Standard or cable modem Simulator to use?

Similar Questions

• How to use express airport when I have the cable modem? you want to listen to music in stereo.

  Hi all, this issue is driving me crazy. the goal was to use an Airport Express station to listen to the music of my devices in my stereo and a DAC to warm up the sound, but do not know how to connect because I have a cable modem my network on. I just want to use airport express to broadcast in stereo. I asked 3 people at the apple store today, and they seemed just as I asked them how to build a House from the ground. they had no idea. did someone hear doing this specific process? Thanks for any input.

  I understand the process of putting in place the DAC, is just the thing of the whole network that creates confusion. Sorry if this is the wrong place to post this.

  You can have one or the other hard connected (wired) network or a WiFi to your airport, but you can't have both. Unplug your ethernet cable from your Mac. Now, you'll be on a Wi - Fi on all devices. Reset your AE and use the installation wizard. Otherwise most suppliers of cable modems that with wi - fi for which they charge you an additional monthly cost.

• XP using a Dhcp Server if you have a cable modem. This is a Must?

  XP, network, Cable Modem. Do I have to use DHCP because I have nothing between me and the router? I watched hours of stuff on networks and nobody don't never went that far in anything. According to their patterns, Cisco or other, passed between their machine and the cable box. I've set up with static addresses (most of filmmakers disliked that sceme) and everything seems fine, but I have several others [don't know what to back]. To begin: Net bios on TCP/IP, WINSOCK, do I need? Well, I should have tried to find it, I should have written it down before I got here. Is it possible to save a project to the present, and I can drive around the site for a while? Now I get all these good advice from Youtube, and I bet everyone's probably laughing at me because you get ten different opinions to the same question. I have to add this. You can add memmory to your system for free! Yeh, you just go here and change this figure there, bam, more memory (long live Ram). It took a while, but for some, it may be a joke, but sometimes I can't tell when they're joking. Yes, I'll change a few settings. OOOPPPsss. Spybot, Ouch, he hacked me upward when I wasn't looking. DNS servers... Monitor drive..., the link layer,... .packet scheduler and now all of a sudden the TCPIP6 is suddenly. I've never seen a video on any of them, except 6, they were running 8.1. Cool. I hate just to bog down everything by adding all these other things if I don't. My settings seem to work very well, but sometimes things get a bit dodgy. Affecting those other things would make the program more stable, faster, or it's just the way it should be done? I hope all of you can remember when you have no idea, "what the hell do I need a Winsock for? I live in the desert.

  Hello

  Leave it as it is.

  DHCP
  http://www.bing.com/search?q=what+is+DHCP&QS=n&form=QBLH&PQ=what+is+DHCP&SC=8-12&SP=-1&SK=&GHC=1&CVID=1795ca6e2e5643be8bd65edf15171b31

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Can I connect printer to the usb port on the cable Modem CM100

  Hello

  This may seem like a stupid question, but here goes... I know that the usb port on my Linksys Cisco CM100 cable modem is an optional way to connect the modem to the computer. I wonder if I can use the usb port to connect my HP 1020 laser printer instead.

  The printer is not a network printer, and so I know that it may not work, but I have seen a few cases where a virtual port and install it as a local printer got to work.

  If I can connect the printer to the modem, and then he would give me a way to print from my laptop in the other room.  My printer is just beside my modem configuration and the router. I have a Linksys router WGR614 wireless who sees the devices on my network share, so I think he could see the printer connected to the modem (?)

  I couldn't find the answer to this anywhere. I didn't damage my equipment by blindly try this without knowing a little something. (I assume that the heart of my question is, on the CM100 usb port can be used for any usb device)?

  (I have Windows 7 64-bit operating system, in case you need to know).

  Thanks to anyone who can answer.

  djoseph

  A standard print server will allow you to connect a USB printer to your network. There are models wired and wireless depending on how you want to connect to the network.

• OfficeJet J6450 - printer connects wireless but does not print job cable modem replacement

  Material: My printer is an OfficeJet J6450. I am running Windows Vista, current update.

