Stock HP Pavilion p6-2260ea case fan

Similar Questions

• HP Pavilion HPE h8 - 1070t CTO need case fan

  HP Pavilion HPE h8 - 1070t CTO, product number: LP028AV #ABA

  After an error message, on the fan and case fan noise I replaced the AVC DS09225R12MC234 DC 12V case fan 0. 3A with a Startech.com FAN9X25TX3H case fan.

  A program to monitor I have shows an increase in rpm of the system another fan. I'm trying to find out if my new fan is correct or adequate propper case fan.

  Hi checkit, as long that all fans are working and they doesn't make unusual noises or work allways on the maximum RPM is fine, Adi.

• Replacement HP Pavilion a6667c case fan

  Hello

  I would like to order a case fan of after-market for a HP Pavilion a6667c desktop replacement. We know the size of the fan and connector type? I have no physical access to the computer to check myself, but must be ordered in advance.

  Thank you

  Greg

  The reference is: 5188-3722.  You can google this number.

  It's a 92mm casefan. Care is standardized.

  Prices range from $6.50 and more.

• HP Pavilion a1220n Desktop PC fan (FANIN1) making the noise

  my desktop HP Pavilion a1220n (FANIN1) exhaust fan making a noise.  start-up noise, RPM fan drops of about 960 (no noise) to 750 (noise).  I guess that the fan will stop at some point soon.

  Anyone know the name / plug for this fan, so I can buy a replacement?

  I opened the folder and the fan noise starts, I hit the fan and the noise goes away for a few minutes and then go back.  not the best solution.  If the fan stops, and since it is the exhaust fan, can I keep running my PC with the box to open?  Is the fan at the bottom of the case, not the cooling fan in the CPU.  I guess when the case is open, I get a lot of air so that when the fan stops completely, I can always run the PC.

  Sorry for hiking...

  I-) ihor

  ihorhp,

  The stock rear exhaust fan is a 92mm fan. Part of HP # is 5187-5223. See here

  As discussed here

• Precision T3500, two case fans 80mm Arctic F8 down time of 81C at 70 ° C

  Hello

  I just replaced the CPU of stock in my Precision T3500, passing from an e5520 to 5660 x.  Both processors will heat up beyond their TCase, 72 and 81.3 C respectively, values when you use the passive heatsync of Dell in copper stock.  Y at - it an active heatsync available for this system?  Heatsinc OEM installation uses downs bolt female rather than the male standard ones.

  In addition, I notice a 5 c difference between my coolest temp core and the next coolest temp core and a 8 c split between my core cooler and warmer heart.  Is this normal?

  Thanks in advance,

  SoC

  Hello Chris,

  Today, I received two 80mm Arctic F8 case fans with an adapter fan 3 pin molex.  The difference in thermal performance is deep.  I have attached four photographs, one of the fan box, one of the back of my case, one inside my case, the molex adapter, and a thermal profile up-to-date.

  With the last test after installing fans, the system seemed to stabilize round 70 C.  Although, I let only the test and monitor run for 15 minutes approximately.

  I hope that this cooling method to others.

  Thank you

  SoC

  

  

  

  

• HP 700-414: what case fan coolers and CPU would fit into a 700 HP - 414

  I installed a GTX 950 in my HP 700-414 played overwatch for maybe 3 or 4 hours max and my time cpu has reached 85 - 87 c and my gpu is between 80-85 C. So I was wondering if you guys know how I could find the size of the case fan and how many mounts for fans are available? Because I can't find anything on it I searched and searched. And do you think I could adapt a CPU cooler to spare in this case?

  Hello92, welcome to the forum.

  The time of your video card do not seem to be too bad.  The absolute maximum for the GTX 950 is 95 C.  Ideally, you do not want to keep at least 10 to 15 C lower than that which is yours according to your figures.  Your time CPU however are much too hot for me.  When OC I am very cautious and want to see time about 50 C.

  You may need to get a little inventive when it comes to add case fans.  It's always a balance.  You can actually get fans to work against the other.  In other words, a fan air may cause another do not work effectively.  Trial and error is the best way to go.  When the fans run correctly, you will see an increase in cooling.  In addition, it probably not places to mount fans.  This can be overcome by using velcro or other means.  There's not enough connectors, so you will need to use adapters.

  After walking coolers are normally very large.  You will need to measure carefully to make sure that the cooler you choose to insert in the case.  I have recommended a Cooler Master Hyper 212 EVO to a member and it was too big.  Cooler Master makes some very good, but you must find one that will fit in your case.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• Pavilion P6-2260ea, recovery disks won't laod on new hard drive.

  I have a Pavilion P6-2260ea who started running very slowly and crash intermittently.  Self-assessment of DPS ran the disk, the drive specified result was suspect and should be replaced.  I bought a Seagate Barracuda SATA drive to replace the SATA Hitachi in the machine.  Unfortunately, that I had not created so recovery discs I bought at HP.

  The Seagate is now installed but when I put the recovery disk 1 in the drive ROM its starts to load windows files, then the error.  I ran the DPS Sef Test against the new drive and it is successful, then the new drive seems to be ok and recognized, I think?

