strange, puk, sound, on intervals

Similar Questions

• Strange question sound P30

  I have a new laptop P30 and I have a strange problem with the audio.
  It happens with the internal sound card as well as with a fireware external motu 828 audiocard (strangely).

  ((There are a lot of cracks and noises when no sound is playing... and it goes up and down when the hard disk or dvd) also with data) works.

  most strangely using headphones with internal sound card is no backgorund noise... and also with headphones connected to the audio card firewire... no noise at all. everything is clear and good.

  the strange thing is that the problem disappears when the laptop is on battery and no power adapter plugged.

  I'm going crazy with this... also because I manly use Notepad for recording audio...
  help resources!
  Simone.

  PSI changed cables and other things. .. but no difference
  audio turns off from the motu and analog goes into a blender and toaudio monitors. everything works well.

  Hello Simone

  You will be very happy boy if someone on the forum has experience with such things. In my opinion you should also check the MOTU support page. I'm sure that there must be someone with more experience to these specific questions.

  Good luck!

• Strange disconnection sound on Satellite L750-1KU

  Hello

  I have a strange sound disconection randomly on my laptop Satellite L750-1KU.

  I read on the forum, but it seems that there is no solution for this.

  My question is if there is a solution to our problem.

  PD: my laptop serial number is YB233977W

  In my opinion it's the wrong way to solve this problem. I mean I don't think that if it's a good idea to change parts of the motherboard, chips or anything else on your own.
  You are 100% sure that there is problem with sound chip?

  The same happens when you use headphones or external speakers?

• Re: Click on Satellite A300 - noisy HARD drive - strange of sound while booting

  Hi all

  I'm new and I would try to solve some problems with my new laptop * SATELLITE A300-1MZ * (with Vista) and * its hard disk * (a MHZ250BH of Fj-simens).

  I noticed that he is very mechanical in the normal conditions of use, in fact, when I turn on my computer, I hear a clear rattling and his mechanic from the HDD at different times also when there should be no disk activity.
  * Particularlly every 3-5 seconds * I hear a very strange noise as a small but very distinguible mechanic "CLAC" (is not refer to number of cycle ordefrag or indexing workload). Ditto on my ubuntu LINUX distro.
  However the phone never crashes

  _It first start Appareed and it's very noise_.
  I would ask if this is normal... It appeared regardless of the AC or battery power source.

  I just make a SMART software which is no problem, but I'm very worried about this problem.
  By phone, I just say all this to the center of Toshiba in my country, but for them all right. The laptop works ok.

  Not to mention that I found that * HDD * becomes * hot * also if there are no programs or processes that use it.
  He begins to 29a ° - 31Â ° and it gets hot with normal use (35 ° - 36Â ° after finished booting and after 30-40 min temperature is become more warm-42a ° - 46Â °, when its average temperature is ° - 48Â ° 46a - imagine if I turn for example a virus scan or a very hot video coding software-It to become: 50a ° - 55Â °.) (I try always not to overcome this final temperature). What is the maximum?

  * I hope you can give me an explanation to the problem.*
  * I ask if this is a problem common to other A300 owners.*

  For my personal reflection, that noise, it is very distinguible for a cooler quiet fan system (infact my dual core is 43a ° with normal use)
  Infact I would like to find a system to enable more cool fan (I have just seen in the bios and utilities from Toshiba but found nothing to that effect)

  Finally, I would like to know if the * battery time * 1h30mins (with the symmetric mode) is acceptable for a new laptop (with save mode is 1h40mins max).
  * I hope your support and I apologize for my language school *.

  Thanks y'alls.

  Hello

  I think that it s nothing wrong with your HARD drive.
  I have two cell phones and a PS3 at home.
  The HARD drive in a laptop made similar clicking sound. In addition, I noticed the same sound in the PS3. Since the upgrade to 500GB drive HARD makes the similar sound as the HARD drive in my notebook.
  I think that it s nothing wrong with the HARD drive and eventually it s nothing serious.

  > Finally, I would like to know if the battery of 1h30mins (with the symmetric mode) is acceptable for a new laptop (with save mode is 1h40mins max).
  Battery working time depends on the use of the laptop.
  The battery lasts a shorter time when to implement applications performance on the laptop. Also if the brightness of the display is set to the highest level, the battery needed to dump a lot more quickly.
  So I think 1.30 min is OK for the laptop. Of course, you can buy a stronger battery in order to use the laptop longer with battery power.

