STG access numbers do not work: they do not respond

Twice in the last month, the access number for my STG does not work. I compose, but no response, no voice prompts, etc.

The first time that I have updated my online site, which has not changed the access number, but does not seem to put something else because it started to work again. This second time this thing did not work. I also tried two other access numbers in Sacramento, California, and they did not work either, just the silence.

Access numbers that do not work at the moment are (all U.S..):

(530) 554-1364
(916) 756-4248

(916) 596-3019

Fixed! And it turns out to be the residential gateway to AT & T (modem/separator/WAP gizmotron) that was the problem. AT & T has sent a new (different model entirely) and once connected the access number for Skype-to-Go has worked.

No thanks AT & T so. I'm sure that AT & T knows that they have modems problem, but they never admitted this way:

Me: I don't think it's a problem of AT & T. I'm going back to Skype to try and work with them.
Cat at & T Rep: try to replace the residential gateway and see if it works.
Me: But why he would only block numbers from Skype?
Cat at & T Rep: I'm going to go ahead and process the order in lieu of the residential gateway.
Cat at & T Rep: as far as I am concerned, it will be a problem with Skype.
Me: ok
Cat at & T Rep: However, you and I don't want to give any reason to Skype, when we return to the question.
Cat at & T Rep: so for this reason, let us go ahead and replace the RG and see if it works.

Tags: Skype

Similar Questions

  • the numbers do not work keyboard

    numbers does not work on my keyboard (wireless) 1-9 do not have zero work, I Remover the bluetooth keyboard and I'm trying to connect it again, but once again, I now use numbers to configure the bluetooth

    Read this article on the Apple Knowledge Base

    If your Apple wireless mouse, keyboard or trackpad doesn't work as expected - Apple Support

  • Access code did not work, now iphone 6s is off the display to connect to itunes

    Access code did not work, now iphone 6s is disable showing connect it with itunes, futher when I connect with I phone I started to update and there is the mode of recovery after 15 min do not know what to do

    Restore is the only option here.

    If you have forgotten the password for your iPhone, iPad or iPod touch, or your device is disabled - Apple supports

  • Portege R500 - TrueSuite Access manager does not work with IE 8

    TrueSuite Access Manager does not work with Internet Explorer 8

    Version:
    Internet Explorer: 8.0.6001.18702
    TrueSuite Access Manager 2.1.23.0

    Any idea?

    Thankx
    Robert

    Hello!

    Which laptop computer and operating system you have?
    And what do you mean with it doesn t work? You get an error message or something else?

    You must give us a little more information. Otherwise, we can t help you my friend.

    Good bye

  • T410i numbers do not work except the 5 and 6

    Having a problem with the normal numbers does not.

    This has nothing to do with them being dirty or who need to be replaced, nor is the number lock on.

    None of the numbers works except the 5 and 6.

    If I'm in firefox by typing in the google search bar when I press 1, for example, the keypad will beep, firefox will switch to full-screen mode and the text box will start to AutoFill with 1111111111. does any number is pressed. except the 5 and 6.

    Similarly if I am in word, except that it will bring up save as box and start to auto-fill in the name of population with 111111

    The only way I can type 1 at the present time is to use the on-screen keyboard.

    I've done the fn nmlk nmlk capslk, combos and is not her back.

    I restarted and it is always the same.

    Thanks for watching!

    I am running Win 7 pro

    the keyboard was defective. He had a small amount of cash months ago, and it took all this time to make the problem appear.

    a keyboard replacement and everything's fine. Thanks for the pointers!

  • VeriSoft Access Manager does not work on Windows 7.

    VeriSoft Access Manager does not work on Windows 7. It worked on Windows Vista and 7 RC, but it now gives the error "this program blocked to compatibility problems. VeriSoft Access Manager is not compatible with this version of Windows. For more information, contact Cognizance Corporation. "He said that the problem file is AsGHost.exe. Any ideas how to solve this considereing that has worked in Windows 7 Release Candidate?