  Windows is loading files...

  Windows Boot Manager

  Windows has encountered a problem communicating with a device connected to your computer.

  This error can be caused by unplugging a removable storage device, such as an external USB drive while the appliance is in use, or by faulty hardware such as a hard drive or a CD-ROM, which fails.  Make sure that all removable storage is properly connected, and then restart your computer.

  Status: 0xx00000e9

  Info: An unexpected i/o error has occurred.

  At any time the Ollie.

  I am pleased to have been of assistance.

  I forgot that your PC has usb ports 3.

  You cannot use those when you try to boot from a flash drive (at least not until the 3 Windows USB drivers are installed, which they were not).

  Sorry, the recovery disks did not work.  It was a lot of quid to spend on something that did not work!

• a replacement for Hp Pavilion dv6 6120-ee (fan)

  Hi I want to buy a replacement of Hp Pavilion dv6 6120-ee (fan) and I can't find well I found my laptop model, so I want the link to buy everything online that I can't find it online, I want to just order it I don't want not taken in charge or something else because the support is useless , so I want to just the link to buy it (not not looking for ((parce que je l'ai fait mais je ne trouve pas il Bien?)), then press purchase if you can help me to write the link in comment thank you)

  Product number: A2B56EA #ABV

  What do I want? : the mentioned laptop fan

  Thank you

  Hello

  Data sheet: http://support.hp.com/us-en/document/c03003964

  You need HP 641477-001 part number

  Manual: http://h10032.www1.hp.com/ctg/Manual/c02842252.pdf (Page 30, 90)

  HP part store: (not available)
  http://PartSurfer.HP.com/search.aspx?SearchText=641477-001

  Online store:
  http://m.eBay.com/ITM/HP-Pavilion-DV6-6000-dv7-6000-Fan-Heatsink-650797-001-641477-001-665309-001-/111086784282

  http://www.Amazon.com/GP/AW/d/B00IWMO0TU?pc_redir=1411901582&robot_redir=1

  http://www.Amazon.co.UK/GP/AW/d/B008L2ZRTI?pc_redir=1412813518&robot_redir=1

  http://m.eBay.co.UK/ITM/original-new-HP-640425-001-641477-001-639404-001-641578-001-CPU-cooling-fan-/161154352679

  http://m.eBay.IE/ITM?Itemid=310938742373

  Concerning

  Visruth

• size of tc - 605 Acer pc case fan?

  I am trying to add the new fan in my pc acer tc 605 case, but I do not have this size fan can fits into the rear slot of your case?

  sukup6,

  According to the link below, you can measure distance between the holes to determine the size.  I think a fan 80mm or 92mm fan will work, but not quite... remember as it has been a while since I measured.

  Also, there are a couple of molex available on the harness of the ps... so it will be "always on" full speed at less than case fitted with a speed switch fan.  It isn't a sysfan of work on the motherboard to auto regulate the fan speed.  So you might want to consider a case fan which includes a 3 speed switch, if you're not running full speed all the time, even at idle.

  http://www.TomsHardware.com/answers/ID-1716550/measure-fan-size.html

  An example of a case with a three-speed switch fan:

  http://www.Amazon.com/Antec-TriCool-DBB-cooling-3-speed/DP/B00066ISF2

  I have a case in my tc - 605 fan, so take my opinion with a grain of salt.

• Case fan runs at full speed

  I accidentally shorted the circuit case fan on my motherboard HP (explanation below), and now the fan runs at full speed all the time. Apart from the fact that it was a stupid thing to do, it will be a long term problem and should I try to reset the fan speed switch?

  (Long version) It's hot here these days and my computer fans seemed underpowered. I put a splitter at the exit of the case on the motherboard fan and added a second fan in addition to the original fan. All it worked well except the new fan seems to run pretty slow. I wanted to get a voltage reading card fan, but I accidentally hit the two sensors on my voltmeter and the computer shuts down immediately. He has started up and worked well, except that the throttle was no longer working and the fans were running at full speed. This also explains why the second fan turned slowly before when they were both being strangled.

  I guess that in the end I got my wish to have my fans running at full power, I just wanted to see if there are future problems leaving this way.

  Hello design_guy,

  You should not have problems with the fan rotating at high speed, with the exception that you can reduce the life cycle of the fan.

  You can install software on the computer that will allow you to adjust the speed of the fan to the computer which may help you extend the life of the fans and give you a bit of control over them.

  Something like SpeedFan should do the trick.

• Dell Studio XPS 9100: Case fan care? Cooler CPU upgrade options?

  I want to upgrade the case fans in my XPS 9100, but I've seen much contradictory info in the actual specifications regarding size: are these 92 mm or 120 mm?

  In addition, it is an i7 960: is there a compatible upgrade for the CPU cooler? I don't want or need to COO liquid: want to let it cool a bit. Basic time are constantly around 52 C.

  I think that on all processors in the LGA 1366 socket, the hoses are the same.  On the 9000, I used the cooler DBX - B on 4 different processors in the LGA 1366 socket.  Any socket LGA 1366 cooler should operate, regardless of the CPU.