• Re: Satellite L40: strange sound USB

  Hi everyone :)
  First of all sorry for my English...

  I recently purchased a L40 - 17U satellite with vista home premium.

  Everything works fine, but I do not understand one thing...

  When I close the Panel/lid and computer goes to sleep/hibernate play a sound (exactly its system - as when disconecting usb). When I open the lid and computer wakes up and plays a sound too, as connection usb... but it's strange, the sound is without ALL the usb devices connected... There is no USB device connected to one of the three usb ports...

  All the works of devives (if logged in) usb very well before and after putting into hibernation, there is no problem with usb, next to that strange noise... There may be any internal device that is disconnected and connected when hibernate? It is not a RTL8187B wlan card (I found somewhere on the internet information, from a guy who has the same sound in his L40, he took off the wlan card and the noise was still there... but for this, no info on what causes this noise)

  I have in my fujitsu siemens Li2727 Office book, and there is no noise like that when going to Hibernate...

  And my question is:
  Is this normal? You have in your L40 the same? What is this mean sound?

  Thanks in advance
  Tom

  Eventually it s only a problem of Vista;

  I found this article Ms knowledge base:

  * + A USB device may no longer work correctly when Windows Vista comes out of standby or hibernation + *.
  http://support.Microsoft.com/kb/928631/en-us

  Check it out.
  Maybe it helps.

  Good bye

• Satellite C660 - 1LTD Strange grinding / vibrating noise when I watch videos

  Hello

  I'm new and I have a laptop series Satellite C660-1LD.

  Sometimes when I watch videos, there is a short sound of a noise and the best way to describe a vibration, grinding noise. The noises are not persistent, they come in short explosions.

  Sorry for the wrong description.

  Please can someone help?

  I'll be happy to give you any information you might need.

  > Grinding not strange all sounds far more

  Thanks for your comments and good to know that solve you the problem.

• How to change the tempo of the bass guitar? no weird noise.

  I clicked on the change of tempo to follow on a bass guitar recorded, but it appears totally artificial and strange, sped upwards or downwards.

  I'm doing something wrong?   why it sounds so weird!

  Please can someone answer this!  It's the same thing if I transpose the bass, sounds strange wobbly sounds.

• Ticking for Macbook Pro 2015

  Hello, I had a problem. Just got my new Macbook Pro 15 inch 2015. And I'm constantly a strange ticking sound it, I think that its the bottom of the computer.

  https://youtu.be/soQKSHkRfHc

  What can cause this problem?

  The main suspect is the fan.  Make an appointment with an Apple store genius bar and have examined the MBP.

  Ciao.

• Satellite U200 - 181 built-in HDD ERROR

  "Toshiba Satellite U200-181", I bought 2 weeks ago. Recently (2-3 days ago) I have problem with built-in HARD drive.

  So the problem is that sometimes I get the "Built-in HARD drive ERROR" message when starting the laptop. This integrated "Disk ERROR" message appears from time to time and the system shuts down the HARD drive starts, but can start from other bootable devices. First time where the built-in "Disk ERROR" message took place, he was accompanied by a lot of strange pop sound beating from the inside of the laptop. All others

  "HARD disk ERROR" messages were not so strong and strange beating pops, but always with some pop sounds (not as strong as the premiere).

  To identify possible problems, I saved S.M.A.R.T. data log (see annex 1).

  Additional information: after I bought the laptop I ve made successful update BIOS version 1.40 version 1.50 strictly according to Toshiba site official instructions. After BIOS upgrade system works well, no ERRORS, no exceptions. But 3 days ago I received the message"built-in HARD disk ERROR '."

  Any ideas? Thank you.

