STP and PowerConnect 5548 battery

Similar Questions

• HDMI piling on PowerConnect 5548

  We have 8 switches PowerConnect 5548 and are interested in using the stacking of HDMI for 10GbE.

  We currently have all 8 switches under tension and production running on them traffic.  Each switch is currently either back 'a home run' to a Cisco switch, or connected to another switch PowerConnect 5548.

  • Is mature enough stacking HDMI technology for a production environment?
  • It would be important if each switch have been 'home run'd ' to the Cisco switch and each 5548 PowerConnect was connected in a loop HDMI?
  • Stacking HDMI technology would require restart us our switches to implement?  A failure would be necessary?
  • All the special items of note regarding the type of HDMI cable?  (i.e. owner or any which best buy HDMI cable work?)

  Thank you
  Jon

  Is HDMI sufficiently stable stacking of the PowerConnect 5548 for production?

  • Yes (100%)
    
  • None (0%)
    
  • A little, but you better pay attention to the comments I post... (0 %)
    

  • Total votes: 5

  Jon,

  Technology HDMI wroks ideal for stacking the PowerConnect 55xx series. You can use the HDMI ports on the 55xx for stacking well and not for uplink to a Cisco or other device.  Also, you can stack only as 55xx switches with other 55xx and running the same version of the firmware.

  On the 55xx, you don't need to reboot the switches, but just plug the cables to create the stack.  An algorithm is used to determine which members becomes master and members who become slaves.  In my view, that the master is determined by which switch has been powered as long.  Don't forget that if you have the switches on different subnets or VLANs, they are configurations will be now changed all switches will become like a big switch.

  The type of HDMI cable is important, you will need to consult the documentation that came with the switch, or you can download the Guide of the user to http://support.dell.com.  You need cables that provide a flow rate of 10.2 Gbps (maximum allowed by the HDMI specification).  Usually the cheapest cables don't provide this.

  -Victor

• Updated my iPhone6 to ios10 and now my battery heats up and does not load

  Updated my iPhone6 to ios10 and now my battery heats up and does not load

  I have never experienced this with another iPhone or iOS version

  Of course, it's a problem because I use my phone all day

  What troubleshooting steps have been taken so far?

  Have you completed a reboot, reset or restore such as recommended by Apple?

  Best,

  GDG

• I just replaced my battery and it says 'battery of Service '? The battery is new. I need to reset something?

  I just replaced my battery and it says 'battery of Service '? The battery is new. I need to reset something?

  Try resetting the SMC http://support.apple.com/kb/ht3964

• Why my iphone 6 becomes hot and drains the battery faster after updating ios 9.2?

  After upgrading my iphone 6 the new 9.2 IOS recently, I experienced some problems about heating problems and deplete the battery faster.

  Can someone please look at my post and help me?

  I have the same problem. Immediately after the update of this week my iPhone 6 has started to go crazy - overheating until it was rude to hold and the battery drains completely in the course of an hour or two. Problem continued for two days now. I tried a reset (holding down power and front button) and I thought that this had contributed, but as soon as I used any application the phone started its tumble again. Probably overheating is caused by the CPU to do something, but I can't say what. This doesn't seem to be a problem with a specific application - any activity seems to he left. It was working perfectly normally until the 9.2 update.

• Remove and reinsert the battery to reboot the computer from sleep mode

  When the computer goes into mode "sleep" due to inactivity, it cannot be started again until I completely remove and reinsert the battery. It is an Acer laptop with Windows 7 OS

  Hello

  References to Vista also apply to Windows 7.

  1 I want to erase the General corruption and repair/replace damaged/missing system files:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------

  Check the settings (BIOS/CMOS) that you can start and ensure that this suite of lan, Wake on modem and
  similar are not enabled.

  Shoot sleep problems - hibernation
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  Panel configuration-Control Panel Home view (non-conventional) in the top-right search pane
  type of hibernation - see turn Hibernate on / off

  All the default power plans and then set them as you wish.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• G61 does not illuminate unless I have remove and replace the battery.

  Even when the power cord plugged in it will not light. If I remove and replace the battery it lights mode battery and AC. At the same time my HP Support Advisor and HP s Advisor "stopped working".

  I restore to a previous point, no help. Downloaded a new HP advisor, ho help.

  This happened after the recent big WIN7 updated. Help

  Hello

  In the Menu start, open the all programs, open accessories, right-click on command prompt and select "run as Administrator".  In at the prompt, type the following command and press ENTER.

  sfc/scannow                (Note that there is a space between sfc and /)

  Let the entire process, then the output type and press ENTER.  Stop the laptop, unplug the AC adapter unplugged, remove the battery and then press and hold the power button for a minute.