  Probably triggering the event: I replaced my modem docsis 3.0 with a doscis 2.0 modem. PSI has remained the same. All other software and firewall remained the same.

  Dysfunction: After the replacement of cable modem, I found that I could print is no longer in my HP OfficeJet 6450. I would get an error in the printer window ' error - print. "  After the reboot after the publication of the initial error, I would get the error "error - sent to the printer.

  What I did:

  As a first step, I've uninstalled and reinstalled the HP software for the printer (complete package with exception of PhotoSmart and HP customer monitoring program).

  Use the connection for the network printer wizard, I entered the router password wireless to the printer. At first I don't have a connection. Then I rebooted the computer and the printer. I also returned to the default setting of network on the printer and repeated the configuration of the network. The connection was finally successful.

  The automatic test of the network page and the network printer wizard confirms the connection. Digital display of the printer and the HP diagnostic utility has also confirmed the connection. But the diagnostic utility is unable to print a test page and throw an error - "Print Test failed.

  The result disappointing:  I still can't anything to print wireless.

  ... Thanks in advance for your suggestions to get my printer back on...

  Go to start > Control Panel > printers and delete all instances of the printer.

  Then re-add the printer:

  1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing.  Get IP address of a Test of Netowork wireless on the front of the printer (usually in the network menu).
  2. click on > start > Control Panel > printers.
  3. click on add a printer
  4. Select local printer
  5. Select create a new port and select Standard TCP/IP Port, and click Next.
  6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
  7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
  If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
  8. If prompted, use the driver that is currently installed.
  9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
  10. we may ask you to share the printer. Choose No.
  11. the printing area of Test Page is displayed. Go ahead and print it out.
  12. click on finish.

• How can I connect Windows Fax and Scan? I have a cable modem

  I have Windows 7 and I'm using Cablevision as my ISP. Installed a Motorola Surfboard Cable Modem SBV5120. I want to use the program Windows Fax and scan to send a fax, but Setup search a modem and can't find what I have Cablevision. How can I use the Windows Fax?

  Fax requires the use of a standard phone line, no cable.

• How can I connect a cisco router to the internet via a cable modem / router gateway

  I have searched here but can't find the exact answer that I'm looking. I have a switch and a router cisco 1760 2950. The router has an added ethernet wic card so I have two ethernet connections available. I would like to connect the cable modem gateway the router through one of the connections on the router, then the switch ethernet. I can't get this configuration to work. There are several different ways, I saw displayed to accomlish. DHCP, without dhcp, creating a separate network and giving the e0/0 cable an ip address in the range of addresses network gateways. None of this has worked. Can someone after the commands that must be entered on the router to make this possible?

  Hello, I'm assuming that your ISP is to give addresses via DHCP...

  And I suppose also we want to implement our router DHCP in our local network to give our PCs and laptops etc...

  So what we need to do is:

  conf t

  !

  interface e0/0

  Description # INTERNET #.

  IP access-group MY_WAN in

  DHCP IP address

  NAT outside IP

  No tap

  !

  interface e0/1

  # MY LAN description #.

  IP 192.168.1.1 255.255.255.0

  IP nat inside

  !

  IP access-list standard MY_LAN

  permit 192.168.1.0 0.0.0.255

  !

  MY_WAN extended IP access list

  allow tcp any a Workbench

  refuse TCP a whole

  allow an ip

  !

  IP nat inside source list MY_LAN interface e0/0 overload

  !

  IP dhcp excluded-address 192.168.1.0 192.168.1.99

  !

  dhcp MY_LAN IP pool

  network 192.168.1.0 255.255.255.0

  default router 192.168.1.1

  Server DNS 8.8.4.4 8.8.8.8

  In this configuration, I applied an ACL for a protection to my router and my network to allow only established connections that Ive from my LAN to return to me. Anyone who tries to open a connection to your router will be refused. Everything is allowed. But you can change this option to be more specific rather than wide.