    This software is not yet compatible with Windows 7. I met the same problem. You must use different software to fingerprints. DigitalPersona works very well and can be downloaded from the HP website. Here is the link...

    http://h10025.www1.HP.com/ewfrf/wc/genericSoftwareDownloadIndex?LC=en&DLC=en&cc=us&softwareitem=ob-56930-1

  • upgrade to the new mac pro and tries to install CS6. Application of serial numbers of CS5. They are not in my list of product, just numbers CS6.

    I have all my products listed in the section "Products registered" site, BUT the serial numbers listed do NOT allow me to complete the installation process. She asks the CS5 serial number to complete and of course, these numbers are not hanging out for me to make reference to. Where these figures are included in my product list?

    Hi Frankr4757535,

    I hope you were able to locate your serial number CS5. If not, this can help: find the serial number of your product Adobe quickly. If not, please contact customer service. Click on the blue button that says: "Still need help?" and select "chat". Chat technicians are unable to provide for the older products troubleshooting techniques, but they can find your serial number.

    Best,

    Del

  • Some hyperslinks in the exported PDF file takes the Viewer to the pages "broken/missing. For example, the hyperlinks to specific of Youtube videos does not work, they brought to a youtube page is missing.

    Some hyperslinks in the exported PDF file takes the Viewer to the pages "broken/missing. For example, the hyperlinks to specific of Youtube videos does not work, they brought to a youtube page is missing.

    Hi Sarah!

    I solved it! I had to use the original URL shorter links to create

    functional hyperlinks or try to short the links using Google URL Shortener.

    I don't know why it worked by doing this, but he did!

    With the friendly and happy greetings!

    Sonny. A

    2015-11-24 9:32 GMT + 01:00 aadeshs76610910 [email protected]>:

    You talked

    by aadeshs76610910

    https://forums.Adobe.com/people/aadeshs76610910?et=notification.mention> * in

    Re: A few hyperslinks in the exported PDF file takes the Viewer to

    pages "broken/missing. For example specific Hypertext to Youtube videos links

    does not work, they will bring to a youtube page is missing. in Adobe

    Community *-view aadeshs76610910 you reference

    https://forums.Adobe.com/message/8209923?et=notification.mention#8209923>

  • ADE 4.5 keeps freezing ("not responding") when I plug my Bebook mini E drive. When I unplug the E drive it immediately starts working again. I tried different versions of the ADE (2.0, 3.0, 4.0, 4.5) but they all have the same question. How can I fix?

    ADE 4.5 keeps freezing ("not responding") when I plug my Bebook mini E drive. When I unplug the E drive it immediately starts working again. I tried different versions of the ADE (2.0, 3.0, 4.0, 4.5) but they all have the same question. How can I fix?

    His player on this list: Adobe Digital Publishing Solution?

  • Three computers networked fine then suddenly the error message «...» Contact the administrator of this server to find out if you have access permissions. Not enough server storage is available to process this command. "

    I had a network that worked very well with three 2 computers running Windows XP Professional and Windows XP Home Edition 1. Suddenly, the network has just stopped allowing certain communications giving the above error message (I have another thread address with XP to Vista computers). The main computer with XP Pro, I'll call A, the second computer with XP Pro, I'll call B and third with XP Home will be C. All computers can share files and printers then without any changes to the system that occurred the following:

    A can access the documents and printers on B and C

    B may NOT have access to documents or printers on one, but access to documents and printers on C

    C cannot have access to the documents on one, but CAN access A printer and CAN access the documents and printers on B

    When access is denied error message is displayed:
    "\\A\My documents is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Not enough server storage is available to process this command. "(\\A\ being the computer that I am trying to access)

    As I said access from all computers on this network was working fine a week ago and there has been absolutely no changes made to the network. I checked the following

    1. workgroup name on all computers are the same
    2. file and printer sharing are enabled for all computers.
    3. all computers may been from each computers just denied in some cases.

    The firewall that runs on all three machines is AVG and there were no changes to the one last week, but I checked that sharing is allowed.

    I even tried to run the Configuration Wizard from the network on all computers to see if it works, but the same exact problems occur after doing this.

