Strange problem after upgrade OR-Scope

Similar Questions

• Latitude E5520 Audio problems after upgrade to win 10

  I have audio problems after upgrade to win 10 64-bit.

  Dell Latitude E5520 IDT 92HDxxx HD Audio
  Hardware ID:
  HDAUDIO\FUNC_01 & VEN_111D & DEV_76E7 & SUBSYS_1028049A & REV_1001
  HDAUDIO\FUNC_01 & VEN_111D & DEV_76E7 & SUBSYS_1028049A

  (1) if I use the built-in driver to Win 10 ("high definition Audio Device") I hear speakers/headphones and switching between the speakers and the works of helmet very well but my laptop computer microphone does not work ("not connected").

  (2) if I use the latest Dell driver (IDT 92HDxxx HD Audio Driver) I hear initially via speakers, but as soon as I plug in headphones I can't switch back to the speakers (i.e. switching between the speakers and the headphones does not work) and my laptop computer microphone works.

  I would be happy to provide more information and help to debug.

  To a Microsoft Community Forum, I received the following reply from Rob Brown - Microsoft MVP:

  *************************************************************************
  Hello
  AS OEM Dell is responsible for the good operation of the equipment both
  and Windows. Check their documentation online with Dell Support, and
  drivers and ask questions in the forums about known problems. Make sure that you are
  Run the latest version of the BIOS, chipset and drivers.
  I hope this helps.
  *************************************************************************

  I understand that the Latitude E5520 does not appear on the Dell "Computers tested for upgrade to Windows 10" list... However I was hoping maybe Dell could find in the goodness of their hearts to a updated driver IDT 92HDxxx... pretty please?

  Thank you
  John D.

  johnsdagg

  AS OEM Dell is responsible for the good operation of the equipment both
  and Windows.

  Hi, John. It's quite nervous of a member of the MS forum say that Dell is responsible to operate Windows. It wasn't Dell but MS who claims that Win10 has most of the necessary drivers and if not then the drivers Win7 and Win8.1 would work.

  johnsdagg

  I was hoping that maybe Dell could find in the goodness of their hearts to a updated driver IDT 92HDxxx... pretty please?

  I doubt that it is possible for two reasons. Dell went from IDT Realtek as the audio seller so probably not more a a contract with IDT, if IDT even exist anymore. A year ago IDT was acquired by another company. I do not know its current status, but it is sure that the acquiring company will not be upgrading old software IDT. Reference Dell itself does not write the audio drivers. Even when IDT was the seller I believe that Win7 drivers are the final versions - no version 8 or 8.1 I think.

  johnsdagg

  If I use the built-in driver to Win 10 ("high definition Audio Device") I hear speakers/headphones and switching between the speakers and the works of helmet very well but my laptop computer microphone does not work ("not connected").

  The native Windows audio driver can't stand struggling external mic. It is a MS 'known problem '. MS must implement a decision-making support, but there is no indication that it will be. Meanwhile, you have two workaround solutions. You can switch backwards between the natives and the IDT drivers. At some point Win10 could leave the IDT driver works correctly. Or get an outlet cheap usb audio to the microphone. Struggling running out-audio driver usb Windows native usb and so dependent no driver IDT.

• iPhone 6s + had some problems after upgrade to iOS 9.3.2

  1st issue is the battery. Already before the upgrade to iOS 9.3.2 since iOS 9.3.1 my battery iphone 6 s + last latency time approximately 40 hours. Now after the upgrade to iOS 9.3.2,and it last only 15 hours. I noticed that the battery went from 100% to 60% in 8 hours without using it. I change all the settings after upgrade.

  2nd question is Siri Spotlight search Suggestion. I see more suggestion of Siri (recent call log and recent applications) in the Spotlight search. I also noticed that, to start the Spotlight search, I need to get to the bottom of the home screen. Previously on iOS 9.3.1 when I push upwards, search Spotlight is cancelled and return to the home screen. Now in iOS 9.3.2,and it no longer works.