  On your switch, if you leave all ports in the vlan 1 and have as access ports, it should work.

  Hope this helps

  Please note the useful messages and don't forget to mark resolved all questions answers. Thank you.

• cable modem-wireless combination or not?

  Hi, I'm going to switch from DSL to cable T - W (the only option in my building). I have an Airport Extreme on my TimeCapsule (it is the 500 GB disk version), that I use with my laptop. The iMac is connected to the router. I looked around at best buy where they sell T - W "approved" networking gear. Modems cable, all seem to be modem + units of combination of WiFi router at various points in price between about $80-200. My question is this: that any type of material that I use as long it's T - W compatible/approved. Any thoughts on the units of combination or is a cable modem + my Airport Extreme way to go. Not sure of the speed yet, but it is unlikely that I will contract for what that either more than 50 Mbit/s and perhaps even to 15 Mbps. Support some of the Motorola units that I was looking for very high flow rates, but they use the channel binding to achieve this goal. I read somewhere that if you buy the combined devices, you cannot update the firmware, but that doesn't make sense to me.

  Ask TW a modem without router built-in. And then run an Ethernet cable from the Ethernet port of the modem on the WAN on your AEBS port. You can connect your computer to the router either wired or wireless. It is the best configuration.

  If you do not need for Ethernet, then you can use a modem cable with router Wi - Fi as well. The main disadvantage is the difficulty you might have try to expand the modem/router using Apple hardware.

• Connect the Airport Extreme via Powerlink to the cable Modem

  I have problems with wifi at home as the location where the my cable modem is far from ideal. I currently connected to an Airport Extreme, which works like the router (the cable modem has the router function disabled). Attached to the AE is also a powerlink and I have an Airport Express connected to the powerlink, which has its own network.

  I was wondering if it would make sense to connect the powerlink directly to the cable modem and then put my Airport Extreme, a more central location in my home connected via Powerlink and there accumulate this way, rather than the current configuration.

  I'm getting a second Airport Extreme soon as well and I have several express in my house, but the problem is that my wifi is not fast at all.

  Powerlink adapters are Devolo 600 & 1200.

  Thank you

  I was wondering if it would make sense to connect the powerlink directly to the cable modem and then put my Airport Extreme, a more central location in my home connected via Powerlink and there accumulate this way, rather than the current configuration.

  It's always a good idea to place the 'main' AirPort router as close as possible of the area where most of the wireless devices should be used in this sense, your idea is a good thing... and in theory at least. ... .the powerline adapters allow you to do.

  However, in practice... you won't really know how well... or even if... this type of installation will work until you try you. The reason for this is there is so many different things that can affect the performance of a type of current line of the installation program.

  If you have time, there is certainly no harm in trying this type of configuration.  Post your results if you decide to try it.

• Network: 2 routers Apple broadcasting separate wireless networks; one (Xfinity/Comcast) cable modem

  Hello community!  Need help, I want to use two routers to establish two separate wireless networks on a cable modem connection.  I searched for my answer and see some other threads on this topic, but all are either a bit too technical for me, are incomplete on the answers to my questions - and all seem to be locked.  I have also searched YouTube and only see videos to extend a network with two routers - not my goal.  So here is a long, but a detailed post on what I need someone help with - thank you very much in advance if anyone can all small-not me-I hope it will be useful to others in the future.

  The program installation/hardware: I have internet Comcast/Xfinity that runs to a Motorola surfboard cable modem (SB6141).  I also have two routers apple - a Time Capsule from Apple AirPort (to end 2013) and a new (2016) AirPort Extreme.

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  My plan is to have the cable modem Surfboard connect to airport Time Capsule, which will then connect to AirPort Extreme (even if it could be reverse - no difference, except that the data that I show below comes from the time Capsule, which is currently connected to the modem cable).

  To read the previous discussions, it seems that the starting point would be: modem router #1 Ethernet WAN, then a router cable #1 LAN Ethernet to the Router #2.