  Now, plug in the AC adapter without the battery inserted, start Notepad, open windows control panel, open Device Manager, expand the entry for the battery, on the right, click on and compatible Microsoft ACPI control method battery and select Uninstall - do uninstall not something else here.  When the uninstall is complete, shut down the PC, unplug the AC adapter, reinsert the battery and then start the PC on just the battery.  Windows will automatically reinstall the driver - leave Windows running for a few minutes. Shut down the PC again.  Now plug the power adapter (with the inserted battery always) and start the laptop to see if it helped the issue at all.

  Kind regards

  DP - K

• BlackBerry Smartphones how reboot or restart or refresh curve 8520 without removing and rebonding of battery?

  How to reboot or restart or refresh curve 8520 without removing and rebonding of battery?

  Soft reset:

  http://BTSC.webapps.BlackBerry.com/BTSC/ViewDocument.do;JSESSIONID=64C8797ED4CAB08C34C13D91377C1704?...

• computer falls asleep and only wake him up is to disconnect and remove the battery and it will come back, and then reinsert the battery it's a dell

  My computer is asleep and won't wake up. If I unplug the unit and remove the battery, it will be ok. Then

  I can reinstall the battery. It's a dell intel Insider core 13

  Hi Jim,.

   

  This problem may occur because of low battery or power problems. Please follow the instructions to solve the problem:
   
  Refer to the suggestion of Leo Huang dated Tuesday, September 14, 2010 09:01
   
  http://social.technet.Microsoft.com/forums/en-us/w7itprogeneral/thread/0866de60-A16B-41c4-8a6e-b56c848478f3
   
  Let us know the result. If the problem is still not resolved, we will be happy to help you further.

• is it not possible to load the game and load the battery other than through the xbox?

  Original title: play and charge

  I just buy a play and charge kit, it is said that it should be charged for 8 hours the first time, that I do not like to leave my xbox on 8 hours, I thought I could use one of these USB plugs that allow a device to be charged using a wall outlet, but I don't get all the lights on the controller No red light to show that the load, then is this not possible to load the game and load the battery other than through the xbox?

  Hello

  You can post the question here for assistance: http://forums.xbox.com/xbox_forums/b/xcsblog/default.aspx

• SMEs use solution and lenovo edge battery 430

  I brought a new lenovo edge 430 and in the internet, I hear lots of advice and guides on the use of the Li-ion battery as you shouldn't use it while in charge and blah blah blah.

  I am a regular user of portable every day and I have the following doubts

  1. I am always near a power source, should I remove the battery and connect directly to the ac?

  now when the load is 100% I unplug and use with battery and then recharge it again when it comes to about 30%. It is a good practice and the temperature that I rest is always less than 30 degrees.

  2. I have installed the small business lenovo solution tools, can I put after the operation hours in feature and connect the power supply and leave overnight for free? This will affect the battery life?

  3. can I install all the other tools vantage to think so?  I have 6 GB of ram not so no problem of speed.

  I'm more confused about the battery problem. Please guide me thank you!

  You can install the Lenovo Solutions Center (replaces the ThinkVantage Technologies) here:

  http://support.Lenovo.com/en_US/detail.page?LegacyDocID=LENV-DIAGS#LSC

  Then you can set all the parameters of the battery in the power manager, including ways to increase the longevity of the battery.

  You can charge it all night and set an upper limit and it will stop charging. (You can set it to stop loading at a certain percentage, for example, 80%)

  I hope this helps.

• Creation of the VLAN between Powerconnect 5548 and F10 s4810...

  In the coming months we will replace our network equipment.  I was able to get their hands on the new gear at the beginning, and if I'm not traditionally a guy from the network, the project has been given to me and I started playing.  The first thing that I wanted to work on was implemented VLANs.  I have configured the switches like the picture below:

  

  When I have IP every PC connected to the same subnet and apply VLAN10 to their respective ports, they aren't to pings within the same stack or between cells.  My basic understanding is that they are, do they not?  Did I miss something in my understanding of VLANS or is there a problem with my configs?  I posted the configs below.

