Stop: 0x0000007e (0xc0000005, 0f748e0bf, 0xf78da208, 0xf78d9f08)

Similar Questions

• STOP: 0X0000007E (0XC0000005, 0XF748E0BF, 0XF78DA208, 0XF78D9F08) pci.sys - address F748E0BF base at F7487000, Datestamp 3b7d855c

  I am trying to install windows XP Pro on a new computer.

  I get same seizure starts to install is that I published under the title.

  Help me... I'm out of ideas... and can't find answers anywhere.

  Running with

  Asus P7P55D Deluxe Motherboard
  Intel i5 quad 2.66 processor
  4 GB of ram
  EVGA GeForce GT 220 ssc edition 1 GB DDR3 video card.

  I cannot go beyond this error and cannot find a solution...

  :(

  In your case, I would like to start by #4 below.

  Do not install an operating system is usually caused by (in order of probability):

  1. you are trying to install with other devices connected to the computer. Unplug them before trying to make an installation.

  2. "" "" defective installation media. "" Check the CD/DVD installation for scratches, tasks. Try another machine.

  3. bad optical drive. Test with another CD/DVD bootable or Exchange for a well-known work.

  4. faulty RAM. Test with Memtest86 + www.memtest.org . You will download the .iso image file to create a bootable cd. Burn the file with the third party burning software *-as an image, not in the form of data. Then start with the media that you did (you may need to change the boot priority in your BIOS so that the optical drive is the first boot device). The test runs immediately. The test run for an hour or two--at least that errors are seen immediately. If you get any errors, replace the RAM.

  * A good free choice ImgBurn comes from www.imgburn.com .

  5. bad hard drive. Test with a diagnostic utility downloaded from site of the disc mftr... You create a bootable CD with the files you download. Burn the file with the third party burning software *-as an image, not in the form of data. Boot with the CD that you have done and do a full test of the reader. The physical tests fail, replace it.

  6. other hardware components are faulty. MS - MVP - Elephant Boy computers - don't panic!

• Impossible to reinstall Windows XP error: BSOD STOP: 0X0000007E (0XC0000005, 0XF78DA208, OXF78D9F08)

  Original title: BSOD

  tried to reinstall windows xp bsod STOP: 0X0000007E, (0XC0000005, 0XF78DA208, OXF78D9F08 * pci.sys_address more numbers to several numbers and a date stamp.)

  Hello

  1. How are you trying to install?

  2 do you use a full version Windows Setup disc or the recovery disk?

  3. at what stage of installation you get the error message?

  I suggest you try the steps from the link below and check if it helps.

  http://support.Microsoft.com/kb/330182

  Additional information:

  How to fix a computer that does not start: http://windows.microsoft.com/en-US/windows-xp/help/setup/how-to-fix-computer-that-will-not-start

  Hope this information is useful.

• Blue screen with STOP: 0x0000007E (0xc0000005, 0 x 00000066, 0xba4dbc40, 0xba4db93c)

  How to fix blue screen with STOP: 0x0000007E (0xc0000005, 0 x 00000066, 0xba4dbc40, 0xba4db93c)

  These accidents were caused by the corruption of memory (probably a driver).  Run these two tests to check your memory and find which driver is causing the problem.

  If you are overclocking reset all default before running these tests.
  In other words STOP!

  1 - Memtest.

  * Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. "http://www.memtest.org/#downiso"] Memtest86 + - Advanced Memory Diagnostic tool

  * Boot from the CD and let it run at least 5 or 6 passes.

  Remember, anytime Memtest reports errors, it can be bad RAM or a bad motherboard slot.

  Test the sticks individually and if you find a good, test it in all slots.

  Any error is indicative of a memory problem.

  If a well-known stick fails in a slot of motherboard, it's probably the slot.

  http://www.SevenForums.com/tutorials/105647-RAM-test-Memtest86.html

  2. Driver Verifier

  Using Driver Verifier is a dubious proposition. Most of the time it will crash and it will tell you what is the driver. But sometimes it will crash and will not tell you the driver. Sometimes it will crash until you can connect to Windows. If you can't mode without failure, then you will have to resort to editing the registry offline to disable driver verifier.

  I suggest that you first back up your data and make sure you have access to another computer so you can contact us in case of problems. Then do a system restore point (so you can restore the system using the functionality of Vista/Win7 Startup Repair).

  In Windows 7, you can do a startup repair disk by clicking Start... All programs... Maintenance... Create a system - with Windows Vista repair disc, you need to use your drive installation or from the "Repair your computer" option at the top of the Safe Mode menu.