  First issue of clarification - the connecting cable should go to the Ethernet WAN port on the Router #2 or a LAN Ethernet port?

  Now that the first easy question is the road, I need help to configure two routers connected to allow two separate networks.  A lot of discussions about the positions of static IP addresses, cascade, etc..  I need specific help with AirPort Utility on what to change on what router.  It seems obvious that the settings under the 'Internet' and 'Network' tabs are those who need to set - the 'wireless' tabs simply treats the name of the wireless network and settings - these, at least I can understand!

  I'll organise this tabbed - here go us.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Next up, the 'Network' tab utility AirPort/window.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  If I click on the 'Network Options' button at the bottom of the window, it takes me to the "Networking Options" window Here I have areas of entry to specify the DHCP lease duration, can specify the DHCP IPv4 range, as well as part of the extended DHCP IPv4 comments.  There are checkboxes: enable NAT Port Mapping Protocol. Select the host by default (with input if selected text box); Enable the IGMP Snooping; Block incoming IPv6 connections; Allow the Teredo Tunnels; and allow inbound IPSec authentication.

  For this window, here is the current settings on the Router #1:

  DHCP lease is 1 day; Beach DHCP IPv6 is 10.1.2 to 200; Hosts IPv4 DHCP Range is 172.16.42.2 to 200.  The following check boxes are enabled/checked: enable NAT Port Mapping Protocol. Block incoming IPv6 connections; And allow inbound IPSec authentication.

  Who can help me? What parameters, if all do I need to change the #1 router?  How to set up router #2 to make a second wireless network?

  Purpose: This is what I need--I need two separate wireless networks.  Before going further, by using the guest account and 5 GHz of a single router isn't an option for me.  I need to have both wireless networks separate (one of each router), do not talk to each other, or allow access between the two - the only is that they share the Comcast internet gateway.

  What you really need is a combination router / Ethernet switches that s supports VLANdedicated. Given that Apple routers do not, at best, you can potentially get the results that you are looking for, but at a performance cost. In other words, you can have two separate WiFi networks where clients connected to a network can not 'see' those related to another and both routers will always provide access to the Internet through Comcast modem. Note: Arris / Motorola SB6141 isn't a gateway device. Instead, it's a simple modem. A gateway is a router modem combination.

  To do this, should do the following:

  • The Time Capsule (TC) would need to be directly connected to the modem using an Ethernet cable. This base station would remain in its default configuration of the router. In other words, the router Mode (in AirPort Utility) would establish: DHCP and NAT.
  • AirPort Extreme would be directly linked to TB by Ethernet. The cable must be connected to one of the LAN ports on the TC on the WAN port to the extreme. It must also be configured as a router. However, there are differences in the extreme:
    • Use a different name to the Wi - Fi network.
    • Use another range of IP DHCP address. By default, Apple base stations use IP addresses in the 10.0.x.x range. I suggest that you set the base station of the second on 192.168.x.x range.

  There is a major drawback with this configuration. The second base station will be in a State of "Double NAT". Although this "separating" the two networks on different subnets, this condition is not very effective and connected to this network of customers will get lower throughput performance. There is no way around it and it is not recommended.

  First of all, the "Internet" tab/window Airport utility. Here are the options:

  Connect using: Router #1 has currently DHCP (which I think is OK?) What should it be set to Router #2?

  The two should be: DHCP.

  This tab lists also the current address in IPv4, the (255.255.254.0) subnet mask and the router address.

  These leave it as what. The TC is information of IP address of the modem. The extreme, he'll get the TC.

  It has grayed out information in the boxes for the DNS servers; Name of domain and DNS IPv6 servers.  At the bottom of the window, there is an IPv6 Internet WAN address listed.

  These leave it as what.

  If I click on the "Internet Options" button at the bottom of the window, it takes me to the 'Internet Options' window. Here, there are various IPv6 information - it seems that I can choose the configuration of IPv6 and the IPv6 mode using the drop down boxes/selections were also chosen.  There is also a checkbox 'Enable IPv6 connection sharing'. Are the current settings for these for Router #1: configure IPv6: automatically; IPv6 mode: Native; and check/yes to enable sharing of IPv6.

