a document illustrating the best practices or recommendations to do?, I Don t know if it has an impact in this change, or if it is supported in the code.

Concerning

Ricardo

Ricardo,

Recommendations:

http://www.Cisco.com/Web/about/security/intelligence/nextgen_crypto.html#15

The impact is usually double that:

-All clients/browsers will support new encryption algorithms

-What level of computational overhead will be presented.

ASA side it is a cryptographic chip that is quite effective at handling in general crypto.

If your clients support address allowing DHE based ciphers.

I don't think there is a big best practices doc avilable, need a little more on the environment.

M.

Tags: Cisco Security

Similar Questions

  • agent of SSL VPN error without reason

    Hello

    Message error please refer to the attachment.

    If I'm right, this may be caused by the service of Sharing (ICS) Internet connection I used the network cable with my iPhone by creation-to-peer wireless network at the hotel and before that, she worked normally all the time.

    For the moment, I can also connect VPN successfully but the State always change to "reconnect" after 8 seconds and error message popup after that many try.

    I put the function ICS 'manual' or 'disabled' and make sure that it is not in running, but not useful.

    OS: Win7 Pro x 64 Sp1

    AnyConnect VPN Version client: 2.5.6005

    A response would be appreciated.

    Andy Xu

    There is error in the SSL protocol stack. try to reinstall the vpn client. It can work.

    I found the information for the error you get below.

    The VPN client agent SSL engine encountered an error. Please retry, or restart AnyConnect. 

    Description AnyConnect has encountered an unexpected and unrecoverable error in the SSL protocol stack. One possible cause is a flaw AnyConnect.

    Recommended user response restart the computer or the device, and then try to start a new VPN connection. If the problem persists, run DART (see DART helps collect troubleshooting information) and report the error to technical support for your organization and include the DART bundle.

    Recommended response administrator if the problem persists, open a case with the Assistance Center (TAC) Cisco technical and include the DART bundle.

    Here is the link

    http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect25/user/messages/AC25-VPN-user-msgs.html

  • SSL VPN without client

    Hi all

    I would like to know if, in confuring a SSL VPN mode without client, servers, I need to access must be directly connected to the VPN gateway?

    Thank you in advance.

    Servers can be anywhere in the network, but routing should be in place to reach VPN gateway.

    Thank you

    Ajay

  • Order SSL VPN with Cisco Cloud Web Security

    We have implemented Cisco Cloud Web Security with the connector of the ASA and transfer all traffic port 80 and 443 to the Tower of the CCW. We have enabled HTTPS inspection, and I was wondering if there was anything, we can add in the configuration that would allow us to control (allow/block) SSL VPN?

    #Clientless SSL VPN is not supported with Cloud Security Web; don't forget to exempt all SSL VPN traffic without client service ASA for Cloud Web Security Strategy.

    Reference: http://www.cisco.com/c/en/us/td/docs/security/asa/asa90/configuration/gu...

  • Clientless SSL VPN w / RDP

    I have a SSL VPN configuration without client for a user and try to use the rdp with a bookmark plugin.  I bookmarked configured for rdp: / / , but when the user clicks on it, a Web page opens with an inability to display a message and a url of type https://.plugins./rdp/index.

    HTML? target = rdp: / /? csco_lang = en.  If the user clicks on the button Terminal servers and then manually selects DPR: / / and between the IP address of the server it works fine.
    Any thoughts?

    ASA v8.0 (4)

    Hello

    It seems that you have enabled the option "smart tunnel" for the RDP bookmark. Plug-ins are not supported with smart tunnels and can cause the error you see.

    Could you please make sure that the smart tunnel option is disabled and let us know if you still see this problem?

    Thank you

    Steve.

  • SSL VPN without disabled in ASA5505 after the Activation of the AnyConnect client

    Hello everyone,

    I am facing a problem with the VPN service in ASA 5505. Initially, I was using SSL VPN without customer who was working absolutely fine, no problem. Recently I bought AnyConnect Essentials License with license AnyConnect VPN, Mobile (for focusing on the Client SSL VPN Service for desktop and mobile respectively) and have activated these keys inside of the firewall. After that I may be able to connect to based on the VPN Client, using the AnyConnect client. Clientless VPN access is not allowing you to connect and displays an error (see the attached screenshot).