    I met this problem now THREE times. I can't believe that I'm the only one who has this problem and I can't believe that there isn't a solution for it. None of the Microsoft documentation has even a hint of a solution for this specific problem.

    I need a solution that closes completely the network at my church, and they cannot afford to buy printers and others for each of their computers.

    This error message is misleading. See article Knowledge Base Microsoft Antivirus software may Cause Event ID 2011 for a likely solution, specifying a value of IRPStackSize 15 on A computer.
    Boulder computer Maven
    Most Microsoft Valuable Professional

  • Ipv6 access list does not apply autonomous Aironet 3602I-E

    As you can see in the attached config I configured two SSID (2G & 5 G) for a third (2G only) SSID and PEAP WPA2-Ent on the vlan 2 for 'poor team access as guest '.

    Basically I forced the Dot11Radio0.2 interface in the Group of deck 1 to get all three SSIDS on vlan 1 (since I want just a quick way and dirty to allow its customers access to the internet, without having to configure a vlan separate everywhere).

    The guest SSID (XX COMMENTS) allows tkip in addition to BSE and uses a PSK rather than PEAP. Access lists configured on Dot11Radio0.2 IPv4 allows clients connected to this SSID get an IP by DHCP, use the DNS servers on the local network and access the internet. All other traffic for the local network is blocked by access lists guest_ingress and guest_egress.

    This all works very well, ipv4 is blocked for guests invited as expected. However, ipv6 is something different. For some reason, the ipv6 access list is completely ignored.

    Because I don't need ipv6 for guest access, I thought that I have completely block and do with it. As you can see I have this set:

    interface Dot11Radio0.2
    guest_ingress6 filter IPv6 traffic in
    guest_egress6 filter IPv6 traffic on

    and these ipv6 access lists have a rule of "refuse a whole" only. Yet, the XX COMMENTS SSID connected client gets an ipv6 address of the server on the LAN DHCP6 and has full connectivity. For ipv4, that I had to explicitly allow DHCP packets to the client not even get an IP, so the ipv6 access lists are not clearly applied.

    No matter if I move the access interface Dot11Radio0 instead lists, they don't do anything. I thought that maybe I should add a "enable ipv6" on the Dot11Radio0.2 interface (even if ipv6 traffic was very good, even where it shouldn't), but when I set "enable ipv6" Dot11Radio0 or Dot11Radio0.2 the radio goes into a sort of infinite loop of reset:

    000261: Sep 23 2016 22:32:50.512 it IS: % DOT11-5-EXPECTED_RADIO_RESET: restart Radio Dot11Radio0 interface due to the reset of the interface
    000262: Sep 23 2016 22:32:50.516 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
    000263: Sep 23 2016 22:32:50.524 it IS: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
    000264: Sep 23 2016 22:32:51.516 it IS: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Dot11Radio0, state change downstairs
    000265: Sep 23 2016 22:32:51.560 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
    000266: Sep 23 2016 22:32:51.568 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
    000267: Sep 23 2016 22:32:51.576 it IS: % LINK-5-CHANGED: Interface Dot11Radio0, changed State to reset
    000268: Sep 23 2016 22:32:52.608 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to
    000269: Sep 23 2016 22:32:53.608 it IS: % LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed State to
    000270: 22:32:53.608 Sep 23, 2016 it IS: % DOT11-5-EXPECTED_RADIO_RESET: restart Radio Dot11Radio0 interface due to the reset of the interface
    000271: Sep 23 2016 22:32:53.612 it IS: % LINK-6-UPDOWN: Interface Dot11Radio0, changed State to down
    etc.

    In addition, when creating a list like this ipv6 access:

    guest_egress6 IPv6 access list
    refuse an entire ipv6

    The other is automatically created:

    IPv6-guest_egress6 role-based access list
    refuse an entire ipv6

    A deletion also removes the other.

    What is happening with these ipv6 ACLs, why they are not blocking all traffic? Why do I get an acl "role-based" too? Is associated it with?

    Is there a another way to kill just any ipv6 on the SSID of COMMENTS XX traffic while leaving alone on others? That's all I need at this stage. If the ipv6 ACL do not work, perhaps this can be done (ab) using a service-policy or policy routing? I'm ready to creative solutions :)

    PS. I know this is not the recommended method to configure a guest SSID, but it should still work IMO.