  Unless your ISP provides your IPv6 service, change the IPv6 configuration option to: 'Link-local only' on two base stations.

  Here, there is a drop-down menu "Router Mode", a DHCP range listed, and the ability to add or remove reservations DHCP and Port settings.  The DHCP range listed for Router #1 is 10.0.1.2 to 10.0.1.200.  There is currently no reserves DHCP or specified Port settings.  Finally, there is a checkbox to the bottom to "Activate the access control" - it is not currently checked/enabled.

  Router mode should be: DHCP and NAT to two base stations. Ignore the DHCP reservations and Port settings for now. Let the current DHCP range for the TC. Change the DHCP range for extreme for: 192.168.1.2 a.200. At this point do not access control for each base station.

  Since you seem to need the step by step instructions or need help to understand the different terms networking, I highly recommend that you help you to become familiar with networking, specifically on Apple systems. I suggest you consider taking the e-Book to the next control: take control of your Wi - Fi Applehttps://www.takecontrolbooks.com/apple-wifi network

• Time Capsule do not pick up address DHCP and cable modem...

  You just bought a Time Capsule and a couple of Airport Express. If none of these devices are connected together via Ethernet, they seem to have set themselves up, and all is well.

  That being said, I tried to create a mobile network instead of pure wi - fi and am studying various behaviors that are not as expected when I rear hub to the Internet Time Capsule, but need to isolate and go 1 bit at a time... (it works not as well as suggest Apple instructions on homelessness of installation)...

  If:

  1. configuration of the modem cable shows that DHCP is 'ON' and supplied address range 192.168.0.x by 192.168.0.y,.

  2 Cable modem wireless is disabled,

  3 Time Capsule Wan is connected to the cable modem, Ethernet

  4 Time Capsule is configured to request its address IP, DHCP

  5. Airport Express is in Bridge mode and have addresses such as 10.x.y.z (appears to be from a Time capsule).

  6. safe as Time Capsule is set to be as DHCP and NAT

  7. There is NO other device in this configuration connected by Ethernet except the cable Modem and the Time Capsule.

  So, why is the IP address of the time Capsule 76.181.45.xyz? (The address is NOT in the range of the DHCP as described in the #1; it is not supposed to be?) ....

  Whence this address?

  A friend says this address puts the "other side" Time Capsule of the cable Modem, directly on the Net?... (Shouldn't worry?) ....

  If none of these devices are connected together via Ethernet, they seem to have set themselves up, and all is well.

  It's because you didn't have the devices connected via Ethernet before you set up the. Given that the installation utility saw a wireless connection, it is assumed that this was the way that you want to connect devices on your network at all times... so he put it this way.

  If you had an established connection Ethernet before you ran the installer, then the utility would have detected this connection and set up the airport to "expand using Ethernet", does not extend to assistance of wireless.

  (it works not as well as suggest Apple instructions on homelessness of installation)...

  If all goes well, you don't talk about this document... Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo... .. Since the 'how' information in this article is at least 4 years late, bear little resemblance to the latest version of AirPort Utility and some of the information are simply not true.  This document if trash is what you... He'll probably do more harm than good with regard to the details of setting.  The article is OK for basic general information, however.

  6. safe as Time Capsule is set to be as DHCP and NAT

  It should not be if your modem is a modem/router "" or type 'bridge' of the device which is also DHCP and NAT services. The fact that you have disabled the wireless on the device confirms that it is both a modem AND a router. That being the case, then you have two devices that both struggling among themselves to try to control the same network... AND do you also have a network error called Double NAT... something you don't want.

  Probably the best at everything again and provide us with the number of brand and model of your "modem", that we can confirm what it is that you have, then the correctly configured time Capsule to work with this device. Once the time Capsule is set up correctly, it will be easy to put in place the other airports.

• How can I configure my Airport Express to mesh with new cable modem bridge mode?