    I created two VPN profiles Viz, basic (for clientless VPN) and rvsvpn (for client based VPN). Download the AnyConnect Client I can connect to the rvsvpn profile. But if I try to connect using the basic profile, it throws an error has been to what is displayed in the exhibition.

    Please help me in this regard, as what can be done to use both the vpn connection profile. Or what the use of AnyConnect disables client access?

    Waiting for your help.

    Thanks in advance.

    Samrat.

    "Anyconnect essentials" in your configuration command to disable all profiles without customer (as well as other features that require the Premium license).

    Essentials and Premium are mutually exclusive as the performance of duties. You can have both installed licenses, but only use one or the other (and never both at once) in your running configuration.

  • ASA 5510 - SSL VPN without CLIENT - remote desktop

    Is it possible to make a desktop connection remote clientless SSL VPN with a browser? I know that I can do with client anyconnect SSL but I can do without a customer?

    Yes it is possible, you must first make sure that you have transferred to the ASA RDP plugin. When you are editing you bookmarks, you will see an option for RDP.

  • New to SSL VPN, can I tunnel specific networks without specifying the list of applications with Smart tunnels?

    Hello

    I'm all new to SSL VPN, and I am a bit lost... I tried to get SSL VPN to go for our company and we have been asked to deploy a completely clientless solution that will provide access to our network based on subnets. Is this possible with the chip-tunnels? I tried a few different configurations and it doesn't seem to work. It works with ANYCONNECT but we have to go without a client. They feel that we can do without customer access to destination networks. Is this possible?

    Thank you in advance...

    That's what you can do with a solution without a client:

    1. Allow access to web resources (using the url list)
    2. Allow access to the application of TCP based (using java-port forwarding or smart tunnels)

    If you have to give access to all subnets, then you will need to go full tunnel effect which is Anyconnect SSL.

    HTH

  • AnyConnect and SSL - VPN without client

    Are there problems in running Cisco AnyConnect and SSL - VPN without client side by side?

    I am currently looking into adding features for an ASA AnyConnect who currently set up to operate without SSL - VPN client. The system without client is not removed. I don't know how to set it up, I wonder if someone has already set up this or if there is no problem with this Setup?

    Hi Daniel

    It's a little complicated if you want a granular authentication and authorization, but it works.

    I'm running an ASA with IPSec, SSL Client and clientless SSL.

    Each of these virtual private networks with user/one-time-password name and certificate based authentic.

    The main challenge is to put in place its own structure of profile cards, connection profiles, group policies and dynamic access policies.

    Feel free to ask questions...

    Stephan

  • Groups without SSL VPN client

    Greetings. I currently have an ASA5520 in place running 8.0 (2) IOS. We have configured a clientless SSL VPN portal that we currently use as a 'test '. We try to solve the question deals with the use of the SSL VPN connection page groups. Currently, the ASA is set to authenicate names of username/password to a Microsoft Windows 2003 using IAS (RADIUS) server. It works very well.

    What we want to do, is to "lock" the user account to a group alias in the VPN SSL ASA login page. For example, our SSL VPN connection page displays two options for 'Group', 'sales and 'tech'. In its current form, a sales user can select one of the displayed groups and always be authenicated. Anyway is to deny the login information if a user does not select the appropriate menu GROUP drop-down? It would certainly help to ensure that users choose the right GROUP in the menu dropdown.

    Any information would be greatly appreciated.

    Joe

    In order to put the user in the appropriate group, set the attribute RADIUS 25 as OU = ASAGroupPolicyName. then try the locking of group control to lock the users.

    http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/gh_72.html

  • Should what license I for 25 SSL VPN peers

    Hi all

    I want to implement cluster active / standby with a pair of ASAs 5550 and I have a licensing question. Here's the "sh - key retail activation" leave two output devices...

    ASA1:

    SH - activation in detail key:

    Serial number: XXXXX

    No temporary key assets.

    Activation key running: XXXXX XXXXX XXXXX XXXXX XXXXX

    The devices allowed for this platform:

    The maximum physical Interfaces: unlimited

    VLAN maximum: 250

    Internal hosts: unlimited

    Failover: Active/active

    VPN - A: enabled

    VPN-3DES-AES: enabled

    Security contexts: 2

    GTP/GPRS: disabled

    SSL VPN peers: 2

    Total of the VPN peers: 5000

    Sharing license: disabled

    AnyConnect for Mobile: disabled

    AnyConnect Cisco VPN phone: disabled

    AnyConnect Essentials: disabled

    Assessment of Advanced endpoint: disabled

    Proxy sessions for the UC phone: 2

    Total number of Sessions of Proxy UC: 2

    Botnet traffic filter: disabled

    This platform includes an ASA 5550 VPN Premium license.