    You have encountered a bug I discovered a few months ago (CSCva17063), in your case, the workaround is to apply the ACL on the physical rather than the void interface interface (because you want to completely block IPv6 in any case). I write (more) my conclusions regarding the traffic that refusal on autonomous APs in a blogpost, might be interesting for you to read as well.

    Remember that the access point used as a bridge between the wired infrastructure and wireless, not as a router. There's some IOS routing of commands (like the "enable IPv6" command you pointed out) , but these are not the characteristics that should be used or need to be enabled on an access point.

    Because the networks internal and customer spend somewhere else, I would perform filtering on this device instead. Also sub gi0.2 interface is missing from your configuration, so I do not think that access as a guest is currently working at all?

    Please rate helpful messages... :-)

  • "No access to the network" problem in Windows 7 and error message "your computer seems to be correctly configured but the device or resource (DNS SERVER) is not responding."

    Hello, I have a desktop PC and a laptop (DELL Inspiron N-4050).
    I have problem with my internet connection cable which is working fine on my PC, but does not not on my laptop giving an error "no access to the network.

    When I troubleshoot it says "your computer seems to be correctly configured but the device or resource (DNS SERVER) is not responding."
    I said to many technicians of microsoft online response, but they could not solve my problem and said this is my DNS problem and advised me to contact my Internet service provider. Guess it's because of my internet so why it works on my PC not on laptop?

    Yesterday, my ethernet cable pulled out my cell phone and I couldn't connect to the internet more. But on my desktop PC, it works perfectly fine. (I do not use wifi, if this information is also required) I have studied several threads with similar situations, and I have tried different methods to solve the problem to no avail. I did a system restore, but I'm having no luck. Also, I did not of the latest changes with my anti virus software and my LAN card drivers look to date.

    When I remove my cable from the laptop and again connect my cable then it works but only after the PC sat for awhile.
    1.I did flush DNS by typing "ipconfig/flushdns" in the command prompt.
    2. my IP address, DNS, subnet mask etc are set to automatic.
    3.I also added physical address taken from command line giving "ipconfig/all". for the properties of the network driver settings.
    4.I ' installed the drivers to date of 2014 on my laptop.
    5.I did a lot of searching the web, but they do not solve my problem.

    Please help me to solve it.
    I appreciate your help.
    Thank you.

    Hello Hall,

    Please keep us updated on the status of the issue.

    I suggest you to follow the steps in this Microsoft article troubleshooting and check if it helps:

    Error message "your computer seems to be configured correctly, but the device or resource (DNS server) is not responding" in Windows 7

    http://support.Microsoft.com/kb/2779064/en-us

    Hope the helps of information.

    Please reply with the results, in order to help you solve the problem.

    Thank you

  • Need help: Reader does not start, the message error "attempt to access an address not valid."

    My previous installation of the drive (Windows 7, 32 bit) worked without any problems.  Until a few days ago when I updated to the latest CD player.  Installation worked fine, but when you try to start the CD player, I received the following error message: "attempt to access an address not valid."  I uninstalled CD and installed Player 11.0.  Yet once, installation worked fine, but I get the same error message, even if double click directly the Adobe Reader .exe file.

    A similar question was asked in December 2014, but I do not see a resolution.

    Without Adobe Reader, many applications simply do not work.  Any help would be appreciated.

    Adobe Reader Error Message 2015-10-18.jpg

    Thank you, Christopher, but this thread did not provide the right answer to my situation.  However, I continued working on my problem and finally found the solution: it's software Msreader EMET let go.  This software is an absolute disaster.  This is a free Microsoft security software. It's great, but once installed on your system, you cannot uninstall it even more.  After an EMET update a few months ago, I could not start Microsoft Word program.  After hours of play and even communicate with their support (not), I finally understood that he was own EMET software Microsoft blocks the Word Microsoft to start program.  Apparently, these guys don't know what they are doing.

