StepInto does not work in the user interface

Similar Questions

• ASDM does not work in the external interface

  Hello

  I'm new to ASA. I have ASA 5510 and strives to enable ASDM access through the external interface. but is not working for me... not. I set up a public ip address on the external interface and activated the ssh and asdm. SSH works but asdm does not work. This is a test environment, so I have not yet set up an ACL.

  VPN-TEST # show version

  Cisco Adaptive Security Appliance Version 8.2 software (1)

  Version 6.2 Device Manager (1)

  Updated Wednesday, 5 May 09 22:45 by manufacturers

  System image file is "disk0: / asa821 - k8.bin.

  The configuration file to the startup was "startup-config '.

  VPN TEST up to 4 hours and 33 minutes

  Material: ASA5510, 1024 MB RAM, Pentium 4 Celeron 1600 MHz processor

  Internal ATA Compact Flash, 256 MB

  BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)

  Start firmware: CN1000-MC-BOOT - 2.00

  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03

  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.04

  0: Ext: Ethernet0/0: the address is d0d0.fd1d.8758, irq 9

  1: Ext: Ethernet0/1: the address is d0d0.fd1d.8759, irq 9

  2: Ext: Ethernet0/2: the address is d0d0.fd1d.875a, irq 9

  3: Ext: Ethernet0/3: the address is d0d0.fd1d.875b, irq 9

  4: Ext: Management0/0: the address is d0d0.fd1d.8757, irq 11

  5: Int: not used: irq 11

  6: Int: not used: irq 5

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 50

  Internal hosts: unlimited

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  VPN-TEST # http see race

  Enable http server

  http 0.0.0.0 0.0.0.0 outdoors

  VPN-TEST # display running asdm

  ASDM image disk0: / asdm - 621.bin

  enable ASDM history

  Could someone please help me know what Miss me?

  Kind regards

  Praveen

  That's it, please add any combination of encryption by using the command "ssl encryption" algorithms, please add them in one line next to each other, and you can use '? ' to check available combinations.

  Kind regards

  Mohammad

• Default dashboard does not work after the user login

  Hi all

  We have one issue in 11.1.1.7.1 where CHEMINPORTAIL does not work for users. Thus, the user lands on the home page / recent rather than the default dashboard after login.

  I followed Doc-ID 1576576.1 and Bug 17071629 - CHEMINPORTAIL SESSION VARIABLE IS INEFFICIENT is reported. I applied patch 17071629 on top of 7.1. I tried and checked that

  • ·     The URL we use to login is "http://machinename:9704/analytics/saw.dll?bieehome & startPage = 1".
  • ·         There is no set start page in my account to user other than default.
  • ·         In the responses, the session CHEMINPORTAIL variable retrieves the correct path of dashboard.
  • ·         I removed the space in the name of the dashboard and tried with the following path ' / shared/table of edge/_portal/PortalPathTest. In addition, assigned the same default value in the session variable. I also tried "/ Shared Folders/table of edge/edge/PortalPathTest ' and '% 2fshared % 2fDashboard % 2f_portal % 2fPortalPathTest' but nothing works.
  • ·         lsinventory watch the patch has been applied successfully.

  One thing to notice-

  1. connection url is: "http://machinename:9704/analytics/saw.dll?bieehome& page = 1"

  2 after the connection URL in the browser is changed into "http://http://scoreboard-sit.wellsfargo.com:9704/analytics/saw.dll?bieehomemachinename:9704/analytics/saw.dll?bieehome" and displays the homepage instead of default dashboard.

  3. now at this point, if I add "& startPage = 1" to the URL from step 2 above in the browser, it navigates automatically to the correct dashboard by default.

  In addition, this fix has fixed dashboard by default in acting. This means that if I act as a user, I have ask on correct dashboard by default. But if the same user actually connects, it lands on the home page.

  I suspect that if the URL redirect after login is the real problem. Please suggest if someone has an idea.

  Thank you

  Séverine

  I think it was the question-

  There was an error in java script associated with an undefined object, "mode" in logon.js.  This is related to the access or Section 508 (checked by developer tools for IE).  We have deleted this code from the logon page that was causing the error. We had personalized the page quite a bit ago. When I ignore the error and not through, I go to the correct page of portal access road. So, let's replace the file logon.js with backup and I hope that it will solve the problem.

  See you soon!

  Séverine

• Model test using the interface user does not appear in the user interface

  I created a user interface for a model and trying to test it (using the model to test > start a new configuration > model UI (select user interface) > finish), it does not have the user interface, instead, it shows the summary of Configuration page. I checked the user interface, and there the correctly defined page flow. What is the reason for this and what is the solution. Thanks in advance.