    Flash activation key is the SAME as the key running.

    ASA2:

    SH - activation in detail key:

    Serial number: XXXXX

    No temporary key assets.

    Activation key running: XXXXX XXXXX XXXXX XXXXX XXXXX

    The devices allowed for this platform:

    The maximum physical Interfaces: unlimited

    VLAN maximum: 250

    Internal hosts: unlimited

    Failover: Active/active

    VPN - A: enabled

    VPN-3DES-AES: enabled

    Security contexts: 2

    GTP/GPRS: disabled

    VPN SSL counterparts: 25

    Total of the VPN peers: 5000

    Sharing license: disabled

    AnyConnect for Mobile: disabled

    AnyConnect Cisco VPN phone: disabled

    AnyConnect Essentials: disabled

    Assessment of Advanced endpoint: disabled

    Proxy sessions for the UC phone: 2

    Total number of Sessions of Proxy UC: 2

    Botnet traffic filter: disabled

    This platform includes an ASA 5550 VPN Premium license.

    Flash activation key is the SAME as the key running.

    --------------------------------------------------------------

    It seems so obvious that I have to upgrade the first ASA to support 25 SSL VPN peers in order to create the cluster HA, right?

    Now, I want to know do I need the license "ASA5505-SSL25-K9" or something else.

    Thank you very much in advance for any help!

    Ah OK I see - right then: upgading pole will allow the license to share.

    Re the version target, I would recommend going directly to 8.4 (4.1). I have it deployed on several sites without problem.

  • After Windows Update ActiveX RDP through SSL VPN KB2675157 stops working

    We have a Cisco ASA 5510 with Clientless SSL VPN portal. I just found out that after installing the latest Microsoft Updates, bookmarks RDP has stopped working. He continues to ask that I should install Cisco Portforwarder control and then returns to the home page. I changed all the security settings, tried to install control manually, but nothing works. Finally, I found that after you uninstall Internet Explorer 8 update KB2675157 it works again.

    Is this a known issue?

    I just tested it on Windows XP with IE 8, I don't know if the problem occurs in other platforms.

    Good afternoon

    The issue you are running into is not caused by KB2675157.  This behavior was deliberately introduced by KB

    2695962.

    As stated in:

    http://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/Cisco-SA-20120314-AsaClient

    The Cisco PSIRT asked Microsoft to set the global Kill Bit for the control of redirector Port Cisco ActiveX on March 14, 2012.    Microsoft pushed the bit kill for the vulnerable control in may, 2012 batch of patches Microsoft Tuesday (May 8, 2012).

    Clients must go to one of the recommendations listed or such later versions listed below.  The recommended versions include fixes for issues disclosed in Cisco Security Advisory: Cisco ASA 5500 series Adaptive Security Appliance Clientless VPN ActiveX control Remote Code execution vulnerability of as well as those identified in the notice to Client of ASA.

    Affected version First version fixed Recommended version
    Cisco ASA 7.0 Not vulnerable Migrate to 7.2 or later
    Cisco ASA 7.1 Vulnerable Vulnerable people; Migrate to 7.2 or later
    Cisco ASA 7.2 7.2 (5.6) 7.2 (5.7)
    Cisco ASA 8.0 8.0 (5.26) Migrate to 8.2 (5.26) or later version
    Cisco ASA 8.1 8.1 (2.53) Migrate to 8.2 (5.26) or later version
    Cisco ASA 8.2 8.2 (5.18) 8.2 (5.26)
    Cisco ASA 8.3 8.3 (2.28) Migrate to 8.4 (3.8) or later version
    Cisco ASA 8.4 8.4 (2.16) 8.4 (3.8)
    Cisco ASA 8.5 Not vulnerable 8.5 (1.7)
    Cisco ASA 8.6 8.6 (1.1) 8.6 (1.1)

    Once the affected control has been improved by starting a VPN session without client on an ASA that contains the fixed software, it will be used in all sessions.  This including those with ASA devices that cannot run the software updated.

    See you soon,.