  RTTMOACCESS01 config:

  database of VLAN
  VLAN 10,20,30,40,50
  output
  Add a voice vlan Yes-table Nortel___ 000181
  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
  Add a voice vlan Yes-table 00036 b Cisco_phone___
  Add a voice vlan Yes-table 00096e Avaya___
  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
  Add a voice vlan Yes-table Shoretel___ 001049
  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
  VLAN voice Yes-table add 00907 Polycom/Veritel_phone___
  Add a voice vlan Yes-table 00e0bb 3Com_phone___
  860 port address 0.0.0.0 iSCSI target
  port 3260 address 0.0.0.0 iSCSI target
  port 9876 address 0.0.0.0 iSCSI target
  port 20002 address 0.0.0.0 iSCSI target
  20003 port address 0.0.0.0 iSCSI target
  port 25555 address 0.0.0.0 iSCSI target
  hostname rttmoaccess01
  no console logging
  privilege 15
  !
  interface vlan 10
  Name IT
  !
  interface vlan 20
  name UserPCs
  !
  interface vlan 30
  name UserTCs
  !
  interface vlan 40
  the voice name
  !
  interface vlan 50
  Name printers
  !
  gigabitethernet1/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet1/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  gigabitethernet2/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet2/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag

  !
  Default settings:
  Service etiquette: 76BYTS1
   
  SW version 4.1.0.8 (28 August 2012 time 11:17:36)
   
  Gigabit Ethernet ports
  =============================
  Speed 1000
  full duplex
  negotiation
  flow control
  Auto MDIX
  no back pressure
   
  interface vlan 1
  interface port-channel 1-32
   
  spanning tree
  spanning tree mode RSTP
   
  basis of QoS
  QoS trust cos
  Enable IAS

  RTTMOACCESS02 config:

  database of VLAN
  VLAN 10,20,30,40,50
  output
  Add a voice vlan Yes-table Nortel___ 000181
  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
  Add a voice vlan Yes-table 00036 b Cisco_phone___
  Add a voice vlan Yes-table 00096e Avaya___
  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
  Add a voice vlan Yes-table Shoretel___ 001049
  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
  VLAN voice Yes-table add 00907 Polycom/Veritel_phone___
  Add a voice vlan Yes-table 00e0bb 3Com_phone___
  860 port address 0.0.0.0 iSCSI target
  port 3260 address 0.0.0.0 iSCSI target
  port 9876 address 0.0.0.0 iSCSI target
  port 20002 address 0.0.0.0 iSCSI target
  20003 port address 0.0.0.0 iSCSI target
  port 25555 address 0.0.0.0 iSCSI target
  hostname rttmoaccess01
  no console logging
  privilege 15
  !
  interface vlan 10
  Name IT
  !
  interface vlan 20
  name UserPCs
  !
  interface vlan 30
  name UserTCs
  !
  interface vlan 40
  the voice name
  !
  interface vlan 50
  Name printers
  !
  gigabitethernet1/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet1/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  gigabitethernet2/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet2/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  Default settings:
  Service etiquette: 76BYTS1
   
  SW version 4.1.0.8 (28 August 2012 time 11:17:36)
   
  Gigabit Ethernet ports
  =============================
  Speed 1000
  full duplex
  negotiation
  flow control
  Auto MDIX
  no back pressure
   
  interface vlan 1
  interface port-channel 1-32
   
  spanning tree
  spanning tree mode RSTP
   
  basis of QoS
  QoS trust cos
  Enable IAS

  Config RTTMOCORE

  ! Version 8.3.12.0
  ! Last modification of the configuration to Fri Jun 14 13:31:58 2013 default
  ! Startup-config updated Fri Jun 14 13:32:40 2013 default
  !
  start the primary system battery-unit 0: A:
  start a system secondary battery-unit 0: B:
  start the system stack-unit 0 default: A:
  start the primary system battery-unit 1: A:
  start a system secondary battery-unit 1: B:
  start the system default stack-unit 1: A:
  !
  redundancy full automatic synchronization
  !
  Hardware watchdog
  !
  no console logging
  !
  hostname rttmocore
  !
  disposal of battery-unit 0 S4810
  !
  stack-unit 0 battery-group 14
  !
  stack-unit 0 battery-group 15
  !
  interface TenGigabitEthernet 0/46
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  interface TenGigabitEthernet 0/47
  no ip address
  switchport
  FlowControl rx tx off
  no downtime

  disposal of battery-unit 1 S4810
  !
  stack stack-unit 1-group 14
  !
  stack stack-unit 1-group 15
  !
  interface TenGigabitEthernet 1/46
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  interface TenGigabitEthernet 1/47
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  !
  interface Vlan 1
  !
  interface Vlan 10
  Description IT
  Name IT
  no ip address
  Tagged TenGigabitEthernet 0/46-47
  Tagged TenGigabitEthernet 1/46-47
  Shutdown
  !
  interface Vlan 20
  Description UserPCs
  name UserPCs
  no ip address
  Shutdown
  !
  interface Vlan 30
  Description UserTCs
  name UserTCs
  no ip address
  Shutdown
  !
  interface Vlan 40
  Speech description
  the voice name
  no ip address
  Shutdown
  !
  interface Vlan 50
  Printers description
  Name printers
  no ip address
  Shutdown
  !
  Lldp Protocol
  !
  0 line console
  line vty 0
  line vty 1
  line vty 2
  line vty 3
  line vty 4
  line vty 5
  line vty 6
  line vty 7
  line vty 8
  line vty 9
  !
  end

  I would say lets start with one side and obtain communication of work between the two computers on the same stack at RTTMOACCESS01. The port settings for the 1/01 and 2/01 look great both in access mode for VLAN 10. Which IP addresses and subnets you assign to computers?