  The DBX - B can be installed to direct the air in 1 of the 4 directions, depending on how it is mounted.  I have mine pointing upward, to the power supply.  (Note fan blows air in the direction of the fins in aluminium).  Idea is to keep the heat away from the other components of the motherboard and direct it to two fans at the rear (one being in the power supply), which are tailpipes.

• What is the case fan just to get to a m9426f

  I need a case for hp m9426f fan it says it's a foxconn model PV902512Lwhere can get me a

  Thank you

  I ordered this one low Gelid Silent FN - PX09 - 20 9 92mm TC temperature controlled case fan silent 38CFM 11 ~ 23dBA

• Elite E91XX: CPU/Case fan help please

  Hello

  I got my Elite e9150t for over a year and I was very happy with it. This Christmas, I've added a video card MSI GTX460 with a cooler ventilated internally. The video card use on 150W under full power and it is not a little too hot for my taste.

  My PC is in a custom-made in the office with the construction of ventilation in. The Office currently has a USB-powered fan that pulls 17 ft3/min, and I'll add two more this week. I hope that will solve my problem, but if it is not my next step is to upgrade the case fan in the PC. It's really painful to remove the desktop PC, so I'm hoping to get some answers here.

  From what I see the fan is a 92mm unit. I don't see the brand name, what type of connector, there or CFM rating.

  Of you can look at the fan in your system to e91XX of elite and give me some info that you can find on the fan? The fan has a 3Pin or 4pin on the motherboard connector? It blows out or in the case?

  Thanks in advance,

  Chris

  Chris,

  I use the EVGA GTX 460 1 GB but not the EA model (venting).

  You must still understand how to get fresh air in the office and the hot air outside. More ventilation top and bottom will help you. You may even consider using some fans to stream manipulation.

• HPE - 590t: Suggestions for replacement CPU Cooler & case fan

  Hi all

  I would like to replace the fan in my HPE - 590 t.  Recently, he made loud noises and yesterday it sounded like a car was at my house with the idling of the maximum RPM.

  I know that some have recommended the Coolermaster Hyper 212 EVO in previous threads, however I have some concerns regarding this cooler would fit in my case, as it seems that I have about 1.5 inches of space to the left of the cooler and about 1' of headroom above the stock cooler.

  Here are the specs for my motherboard.

  I have a case of average size, I would be grateful any recommendation for the appropriate CPU cooler.

  Ideally, I'd like something that could last another two years and be as quiet as possible.

  HP DV9310 Windows 7 Professional 4 GB RAM
  
  DV7t-6100 Windows 7 Pro 8 GB RAM
  

  Ruette,

  I wanted to let you know that you were right about the question of the back plate on the motherboard.   I decided to order the aftermarket cooler that I mentioned, and when I went to install it, it appeared to be welded directly on the motherboard.  I was puzzled because I've never seen such a design.

  Because I could not remove the back plate, I couldn't install the new heatsink.

  Being faced with the choice of either ordering a heat sink used as you have suggested to the origin or the HP part since the website claiming to sell the stock heatsink heat, I decided to remove my HP Elite system and build a custom system.

  I built a new system with a motherboard MSI Gaming 5 and 4790 k i7 processor and used the ram, power supply, SSD, GTX 750 ti and other components in my system HP Elite for my new build. All these elements I just mentioned were anyway under a year of age.  Of course, I had to spend money on a Windows 7 operating system at retail, but also a new case, but overall it was worth the money. I also think that in the end I started to the cultivate my HP and it was just time for me to upgrade.  Now, that I'll stay with custom desktops built and stay away with OEM computers due to the unusual limitations that the OEM wants to place on their systems.

  Thanks again for all your help!

• HP Pavilion p7-1233w: case swap questions

  I made some recent improvements made to my PC. These include an additional 8 GB or RAM, for a total of 16 GB, a 500W power supply, and a MSI Radeon R9 280 / 3GB GPU. The new GPU itself hardly fit into the existing casing. Then with all the extra stuff in there, my time become too high for my taste so I put the cover on the case. So Ive done turn it opened these days. Ive had a case of full size of an old computer. Its got an extra fan in the side panel and a place for a 120mm fan on the back instead of the 80 mm, I currently have. Moreover its got a side clear cool panel so you can see all my cool lights and stuff lol.

  Sort of, I was looking at all the connections. The case I want to put things has a few different things. The main thing I noticed was the front USB connectors. The case of HP has a big plug for USB 3.0, but if I have looks like it has just a USB port and taking in the case is different. The headphone jack and the microphone looks the same.

  For the HARD disk and lights power wires and the switch are different, but it looks like they are just separated, while each of them in the case of HP are in a jam. But it looks like they'll all hold the plug if I put them right. I just need to know what are those who go on the pins.

  Im not worried about making the 15 in the work of part 1 card reader. I haven't used an any of them since I got the computer and they just collect dust though.

  Hello

  The following image shows the pinout which is common to several headers in front. Only the LED pins are sensitive to polarity.