  So, here is the procedure:
  -Go to start and type "auditor" (without the quotes) and press enter
  -Select 'Create a custom settings (for code developers)' and click 'Next '.
  -Select "Select individual settings from the list complete" and click "Next".
  -Select the entire document except for "Low resource Simulation" and click "next".
  -Select "Select driver names from a list", then click "next".
  Select all drivers that are NOT provided by Microsoft, and then click "Next".
  -On the next page, select "Finish".

  Restart the system and wait as he crashed to blue screen. Continue to use your system normally and if you know what are the causes of the crash, do it several times. The objective here is to get the system crash because Driver Verifier is stressing out the drivers. If it is not planted for you, then let it run for at least 36 hours of continuous operation (an estimate on my part).

  If you are unable to Windows because it crashes too early, try safe mode.
  If you can't mode without fail, try to use the system from the installation DVD restore to bring the system back to the previous point of restoration that you created.
  http://www.SevenForums.com/tutorials/101379-Driver-Verifier-enable-disable.html

  Further reading
  "http://support.microsoft.com/kb/244617"] using Driver Verifier to identify issues with Windows drivers for users advanced

• Blue screen - Stop: 0x0000007E (0xC0000005, 0xF77AF756, 0xF7A0A430, 0xF7A0A12C)

  Original title: need help with Stop: 0x0000007E (0xC0000005, 0xF77AF756, 0xF7A0A430, 0xF7A0A12C)

  Can someone telll me how fix an error that says "Stop: 0x0000007E (0xC0000005, 0xF77AF756, 0xF7A0A430, 0xF7A0A12C)"?

  If the message under your STOP error message indicates this (probably not):

  WUSB54GCx86.sys - address 92 D 89498 base at 92D7c000, Datestamp 45c04cc9

  So the response from Microsoft support technician can help you.

  If the message under your STOP error message indicates this (most likely):

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED

  So the response from Microsoft support technician is not worth reading.

  If this is the case and you have an AMD processor, you must look at this article:

  http://support.Microsoft.com/kb/953356

  If we knew what was your system brand and model and a few other details when you made your initial post or someone have asked a few questions, you would have probably solved this problem in one or two cycles of message, but now 6 days.

  It is the shame that the MS Answers forum does not ask for any kind of information system when a new question is asked and we know absolutely nothing about your system.

  Not knowing the basic information a problem prolongs the frustration and the agony of these issues.

  Thank you MS Answers, allowing the resolution of simple problems as frustrating and a lot of time as possible.

• Message Stop 0x0000007E (0xC0000005, 0xF880E9AC, 0xF89359B4, 0xF89356B0) when to stop or restart the computer.

  Original title: message of stop 0x0000007E (0xC0000005, 0xF880E9AC, 0xF89359B4, 0xF89356B0).

  Hello. I am running windows xp sp3 (sp2 initially update) when I try to stop or restart my computer I get a blue screen that says stop: 0x0000007E (0xC0000005, 0xF880E9AC, 0xF89359B4, 0xF89356B0)

  Kbdclass.sys-
  address F880E9AC
  F880E000 base
  datestamp 48025372
  Help, please.

  Hi monicashannon,

  1. are you experiencing this problem after installing Service Pack 3 or you have made other changes to your computer?

  2. what processor you have on your computer?

  You can follow this link & check if the problem persists:

  Error after you upgrade a computer that uses one processor other than a processor of Intel for Windows XP Service Pack 2 or Service Pack 3 for Windows XP: "STOP: 0x0000007E"

  Reference: How to troubleshoot a Stop error 0x0000007E in Windows XP?

  Hope the helps of information.

• Blue screen error STOP: 0x0000007E (0xC0000005, 0x8Ac18874, 0xF792A468, 0xF792A164)

  Original title: blue, impossible to restart screen

  System: Dell Dimension 3000, Windows XP Home - SP3.

  Problem: I recently installed the new memory (now has 2G), check that the memory has been recognized and work.  Computer worked fine for several hours, with a noticiable improvement.  Then received warning from McAfee "A Trojan had been identified" and the computer had to be stopped to fix.  Not sure if this was related to the new memory, but the moment was just a few hours apart.  When I tried to restart the computer - I got a blue screen of death with the following technical information: * STOP: 0x0000007E (0xC0000005, 0x8Ac18874, 0xF792A468, 0xF792A164).  I can't start the computer in safe, except the Mode modes safe mode with command prompt and to my level of skills making me much good.  Please notify.  Thank you.

  Hi mysticskier,.

  Follow these methods.