  Check if you have associated page flow to the UI or not. Can be done in the edit page of the user interface.
  Check if you have added a page active in pageflow or not.
  Also make sure that you have visible page - page display of page condition is true.

• createTextField() will not work with the user interface component

  I use ActionScript to create a TextField and it works very well.
  
  If I then add (button or checkbox) user interface component to the stage of the textfield stops displaying.
  
  If I remove just the button on the stage of the object TextField does not always display. If I then remove the button component symbol in my library, TextField appear again!
  
  Here's the script. It works as long as there is no UI component in the library.
  
  See Code attached. Displays text, it will stop the display if you put a button on the stage.
  
  
  Thanks for any help
  
  MRC06460CT
  

  Hello

  I thought I had fixed this problem, but you are right. If I put the arguments in the correct order, the text does not go far.

  Thank you very much

  Mike Cohen

• Password does not work; Error "the user name or password is incorrect"

  This morning, I put the password to my PC windows 7 for the first time. I do not know what happpenede, but when I immediately rebooted my PC and I tried to get my password is not working, I get an error like: "" the user name or password is incorrect."" I press ok, and then when I try to reset the password, it appears: "this feature requires removable media, such as a floppy disk or USB flash drive. Please insert a disk or connect a USB flash drive, and then try again"I'm afraid, what past? I don't want to lose all my valuable files... . How to fix? I can't in my computer... Please help me! :(((

  Original title: Please, I need urgent help!

  Thanks for your advice, I did by myself anyway... I enter the menu of repair with F10. I'm strong enough to solve any problems: D have a nice day!

• Receiver DVB - T USB does not work with the user logon

  Hello

  We just bought the Toshiba USB DVB - T Tuner and it works fine as long as a user with admin rights is loged on. Using the device with user rights normal to display an error message that the device cannot be found.
  For reasons of safety only admins have admin rights so is it possible without causing a security problem solve this problem.

  Christian

  Seems that the driver/software that controls the Toshiba USB DVB - T Tuner don t run due to rights bad system.

  In your case, I would ask you sysadmin help

  It must assign the correct rights to your user account to ensure that the operating system recognizes and properly install the DVB - T USB Tuner.

  Hey Buddy

• session per user = 1 does not work in the database?

  Dear all,
  
  A profile has been configured on the database with the parameter session_per_user = 1 , but it does not work on the database.
  
  the user can make n number of sessions to the database. What could be the reason profile does not work?
  Please sugeest solution...
  
  Kind regards
  Rajesh
  
  Published by: Rajesh.Rathod on March 17, 2009 03:34

  You must change resource_limit true
  Search for details of text fo in metalink Note 745752.1

• Synaptics touchpad two fingers scrolling does not work in the player to develop modern UI application Windows 8.1

  I have a HP Envy TouchSmart UltraBook 4-1161er. Two fingers to scroll worked well in all modern user interface applications that come with the pre-installed operating system Windows 8.1, but the situation changed after the upgrade to Windows 8.1. Now this excellent and very useful two fingers scrolling does not work in the updated reader application. How to make it work?

  If the problem is in the drivers, maybe, install the drivers the latest may correct this?

  I tried to find the latest drivers for the touchpad Synptics in my ultrabook on the HP website, but it's the same old v16.5.3.3, I already have (published in may 2013). Synatics official site contains a link to the latest touchpad driver pack v17.0.19. Can I install it?

  I would try to install the Windows 8.1 (64-bit) driver Synaptics touchpad available in the download section of your sleekbook web support before using compatibility mode.  If the current driver does not work for you, try the earlier versions available .

  If you have no positive results, then use the compatibility mode (select Windows 8) on all three Windows 8.1 synaptics touchpad drivers, starting with the most recent.

  To use compatibility mode to install the driver just softpaq to the right, click on the file and choose troubleshoot compatibility. Select Windows 8 and run the installer.

  The following video has a decent explanation, but the Narrator does not get to the point for a bit. Go directly to the minute 4 and watch it from there.

• Internet Explorer does not open in the metro interface

  My IE does not open in the metro interface. This is my default browser & I disabled all add-ons. What can I do now?

   

  Hi Wendy,.

  I understand that you can access the modern user, Internet Explorer interface, but desktop Internet Explorer works fine. To better understand the question, please answer the following questions:

  (1) what exactly happens when you try to open Internet Explorer to the modern user interface?

  (2) has received no message/error code?

  (3) what are the changes to the system prior to the question?

  (4) you are able to access other applications for the splash screen?
   
  (5) you are able to launch the desktop Internet explore?
   
