Suddenly cannot open new tab, immediately after an update of MSWindows7, or after the upgrade to Windows 10 - tired, all kinds of bugs, no luck.

Similar Questions

• HP Photosmart C6280: cannot print on C6280 wireless after the upgrade to Windows 10

  Cannot print on C6280 wireless after the upgrade to Windows 10. Have removed the device, but try to re install the printer when is not found. Can print if I connect USB. Tried to reload the driver using HP Support software help, but when he arrives at the end of the download fails.

  Hi @Ron9871,

  Welcome to the Forums of HP Support!

  I see that you are unable to get your printer HP Photosmart C6280 wireless printing. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I would like to try the steps in this guide, "offline" Status Message printer (Windows 10).

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  • Print a Page of Network Configuration menu of the printer front panel. Note: the IPV4 IP.
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.

  Please restart the router, the printer and the computer in this sequence.

  If you're still having problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  • Use the File Checker system to repair missing or corrupted system files. It's always a good idea to back up your data before proceeding.
  • File system check (SFC) analysis and repair system files & DISM to fix things that are not SFC.

  You can try to change your WSD printer port by a Standard TCP/IP port.

  To do this, you will need your current IP address printers.  The Network Setup page shows the parameters of network for the product. To print this page; Press the button of network () on the control panel of the product.

   

• Cannot use/register LR 6 after the upgrade to Windows 10

  Good evening

  Using Lightroom 6 DESKTOP application (no CC or clouds) on Windows 10.

  I upgraded my Windows 7 to Windows 10.

  I did not have to 'turn off' my computer before proceeding with the installation,

  Now, I try to reinstall Lightroom 6 and I get the message:

  "The xxxxxxx serial number is already in use by the maximum allowed value of computer.

  You must disable another computer or provide a different serial number... "

  I can not find on the Adobe web site where I can disable or reactivate my LR6 serial number to use on Windows 10.

  6 of Lightroom is already installed and enabled on my Mac Book Air (and works); As far as I KNOW, I can use the same serial number on my Mac laptop and my Windows desktop computer.

  
  

  Where should I go to the adobe web site to see which computer are enabled so that I can clean that?

  
  

  Thank you

  
  

  Max.

  
  

  HI Mel,

  I have reviewed your account and sent you a private message.

  Please go back to a private message.

  ~ UL

• Cannot connect to internet after a reboot before you uninstall and then reinstall the network card. (After the upgrade to Windows 7 from Vista)

  This problem started immediately after the upgrade to Windows 7 Ultimate (32 bit) to Windows Vista Ultimate (32 bit).  Again, I want to remind that I never had this problem before installing Windows 7.

  -After a reboot, I am presented with the impossible to connect the network indicator (yellow triangle with!) in the task bar.  (It was how I was welcomed after the installation of Windows 7 is said by the way).

  -The only way I found to regain connectivity is to uninstall and reinstall the network via the device manager card, date at which the computer always successfully connects and remains connected until the next reboot.

  Network card: Realtek RTL8168C (P) / 811C (P) Family PCI - E Gigabit Ethernet NIC (NDIS 6.20)

  Driver provider: Microsoft
  Driver date: 14/05/2009
  Driver version: 7.2.1127.2008
  Digital signer: Microsoft Windows

  Thus, we have solved the problem! There are two possibilities of your problems:
  1 company Adobe uses the Bonjour service , this service should be disabled.
  Computer > Manage > Services and Applications > Services => find the bonjour service (sometimes stated as long numbers), stop service and if the Disabled value. It works!

  2. If it is not signed as Bonjour service. Try to disable the service:
  Shutdown mDNSResponder .exe (he is represented by # Id_String1.6844F930_1628_4223_B5CC_5BB94B879762 #).

  It is installed with Adobe software. If you upgrade the Vista, it will generally many users problem!

• Cannot open new tab by going to the file/new tab (or CTRL + T or by clicking on the new field of the tab). One is to right-click on a link and choose open in a new tab.

  Cannot open new tab by going to the file/new tab (or CTRL + T or by clicking on the new field of the tab). One is to right-click on a link and choose open in a new tab.