  Method 1: Disconnect all external devices such as printer, scanner, etc.

  Method 2: Follow the steps in the article.

  You may receive a Stop error on a blue screen when you start a Microsoft Windows Server 2003-based computer or a Microsoft Windows XP-based computer

  http://support.Microsoft.com/kb/893239

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

• Blue screen: STOP 0x0000007e (0xc0000005, 0xb585d083, 0xba4c74ac, 0xba4c72a8)

  Original title: STOP 0x0000007e (0xc0000005, 0xb585d083, 0xba4c74ac, 0xba4c72a8) an idea how to solve this problem?

  Working on a dell desk top... no idea how to solve this problem?

  Perhaps the problem then. SP3 was recently installed on it? If it was you have to maybe do this

• The installation blue screen: STOP: 0x0000007E (0xC0000005, OxF748E0BF, OxF78DA208, OxF789D9F08,

  Original title: cannot format the new hard drive because when I boot the system disk it stops with several STOP error.

  I am trying to solve problems with desktop Dell XPS 420 of my daughter. He started with the message 'bootmgr' trying to get the windows computer.  She ordered a new hard drive and when it was physically connected, I put put in place the disc in the computer to boot from to install windows XP, but it always comes to the blue screen with the following error: (I'm not an expert on computers so that any help must be in a very basic language).
  STOP: 0x0000007E (0xC0000005, OxF748E0BF, OxF78DA208, OxF789D9F08,
  PCI.sys-address F748E0BF base at F7487000
  DateStamp 3b7d855c

  I retried the boot and got the same error.  I check the forums online and they suggest that to go in safe mode.  I can't go in safe mode - do not have an operating system installed yet.  Some have said to change organic caching and shadowing.  I don't know how to do and I can't get into safe mode.  I don't know what to do.  Of course, the warranty was out - 2008 computer.

  Can anyone help or point me in the right direction? My funds are limited to pay Dell for the solution.  Thank you.

  MDT? Does not look good. See:

  http://www.computing.NET/answers/hardware/MDT-hard-drive/23869.html

  I still don't understand why you think that you need a new hard drive. There is nothing prevents you to install own XP on the old disk.

  If you can't find the right drivers (I don't know where to find them), maybe you can get in Dell's BIOS and change the hard drive controller affecting IDE or legacy or something like that. Then the new disc would work.

  Or you can simply put the back of an old man. You can either try to repair your installation of Windows with our help or opt to perform a clean installation.

• WinXP error message Stop: 0x0000007E (0xC0000005, 0x00000000, 0xBA50F7C4, 0xBA50F4C0)

  Dear technical support

  I have a laptop running Windows XP Home edition SP2, just installed iTunes version 10.2.1 for iPhone 4. With the iTunes app runs in the background when you plug the iPhone 4 on the laptop USB port, blue screen with error message about the likely BIOS execution cache shadowing... or VGA card with the following information;

  Stop: 0x0000007E (0xC0000005, 0x00000000, 0xBA50F7C4, 0xBA50F4C0)

  I need help to solve this issue.
  Thank you.

  Jason

  Download bluescreenview install race it. What did he say? I would also like to upgrade to SP3. Because SP2 is no longer supported

• Given to nine Compaq 7700, BSoD, boot XP infinite loop, can't even get past the black screen to enter Windows. STOP: 0X0000007E (0XC0000005, 0XF773B15F, 0XF78D2520, 0XF78D221C)

  Help.

  I just got a refurbished Compaq 7700. It has Windows XP for drives of the refurbished computers.

  I try to boot from the hard drive (HD) and infinite loops, it is never past the initial home screen (black with blue status bar).

  I can't open the safe or the HD mode, it freezes at kmxstart.sys and then restarts again.

  Original title: given to nine Compaq 7700, BSoD, boot XP infinite loop, can't even get past the black screen, to enter Windows.

  I tried to boot from the disk and created Windows appears, then load the files, but then automatically tries to start Windows (without repair option). It then jumps to the BSoD with error code (after advice to verify sufficient disk space, to disable the driver identified, to change video cards, BIOS updates...)

  STOP: 0X0000007E (0XC0000005, 0XF773B15F, 0XF78D2520, 0XF78D221C)

  Usbccgp.sys - address F773B15F base at F7737000, DateStamp 480254d 2

  Apparently, this driver is a printer driver? I don't have a printer, but do not know how to disable it without access to windows.

  I got a new Philips 18.5 "monitor, an optical mouse and a keyboard with it.

  My guess is that the screen is the problem, because it was full again when I received and therefore not tested with the system before shipping. Not sure about the mouse and the keyboard.