   
   

  Method: Please delete the following registry key

  Warning: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it.

  (a) go to: HKEY_LOCAL_MACHINE\Software\Microsoft\Windows NT\CurrentVersion\Windows\AppInit_DLLs

  (b) delete the value: (C:\PROGRA~2\WI3C8A~1\Datamngr\datamngr.dll C:\PROGRA~2\WI3C8A~1\Datamngr\x64\IEBHO.dll)

  (c) reboot and retry launch browser IE10 Immersive

  Important: Serious problems can occur if you modify the registry incorrectly. For added protection, back up the registry before you edit it.

  Back up the registry:
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry
   
   
   

  Hope it solves the problem, if you have other questions about Windows, feel free to post.

• my photo does not work with the screen saver

  Photos has never worked on Apple TV 4 until today with the 032116 update, but my pictures does not work with the screen saver.

  I dare you to try to tell me how to make it work. Please have a solution, someone.

  Given that Apple isn't really care or help on these forums, it would be great if someone mentioned the steps.

  Thank you

  Can you elaborate on the question?

  These are user forums and this is why you will not see the participation of Apple here

• 2.60 BIOS does not work on the Satellite A200 - 22 c

  Hi all

  I made the mistake to Flash my old bios Satellite A200 - 22 c (PSAE6E) to the new version 2.60.

  As I did this, the keyboard does not work on the bios screen, so I am unable to manage anything in the BIOS.

  When Windows Vista 32B starts the first time, the keyboard does not work. If I close the session and then I it again, it works correctly.

  The touchpad is lost and I need to use a USB mouse. Is not a pilot cause problem, all the drivers are updated and are working properly.

  The question is: why Toshiba didn't allow users to download the old version of the BIOS? ¿WHERE or who do I contact to get the original BIOS? Why do the flashing utility make a backup of the OLD BIOS and then does not give you the ability to recover it?

  Please, help me to recover the original BIOS to retrieve my keyboard and my touchpad because I can´t find any message or anything like that to get in touch with the technical support of this web site.

  Thank you!

  Which version was old BIOS?

  By the way: you can contact Toshiba. They have access to the Archives of BIOS and they can provide you with older version of BIOS.

• 128 - GB MicroSD card does not work with the new Clip +.

  My old Clip + (black, 8 GB) was getting very long in the tooth, so I ordered a replacement off Amazon.  As far as I know, it is identical to the old, but a very unpleasant difference is presented - it does not work with the MicroSD card which has been a huge part of why I got a Sansa at all.  He acknowledges, but after a media updated I'm lucky if more than one album appears.  And that's what's so crazy!  You just blow through the update in a few seconds, and when I navigate on the map, there is nothing or a handful of albums random, orphaned.  That's happened?  I updated the new Clip + for the current firmware (as I had done with previous); I made sure to reproduce all the parameters that I would be put in place before--I can't imagine what could be the cause!

  Treats quick closing:

  The card is formatted in FAT32 with the same sector size in storage aboard the player (32 768 bytes).

  A 64 GB card format works even without any problem.

  I tried to update the media in MTP and MSC mode; the problem is the same in both.

  There is ample space for MTABLE. SYS - I have not yet loaded all the music on the Clip + itself.

  Rockbox plays the card without problem, but the sound quality is horrible (at least on this player; I'm sure that other versions sound best), and its interface is a headache.  No thanks.

  HM.  Looks like to run CHKDSK /F on the map the problem resolved!

• Sansa Fuze does not work with the Xbox 360?

  I know that the console is capable of playing a MP3 player through it, I could do my job as Creative Zen. I don't understan why it does not work with the "rocket", the interface looks more simple on the surface of things. And I'm sure it doesn't because I don't have a HARD drive for my Xbox, it was working fine before.

  The reson I am, I wanted to know because I wanted to know the other ways of playing my rocket while listening. the kool on my expirimentation thing is I found that the Xbox will charge my rocket when it is off and I can listen at the same time. I also found that my Playstaion 2 will work also in this copacity all-in-on.

  Basically the Auto setting works well with the XBox.  Select settings > USBMode > MTP or MSC.

  With PSG, you can even play content protected by DRM rockets (IE Rhapsody) on Xbox.

• I had a computer repair man replace my hard drive and restore my laptop and now my orginal key does not work with the copy of vista it has installed and it won't validate.