  I also-hard reset by pressing Start button / stop and the "home" button together until I see the apple logo. Who will not help too.

  Have you checked the battery in use/settings/battery? All apps using the battery more than usual?

  If the power to restart the phone did not help, the next step after that which could be set back to factory settings and restore form the last backup, especially if you updated using the option 'Over the Air '.

  Use iTunes to restore your device to factory settings - Support Apple iOS

  For some users, removal and establishment of post counts once again solved the problem for others, connecting to iCloud and connect again after you stop the farm by a restart of drain.

• Satellite L755-M1M3 driver sound problem after upgrade to win 10

  Salvation;
  I have problem with audio driver Toshiba Satellite L755-M1M3 after upgrade to win 10, the sound does not normally work in YouTube or Facebook even when I play the video files from my computer it is dug into the sound or noise goes, I update the driver but not help, can you help me please, I have Toshiba backup files how can I restore it?

  Inability of Toshiba to make the solution, always shocks me. !!! ???

• TFncKy.exe problem after upgrade to XP SP3 on Satellite A200

  Hello

  After upgrade of XP SP3, I have problem with TFncky.

  _System_:
  A200/PSAE7
  -XP Pro (2 x with OS selector, 1 OS XP XP main, 2nd XP for games)

  _Problem_:
  After booting XP from my main XP installation I always get an error message pop up stating that there is no prob with TFncKy and TFncKy should be stopped. As "signature of the problem" I get the following:

  + AppName: tfncky.exe AppVer: 3.22.0.0 ModName: ntdll.dll +.
  + ModVer: 5.1.2600.5512 Offset: 00012ace +.

  With one of the following keys on keyboard always results in above described error pop up but key are functional:
  WinLogo, DEL, HOME, PGUP /-DN, END, right SHIFT, FN + keys F etc.

  My second installation of XP (Lite for games) short smooth after SP3 upgrade: no error TFncKy error message.

  As my second XP runs without any problems after SP3 I'm not sure if the proplem is related with + tfncky.exe + or + ntdll.dll +.

  BTW:
  What driver package includes "tfncky.exe? Toshiba controls?

  Thanks in advance for any information or advice for this problem!

  Best regards
  Andreas

  Hello

  the problem was already discussed in another thread: http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=18082

  The last message was probably the solution for the whole of the case. The mentioned user that "TfncKy.exe" belongs to the Toshiba Hotkey utility that only needs to be removed and reinstalled for this problem.

  In addition, it would be wise to check the registry with CCleaner for example before you reinstall the Hotkey utility.

  See you soon

• Internet problem after upgrade to 10.11.3

  someone at face safari connection problem after the upgrade

  I'm having exactly the same problem.

  Is it possible to uninstall the 10.11.3 update and revert to the previous version?

• K3 Note Wifi problem after upgrade to the marshmallow

  Guys, after upgradation of Marshmallow in k3 note, there arise a problem of wifi, it just dropeout every minute like connect for 1-2 seconds and disconnect then automatic...
  If someone knows how to fix this please tell me... I have hard reset my phone but the problem is not solved... so please tell me the solution

  Note from the admin; phone added to the subject type

  
  

• WiFi problem after upgrade to Windows 10

  Greetings!

  I read a few posts on WiFi problems after the (improper) upgrade of Windows 10. I have a ThnkPad T530 which I've upgraded to Windows 10 Windows 7 in September (too late to roll back). Here's my question:

  I have three computers on my desk. This standard T530 running Windows 10, a ThnkPad E555 running Windows 7 and a Dell running Windows 8. I used all three last Friday. I installed Norton on all three Friday and everything went without a hitch. When I first started their return to the top of this morning, the two others came online as usual. The ThinkPad T530 connected by a router in the company, but has no access to the internet. I can connect to the hotspot on my phone and it connects fine. I tried to turn the WiFi connection and then turn it on again, restart, by killing and restarting the business connection, etc. Nothing changes.