    -Troy

  • Cannot access internal network so AnyConnect SSL VPN, ASA 9.1 (6)

    Hello Cisco community support,

    I have a lab which consists of two virtual environments connected to a 3750-G switch that is connected to a 2901 router which is connected to an ASA 5512 - X which is connected to my ISP gateway. I configured SSL VPN using AnyConnect and can establish a VPN to the ASA from the outside but once connected, I can't access internal network resources or access the internet. My information network and ASA configuration is listed below. Thank you for any assistance you can offer.

    ISP network gateway: 10.1.10.0/24

    ASA to the router network: 10.1.40.0/30

    Pool DHCP VPN: 10.1.30.0/24

    Network of the range: 10.1.20.0/24

    Development network: 10.1.10.0/24

    : Saved
    :
    : Serial number: FCH18477CPT
    : Material: ASA5512, 4096 MB RAM, CPU Clarkdale 2793 MHz, 1 CPU (2 cores)
    :
    ASA 6,0000 Version 1
    !
    hostname ctcndasa01
    activate bcn1WtX5vuf3YzS3 encrypted password
    names of
    cnd-vpn-dhcp-pool 10.1.30.1 mask - 255.255.255.0 IP local pool 10.1.30.200
    !
    interface GigabitEthernet0/0
    nameif inside
    security-level 100
    IP 10.1.40.1 255.255.255.252
    !
    interface GigabitEthernet0/1
    nameif outside
    security-level 0
    address IP X.X.X.237 255.255.255.248
    !
    interface GigabitEthernet0/2
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface GigabitEthernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface GigabitEthernet0/4
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface GigabitEthernet0/5
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    management only
    nameif management
    security-level 100
    IP 192.168.1.1 255.255.255.0
    !
    boot system Disk0: / asa916-1-smp - k8.bin
    boot system Disk0: / asa912-smp - k8.bin
    passive FTP mode
    permit same-security-traffic intra-interface
    network of the NETWORK_OBJ_10.1.30.0_24 object
    10.1.30.0 subnet 255.255.255.0
    network obj_any object
    network obj_10.1.40.0 object
    10.1.40.0 subnet 255.255.255.0
    network obj_10.1.30.0 object
    10.1.30.0 subnet 255.255.255.0
    outside_access_in list extended access permitted ip object NETWORK_OBJ_10.1.30.0_24 all
    FREE access-list extended ip 10.1.40.0 NAT allow 255.255.255.0 10.1.30.0 255.255.255.0
    access-list 101 extended allow any4 any4-answer icmp echo
    access-list standard split allow 10.1.40.0 255.255.255.0
    pager lines 24
    Enable logging
    asdm of logging of information
    Within 1500 MTU
    Outside 1500 MTU
    management of MTU 1500
    ICMP unreachable rate-limit 1 burst-size 1
    ICMP allow any inside
    ICMP allow all outside
    ASDM image disk0: / asdm - 743.bin
    don't allow no asdm history
    ARP timeout 14400
    no permit-nonconnected arp
    NAT (inside, outside) source obj_10.1.40.0 destination obj_10.1.40.0 static static obj_10.1.30.0 obj_10.1.30.0 non-proxy-arp-search to itinerary
    NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.1.30.0_24 NETWORK_OBJ_10.1.30.0_24 non-proxy-arp-search to itinerary
    Access-group outside_access_in in interface outside
    !
    Router eigrp 1
    Network 10.1.10.0 255.255.255.0
    Network 10.1.20.0 255.255.255.0
    Network 10.1.30.0 255.255.255.0
    Network 10.1.40.0 255.255.255.252
    !
    Route outside 0.0.0.0 0.0.0.0 10.1.10.1 1
    Timeout xlate 03:00
    Pat-xlate timeout 0:00:30
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    Floating conn timeout 0:00:00
    dynamic-access-policy-registration DfltAccessPolicy