  I had a computer repair man replace my hard drive and restore my laptop and now my orginal key does not work with the copy of vista it has installed and it won't validate how can I solve this
  I have an acer

  Diagnostic report (1.9.0027.0):
  -----------------------------------------
  Validation of Windows data-->
  Validation status: invalid license
  Validation code: 50
  Validation caching Code online: n/a, hr = 0xc004f012
  Windows product key: *-* - XY9X3 - JDXYP-6CJ97
  The Windows Product Key hash: xFQJU8srKsovk6p1Lk1yW93in4E =
  Windows product ID: 89583-OEM-7332157-00211
  Windows product ID type: 2
  Windows license Type: OEM SLP
  The Windows OS version: 6.0.6002.2.00010300.2.0.003
  ID: {F20B4B72-1308-45BE-8F90-95E91A3F0AAF} (1)
  Admin: Yes
  TestCab: 0x0
  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Product name: Windows Vista (TM) Home Premium
  Architecture: 0 x 00000009
  Build lab: 6002.vistasp2_gdr.110617 - 0336
  TTS error:
  Validation of diagnosis:
  Resolution state: n/a

  Given Vista WgaER-->
  ThreatID (s): n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002

  Windows XP Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  File: No.
  Version: N/a, hr = 0 x 80070002
  WgaTray.exe signed by: n/a, hr = 0 x 80070002
  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  OGA Notifications data-->
  Cached result: n/a, hr = 0 x 80070002
  Version: N/a, hr = 0 x 80070002
  OGAExec.exe signed by: n/a, hr = 0 x 80070002
  OGAAddin.dll signed by: n/a, hr = 0 x 80070002

  OGA data-->
  Office status: 109 n/a
  OGA Version: N/a, 0 x 80070002
  Signed by: n/a, hr = 0 x 80070002
  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->
  Proxy settings: N/A
  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
  Default browser: C:\Program Files (x 86) \Mozilla Firefox\firefox.exe
  Download signed ActiveX controls: fast
  Download unsigned ActiveX controls: disabled
  Run ActiveX controls and plug-ins: allowed
  Initialize and script ActiveX controls not marked as safe: disabled
  Allow the Internet Explorer Webbrowser control scripts: disabled
  Active scripting: allowed
  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->

  Other data-->
  Office details: {F20B4B72-1308-45BE-8F90-95E91A3F0AAF}1.9.0027.06.0.6002.2.00010300.2.0.003x 64*-*-*-*-6CJ9789583-OEM-7332157-002112S-1-5-21-923204104-223683984-168055983Acer Extensa 5630 Phoenix Technologies LTD.V1.30 20090319000000.000000 + 00070333507018400FA04090409US Mountain Standard Time(GMT-07:00)03ACRSYSACRPRDCT109

  Content Spsys.log: 0 x 80070002

  License data-->
  The software licensing service version: 6.0.6002.18005
  Name: Windows Vista, HomePremium edition
  Description: operating system Windows - Vista, channel OEM_SLP
  Activation ID: bffdc375-bbd5-499d-8ef1-4f37b61c895f
  ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
  Extended PID: 89583-00146-321-500211-02-1033-6002.0000-0042012
  Installation ID: 004511331255365043724851364501374781338933223323713385
  Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=43473
  The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=43474
  Use license URL: http://go.microsoft.com/fwlink/?LinkID=43476
  Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=43475
  Partial product key: 6CJ97
  License status: Notification
  Notification reason: 0xC004F063.

  Windows Activation Technologies-->
  N/A

  --> HWID data
  Current HWID of Hash: OgAAAAEAAgABAAIAAwACAAAAAwABAAEAeqjWy6pVxGJ6f0DXhgfkNoBBsJzy9ErM1F/eG4QdrFYqhQ is

  Activation 1.0 data OEM-->
  N/A

  Activation 2.0 data OEM-->
  BIOS valid for OA 2.0: Yes
  Windows marker version: 0 x 20000
  OEMID and OEMTableID consistent: Yes
  BIOS information:
  ACPI Table name OEMID value OEMTableID value
  APIC APIC PTLTD
  FACP INTEL CRESTLNE
  HPET INTEL CRESTLNE
  START PTLTD $SBFTBL$
  MCFG INTEL CRESTLNE
  SLIC ACRSYS ACRPRDCT
  ASF!            OEMID OEMTBL
  SSDT BrtRef DD01BRT
  SSDT BrtRef DD01BRT

  Ah! -in this case, it is not necessary.

  I see from my records that a similar case has been solved by uninstalling and reinstalling the update WAT - KB971033

  Open the Windows Update - click the link view updates installed on the left of the page

  in the list, find the WAT update KB971033, and then uninstall it.

  Then restart and reinstall the update from here - http://support.microsoft.com/kb/971033

  redemarrer restart again, then try to change your product key to the one on the sticker - what is happening this time?