  I found that the ASK toolbar is the culprit. I have no recollection of ever install Ask and wanted not just her in any case. Withdrawal fixed the problem.

• After the upgrade to windows 7, Warcraft3, Battlefield Viet Nam cannot run in 4:3 screen but 16:9

  After the upgrade to windows 7, Warcraft3, Battlefield Viet Nam cannot run in 4:3 screen but 16:9... my East of 1366 X 768, so the games are run with black screen on the left and right sides... What can I do? He has run well in Vista =]

  1366 x 768 is the strangest resolution that I've ever heard of. Your video card drivers helped "keep the proportions" and decided to not to stretch imagine because I assume that you can't choose this exact resolution in the game. If your monitor has an overdrive video or image format option, you can enable or disable that or if you have a NVidia card, you can change the picture format option in the properties of the video card.

  If you have an ATI card, then you're stuck with a proportional image: P
  

• After the upgrade to Windows 10 ALL my pictures are GONE! Lightroom started upward as if it were a completely new program. Tried the Adobe difficulty (all 3 steps) nothing.

  After the upgrade to Windows 10 ALL my pictures are GONE! Lightroom started upward as if it were a completely new program. Tried the Adobe difficulty (all 3 steps) nothing. What now?

  Hi lisah64134956

  Greetings.

  • Please specify what adobe patch are you talking about?
  • A you kept a backup pf your LR catalog and images somewhere before moving on to Windows 10.
  • You have access to your original images, or they went too?
  • Try to search the catalog using windows search, .lrcat is the extension of the catalogue, see if you find something.

  Concerning

  Rohit

• DeskJet 2546 b: Wireless print job stays in queue and poster printer offline after the upgrade to Windows 10

  I write a fix I found for a pretty annoying problem involving 10 Windows and HP wireless printers.

  My Deskjet 2546-b printer was printing OK wireless to the point 8.1 of Windows until that I upgraded my computer to Windows 10. Immediately after I upgraded to Windows 10, I could not scan, so I reinstalled the printer software and has worked for a day or two and then the printer would print not unless I restarted the printer or the computer - sometimes 2 or 3 times. This went on for a few weeks, sometimes it would be nice, sometimes, usually after the computer restarts, he would simply go offline. Once, he went offline 3 times when I was printing about 20 postage labels, recently he went 1 week without any problems.

  Long story short, after a lot of troubleshooting and to help a friend to HP, I found the problem to be associated with the WSD/service Port in Windows 10. My printer still maintains a stable connection with my Netgear router (wireless to the printer light stays on blue) and I was able to scan from the HP software and I could ping the printer... but printing would be just stuck in the print queue (the spooler service) and the printer showed offline in the queue, hardware and windows devices , or when printing from a program like Windows.

  I learned that if I went in devices and printers, until I sent a print job, if the printer showed offline, I could save time by restarting the printer simply and he would come every time (less painful) online.

  

  But it's just a solution and not a solution.

  Nothing worked... not even print and scan doctor. The final fix that worked was to define an IP address manually for the printer, and then I put the print driver to use a standard TCP/IP port.

  Here is the step by step. Your printer must already be connected to your network (solid blue on printer).

  Step 1: Make sure your printer uses a manual IP address

  (1) to obtain the IP address of your printer:

  • If your printer has a control panel with a menu, it's easy... Just look in the settings menu without wire/report and write your printer IPv4 address.
  • If your printer is not a menu of fancy and repower the computer and printer HP Print and Scan Doctor network menu display use (wireless), or you can connect to your router from a web browser (usually 192.168.1.1) and look at attached IPs (like me). Some printers can also print a report of the network when you hold down some buttons everything back up and running, but you will need to search the web site of the Internet or HP to find the process for your printer model - the report displays the IP Address of the printer.

  (2) once you have the IP address of the printer number, type this information in a web browser... like 192.168.1.x (where x is the last number of your printer)

  Web page of the printer should find - otherwise, use another browser (you can use a tablet or iPad if you want). HP has several different forms of printing of web pages (embedded web servers) depending on your printer model, but they all have a large number of parameters.

  (3) since the network tab or section, look for a manual IP address configuration.