  I tried a few options in the BIOS screen as well, but no dice.

  Help! Before shipping the brand new...

  I thank you and have a wonderful new year.

  Craig.

  Howdy Daavee and Shekhar,

  I hope that your day is going well.

  It turns out that it was the hard drive, it was defective. The new unit arrived and it works beautifully. Thank you very much for all you help. I wish you a happy new year.

  Craig.

• How can I fix this stop: 0x0000007E (0xc0000005, 0x25FFCCCC, 0xF78E10BC, 0xF78E0DB8

  I have the cd for reinstallation of operating systems, windows xp professional with service pack 2, but it came when I tried to reformat stop: 0x0000007E (0xc0000005, 0x25FFCCCC, 0xF78E10BC, 0xF78E0DB8.

  Hi Sir mike,

  1. you receive the error message during formatting of the hard drive or reinstalling Windows XP?

  This problem may occur if a system thread generates an exception that the error handler does not catch. This exception can be caused by the following:

  (a) If this issue occurs after the first restart during Windows Setup, or after installation is complete, the computer may be not enough disk space to run Windows XP.

  (b) the computer BIOS may be incompatible with Windows XP, or it might have to be updated.

  (c) the video card drivers may be incompatible with Windows XP.

  (d) a device driver or a system service might be damaged.

  (e) if the problem is associated with the Win32k.sys file, it can be caused by a control program remote third.

  See the Microsoft articles below and check if its useful.

  How to troubleshoot a Stop error 0x0000007E in Windows XP

   

  http://support.Microsoft.com/kb/330182

  Error after you upgrade a computer that uses one processor other than a processor of Intel for Windows XP Service Pack 2 or Service Pack 3 for Windows XP: "STOP: 0x0000007E"

  http://support.Microsoft.com/kb/953356

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• BLUE SCREEN of DEATH error CODE * STOP: 0X0000007E (0XC0000005, 0X8050D532, 0XF78A23B8, 0XF78A20B4)

  I just tried to turn on my computer and I got the black screen that gives you the choice to start in Windows XP or the Recovery Console, and when I click Start in Windows, it loads and then I get a quick death blue screen displays a down error code, and the computer restarts automatically. When I disable automatic reboot in the advanced options I get the blue screen showing this code: * STOP: 0X0000007E (0XC0000005, 0X8050D532, 0XF78A23B8, 0XF78A20B4) I tried this code on Google and got no results. I'm sure that I don't not miscopy, I checked several times.  I tried to start in safe mode, but then I get a black screen with many codes (w-a-a-a-a-y-y-y a lot to copy down) and the computer restarts. Someone knows what to do? I have a lot of important files out there that I just can't lose. Thank you! Any help or advice is appreciated.

  Alex

  While this error can be caused by malware infection, it's commonly found when the RAM failed. In all cases, you want to go down the data files before you do anything else. Do this with one of the following methods:

  1 remove the drive and put it in a box of USB drive or use a USB adapter. Attach it to a computer that is running a working XP/Vista/Windows7 installation. Use the work of Windows Explorer to copy the data to the hard drive of the system to the rescue and burn data on cd or dvd. I prefer not to do it if I know the drive is infected because he has a chance to infect your host system. In these cases, I use #2 below.

  2. you can start the target computer with a Bart PE (if you use XP) or a Linux live CD like Knoppix and retrieve the data in this way. General information about the use of Knoppix for this are:

  You will need a computer with two cd records, one of which is an engraver of CD/DVD OR a USB thumb drive with sufficient capacity to store your data, OR an external hard drive formatted USB FAT32 (not NTFS) *. Download Knoppix .iso image file and create your bootable CD. If you do this in a previous (XP or Vista) operating system, you will need the third burning like Nero, Roxio or the free ImgBurn software (Windows 7 can burn .isos natively). Burn as an image, not in the form of data. Then boot with the CD that you created, and Knoppix will be able to see the files in Windows. If you use the USB key or an external hard disk, right-click on its icon (on the desktop) to get its properties and uncheck "read only". Then click on it to open it. Note that the mouse action by default in the window manager used by Knoppix (KDE) is a simple click to open instead of double-click traditional MS Windows. If you want to burn CD/DVDs, use the K3b program.