  Help, please

  Ben

  Try the following:

  Open administrator command prompt:
  http://winaero.com/blog/how-to-open-elevated-command-prompt-in-Windows-10/

  Then, run this command:
  netsh int ip reset c:\resetlog.txt

• Dell XPS Ultrabook 12 has network using WIFI connection problem after upgrade to Windows 10

  I have a Dell laptop XPS Ultrabook 12 that worked fine on Windows 8.1. When Microsoft prompted me to sign up for upgrade to Windows 10, I hesitated, but finally, I signed up for it. In recent months, I have been asked several times upgraded to Windows 10 but I just ignored and delay the update as much as possible, because I need to work with the laptop and I can't afford to have problems after the upgrade.  To my horror, Microsoft forced an install of Windows 10 this morning without allowing me to delay and just after the upgrade, I can't connect to my existing network. I have therefore no access to the internet and I am currently typing this complaint using another PC. I noticed that the laptop can connect to the network automatically when I walk my router but the connection will last only a few minutes, and then he'd cut off. I tried to connect and the message I get is "unable to connect to this network. I checked with "ipconfig/all", wifi said media disconnected. I checked with the Dell support website and downloaded and installed a newer driver, but the problem persisted. Apparently the surf on the internet, this problem is faced with a number and any suggestions to fix do not work (after that I tried).

  Help, please.

  You should be able to go back to 8.1 for Windows by following the instructions here:

  https://www.YouTube.com/watch?v=2Y3uc2FWlK0&index=3&list=PL1RkaknDn7v-w5LEVIDvTCvmKZ_1_NcZz

• Latitude E5500 Intel GMA pixels problem after upgrade of RAM > 4 GB

  Hello, I use latitude e5500 with the following specifications:

  • Processor: intel core 2 duo
  • graphic: Intel GMA 4500 MHD
  • OS: Windows 7 SP1 64-bit
  • RAM: 6 GB (2 + 4) 800 MHz

  Recently I have upgraded RAM of 4 GB (2 + 2) 6 GB (2 + 4). They are of the same manufacturer, the two 800 MHz I checked the new memory with the Dell diagnostics - it's ok. After upgrade, I have a serious graphics - parts of my get pixelated screen problems. It is irregularly, with different applications ran - see the screenshot.

  I tried to uninstall the graphics driver - it's ok, but I'm not ;) mode 640 x 480 I have tried different drivers - no improvement. Also, I removed a 2 GB - it works very well with my new 4GBs

  

  Hello

  Yes, I solved the problem. I had to buy an another 4 GB from the same manufacturer with the same properties. With 4 GB + 4 GB, it works perfectly.

  Concerning

  Aleksander

• I will face any hardware problem after upgrade to Windows 10?

  Original title: upgrade Windows 10

  I have a Dell Vostro 1015 running windows 7 Professional. I am considering upgrading to Windows 10. Please advise if there are problems if I upgrade any hardware after upgrade to Windows 10, e.g. upgrade or downgrade RAM.

  Hello

  Thanks for posting your query on the Microsoft Community.

  With the description, I understand that you want to upgrade your Windows 7 operating system Windows 10 machine. I will certainly help you get this fixed number.

  I suggest you refer to the mentioned Microsoft articles below and check if this is useful:

  Upgrade to Windows 10: FAQ

  http://Windows.Microsoft.com/en-us/Windows-10/upgrade-to-Windows-10-FAQ

  Hope the helps of information. Please write back to us for any further assistance. We will be happy to help you.

• Keyboard problem after upgrade to 6.0

  Hello everyone

  I used 5.5 of Vmware Vsphere ESXI and Vcenter 5.5 without any problem of keyboard on the remote console on the guest operating system (win 7) after upgrade to esxi, vcenter 6.0 and 6.0, I have problems with the keyboard on the guest remote operating system, note I use french keyboard.

  french keyboard is also used by the operating system remotely.