  

  (4) suggest an IP address or type in a new.  I've personally used suggest and then replaced by the last number 241. You want to use a high number, something in the order of 240 to 250 to reduce the risk of problems caused by your router assign this number to something else on your network. Note the 4 digits for the new IP address manual, you will use them later.

  5) click apply and close the web page of the printer.

  Step 2: Make the print driver using the manual IP address of the printer

  Open the devices and printers in Windows, right click on your printing device and select printer properties. Follow the prompts to get the WSD port and on a new local port...

  

  1) click on the ports tab.

  (2) add the Port.

  (3) click on after the first screen, and then click new port type.

  (4) enter the IP address of the printer.

  (5) next.

  (6) select the new port.

  7) click OK.

  You have now two pilots displayed in the printers and devices window, you can now print... but you might not be able to scan and the HP printing software may not work as he might want to lets you add a new printer when you open it... If Yes, proceed to step 3.

  Step 3: Remove print devices and install a new one.

  Need to do this to get the software back HP synchronized so you can scan.

  (1) right click 2 print devices listed in the window of your printer and remove them by clicking on remove device.

  (2) open the HP printer Assistant software (from the icon on the desktop or you can search Windows by using the name of your printer).

  (3) installation/add a new printer... go fast and a new device icon is added to the printers and devices window.

  4) return to the printers and devices window and open the properties of the printer again for your printer icon.

  5) go to the ports tab (yet) and you'll see a new selected WSD port, select Port Standard, you created earlier in step 2.

  (6) you have now two print devices in the window (again), but now everything should work.

  These two devices alone from here on out. Do not remove one and everything should work fine. At least it worked for me. I hope it works for you. I'm hoping a Windows update resolves this problem soon, I see many people who cannot print or scan wireless after they upgraded - not just the stuff of HP.

• Could not find photos after the upgrade to Windows 7

  Bridge worked very well under Vista, but after the upgrade to Windows 7, I can't find one of my photos with bridge files.  Photoshop CS4 find them OK and made Lightroom, but for some reason Bridge does not list the sub folders.  If I click on libraries, he says "no file".  It does not list the pictures or my pictures.  I'm totally stumped.

  AlAugustine wrote:

  I tried all combinations of ctrl-click, click and ctrl, etc, I can think of but nothing reveals the reset box.  When I double click on the desktop icon, it loads almost instantly leaving no time to press ctrl before loading.

  One thing I did not mention, is that you must check that the bridge is already done in the background.  Open the Task Manager and click the processes tab and see if bridge.exe is listed.  If program so quit smoking.

  If you have the possibility of automatically loading at startup deck, I recommend that deactivate you in the Advanced preferences file.  It causes more problems than it solves.

• Problem with a keyboard key of T440 after the upgrade to Windows 10

  Hello world

  I have a Brazilian keyboard layout (ABNT2) on my T440 and I am facing a problem after the upgrade to Windows 10. The new version of Windows recognizes this key:

  

  As long as the "CTRL on the right" (commom on other layouts).

  Everyone was faced with a similar problem or have any clues as to what might solve this problem?

  Thanks in advance,

  Felipe

  Solved.

  Do more research, I fount out is an old bug with Lenovo's Thinkpad laptops with this Brazilian keyboard.

  If you are facing the same problem, use this registry tweak and the problem is solved:

  http://ZTop.com.br/WP-content/uploads/2009/11/thinkpad_abnt_win7.zip

  (the file name indicates "win7" but it also works for Windows 10)

• After the upgrade of Windows Windows 7 10, could not recover my product key.

  Original title: windows 7

  After the upgrade to windows 10 windows 7, could not recover my product key. When I connect my system am get notification that you may be victim of software counterfeiting and copy of windows is not genuine. you do me too much this error code. 0xC004F057. Please help me to recover my product key. my windows does not work after the upgrade as well.

  I suggest that you run the diagnostic tool Microsoft Genuine Advantage in normal mode and copy and paste the results into a response for further analysis:

  http://go.Microsoft.com/fwlink/?LinkId=52012

  Run the tool and when it ends, click the copy button, open a text such as Word or Notepad file and select Edit, paste. You can paste directly into an answer here. Open a response, right click and select Paste.