    without activating the user identity
    identity of the user by default-domain LOCAL
    Enable http server
    http 192.168.1.0 255.255.255.0 management
    http 192.168.1.0 255.255.255.0 inside
    http X.X.X.238 255.255.255.255 outside
    No snmp server location
    No snmp Server contact
    Crypto ipsec pmtu aging infinite - the security association
    Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
    registration auto
    full domain name no
    name of the object CN = 10.1.30.254, CN = ctcndasa01
    ASDM_LAUNCHER key pair
    Configure CRL
    trustpool crypto ca policy
    string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
    certificate c902a155
    308201cd 30820136 a0030201 020204c 0d06092a 864886f7 0d 010105 9 02a 15530
    0500302b 31133011 06035504 03130 has 63 61736130 31311430 12060355 74636e64
    0403130 31302e31 2e33302e 32353430 1e170d31 35303731 32303530 3133315a b
    170d 3235 30373039 30353031 33315 has 30 2 b 311330 0403130a 11060355 6374636e
    64617361 30313114 30120603 55040313 0b31302e 312e3330 2e323534 30819f30
    0d06092a 864886f7 010101 05000381 8 d 0d 003081 89028181 00a47cfc 6b5f8b9e
    9b106ad6 857ec34c 01028f71 d35fb7b5 6a61ea33 569fefca 3791657f eeee91f2
    705ab2ea 09207c4f dfbbc18a 749b19ae d3ca8aa7 3370510b a5a96fd4 f9e06332
    4355 db1a4b88 475f96a1 318f7031 40668a4d afa44384 819d fa164c05 2e586ccc
    3ea59b78 5976f685 2abbdcf6 f3b448e5 30aa96a8 1ed4e178 0001300 020301 4 d d
    06092a 86 01010505 00038181 0093656f 639e138e 90b69e66 b50190fc 4886f70d
    42d9b4a8 11828da4 e0765d9c 52d84f8b 8e70747e e760de88 c43dc5eb 1808bd0f
    fd2230c1 53f68ea1 00f3e956 97eb313e 26cc49d7 25b927b5 43d8d3fa f212fcaf
    59eb8104 98e3a1d9 e05d3bcb 428cd7c6 61b530f5 fe193d15 ef8c7f08 37ad16f5
    d8966b50 917a88bb f4f30d82 6f8b58ba 61
    quit smoking
    Telnet timeout 5
    SSH stricthostkeycheck
    SSH timeout 5
    SSH group dh-Group1-sha1 key exchange
    Console timeout 0
    VPN-addr-assign local reuse / 360 time
    management of 192.168.1.2 - dhcpd address 192.168.1.254
    enable dhcpd management
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    Trust ASDM_Launcher_Access_TrustPoint_0 vpnlb-ip SSL-point
    SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
    WebVPN
    allow outside
    AnyConnect image disk0:/anyconnect-linux-3.1.09013-k9.pkg 4
    AnyConnect image disk0:/anyconnect-macosx-i386-3.1.09013-k9.pkg 5
    AnyConnect image disk0:/anyconnect-win-3.1.09013-k9.pkg 6
    AnyConnect enable
    tunnel-group-list activate
    internal GroupPolicy_cnd-vpn group policy
    GroupPolicy_cnd-vpn group policy attributes
    WINS server no
    value of server DNS 8.8.8.8
    client ssl-VPN-tunnel-Protocol
    by default no
    xxxx GCOh1bma8K1tKZHa username encrypted password
    type tunnel-group cnd - vpn remote access
    tunnel-group global cnd-vpn-attributes
    address-cnd-vpn-dhcp-pool
    strategy-group-by default GroupPolicy_cnd-vpn
    tunnel-group cnd - vpn webvpn-attributes
    activation of the alias group cnd - vpn
    !
    ICMP-class class-map
    match default-inspection-traffic
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map icmp_policy
    icmp category
    inspect the icmp
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the icmp
    !
    global service-policy global_policy
    service-policy icmp_policy outside interface
    context of prompt hostname
    no remote anonymous reporting call
    Cryptochecksum:261228832f3b57983bcc2b4ed5a8a9d0
    : end
    ASDM image disk0: / asdm - 743.bin
    don't allow no asdm history