  Time Warner sent me a new cable modem and my Airport express still flashing orange light. How can I configure the Airport express in bridge mode?

  You can simply do using AirPort Utility on your iMac or iPhone, as follows:

  • Run the AirPort Utility.
  • Select the AirPort Express Terminal and then, select change.
  • For a Mac:
    • On the network tab, change the router Mode to: Off (bridge Mode)
    • Select to update and allow the base station restart.
  • For an iOS device:
    • Select Advanced > DHCP and NAT
    • Change the router Mode to: Off (bridge Mode)
    • Select done and allow the base station restart.

  

• NETGEAR N300 Wi - Fi DOCSIS 3.0 Cable Modem Router (C3000) sees the backup HD Seagate but don't transfer

  V1.01.11 firmware, OS is Windows 10

  I bought the cable Modem Wifi Netgear N300. Except for the external hard drive Seagate (backup Seagate more 5 TB desktop external hard drive with 200 GB of Cloud Storage & Mobile Device backup USB 3.0 (STDT5000100)), all my devices connect to it without problem. However:

  1.) when I have the hood upwards the Seagate external hard drive, the genius of Netgear he sees, but says that the drive has 0 bytes available.

  (2.) that's why I can't back up by using the backup program WIndows 10 but

  (3.) I can "manually" drag files from my PC to the Seagate HD (the PC is connected to the modem router cable via wifi.)

  4.) when I connect the Seagate HD with a USB cable to the computer, the backup works.

  It's frustrating because I want to use the Seagate HD as a backup for some of my devices and I want the devices to send their data or the Netgear router.

  Can someone help me? It seems important that Netgear genius sees the HD Seagate but think it has no place.

  Richard

  I answer my own question (!) but is the answer that the HD 5 t is not compatible with the cable modem Netgear router? See:

  http://KB.NETGEAR.com/app/answers/detail/A_ID/18985

  Richard T.

• Cable modem of CM600 default after large downloads

  Hi-

  I use a CM600 modem with a router WNDR-3700v4.

  Recently, the cable modem has started to behave very strangely after the download of large files (1 GB or more seem to be the trigger point). Once the download is complete, I started experiencing excessive latency and packet loss to external sites. Ping times jump around 20ms for 3000ms and package loss ranges from 0% to more than 50%. Restart the modem cable does not resolve the issue until I download another file of large size. Interestingly, I found that if I disconnect the cable modem LAN cable when it is defective, the modem still shows an activity and a LAN link on it. I expect the activity ceases when he is physically disconnected and link drop. I swapped the ethernet cable and it made no difference.

  If anyone of you thin people have ideas?

  Thank you very much!

  The modem has been replaced and the problem disappeared. Yay guaranteed.

• HP Officejet Pro 8600 more N91: Printer crashes with 0xB845D7DC when connect to UPC Ubee cable modem/router EVW3226

  Printing: HP Officejet Pro 8600 more e-All-in-One Printer - N911g

  SN: [personal information]

  REF: CM750A

  FW: CKP5CN1516AR

  Then try to connect to the router wireless (active DHCP), the printer LCD display starts to blink and a second, it displays B845D7DC.

  After that, the printer asks to reset and it restarts with wireless off.

  I have a cable modem with router wireless of my cable TV UPC provider called UPC Ubee EVW3226.

  I tried to connect the printer to the router using the WPS button and provide the password. In both cases, I have the same behavior.

  I have a dozen other wireless home devices that connect without problem to the router. But not the printer.

  Please let me know what other information will be good for you to solve the problem. Or, please provide a workaround solution.

  I found the solution:

  connect to your printer cable (you can use a direct eth between your computer and your printer cable), access the web interface and disable support IPv6 (let the IPv4 only verified): network > General > protocols > only IPv4 verified. Save and restart the printer.

  In 80% of cases, it will work on the wireless connection. For the other 20% when it does not work, try to assign a static IP address to your printer (network > Wireless > IPv4) in a second time. Take data from your router (IP, gateway, DNS).