  : #1

  ================================================== ==========
  This folder made by Active SMART
  http://www.ariolic.com/activesmart/
  ================================================== ==========

  S.M.A.R.T. status
  Date: 2007-01-18 20:05:32

  Model name: HTS541080G9SA00
  Serial number: MPBDL0XKKE3RBG
  Capacity: 80.0 GB
  Firmware: MB4OC60R
  Drive interface: IDE
  Current temperature: 35 ° C (95 F)

  ------------------------------------------------------------------------------------------------
  The name threshold value worst raw attribute value
  ------------------------------------------------------------------------------------------------
  1 (01) raw Read Error Rate 62 100 100 0
  2 (02) flow Performance 40 100 100 0
  3 (03) spin Up Time 33 253 253 55834574849
  4 (04) start/Stop Count 0 100 100 363
  5 (05) reallocated sectors count 5 100 100 0
  7 (07) seek error rate 67 100 100 0
  8 (08) seek Time Performance 40 100 100 0
  9 (09) hours powered 0 100 100 194
  10 (0a) Spin Retry Count 60 100 100 0
  12 (0C) device Power Cycle Count 0 100 100 256
  191 (BF) G-sense Error Rate 0 100 100 0
  192 (C0) stop retract Count 0 100 100 5177348
  193 (C1) Load/Unload Cycle Count 0 100 100 4300
  194 (C2) 0 157 157 231929348131 temperature
  196 (C4) reallocation Event Count 0 100 100 0
  197 (C5) current pending sector Count 0 100 100 0
  198 (C6) incorrigible sector Count 0 100 100 0
  199 (C7) Ultra DMA CRC Error Count 0 200 253 0
  ------------------------------------------------------------------------------------------------

  To my knowledge, the error sometimes because the BIOS can not find the HARD drive as a source of start-up. Perhaps because of the loss of connection or / and a malfunction of the HARD drive.
  Hmm, have you checked if the HARD drive is connected properly?
  The losing may be a strange reason for the beating POPS.

• Tecra A9 won't boot up until I'm not going to put pressure on certain place

  I have a problem with my PC toshiba laptop tecra a9.
  It does not start normally when I press the power upward button, but in some cases, when I set the pressure at the bottom of the laptop (somewhere in the middle between the RAM and the CPU modules). [I'm pressing here somewhere, but both CPU and motherboard seems to be OK | http://i44.tinypic.com/1zzs0tg.jpg]

  I disassembled the laptop several times, but I couldn't find anything about the cause, and I couldn't find the exact spot, because I didn't want to start while he was not assembled back.
  When I turn on my laptop, the screen remains black, but HARD DRIVE control custom light normally and the CPU fan crazy at maximum speed until I turn the laptop off ("beep coming, but it's a pretty strange as sound, beep dying")
  (don't know how to describe it, it's like I would have cut the power of the signal sound emitor and level wither away within 2 seconds).

  However, if I do not put pressure at this place and it presents itself, it starts perfectly and resist not stable I turn it off. I can also suspend-to-ram, but if I close the lid, im unable to exert pressure on this spot when I open the lid.
  So I can't suspend, close the lid, and then recover.

  I think that this could be solved somehow avoid something in post-test or maybe theres a sensor (idk). I heard on the internet that it could be linked to the power supply inside the laptop which is not very well connected
  [My symptoms are very similar as in this case | http://www.laptoprepair101.com/laptop/2006/01/02/toshiba-tecra-te2100-boot-problem/comment-page-20/]

  Oh I forgot, I have this problem since the time when my daughter down my laptop on the ground of couch - like fall of 40cm (this is why I believe that some might contact had been damaged or something).
  Thanks for any response or assistance.

  Hello

  > Oh I forgot, I have this problem since the time when my daughter down my laptop on the ground of couch - like fall of 40cm (this is why I believe that some might contact had been damaged or something).

  It is difficult to tell what's exactly or what part is exactly.

  I don't see any details that could be wrong on the picture

  But the region on the motherboard that you have marked showing the CPU.

  Maybe the CPU is not correctly connected to the plug. This could be due to the decline.

  Perhaps it would be useful to remove the cooling module and CPU and check it again

• Satellite Pro U400-130 begin to operate automatically in internet

  My Toshiba U400-130 appears to have a clean mind - if I go on a website, Ebay for example and start working through the sales process, with no outside assistance from me, the computer will return to the previous web page and maybe come back another web page to the original signature on the page. Frequently, by pressing the next button, I can get back to where I left off but not always - what can be the cause?

  I don't think I have a virus that I run Zone Alarm and Force field and you will have to be Houdini to get into the system.
  Please don't look on that as a challenge and every crook out to Christianity is now trying to access my machine!