    Can you confirm that this is correct, your diagram shows your IP address public on ASA as 30 while you have assinged on 'outside' interface like 29?

  • SSL VPN traffic

    Hello

    I have configured the client SSL VPN on SAA. I'm able to establish SSL VPN with the ASA and obtaining the IP address of subnet defined (CorporateVPN 172.16.0.100 - 172.16.0.110). But when I try to ping inside the property intellectual treats which is 172.16.0.1 and other machine in the range LAN getting loss of packets to the remote machine.

    What could be the problem?

    Below is the configuration of the SAA.

    ASA Version 7.2 (1)
    !
    Cisco - ASA host name
    test.com domain name
    activate the password password
    names of
    DNS-guard
    !
    interface Ethernet0/0
    Description connected to ISP
    nameif outside
    security-level 0
    IP address "public IP".

    !
    interface Ethernet0/1
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/2
    Description connected to the local network
    nameif inside
    security-level 100
    172.16.0.1 IP address 255.255.255.0
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    nameif management
    security-level 0
    IP 192.168.1.1 255.255.255.0
    management only
    !
    2KFQnbNIdI.2KYOU encrypted passwd
    boot system Disk0: / asa721 - k8.bin
    passive FTP mode
    clock timezone GMT 3 30
    management of the DNS domain-lookup service
    DNS server-group DefaultDNS
    Server name 203.123.165.75
    test.com domain name
    pager lines 24
    Enable logging
    asdm of logging of information
    Outside 1500 MTU
    Within 1500 MTU
    management of MTU 1500
    mask 172.16.0.100 - 172.16.0.110 255.255.255.0 IP local pool CorporateVPN
    IP verify reverse path to the outside interface
    IP verify reverse path inside interface
    no failover
    ASDM image disk0: / asdm521.bin
    don't allow no asdm history
    ARP timeout 14400
    Global 1 interface (outside)
    NAT (inside) 1 172.16.0.0 255.255.255.0
    Route outside 0.0.0.0 0.0.0.0 Gateway 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout, uauth 0:05:00 absolute
    internal GroupPolicy1 group strategy
    attributes of Group Policy GroupPolicy1
    Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
    WebVPN
    enable SVC
    SVC Dungeon-Installer installed
    time to generate a new key of SVC 30
    SVC generate a new method ssl key
    internal Netadmin group strategy
    Group Policy attributes Netadmin
    Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
    WebVPN
    Required SVC
    SVC Dungeon-Installer installed
    time to generate a new key of SVC 30
    generate a new key SVC new-tunnel method
    dpd-interval SVC 500 customer
    dpd-interval SVC 500 gateway
    username cisco password encrypted privilege 15 ffIRPGpDSOJh9YLq
    attributes username cisco
    VPN-group-policy Netadmin
    http server enable 444
    http 192.168.1.0 255.255.255.0 management
    http 0.0.0.0 0.0.0.0 outdoors
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    attributes global-tunnel-group DefaultWEBVPNGroup
    address pool CorporateVPN
    tunnel-group NetForceGroup type webvpn
    attributes global-tunnel-group NetForceGroup
    address (inside) CorporateVPN pool
    address pool CorporateVPN
    Group Policy - by default-Netadmin
    No vpn-addr-assign aaa
    No dhcp vpn-addr-assign
    Telnet 192.168.1.0 255.255.255.0 management
    Telnet timeout 10
    SSH timeout 5
    Console timeout 0
    management of 192.168.1.2 - dhcpd address 192.168.1.254
    enable dhcpd management
    !
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns migrated_dns_map_1
    parameters
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the migrated_dns_map_1 dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    !
    global service-policy global_policy
    WebVPN
    allow outside
    SVC disk0:/crypto_archive/sslclient-win-1.1.1.164 2 image
    enable SVC
    context of prompt hostname
    Cryptochecksum:13f5616c7345efb239d7996741ffa7b3
    : end

    Yes, 'inside access management' is only to manage/ping of the SAA within the interface. Without this command, they would still be able to access the internal network. This command is only used to manage the SAA within the interface itself.

  • Try to customize login page for ASA 5505 SSL - VPN

    Nice day

    I'm looking for help to customize the login page for the ssl - vpn as mentioned. When the vpn is configured, the default template allows my customers to connect with this: IMAGE 1

    While trying to change the login page, I have to create a new customization without CLIENT SSL VPN ACCESS-> PORTAL-> CUSTOMIZATION file in the ASDM. When I do this and I'm trying to change the login page, it comes up with 2 forms of authentication and a fast internal password like this: IMAGE 2

    How can I change the login page, I created so that users only see the fields username and password for regular as the default template?

    Thank you all for your time and assistance

    Joel

    Hi Joel,

    What you see is just the preview, right?

    Preview displays the purpose of customization, since the password internal and the second authentication controls are the features that are activated in different parts of the configuration.

    WebVPN

    allow outside

    internal-password enable

    !

    attributes global-tunnel-group DefaultWEBVPNGroup

    secondary-authentication-server-group second_authentication_server


    INFO: This command applies only to the SSL VPN - Clientless and AnyConnect.

    So I recommend to assign this object of customization to a group policy and test access to the content of the specific connection profile.

    Thank you.

    Portu.

    Please note all useful posts

Maybe you are looking for