    Anyway, I was ready to uninstall and reinstall the drive again, this time using the cleaner of Adobe's Acrobat Reader software to remove all possible traces of before install.  Before I did that, I remembered the EMET disaster a few months opened EMET, unmarked all actions AcroRd32.exe, and voila, launched reader and let me not open PDF files. (I had to reboot my PC before that worked).  Player is then proposed to upgrade to the latest version.  I did, and big surprise, Reader produces the same error message after the update.  Heck!  But after another reboot, the drive launched without any problem (apparently, EMET for the additional restart to recognize the changes after the update).

    I lost the greater part of the day to work on this issue, but I'm a happy camper again, because my Acrobat Reader works again.  Maybe my experience will help someone else.

  • Import a Word file, the numbers do not continue after an image

    We import large Word files that are full of paintings step/Action with pictures that separate tables. Here is the output of another tool files. RH5 that importation of tables and numbers are hard coded - they are not the numbers of HR, but are all there.

    In the first RH7 table has a 1 in the step column and it is numbered article HR. The table has 2 rows - a header and a single line stage. An image of the screen is displayed below. Then the table 2nd step/Action.

    In the 2nd table... and all the tables below the 'Step' column is empty in the line where the number should appear. The header is fine. All of the text in the title of the Action is very good. But the number of step is missing.

    These files have anywhere from 20-100 + steps. It is a major issue for us. Anyone have any suggestions on how to fix/change? For the moment, we are hand numbering... not everything simply will not work as a long-term solution.

    All suggestions are accepted with gratitude!

    Peter solved this problem! The answer is to save the file in Word as 'filtered Web page. " This apparently changes the auto-numeros in hard-coded numbers and they import perfectly. BLESS, PETER! I imagine that there are other "gifts" of the Word who may benefit from this solution, so it is very good to know.

    As always, the Forum has saved my butt and you all true experts out there... know we moderate authors appreciate your time, energy, expertise and willingness to share it all! Without you we would be absolutely dead in the water.

    Save as Web page, filtered. What a solution! Take care...

  • The numbers "could not open file for some reason any."

    Suddenly some of my documents of numbers prompt response "numbers" could not open file for some reason any ' "the document is unavailable. Other documents numbers remain accessible. My backup versions invites the same response when I try to open them. Is there a solution?

    Hello Fred,.

    Thanks for this info and choosing the communities Support from Apple. I know how important is able to open all your files in numbers is for you!

    If I understand correctly, you cannot open some files of numbers even from backups, but others continue to work. To limit this problem, I would suggest starting with the following steps:

    1. first of all, run disk utility and check for questions on your hard drive, as hard drive problems can lead to situations like yours.

    Disk utility (Yosemite): a disc repair

    2. then, you can test this in a new user, to refine, if it's a question broad system or specific to your username.

    How to test a question in another account on your Mac.

    See you soon!

Maybe you are looking for

  • Install a new graphics card

    I tried to install a new amd (sapphire hd 7950) to my computer hp p6-2083sc. I couldn't do it because of unseemly threads. Is it possible to get these two together? the page for AMD: SAPPHIRE TECHNOLOGY Radeon HD 7950 - 3 GB GDDR5 - PCI Express 3.0 (

  • where can I get from the center of solutions for windows 7 for my C7280 all-in-one?

    I connected by usb and now I can print wireless from my computer but can not scan to the computer without solution centre. My original disk does not support windows 7.

  • Call log / history of calls

    Can I access / change the call log (aka the call history)?

  • burned by another router through vpn

    Hello Here's the deal: RV042G ROUTER1 ROUTER2 I have a RV042G connected to a router '1' (LAN1) via a VPN. I have another ('2' for LAN2) router behind the local '1' with another network router (no bridge, a different IP address). For now, I PING the I

  • Looking for a way to test the keyboards with mini-DIN connectors 6-pin!

    My wife has an older Compaq Presario with 1.0 GB of RAM and a 200 GB hard drive.  I recently bought a HP with 4 GB of RAM and a hard drive 1.0 TB.  This is a sweet machine after you run the old PC for years! All my devices connect with USB Sockets. I