  * My understanding is that you can now write on NTFS from Linux partition. If you wish to do this, Google for instructions on the use of the NTFS driver.

  http://www.Knoppix.NET
  http://www.nu2.nu/pebuilder/ - Bart PE Builder

  When you have your data safely, get hardware troubleshooting with the RAM before reinstalling Windows. There is no point in trying to install Windows if your material is not good.

  http://www.elephantboycomputers.com/page2.html#Reinstalling_Windows

  And for future disaster recovery programs:

  http://www.elephantboycomputers.com/page2.html#Backing_Up

  If you can't do the work yourself (and there is no shame in admitting this isn't your cup of tea), take the machine to a professional computer repair shop (not your local equivalent of BigComputerStore/GeekSquad). MS - MVP - Elephant Boy computers - don't panic!

• STOP: 0X0000007E (0XC0000005, 0XF17FC30B, 0XF8AB7ADC, 0XF8AB77D8)

  Computer was working fine, then the screen became all monochrome (but not blue, off-white).
  This occurred during a comprehensive analysis of Microsoft anti-virus program «Securities Essentials»
  The computer is itself kept running as I could hear the ongoing fans and LEDs are stayed on.
  Unable to see anything or if she was responding to keyboard or mouse movement entries I turned it off.
  When the computer reboots, initially it seems to be OK, going through the process of the usual display of Windows XP on startup. He was even on the screen where it shows the different user accounts. But then 2 seconds later got the following error message:

  ----------------------------------------------------------------------------------

  A problem has been detected and Windows has shut down to prevent damage to your computer.

  If this the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow

  the following steps:

  Make sure you have enough disk space. If a driver is identified in the stop message, disable the driver or

  Check with the manufacturer for driver updates. Try changing video cards.

  Check with your hardware vendor for updates to the BIOS. Disable the BIOS such as caching memory options or

  the occultation. If you need to use Safe Mode to remove or disable components, you restart the computer, press F8 to

  Select the advanced startup options, and then select Safe Mode.

  Technical information:

  STOP: 0X0000007E (0XC0000005, 0XF17FC30B, 0XF8AB7ADC, 0XF8AB77D8)

  SiS163u.sys - address F17FC30B base at F17F8000, DateStamp 41ab05b9

  Beginning physical memory dump
  Total physical memory dump.
  For more assistance, contact your system administrator or technical support group.

  ----------------------------------------------------------------------------------

  Probably from about 5-7 years old eMachine race T1150 pre-installed Windows XP Home Edition.
  1.30 GHzz/celeron to Intel processor.
  What follows is also on the case - "3D Intel Direct AGP Graphics", I think it's the chipset.

  No new material has been added or deleted in over a year.
  Recently the Microsoft "onecare.live.com" scan and difficulty.
  After that, I installed the Microsoft «Securities Essentials» Supposedly without concern for quality, virus protection for your PC at home of Microsoft.
  It seemed to install OK and I could do a quick scan & difficulty.
  The problem occurred in the middle of the analysis I did later.
  Turned off and on again and received the same error message.
  Shot and a third time and got into safe mode.
  I tried "using last good known configuration", but I got same result.

  Also during the installation of Microsoft "Securities Essentials" uninstalled various antivirus programs (program at the request of the main titles") that were on the computer. One of them could have been something called EMCO Malware destroyer.

  Known solutions or ideas?

  FYI - the system and software came pre-installed & I don't think they gave me a CD with XP on it, so a solution that doesn't require you to put the CD in the dvd player is going to be my only option.

  You go to the website of the mftr. (Trendnet here) and download the drivers. It's the only place wherever you get them unless you have recorded the CD originally supplied with the unit. Usually, you can reinstall the drivers, but if there is an entry in Add/Remove programs and uninstall the device first.

  Incidentally, be proactive in preparing for the inevitable:

  http://www.elephantboycomputers.com/page2.html#Backing_Up

  I say this not to offend you in any way or to suggest that you 're not saving, but if you don't are not then you should be aware that your computer has gone its normal end of life, so be prepared to die. Certainly, he could go for years but OTOH it would not be surprising if he does not. MS - MVP - Elephant Boy computers - don't panic!

• Blue screen, ERROR * STOP: 0x0000007E (0xC0000005, 0x824EC033, 0x88F03650, 0x88F0334C)

  Hi, I turn on my laptop with windows Vista Home Basic (Compaq) and I get a blue screen with this error:

  STOP: 0X0000007E (0XC0000005, 0X824EC033, 0X88F03650, 0X88F0334C)

  I tried with safe mode and all the options that windows and compaq gives, but everybody works, do you know what I can do? I want only the files in the hard drive, there is a solution?

  Thank you

  I used a Windows XP Live CD to backup my files, clean the data and reinstall Windows Vista... because I can't correct the mistake x_X

  Thank you anyway ^^