• DVD player not recognized after the upgrade to windows 8

  I write this to document some odd behavior, that I lived after the upgrade to Windows 8 in the hope that it might save some grief for others.  Of course, if someone could explain why this problem occurs, I'd be very interested/grateful for an answer.

  I recently updated my computer from Vista Ultimate to Windows 8.  I did a clean install of Windows 8, because there is nothing special about the machine I wanted to preserve.  In all cases, the upgrade went without a hitch and I was soon back up with Windows 8 as my OS (I really like, btw).

  The only oddity I noticed after the upgrade is that my DVD drive was not recognized by the operating system.  Remember, this is the same DVD player that was used to install the OS, so I found it rather peculiar.  After a bit of lost time, try software solutions theoretical I started to play with the equipment.

  My motherboard is an ASUS M3A78-EM.  My hard drive is attached to the SATA1 port and my DVD player is plugged into the SATA2 port.  I removed the DVD drive from SATA2, plugged into SATA3, restart Windows 8 (from HDD on SATA1) and Windows 8 now recognizes the drive!

  I thought it was really weird, so I stop, put the DVD on SATA2 drive, rebooted, and the drive was no longer available in Windows 8.

  OK, so I thought that maybe the SATA2 channel was bad (even if he had worked at the Windows 8 DVD installation, just an hour or two before), so I put my HDD on SATA2 and the DVD drive on SATA1.  After doing this, Windows 8 start very well (so there is nothing wrong with SATA2), and it recognizes the DVD on the SATA1 drive.

  OK, so I did that for a while, and virtually all combinations I tried worked as long as the DVD player is not plugged in SATA2.

  I cannot live with that, but thought it was really strange.  Also, I note that the old operating system (Vista) was acknowledging the same DVD player while it was plugged on SATA2.  This leads me to believe that the problem has something to do with Windows 8, but I can't imagine what could be the cause.

  Thanks dude.  After you create this registry key/value and restart Windows 8 was able to finally see my DVD drive on SATA2.  =)

• change input key after the upgrade to windows 8

  I use the pavilion dv6-7012tx laptop, recently I've updated the Windows 8 operating system and then upgrade when you press (shift + 2) gives me "while pressing on (shift +') gives @ may I know what is the problem.is there solutions."

  Hello okkarai1991. I understand that you have some problems with your keyboard after the upgrade to Windows 8. More specifically you get incorrect symbols when you use the combination of keys shift +. Is this correct?

  Though according to me, there is a setting in Windows itself, I would like to add that HP has not released drivers for all models of laptops for Windows 8 yet. Most of the models purchased after October 1, 2011 should be supported. This site has more information on HP and the upgrade to Windows 8.

  This looks like a case of Windows using a keyboard that is incorrect. Each language has several layouts depending on the region, it seems that you have one of the other selected. This is a correction which is normally found in Control Panel. The process to access the control panel is a bit different in Windows 8, so I'll give you detailed instructions.

  1. Press the Windows key to take you to the view of the office.
  2. Move your mouse to the upper right corner of the screen and move it to the bottom, this opens the bar of charms.
  3. Select settings in the bar of charms, then select Control Panel. Then select the Language Options.
  4. Click Add an input method, and then select 'QWERTY-US.'
  5. Remove the old method of entry, leaving only QWERTY U.S. and click OK.
  6. Restart the computer and verify that your work of combinations shift + you want.

  I hope it's useful!

• Lightroom not responding do not develop after the upgrade to windows 10

  After the upgrade to windows 10, Lightroom will not work in develop after importing new photos. Can anyone help please.

  Alan

  Hi Alan,

  Please refer to this thread CC Lightroom freezes when develop mode and disable the use of the GPU in Lightroom.

  Let us know if that helps.

  Kind regards

  Assani

• After the upgrade to windows 10, my dreamweaver has stopped working. Could someone give me a solution for this? I really need DW!

  After the upgrade to windows 10, my dreamweaver has stopped working. It starst and lasts 30 seconds and never work again.

  Could someone give me a solution for this? I really need DW!

  Problems during the installation or opening Dreamweaver on Windows 10