  Hello

  This strange s sound a little magic
  It s good idea to use additional security tools and firewalls like Zone Alarm, but it is still a rest of risk that your system could be attacked by a virus, Trojan or similar malware

  In your case, I would recommend to recover the laptop using the Toshiba recovery disc. This recovery disk will format the whole HARD disk and install the whole system again.
  I think that the format of HARD drive is necessary and important to be 100% sure that the malware has been removed.

• Satellite M100 - no battery light

  Hello

  My Satellite M100 has a problem with the power. He has started about a month ago, when my computer turns off suddenly, and the power light is the only one left on, no battery light. The problem seemed to disappear, but recently the gaming laptop upward again. It stops randomly, or the power led will Flash quickly. And the battery light will turn on for half a second and turn off.

  Any ideas, thanks in advance
  Baldan11

  > It shuts down randomly, or the power led will Flash quickly. And the battery light will turn on for half a second and turn off.
  Very strange but sounds like something wrong with the electronic power supply on the motherboard.
  If the power led starts flashing then that would mean that a material error has been detected on the motherboard

  But just a question;
  Are you able to use the laptop connected only to battery or only adapter?
  Problems of charging the battery?

• Beep / his problem with Satellite A105-S4134

  Greetings,

  First time on your forums! I hope you can help! I own a computer repair company and had a customer with an A105-S4134. I installed Windwos XP Media Center, a week ago.
  I've done all the windows upgrades ect ect. It ran great for 5 days and then I get a call from the client, saying: it was "beep" at random times. This is when he started up to or at a time, just when he wanted to. I have re-installed the sound card, disabled the sound card and it will beep again. My client said its coming from the front right side of the computer.

  Any ideas would be wonderful! Just a little history on it. I installed a new motherboard, Intel chip, fan, hard drive, memory and of course the OS System.
  Please let me know if you have any questions, I would like to fix this 'beep '! Thank you!

  Shawn
  Puget Sound computer repair

  Hello

  Maybe the sound signal comes from the BIOS?
  As you know there is a speaker that creates a warning tone if an error has been detected.

  Sorry, but that's all I can say about this title, strange beeping sound

• Rattling Equium A100-007

  I have an Equium A100-007 (there don't seem to be many positions directly related to this model) that I bought in April 2007. I'm running Ubuntu 7.10, which normally works very well. But, sometimes, I'm a clock strange clicking sound coming under the keyboard near the upper right speaker, when this happens, the system freezes and the only way I can back to work is to turn it off with the switch.

  I have not found something strange in the system logs and my sessions of firefox (and others) restorable after reboot without problem. It happens more or less at random, but is perhaps more likely when I download something, or watch a dvd, but it seems not directly related to have many applications running. It's happened a couple of times a week lately (but I have my laptop on almost all day every day), even if it has occurred previously. The temp runs between 45 - 51º C... I think it's a little warmer than before.

  I can't find anything on this problem in any thread. And I don't know if it's a hardware or OS problem.
  I would be very grateful for any advice on troubleshooting or resolution of this problem.

  It is not easy to say what the problem may be here on this forum, we can only speculate on the possible reasons for this. Try to do some tests to see what this trigger occurs. Try to play MP3 and see if the click comes from speaker directly (without optical drive running).

  Also try DVD movie playback, but without the sound to see if this clicking noise has something to do with optical drive running. Sorry, but it's really not easy to say what can be the problem. You can also ask for professional help and contact the nearest authorized service.

• Tecra A7: effect of phantom trubrite screen

  Hello
  I have a new laptop TECRA A7-247, ATI X 1600 graphics, 15.4 trubrite "view. When you look at movies DVD, objects moving in a dark background to make a 'ghost' effect, like a trail of Comet.

  The strange thing is that a previous journal (exactly the same model), I had to come back for another problem, did not show for this purpose and he had BIOS version 2.00.
  This does have BIOS 2.10 (same version of the graphics driver) and seems to have a screen brighter, but with less contrast.

  BIOS have anything to do with the display?
  Anyone with this newest version of BIOS (on the Web site you will find only version 2.00) and the same problem?

  GCG

  Hmm. very strange.
  Sounds like you have a portable computer with BIOS that is not available on the Toshiba page.
  But it would be very interesting to know if this problem occurs with BIOS 2.0 on your laptop or if this hardware malfunction of s (display, Fl-inverter),
  I've never downgraded the BIOS, and if you do you don't have possibilities to retrieve version 2.1, because right now the BIOS 2.1 is not available on the page.