  How can I solve this problem, so when I try the console remotely on the guest operating system display does'nt English keyboard us keyboard

  Thank you

  the problem is still persisting when using the web console, but when you use the remote console MRC the keyboard works normally

• HP 13-2106tu spectrum XT: Webcame problem after upgrade to 8.1

  After upgrade to win victory 8A 8.1 lost my webcame video/image. When I tried to open the cam aps or video Skype webcame light on but the cam does not work.

  No webcame driver found on http://support.hp.com/us-en/product/HP-Spectre-XT-Ultrabook-13-2100/5296014/model/5312995/drivers

  Its really disgusting...

  If possible, please give me solution.

  You can download and install the driver down the link and check if your webcam now works fine.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-123546-1 & CC = US & DLC = in & LC = on & os = 4158 & productOid = 5312995 & sw_lang = & Product = 5312797

• Strange problem after moving from the virtual computer to a new data store

  I am migrating our VM existing (8 in total) a 'problem' RAID to a new table on a new controller and am having a strange problem. Here are the steps I took (host OS is Ubuntu 8.0.4 LTS x 64):

  (1) off the power the virtual computer from the Web interface

  (2) the directories created for each virtual on the new RAID array computer (in this case a RAID 10 array on LSI 9750-8i controller)

  (3) rSync used to copy the data from RAID1 to be RAID2

  4) has created a new data store on the new RAID through the Web Server of VMWare user interface.

  (5) removed VM of the inventory through the Web, their return, added user interface then choose files .vmx on new data store on RAID2

  They have all power save fine... but three of them are not accessible on the network. I can open a console in the Web Server of VMWare user interface and they all run normally... but I can't their ping or access the respective virtual machine Web GUI. It seems quite arbitrary that those who work and those who are not. In this case... the VM that don't work is a license Autodesk, a Squid proxy server and a VM of cactus. All three of these virtual machines are 32-bit Ubuntu Server VM (two 8.0.4 and a 10.0.4)... and are the only Ubuntu VM on this host. It must be signifigant but I'm not see how.

  If I delete these three virtual machines of the inventory again and add to their original location (on the RAID1) they light up AND work normally. A consultant that we were working seemed surprised, as he had also done this experiment with some of the older VMWare products. I don't see how it would be the physical location of the files of the virtual machine. Any ideas?

  We rely on the migration to ESXi soon but in the meantime, we get these a few VM out of this RAID array problem. I'm stuck.

  Depending on the application, it may be enough to reconfigure the IP parameters (they are very probably on DHCP now) for the newly detected virtual NIC.

  André

• Display problems after upgrade to Yosemite iMac

  Since the upgrade to Yosemite my iMac has a very 'glitch '... screen Pixels flashing on the screen, all strange pixel following the mouse etc...

  When I boot in SafeMode the problem disappeared, so I guess that this excludes a graphics card problem. I had a reading and most other posts someone has suggested to run a script to determine the cause of the error. I did, but I know know how to decipher the output.

  Link to the old post office with the same question and suggested script etc: https://discussions.apple.com/message/30603036#30603036

  I ran the script Linc so kindly posted above and will display the results below:

  http://www.pastebin.com/embed_iframe/R5ATQcz1

  I was wondering if someone can see what the issue is and suggest how I can go back into service again.

  Any help would be great.

  Thank you very much

  Devs.

  Most people advise of not not to use cleaning programs. They can destroy the functioning of your computer as they may already have done.

  CleanMyMac2 uninstall

  After UN-installing use, this program to ensure that you have received all parts.

  EasyFind-replacement of Spotlight

  Uninstall Kapersky. His tendency to interfere with the operation of the computer while offering little or no benefit.

  Uninstall Kapersky

  Try to run this program, copy and paste the result in a response. The program was created by Etresoft, a regular contributor.  Use please copy and paste the screenshots can be difficult to read. On the screen with the Options, please open Options and tick the boxes in the bottom 2 before the race. Click on the button "Report share" in the toolbar, select "Copy to Clipboard" and then paste into a response. This will show what is running on your computer. No personal information is shown.

  Etrecheck - Information System