  5548 to battery power battery connection 10 also appear to not be in a LAG, then we run two connections like that and they aren't in a SHIFT, we create a loop and a single connection will enter a blocking state.

  For the connections between the 5548 and force 10, I suggest to turn them into a GAP. The command should look like this.

  Console > activate

  Console # configure

  Console (config) # (config) # interface tengigabitethernet 1/0/1

  Console (config) # port - 1 automatic mode group

  output console #.

  Console (config) #.

  Do the same for Te2/0/1

  Then we set up this OFFSET to set it up, and I would try to use the trunk instead of general mode mode.

  Console (config) # interface port-channel 1

  console switchport mode trunk #.

  console # permit trunk switchport vlan add 10,20,30,40,50 tag

  The same should be done for the Force switch 10.

  Te0/46.1/46 in a SHIFT

  Te0/47.1/47 in another SHIFT

  Put in the trunk and let the VLANS on the trunk.

  Allows to study these settings and see if we can make any progress.

  Thank you

• Aggregation of links between Powerconnect 7048 battery and battery S55 Force 10

  Hi all

  I'm trying to connect a battery 7048 with a stack of S55 (2 switches in each stack). I would use two ports (one on each switch) each battery to connect to each other. Can someone help me with the configuration of this please? I guess I'd go with LACP in this situation?

  If orders to fill what could be made, it would be much appreciated.

  Thank you, Carl.

  On the 7048, placing the ports in a SHIFT with LACP looks like this:

  Console (config) # interface gigabitethernet 0/1/2

  Console (config-if) active in mode channel-group 1 #.

  Console (config-if) output.

  Console (config) # interface gigabitethernet 0/2/2

  Console (config-if) active in mode channel-group 1 #.

  Console (config-if) output.

  Console (config) # interface port-channel 1

  Console (Config-if-PO1) #.

  And then configure the port channel but you need.

  On the S55, this tech tip article will guide you in the process of creating a GAP.

  http://bit.LY/1BO7tkS

  Let us know if you have any questions.

  See you soon

• PowerConnect 5548 and VLAN

  Good afternoon!

  I'm looking to implement a 5548 in our existing infrastructure. I want to preface this by saying that I am very new to networking.

  I'm looking to have at least two VLANS separated.

  -The first vlan for public sites face. These will have static public IP addresses.

  -The second VLAN is iSCSI traffic. I would like that it won't face public.

  Is it possible to Setup or should I be looking for a different solution.

  If possible, how should I go about setting up?

  Thank you!

  The port that connects to your router should be placed in Trunk mode with the VLAN you want in the trunk port. All ports are in VLAN1 access mode by default, this means that the port that plugs into your routing device is in access mode for VLAN 1 and VLAN 1 has internet access. For traffic VLAN 2 to access routing equipment that you will need to change cela port in Trunk mode and adds 2 VLAN as a VLAN Tag.

  468-page guide details where to put labeling.

  See you soon

• Need help to buy PowerConnect 5548 or 6248

  I currently Powerconnect 6248 and 6224 switches via my network.  On a floor 48 port switch is full and I need to add another, my thought is to add an another 6248 and stack them, but told me that I should get the 5548 and use sfp + 10 gig connection to connect to my 6248.  When I talked to my rep at Dell, he said he would not recommend it, but it might be possible.  Can someone tell me what would make the most sense?  Currently, we have data on the site servers and applications but will move them to a data center in the near future.

  The first thing that comes to mind would be to run as two stacked 6200 switches. When stacked it management makes it a little easier since the stacked switches act as one. It also less time spent on configuration with the addition of a member of the battery compared to a separate switch. Once 6200 switches are stacked you would also have the ability to Setup redundant connections by implementing a SHIFT that uses a port to each of the switches.

  On the other side of things, I'm not familiar with the topology of your network. So there may be a specific situation that is the reasoning behind this recommendation of people. They gave no explanation of why they would recommend the 5548 with connection sfp + on the stack?

  Thank you